Simultaneous determination of lead and cadmium in various environmental and biological samples by differential pulse polarography after adsorption of their morpholine-4-carbodithioates onto microcrystalline naphthalene or morpholine-4-dithiocarbamate-CTMAB-naphthalene adsorbent

A highly selective, sensitive and rapid differential pulse polarographic method (DPP) has been developed for the simultaneous estimation of trace amounts of lead and cadmium in standard alloys, biological and environmental samples. The morpholine-4-carbodithioates of the samples were absorbed on microcrystalline naphthalene in the pH range of 5-10 for lead and 3.4-11 for cadmium. The metal complexes were desorbed with 10 ml of 1M HCl and determined simultaneously with a differential pulse polarograph. These metals can alternatively be quantitatively adsorbed on morpholine-4-dithiocarbamate-cetyltrimethylammonium bromide-naphthalene adsorbent packed in a column and determined similarly. The detection limits are 0.14 ppm for Pb and 0.014 ppm for Cd at minimum instrumental settings (signal-to-noise ratio = 2). The linearity is maintained in the concentration ranges of Pb, 0.7-15 ppm and Cd, 0.07-10 ppm with a correlation factor of 0.9997 and relative standard deviations of 0.95 and 0.81%, respectively. Various parameters such as the effect of pH, volume of aqueous phase, and interference of a number of metal ions on the estimation of lead and cadmium have been studied in detail to optimize the conditions for their simultaneous estimation in various biological and environmental samples.     

Differential pulse polarographic determination of trace amounts of vanadium and molybdenum in various standard alloys and environmental samples after preconcentration of their morpholine-4-carbodithioates on microcrystalline naphthalene or morpholine-4-dithiocarbamate cetyltrimethyl-ammonium bromide-naphthalene adsorbent

A highly selective, sensitive, and fairly rapid and economical differential pulse polarographic (DPP) method has been reported for the determination of trace amounts of vanadium and molybdenum in standard alloys and various environmental samples. The morpholine-4-carbodithioates of these metals were retained (>99% recovery) quantitatively on microcrystalline naphthalene in the pH range 4.5-6.9 for vanadium and 1.5-4.5 for molybdenum. These metals were determined by DPP after desorption with 10 ml of 1 M HCl. Vanadium and molybdenum may also be preconcentrated by passing their aqueous solutions under similar conditions on morpholine-4-dithiocarbamate CTMAB-naphthalene adsorbent packed in a column at a flow rate of 1-5 ml min(-1) and determined similarly. The detection limits are 0.20 ppm for vanadium and 0.04 ppm for molybdenum at minimum instrumental settings (signal to noise ratio=2). The linearity is maintained in the following concentration ranges, vanadium 0.50-10.0 and molybdenum 0.10-9.0 ppm, with a correlation factor of 0.9996 (confidence interval of 95%, slopes 0.0196 and 0.01497 muA mug(-1), intercepts 3.65x10(-3) and -1.92x10(-3) respectively) and relative standard deviation of 1.1% in the microcrystalline method, while in the column method, the linearity is maintained in the concentration ranges, 0.50-6.5 for vanadium and 0.10-5.5 ppm for molybdenum with correlation factor of 0.9994 (with confidence interval of 95%, slopes 0.0194, 0.015 muA mug(-1), intercepts 3.60x10(-3) and -1.90x10(-3) respectively) and relative standard deviation of 1.4%. Various parameters such as the effect of pH, reagent, naphthalene and CTMAB concentrations, volume of aqueous phase and interference of a large number of metal ions on the estimation of vanadium and molybdenum have been studied in detail to optimize the conditions for their voltammetric determination at trace level in various standard alloys and environmental samples.     

Differential pulse polarography determination of indium after column preconcentration with [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent or its complex on microcrystalline naphthalene

A highly selective, sensitive and economical differential pulse polarographic method has been developed for the determination of trace amount of indium in various samples after adsorption of its 1-(2-pyridylazo)-2-naphthol on naphthalene in the pH range of 6.5-11.5. After filtration, the solid mass is shaken with 8 ml of 1 M hydrochloric acid and indium is determined by differential pulse polarography (DDP). Indium can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. The detection limit is 0.2 ppm (signal to noise ratio=2) and the linearity is maintained in the concentration range 0.8-125 ppm with a correlation coefficient of 0.9994 and relative standard deviation of +/-0.96%. Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of indium have been studied in detail to optimize the conditions for determination in various samples.     

Differential pulse polarographic determination of tin in alloys and environmental samples after preconcentration with the ion pair of 2-nitroso-1-naphthol-4-sulfonic acid and tetradecyldimethylbenzylammonium chloride onto microcrystalline naphthalene or by column method

A highly selective, sensitive, rapid and economical differential pulse polarographic method has been developed for the determination of trace amount of tin in various standard alloys and environmental samples after adsorption of its 2-nitroso-1-naphthol-4-sulfonic acid-tetradecyldimethylbenzylammonium chloride on microcrystalline naphthalene in the pH range of 8.7-10.6. After filtration, the solid mass is shaken with 8-10 ml of 3.5 M hydrochloric acid and tin is determined by differential pulse polarography (DPP). Tin can alternatively be quantitatively adsorbed on 2-nitroso-1-naphthol-4-sulfonic acid-tetradecyldimethylbenzylammonium-naphthalene adsorbent packed in a column and determined similarly. The detection limit is 0.15 mug ml(-1) (signal to noise ratio=2) and the linearity is maintained in the concentration range 0.5-220 mug ml(-1) with a correlation coefficient of 0.9995 and relative standard deviation of +/-0.88%. Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of tin has been studied in detail to optimize the conditions for determination in standard alloys and environmental samples.     

Differential pulse polarographic determination of lead in standard alloys and biological samples after separation and preconcentration with PAN

A highly selective, sensitive, rapid and economical differential pulse polarographic method has been developed for the determination of trace amount of lead in various samples after adsorption of its 1-(2-pyridylazo)-2-naphthol (PAN) on naphthalene in the pH range of 8.4 - 11.5. After filtration, the solid mass is shaken with 9.0 ml of 1 M hydrochloric acid and lead is determined by differential pulse polarography (DPP). Lead can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. The detection limit is 0.1 microg/ml (signal to noise ratio = 2) and the linearity is maintained in the concentration range 0.3 - 300 microg/ml with a correlation coefficient of 0.9996 and relative standard deviation of +/- 1.1%. Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of lead has been studied in detail to optimize the conditions for determination in alloys and biological samples.     

N-Methylethylxanthocarbamate as an Analytical Reagent: Differential Pulse Polarographic Determination of Cadmium in Standard Alloys, Biological and Environmental Samples after Adsorption of its Complex on Microcrystalline Naphthalene

N-methylethylxanthocarbamate has been used as an analytical reagent for the determination of trace amounts of cadmium in standard alloys, biological, and environmental samples. The reagent has been found to form a water insoluble complex with cadmium. It is quantitatively adsorbed over microcrystalline naphthalene in the pH range 2.5 to 12.0. The metal complex is desorbed with HCl and cadmium determined with a differential pulse polarograph. The detection limit is 0.05 ppm (signal-to-noise ratio = 2) and the linearity is maintained in the concentration range 0.2–25 g/ml, with correlation coefficient of 0.9995 and a relative standard deviation of ±0.81%. Characterization of the electroactive process includes an examination of the degree of reversibility. Various parameters, such as the effect of pH, reagent concentration, amount of naphthalene, volume of aqueous phase, and the interference of a large number of metal ions on the determination of cadmium, have been studied in detail to optimize the conditions for its determination in various complex materials.     

Differential pulse polarographic determination of lead in complex materials after adsorption of its N-methylethylxanthocarbamate complex on microcrystalline naphthalene or on N-methylethylxanthocarbamate-benzyldimethyltetradecylammonium-naphthalene adsorbent

Lead is quantitatively adsorbed as the lead N-methylethylxanthocarbamate (MEXC)-benzyldimethyltetradecylammonium (BDTA) ion pair complex on microcrystalline naphthalene in the pH range 4.0-11.0. The metal is desorbed with HCI and determined by differential pulse polarography. Alternatively lead can be quantitatively adsorbed on the adsorbent (MEXC-BDTA-naphthalene) packed in a column at a flow rate of 1-2 mL/min and determined similarly. Dissolved oxygen is removed by adding a few milliliters of 4% NaBH4 solution. The detection limit is 0.12 microg/mL at the minimum instrumental settings (signal-to-noise ratio, 2). Linearity was obtained over the concentration range 0.3-20.0 microg/mL with a correlation factor of 0.9998 and a relative standard deviation of +/- 0.98%. Various parameters, such as the effect of pH, volume of aqueous phase, flow rate, and the interference of a large number of metal ions and anions, were studied in detail to optimize the conditions for the trace determination of lead in various standard alloys, standard biological materials, and environmental samples.     

Differential Pulse Polarographic Determination of Gallium and Niobium in Samples After Preconcentration of Their Quinolin-8-Olate Complexes on Microcrystalline Naphthalene

Abstract

Gallium and niobium react with quinolin-8-ol to form water insoluble complexes which are quantitatively adsorbed on microcrystalline naphthalene from the large volume of their aqueous solutions in the pH range of 3.5 - 8.2 and 6.2 - 9.4, respectively. After filtration, the metal complexes were desorbed with 10 ml of HCl (1M for Ga and 11 M for Nb) and determined by using a differential pulse polarograph (DPP). The dissolved oxygen is removed by adding a few milliliters of 4% NaBH₄ solution in the case of gallium. The detection limits are 0.04 ppm for gallium and 0.05 ppm for niobium at the minimum instrumental settings (signal to noise ratio = 2). The linearities are maintained in the concentration range 0.1 - 5.0 ppm for gallium and 0.4 - 6.0 ppm for niobium with correlation factors of 0.9997 and 0.9996 and relative standard deviations of 0.81 and 0.95%, respectively.

Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH volume of aqueous phase, reagent and naphthalene concentrations and the interference of a large number of anions and cations on the estimation of these elements were studied in detail. The method is found to be highly selective, fairly sensitive, rapid, simple and economical. It has been applied for the trace determination of gallium and niobium in various standard alloys and may be applied safely for the analyses of complex materials like environmental samples and ores.

     

Flame atomic absorption spectrometric determination of trace amounts of manganese in alloys and biological samples after preconcentration with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and ammonium tetraphenylborate on microcrystalline naphthalene or by column method.

Manganese is quantitatively retained on 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-ammonium tetraphenylborate with microcrystalline naphthalene or by a column method in the pH range 7.5-10.5 from large volumes of aqueous solutions of various samples. After filtration, each solid mass consisting of the manganese complex and naphthalene was dissolved with 5 ml of dimethylformamide and the metal was determined by flame atomic absorption spectrometry. Manganese complex can alternatively be quantitatively adsorbed on ammonium tetraphenylborate-naphthalene adsorbent packed in a column and determined similarly. About 0.1 microgram of manganese can be concentrated in a column from 500 ml of aqueous sample, where its concentration is as low as 0.2 ppb. Eight replicate determinations of 1.0 ppm of manganese gave a mean absorbance of 0.224 with a relative standard deviation of 1.8%. The sensitivity for 1% absorption was 19 ppb. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of manganese in various standard samples.     

Quantitative Estimation of Ruthenium(III) Using Morpholine-4-Carbodithioate as a New Analytical Reagent

Ruthenium(III) has been precipitated gravimetrically in the pH range 7.0-8.5 with morpholine-4-carbodithioate and determined by weighing as a black complex (C₅H₆ONS₂)₃ Ru after drying at l00–110°C. The interference of the various metal ions has been avoided by using an ammonical mixture of EDTA and tartrate (1:1 molar ratio). The complex is thermally stable up to l60°C.     

Column preconcentration of trace manganese with the ion pair of 2-nitroso-1-naphthol-4-sulfonic acid tetradecyldimethylbenzyl-ammonium chloride supported on naphthalene and determination by derivative spectrophotometry

A column preconcentration method has been developed for the determination of trace amounts of manganese by preconcentration on 2-nitroso-1-naphthol-4-sulfonic acid (nitroso-S)-tetradecyldimethylbenzylammonium (TDBA) naphthalene as an adsorbent using a simple funnel tipped glass tube. Manganese reacts with nitroso-S to form a water soluble brown colored chelate anion. The chelate anion forms a water insoluble Mn-Nitroso-S-TDBA ion pair on naphthalene packed in a column in the pH range 9.6-10.5 at a flow rate of 1-2 ml/min. The solid mass consisting of manganese complex and naphthalene is dissolved in 5 ml of dimethylformamide (DMF) and the metal determined by second derivative spectrophotometry. The calibration curve is linear in the concentration range 0.25-35.0 micrograms of Mn in 5 ml of the final DMF solution. Eight replicate determinations of 25 micrograms of standard manganese solution give a mean peak height of 4.0 with a correlation coefficient of 0.9995 and relative standard deviation of +/- 1.1%. The sensitivity was calculated to be 0.502(d2 A/d lambda 2)/microgram ml-1 from the slope of the calibration curve. The detection limit was 0.020 microgram ml-1 for manganese at the minimum instrumental settings (signal to noise ratio = 2). Various parameters effecting the method such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of manganese have been evaluated to optimize the conditions for its determination in standard alloys and biological samples.     

Differential Pulse Polarographic Determination of Trace Amounts of Lead in Alloys and Biological Samples after Column Preconcentration Using Nitroso-S and TDBA

A highly selective, sensitive, rapid, and economical differential pulse polarographic method has been developed for the determination of trace amounts of lead in various standard alloys and biological samples after the adsorption of its 2-nitroso-l-naphthol-4-sulfonic acid (nitroso-S)—tetradecyldimethylbenzylammonium (TDBA) chloride on microcrystalline naphthalene in the pH range of 8.0–10.5. After filtration, the solid mass is shaken with 9.0 mL of 1 M hydrochloric acid, and lead is determined by differential pulse polarography (DPP). Lead can alternatively be quantitatively adsorbed on 2-nitroso-l-naphthol-4-sulfonic acid-tetradecyldimethylbenzylammonium-naphthalene adsorbent packed in a column and determined similarly. In this case, 1.0 g of lead can be concentrated in a column from 500 mL of an aqueous sample in which its concentration is as low as 2 ng/mL. Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters, such as the pH effect, volume of aqueous phase, HCl concentration, reagent concentration, naphthalene concentration, shaking time, and the interference of a number of metal ions on the determination of lead were studied in detail to optimize the conditions for determination in standard alloys and standard biological samples.     

Atomic absorption spectrometric determination of ultra trace amounts of zinc after preconcentration with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and ammonium tetraphenylborate on microcrystalline naphthalene or by column method

Zinc is quantitatively retained on 2-(5-bromo-2-pyridylazo)-5-diethylamminophenol (5-BrPADAP)-ammonium tetraphenylborate with microcrystalline naphthalene or by a column method in the pH range 7.5-9.0 from a large volume of aqueous solutions of various samples. After filtration, the solid mass consisting of the zinc complex and naphthalene was dissolved with 5 ml of dimethylflarmamide and the metal was determined by atomic absorption spectrometry. Zinc complex can alternatively be quantitatively adsorbed on ammonium tetrphenylborate-naphthalene adsorbent packed in a column and determined similarly. The calibration curve is linear 0.05-4.0 ppb in dimethylformamide solution. Eight replicate detenninations of 1.0 ppb of zinc gave a mean absorbance of 0.124 with a relative standard deviation of 1.3%. The sensitivity for 1% absorption was 0.035 ppb. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of zinc in various standard samples.     

Preconcentration of trace cobalt with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and tetraphenylborate onto microcrystalline naphthalene or column method and its determination by derivative spectrophotometry

Cobalt-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-tetraphenylborate ion associated complex is quantitatively adsorbed on microcrystalline naphthalene in the pH range 3.5-9.5 from a fairly large volume of the aqueous samples (preconcentration factor ~30). After filtration, the solid mass consisting of the cobalt complex and naphthalene was dissolved with 5 ml of dimethylformamide (DMF) and the metal determined by first-derivative spectrophotometry. The cobalt-5-Br-PADAP complex can alternatively be quantitatively retained on ammonium tetraphenylborate-naphthalene adsorbent filled in a column (preconcentration factor 120) in the same pH range and determined similarly. The detection limit is 30 ppb (signal-to-noise ratio=2) and the calibration curve is linear over 0.3-8.0 mug of cobalt in 5 ml of the final DMF solution. Eight replicate determinations of 1.0 mug of cobalt gave a mean peak height of 0.208 (at 611.5 nm) with a relative standard deviation of 1.2%. The sensitivity of the method is 1.04 (dA/dnm) ml mug(-1) found from the slope of the calibration curve. The interference of a large number of anions and cations on the determination of cobalt has been studied and the optimized conditions developed were utilized for its trace determination in various standard alloys and biological samples.     

Differential pulse polarographic determination of uranium(VI) in complex materials after adsorption of its trifluoroethylxanthate cetyltrimethylammonium ion-associated complex on naphthalene adsorbent.

Uranium(VI) is adsorbed as a uranium trifluoroethylxanthate (TFEX)-cetyltrimethylammonium (CTMA) ion-pair complex on microcrystalline naphthalene quantitatively in the pH range 4.2 - 7.0. Without cetyltrimethylammonium as the counter ion, the adsorption is hardly 70%. The metal has been desorbed with HCI and determined with a differential pulse polarograph. Uranium can alternatively be quantitatively adsorbed on TFEX-CTMA-naphthalene adsorbent packed in a column at a flow rate of 1 - 5 ml/min and determined similarly. A well-defined peak has been obtained in this medium at -0.20 V versus a saturated calomel electrode. Cyclic voltammetry, differential pulse polarography and D.C. polarography studies indicate that uranium has been reduced irreversibly under these conditions. The detection limit is 0.30 microg/ml at the minimum instrumental settings (signal-to-noise ratio of 2) (with a preconcentration factor of 10, the detection limit would be 30 ng/ml for uranium when the volume in the cell is 15 ml). However if the volume in the cell is 5 ml, it would have been 10 ng/ml with a preconcentration factor of 30. Linearity is maintained in a concentration range of 0.5 - 19.0 microg/ml (2.1 - 79.83 x 10(-9) M) with a correlation factor of 0.9994 and a relative standard deviation of +/-1.1% (in this case 7.5 microg may be concentrated from 150 ml of the aqueous sample where its concentration is as low as 50 ng/ml). Various parameters, such as the effect of the pH, volume of the aqueous phase, flow rate and the interference of a large number of metal ions and anions on the determination of uranium, have been studied in detail to optimize the conditions for its trace determination in various complex materials, like alloys, coal fly ash, biological, synthetic, and waste-water samples.     

Atomic absorption spectrometric determination of trace zinc in alloys and biological samples after preconcentration with [1-(2-pyridylazo)-2-naphthol] on microcrystalline naphthalene

An atomic absorption spectrometric method for the determination of trace amounts of zinc after adsorption of its [1-(2-pyridylazo)-2-naphthol] complex on microcrystalline naphthalene has been developed. This complex is adsorbed on microcrystalline naphthalene in the pH range 3.5-7.5 from large volumes of aqueous solutions of various alloys and biological samples with a preconcentration factor of 40. After filtration, the solid mass consisting of the zinc complex and naphthalene was dissolved with 5 ml of dimethylformamide and the metal was determined by flame atomic absorption spectrometry. Zinc can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. About 0.5 ng of zinc can be concentrated in a column from 200 ml of aqueous sample, where its concentration is as low as 2.5 pg ml-1. The calibration curve is linear in the range 0.1-6.5 ng ml-1 in dimethylformamide solution. Eight replicate determinations of 2 ng ml-1 of zinc gave a mean absorbance of 0.145 with a relative standard deviation of 1.5%. The sensitivity for 1% absorption was 0.061 ng ml-1. Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of zinc, have been studied in detail to optimize the conditions for the determination of zinc in various standard complex materials.     

Derivative spectrophotometric determination of iridium after preconcentration of its 1-(2-pyridylazo)-2-naphthol complex on microcrystalline naphthalene

Iridium is preconcentrated from the large volume of its aqueous solution using 1-(2-pyridylazo-2-naphthol) (PAN) on microcrystalline naphthalene in the pH range of 4.5-6.0. The solid mass after filtration is dissolved with 5 ml of dimethylformamide (DMF) and the metal determined by first derivative spectrophotometry. The detection limit is 20 ppb (signal to noise ratio = 2) and the calibration curve is linear over the concentration range 0.25-75.0 mug in 5 ml of the final DMF solution with a correlation coefficient of 0.9996 and relative standard deviation of +/- 1.1%. Various parameters such as the effect of pH, volume of aqueous phase, choice of solvent, reagent and naphthalene concentration, shaking time and interference of a number of metal ions on the determination of trace amount of iridium have been studied in detail to optimize the conditions for its determination in synthetic samples corresponding to various standard alloys and environmental samples.     

Determination of trace levels of manganese in various biological and environmental samples by atomic absorption spectrometry after solid-liquid extraction and preconcentration with the ion pair formed by the nitroso-S anion and the tetradecyldimethylbenzylammonium cation.

Manganese is quantitatively retained by 2-nitroso-1-naphthol-4-sulfonic acid (nitroso-S) and tetradecyldimethylbenzylammonium (TDBA) chloride on microcrystalline naphthalene in the pH range 9.5-10.6 from large volumes of aqueous solutions of various samples. After filtration, the solid mass consisting of the manganese complex and naphthalene is dissolved in 5 mL dimethylformamide and the metal is determined by flame atomic absorption spectrometry. Alternatively, the manganese complex can be quantitatively adsorbed on TDBA-naphthalene adsorbent packed in a column and determined similarly. About 0.2 microg manganese can be concentrated in a column from 400 mL aqueous sample with a concentration as low as 0.5 ng/mL. Eight replicate determinations of manganese at 0.8 microg/mL gave a mean absorbance of 0.156 for the final solution with a relative standard deviation of 1.4%. The sensitivity for 1% absorption was 23 ng/mL. The interference of a large number of anions and cations was studied, and the optimized conditions developed were used for trace determinations of manganese in various alloys, and in biological and environmental samples.     

Tetradecyldimethylbenzylammonium thiocyanate adsorbent supported on naphthalene for the preconcentration and determination of cobalt in aluminium alloys and steels using atomic absorption spectrometry

A solid ion-pair material produced from tetradecyldimethylbenzylammonium chloride (TDBA) and ammonium thiocyanate on naphthalene provides a simple, rapid and selective technique of preconcentrating cobalt from up to 200 ml of aqueous solution. Cobalt reacts with sodium 1-nitroso-2-naphthol-3,6-disulphonate (nitroso-R salt) to form a brown, water-soluble chelate anion. The chelate anion forms a water-insoluble Co-nitroso-R salt-TDBA complex on naphthalene packed in a column and trace cobalt is quantitatively retained on the naphthalene in the pH range 2.7–11.0 at a flow-rate of 2 ml min^?1. The solid mass is stripped from the column with 5 ml of dimethylformamide (DMF) and cobalt is measured by atomic absorption spectrometry (AAS) at 241 nm. The calibration graph is linear over the concentration range 0.5–15μg Co in 5 ml of dimethylformamide solution. Seven replicate determinations of 9 μg of cobalt gave a mean absorbance of 0.095 with a relative standard deviation of 1.7%. The sensitivity for 1% absorption was 0.0834μg ml^?1 (0.240 μg ml^?1 for direct AAS on the aqueous solution). The proposed method was utilized for the determination of cobalt in standard aluminium alloys and steel samples.     

Atomic absorption spectrometric determination of trace amounts of nickel after preconcentration with [1-(2-Pyridylazo)-2-Naphthol]-Naphthalene adsorbent or after adsorption of its complex on microcrystalline naphthalene

An atomic absorption spectrometric method for the determination of trace amounts of nickel after adsorption of its 1 -(2-pyridylazo)-2-naphthol complex on microcrystalline naphthalene has been developed. This complex is adsorbed on microcrystalline naphthalene in the pH range 4.5-7.8 from large volumes of aque ous solutions of various alloys and biological and environmental samples containing nickel. After filtration, the solid mass consisting of nickel complex and naphthalene was dissolved in 5 mL of dimethylformamide, and the metal was determined using a flame atomic absorption spectrometer at a wavelength of 232 nm. Alternatively, nickel can be quantitatively adsorbed on [l-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. The calibration curve is linear over the concentration range 2.0-100 Μg of nickel in 5 mL of the final dimethylformamide solution. Eight replicate determinations of 20 Μg of nickel give a mean absorbance of 0.072 with a relative standard deviation of 1.3%. The sensitivity for 1% absorption is 0.24 Μg/mL. Various parameters such as the effect of pH, the volume of the aqueous phase, and the interference of a large number of metal ions with the determination of nickel have been studied in detail to optimize the conditions for its determination in various standard alloys and biological and environmental samples. This article was submitted by the authors in English.