Determination of the Natural Dissolved Concentration of Zirconium in Seawater by Adsorptive Stripping Voltammetry

A voltammetric method was developed for zirconium determination as Zr(IV)‐cupferron‐oxalate‐diphenylguanidine complex based on adsorptive accumulation at the HMDE (E_peak=?0.95 V). The supporting electrolyte was a mixture of acetate/acetic acid (pH 4.6) and ammonium acetate (pH 5.7) solutions. E_ads=?0.6 V (vs. Ag/AgCl), t_ads=400 s, 10 mV s^?1 scan rate, and DP mode were the main parameters. The linear range was 0.033 to 3.3×10^?9 mol L^?1, and the LOD and LOQ (t_ads=400 s) were 0.77 and 1.6×10^?11 mol L^?1, respectively. The method was adequate for seawater samples, although not sufficiently sensitive for surface waters.     

Use of ultramicroelectrodes for determining lead in natural waters by stripping voltammetry

Anin situ obtained graphite-fiber-based thin-film mercury microelectrode was used for determining lead(II) in natural water by stripping voltammetry without removing oxygen and using no supporting electrolyte. Under the optimum voltammetric conditions (E _el = -1.2 V,t _el = 5 min,c _Hg(II) = 1 x 10^-7 M, ΔE = 40 mV, v= 105 mV/s), the calibration graph was linear in the range of actual lead(II) concentrations in natural waters. At a lead(II) concentration of 0.002 mg/L, the RSD was 11%.     

Square‐Wave Voltammetry of the Molybdenum‐1,10 Phenanthroline‐Fulvic Acids Complex: Redox Kinetics Measurements

The reduction process of molybdenum in the presence of fulvic acids and phenanthroline was investigated by square-wave voltammetry (SWV). The mixed-ligand complex of molybdenum exhibits a pronounced tendency to adsorb onto the mercury electrode surface. The electrode reaction proceeds as a surface process in which both components of the redox couple are firmly confined to the electrode surface. The kinetics of the electrode reaction is studied utilizing the properties of “split SW peaks” and “quasireversible maximum”. The kinetic parameters obtained with two different square-wave voltammetric methods are in good agreement. In 0.5 mol/L NaCl solution with pH 2.5 the kinetic parameters are: standard rate constant k_s=8±2 s⁻¹, cathodic electron transfer coefficient α=0.41±0.05, and number of exchanged electrons n=2. The SW kinetic measurements are confirmed by cyclic voltammetric method.     

Determination of Trace Copper by Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Modified Carbon Paste Electrode

A new method for the determination of trace copper was described. A multiwalled carbon nanotube modified carbon paste electrode was prepared and the adsorptive voltammetric behavior of copper‐alizarin red S (ARS) complex at the modified electrode was investigated. By use of the second‐order derivative linear sweep voltammetry, it was found that in 0.04 mol/L acetate buffer solution (pH 4.2) containing 4×10^?6 mol/L ARS, when accumulation potential is 0 mV, accumulation time is 60 s and scan rate is 100 mV/s, the complex can be adsorbed on the surface of the electrode, yielding one sensitive reduction peak at ?172 mV (vs. SCE). The peak current of the complex is proportional to the concentration of Cu(II) in the range of 2.0×10^?11–4.0×10^?7 mol L^?1 with a detection limit (S/N=3) of 8.0×10^?12 mol/L (4 min accumulation). The proposed method was successfully applied to the determination of copper in biological samples with satisfactory results, the recoveries were found to be 96%–102%.     

Voltammetric Determination of Cocaine Using Carbon Screen Printed Electrodes Chemically Modified with Uranyl Schiff Base Films

Chemically modified screen printed electrodes (CM‐SPE) using [UO₂(4‐MeOSalen)(H₂O)] ? H₂O films were employed in the voltammetric determination of cocaine. The chemical modification was performed by dip coating electrode surfaces (carbon, gold, and platinum) with methanolic solution containing the Schiff base complex with subsequent drying step at room temperature. The optimized amount of the chemical modifier over the working electrode was found to be 2.39 µg mm^?2 (geometric area). The voltammetric measurements were carried out in 50 : 50 v/v methanol:water solution containing 0.05 mol L^?1 KCl and 0.1 mol L^?1 LiCl as a supporting electrolyte without oxygen elimination by inert gas flow. The best results were obtained with carbon electrodes. Cocaine exhibits a well defined irreversible anodic peak current (i_pa) at a potential (E_pa) of 0.85 V vs Ag/AgCl. The current is directly proportional to the drug concentration. An optimal accumulation potential (E_prec), and time (t_prec) of ?0.80 V (vs Ag/AgCl), and 120 s, respectively, were determined. The linear dependence of i_pa with square root of scan rate (υ) indicates that the mass transport at the electrode surface is controlled by diffusion. An optimized scan rate of 100 mV s^?1 was obtained for analytical purposes. A limit of detection (LOD) and limit of quantification (LOQ) in 110 and 390 µmol L^?1, respectively, with intra and inter‐day repeatability of 2.61 % and 3.77 %, respectively, were obtained. In interference studies the proposed method demonstrated high specificity for cocaine in the presence of morphine and 3,4‐methylenedioxymethanphetamine. The above results demonstrate that this method provides a fast and low cost procedure for determination of cocaine in trace levels.     

Voltammetric Behavior of Semicarbazide at Graphene Modified Electrode and Application to Detection

Herein voltammetric behaviors of semicarbazide (SEM) are investigated by employing a graphene modified working electrode, which displays attractive electroanalytical properties. In the acetate buffer solution of pH 4.00, there is a well‐defined oxidative peak of SEM, attributing to the irreversible and adsorption‐controlled electrode reaction with 2 electrons participation. The values of apparent heterogeneous electron transfer rate constant k′_s with the redox are 0.0061 s^?1 and 0.0009 s^?1, respectively, for two scan rate section. After the experimental parameters, which influence the voltammetric responses of SEM, including supporting electrolyte, pH, accumulation time and accumulation potential, etc., are optimized, it is found that the anodic peak current of SEM is proportional to its concentration in the range of 4 ‐ 40 μmol/L with a detection limit of 1 μmol/L (S/N = 3). Then, an electrochemical method for detecting SEM quantitatively is developed successfully. The concentrations of SEM in fortified tap water samples are tested with satisfactory recovery, indicating that the novel method is strongly promising in the environmental monitoring application.     

Anodic Stripping Voltammetric Determination of Mercury in Water Using a Chitosan‐Modified Carbon Paste Electrode

Abstract

This paper describes the preparation and electrochemical application of a modified carbon paste electrode with chitosan for the determination of Hg(II) ions in water using anodic stripping voltammetry. Experimental parameters, including the pH of the supporting electrolyte, time and potential of accumulation and scan rate were investigated. The best voltammetric response was observed for a paste composition of 60% (m/m) of graphite powder, 20% (m/m) of chitosan and 20% (m/m) of mineral oil, with 0.1 mol/l NaNO₃ solution at pH 6.3 as supporting electrolyte, a preconcentration potential of ?0.2 V, preconcentration time of 270 s and a scan rate of 25 mV/s. Under these optimal experimental conditions, the voltammetric signals were linearly dependent on the Hg(II) concentration in the range of 9.99×10^?7 to 3.85×10^?5 mol/l with a detection limit of 6.28×10^?7 mol/l. Three “spiked” samples of water were evaluated using the proposed sensor, and results agreed with those obtained by a reference method at the 95% confidence level.     

Electrochemical Studies and Square‐Wave Adsorptive Stripping Voltammetry of Spironolactone Drug

Abstract

A sensitive and reliable stripping voltammetric method was developed to determine Spironolactone drug. This method is based on the adsorptive accumulation of the drug at a hanging mercury drop electrode and then a negative sweep was initiated, which yield a well defined cathodic peak at ?1000 mV versus Ag/AgCl reference electrode. To achieve high sensitivity, various experimental and instrumental variables were investigated such as supporting electrolyte, pH, accumulation time and potential, drug concentration, scan rate, frequency, pulse amplitude, convection rate and working electrode area. The monitored adsorptive current was directly proportional to the concentration of Spironolactone and it shows a linear response in the range from 1×10^?8 to 2.5×10^?7 mol l^?1 (correlation coefficient=0.999) and the detection limit (S/N=3) is 1.72×10^?10 mol l^?1 at an accumulation time of 90 sec. The developed AdSV procedure shows a good reproducibility, the relative standard deviation RSD% (n=8) at a concentration level of 1.5×10^?7 mol l^?1 was 1.4%, whereas the method accuracy was indicated via the mean recovery of 97.5%±2.04. Possible interferences by several substances usually present in the pharmaceutical formulations have been also evaluated. The applicability of this approach was illustrated by the determination of Spironolactone in pharmaceutical preparation and biological fluids such as serum and urine.     

Voltammetric Determination of 8‐Nitroquinoline Using a Silver Solid Electrode and Its Application to Model Samples of Drinking and River Water

This work is focused on the application of a silver solid electrode (AgE) for the development of modern voltammetric methods for the determination of submicromolar concentrations of biologically active compounds present in the environment. 8‐Nitroquinoline (8‐NQ), a well‐known chemical carcinogen, was chosen as a model substance. Differential pulse voltammetry (DPV) was used to study electrochemical behavior of 8‐NQ in different aqueous matrices. The following optimal conditions for determination of 8‐NQ in the concentration ranges from 2 to 100 µmol L^?1 were used: Britton? Robinson (BR) buffer of pH 3.0, the regeneration potentials cycles (E_in=?1000 mV, E_fin=?100 mV) and constant cleaning potential ?2000 mV. Practical applicability of AgE for the determination of micromolar concentrations of 8‐NQ was verified on model samples of drinking and river water.     

Voltammetric Determination of Allura Red AC onto Carbone-paste Electrode Modified by Silica with Embedded Cetylpyridinium Chloride

In current study the carbon-paste electrode modified by silica with embedded cetylpyridinium chloride for determination of Allura Red AC have been developed. The optimal conditions were determined to be for the square-wave voltammetric quantification: pH=2, E_ads=300 mV, t_ads=300 s, amplitude – 40 mV, frequency – 25 Hz and potential scan rate is 250 mV sec⁻¹. The calibration plot has linearity in the concentration ranges 0.04–0.2 μM and 0.2–1.00 μM. The LOD and LOQ are equal to 0.005 μM and 0.015 μM respectively. The crafted sensor has been applied successfully to model solutions and in jelly candies analysis with RSD no more than 10 %.     

Sensitive Electrochemical Determination of Catechol with a Graphene Modified Carbon Ionic Liquid Electrode

In this paper a graphene (GR) modified carbon ionic liquid electrode (CILE) was fabricated and used as the voltammetric sensor for the sensitive detection of catechol. Due to the specific physicochemical characteristics of GR such as high surface area, excellent conductivity and good electrochemical properties, the modified electrode exhibits rapid response and strong catalytic activity with high stability toward the electrochemical oxidation of catechol. A pair of well‐defined redox peaks appeared with the anodic and the cathodic peak potential located at 225 mV and 133 mV (vs.SCE) in pH 6.5 phosphate buffer solution, respectively. Electrochemical behaviors of catechol on the GR modified CILE were carefully investigated and the electrochemical parameters were calculated with the results of the electrode reaction standard rate constant (k_s) as 1.24 s^?1, the charge transfer coefficient (α) as 0.4 and the electron transfer number (n) as 2. Under the selected conditions the differential pulse voltammetric peak current increased linearly with the catechol concentrations in the range from 1.0 × 10^‐7 to 7.0 × 10^?4mol L‐1 with the detection limit as 3.0 × 10^?8mol L‐1 (3σ). The proposed method was further applied to the synthetic waste water samples determination with satisfactory results     

A Hydrogen Peroxide Biosensor Based on Room Temperature Ionic Liquid Functionalized Graphene Modified Carbon Ceramic Electrode

A room temperature ionic liquid (IL) 1‐butyl‐3‐methylimidazolium hexafluorophosphate functionalized graphene (GE) was prepared and a hydrogen peroxide (H₂O₂) biosensor was fabricated by immobilizing hemoglobin (Hb) into the IL‐GE composite film. UV‐visible and Fourier transform infrared spectra of the composite film indicated that Hb retained its native structure in the film. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa=?0.209 V and E_pc= ?0.302 V (vs. SCE) in pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. To the reduction of H₂O₂, the biosensor had a good linear range from 8.0×10^?7 to 1.8×10^?4 mol/L with a detection limit of 3.0×10^?7 mol/L. The apparent Michaelis‐Menten constant K^app_M was estimated to be 3.4×10^?5 mol/L.     

Cathodic Stripping Voltammetry of 2-Mercapto-5-Methyl-1,3,4-Thiadiazol and 2,5-Dimercapto-1,3,4-Thiadiazol at a Controlled-Growth Mercury Drop Electrode

2-Mercapto-5-methyl-1,3,4-thiadiazol (MMTD) and 2,5-dimercapto-1,3,4-thiadiazol (DMTD) were studied by differential pulse cathodic stripping voltammetry (DPCSV). The influence of buffer, pH, accumulation potential (E_acc), and accumulation time (t_acc) was investigated. It was stated that the concentration of the buffer affects the height of DPCSV peaks. The best analytical signals were recorded in acetate buffer at pH 4.3 and a buffer concentration of 0.01 mol/L for MMTD and 0.02 mol/L for DMTD, E_acc = 0.2 V, and t_acc = 120 s for MMTD and 180 s for DMTD. A linear dependence was found from 1 to 8 × 10^?8 mol/L for MMTD and from 1 × 10^?8 to 1 × 10^?7 mol/L for DMTD. The influence of cations [Cu(II), Co(II)] was also considered.     

Application of Polymer‐Modified Hanging Mercury Drop Electrode in the Indirect Determination of Certain β‐Lactam Antibiotics by Differential Pulse,Ion‐Exchange Voltammetry

A selective and sensitive polymer‐modified electrode was developed for β‐lactam antibiotics (cefaclor, amoxycillin and ampicillin) present in formulated and blood plasma samples for the quantitative analysis in aqueous environment. The detection was made using an ion‐exchange voltammetric technique, in differential pulse mode, on poly(N‐chloranil N,N,N′,N′‐tetramethylethylene diammonium dichloride)‐modified hanging mercury drop electrode of a three‐electrode system (PAR Model 303A) attached with a Polarographic Analyzer/Stripping Voltammeter (PAR Model 264A). Antibiotics, which are electroinactive compounds, were essentially converted to their electroactive oxazolone analogues through acid treatment under drastic conditions (0.1 mol L^?1 HCl, ～85 °C, 2 h). These analytes in the form of their respective oxazolones were indirectly analyzed by oxazolone entrapment in the polymeric film through ion‐exchange process at modified electrode surface (accumulation potential ?0.20 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.4, KH₂PO₄‐NaOH buffer (ionic strength 0.1 mol L^?1), scan rate 10 mV s^?1, pulse amplitude 25 mV). The limit of detection of cefaclor‐derived oxazolone was found to be 2.12 nmol L^?1 (0.82 ppb, S/N 3, RSD 3.21%) in terms of cefaclor (a representative β‐lactam) concentration.     

Imine Gels Based on Ferrocene and Porphyrin and Their Electrocatalytic Property

A series of porphyrin‐based imine gels have been synthesized via dynamic covalent gelation between 5,10,15,20‐tetra(4‐aminophenyl)‐21H,23H‐porphyrin (H₂TAPP) derivatives and various aldehyde compounds. The porphyrin‐ferrocene imine gels based on MTAPP (M=H₂, Ni²⁺, Co²⁺, Pd²⁺ and Zn²⁺) and ferrocene‐1,1′‐dicarbaldehyde (NA) display efficient HER, OER and ORR activities in alkaline media. Among the gels, CoTAPP‐NA shows an HER current density of 10 mA cm^?2 at low overpotential of 470 mV and small Tafel slope of 110 mV decade^?1 in alkaline media. CoTAPP‐NA also exhibits OER catalytic activity with low overpotential (416 mV for 10 mA cm^?2). CoTAPP‐NA shows ability in overall water splitting in alkaline media. In addition, CoTAPP‐NA exhibits onset potential (E_p) of 0.95 V and half‐wave potential (E_1/2) of 0.84 V in 1.0 mol L^?1 KOH solution for oxygen reduction. Moreover, the gel catalyst shows good stability.     

Electroanalytical method for determination of the pesticide dichlorvos using gold-disk microelectrodes

This paper reports the use of laboratory-prepared gold microelectrodes and square-wave voltammetry for analytical determination of low concentrations of the pesticide dichlorvos in pure and natural water samples. After optimization of the experimental and voltammetric conditions, the best voltammetric responses—current intensity and voltammetric profile—were obtained in 0.1 mol L^–1 NaClO₄ with f=100 s^–1, a=50 mV, and E_s=2 mV. The observed detection and quantification limits in pure water were 7.8 and 26.0 g L^–1, respectively. The reproducibility and repeatability of the method were also determined; the results were 1.4% (n=5) and 1.2% (n=10), respectively. Possible interfering effects were evaluated in natural water samples collected at different points with different levels of contamination from agricultural, domestic, or industrial waste from an urban stream. Results showed that the detection and quantification limits increased as a function of the quantity of organic matter present in the samples. Nonetheless, the values observed for these method characteristics were below the maximum value allowed by the Brazilian code for organophosphorus pesticides in water samples. Recovery curves constructed using the standard addition method were shown to be satisfactory compared with those obtained from high-performance liquid chromatography, confirming the suitability of the method for analysis of natural water samples. Finally, when the method was used to determine dichlorvos in spiked cows milk samples, satisfactory recovery and relative standard deviations were obtained.     

Determination of α‐Lipoic acid on a Pyrolytic Graphite Electrode Modified with Cobalt Phthalocyanine

In this work voltammetric techniques were explored for quantification of α‐Lipoic acid (ALA) using a pyrolytic graphite electrode modified with cobalt phthalocyanine. Cyclic voltammograms recorded in phosphate buffer solution containing 1×10^?3 mol L^?1 of ALA presented an oxidation peak located at +0.8 V vs. SCE. The modification of the electrode produced a 100 mV shift of the onset oxidation potential to less positive value and a substantial increase in the ALA oxidation current. Among the voltammetric techniques explored, differential pulse voltammetry showed the best performance for quantifications of the analyte in low concentrations. Limits of detection and quantification of ALA obtained corresponds to 3.4×10^?9 mol L^?1 and 1.2×10^?8 mol L^?1, respectively.     

Determination of allura red in some food samples by adsorptive stripping voltammetry

Square wave (SW) voltammetry was used to explore the adsorption properties of the food additive dye Allura Red on a hanging mercury drop electrode (HMDE). By using the adsorptive stripping voltammetric approach, we developed a sensitive electroanalytical method for the determination of this azo dye. A well-developed voltammetric peak probably related to the cathodic reduction of the azo moiety was obtained in pH 9 Britton-Robinson (B-R) buffer at 613 mV. Cyclic voltammetric studies indicated that the reduction process was irreversible and primarily controlled by adsorption. The adsorptive voltammetric signal was evaluated with respect to various experimental conditions; the optimized values were supporting electrolyte, B-R buffer; pH 11; accumulation time, 180 s; accumulation potential, 0.0 V; scan rate, 900 mV/s; pulse amplitude, 75 mV; and SW frequency, 90 Hz. Adsorptive voltammetric peak current showed a linear response for Allura Red in the concentration range of 2.5 x 10(-8) to 2.0 x 10(-7) mol/L (r = 0.998). The limit of detection was 8.5 x 10(-9) mol/L (4.2 ng/mL), the precision in terms of relative standard deviation was 1.3%, and the mean recovery was 102%. Possible interferences by several substances usually present in food products such as food additive azo dyes (E110, E102), gelatin, natural and artificial sweeteners, preservatives, and antioxidants were also evaluated. The proposed electrochemical procedure was successfully applied to the determination of this food dye in commercially available candy and a soft drink. The results were compared by statistical evaluation with those obtained by a reference spectrophotometric method.     

Voltammetric Behavior of Mifepristone (RU‐486) Using Square‐Wave and Adsortive Stripping‐Wave Techniques. Determination in Urine Samples

The behavior of Mifepristone (RU‐486) was studied by square‐wave technique, leading to two methods for its determination in aqueous samples and urine samples at pH 2. The application of the square‐wave (SW) without the adsorptive accumulation and stripping voltammetric (AdSV) show the maximum response at ?0.896 V using an accumulation potential of ?0.5 V. The effect of experimental parameters that affect this determination are discussed. For the stripping technique, Mifepristone proved to be more sensitive, yielding signals four times larger than those obtained by applying a square‐wave scan without the previous accumulation. The calibration plot to determine Mifepristone was linear in the range 2.4×10^?8 and 5.4×10^?7 M by stripping mode with an accumulation time t_acc of 30 s. The relative standard deviation obtained for concentration levels of Mifepristone as low as 2.0×10^?7 M with square‐wave was 1.17% (n=10) and with stripping square‐wave 2.02% (n=10) in the same day. The two proposed methods (SW and SWAdSV) were applied to the determination of Mifepristone in urine.     

Simultaneous voltammetric determination of carbendazim and carbaryl in medicinal plant infusions with a boron-doped diamond electrode

This study is aimed to develop an electroanalytical methodology using a boron-doped diamond electrode to determine simultaneously and selectively carbendazim (CBZ) and carbaryl (CAR). In previous studies using cyclic voltammetry oxidation, peaks were observed at 1.03 V (CBZ) and 1.44 V (CAR), with characteristics of an irreversible process controlled by diffusion of species, with a supporting electrolyte of BR buffer (0.1 mol L^?1) and pH adjusted to 6.0. The differences between the potentials for both pesticides, about 400 mV, indicate the possibility of selective determination of CBZ and CAR. The square-wave voltammetric parameters were optimised. The best separation conditions were pH 6.0, square-wave frequency of 100 s^?1, pulse amplitude of 50 mV and scan increment of 2.0 mV. These parameters were used to obtain the calibration curves of CBZ and CAR. An analytical curve was constructed in the range concentration of CBZ of 1.3 mg L^?1 to 15.3 mg L^?1 and CAR of 1.0 mg L^?1 to 11.4 mg L^?1, respectively. The limits of detection (LOD) and limits of quantification (LOQ) for CBZ were 0.40 mg L^?1 and 1.30 mg L^?1, respectively. For CAR, the LOD and LOQ were 0.30 mg L^?1 and 1.00 mg L^?1, respectively. Sensitivity values were 0.78 and 2.60 µA/mg L^?1 for CBZ and CAR, respectively. The electroanalytical method was applied in Mikania glomerata infusions. The recovery values were 106.2% and 116.5% for CBZ and CAR, respectively. The results show that the developed method is suitable for application in medicinal plant samples.