Determination of Copper,Nickel and Cadmium by Faas After Preconcentration with Zinc-Piperazinedithiocarbamate Loaded on Activated Carbon by Solid-Phase Extraction

ABSTRACT

A method was developed for the preconcentration of copper, nickel and cadmium in water samples, prior to their determination by FAAS, using the Zn-piperazinedithiocarbamate complex (ZnPDC) loaded on activated carbon. In this method, Cu, Ni and Cd in liquid phase quantitatively replaced zinc on a ZnPDC-activated carbon solid phase. Afterwards, the metals on the solid phase were easily eluted by Hg (II) solution into aqueous phase, and were measured by FAAS. The optimum experimental parameters such as pH, sample volume, and effect of matrix ions for the preconcentration of the metals were investigated. The range of linearity 0-6, 0-5, 0-3 μgml^?1, correlation coefficient 0.998, 0.996, 0.999, detection limits 15.7, 23.5, 11.8 ngml^?1 and determination limits 136, 179, 98 ngml^?1 in final Hg(II) solution were obtained for Cu, Ni and Cd, respectively. The proposed method has been employed for the determination of Cu, Ni and Cd in various standard metal alloys and natural water samples.     

2‐Aminocyclopentene‐1‐Dithiocarboxylic Acid‐Naphthalene Adsorbent for the Preconcentration and Determination of a Trace Copper in Real Samples by Spectrophotometric Method

A solid uncharged complex produced from 2‐aminocyclopentene‐1‐dithiocarboxylic acid (synthetic reagent) on naphthalene provides a very sensitive, selective and economical method for the preconcentration and determination of trace amounts of copper in drug and alloy samples. The 2‐aminocyclopentene‐1‐dithiocarboxylate of copper is retained quantitatively on microcrystalline naphthalene in the pH range 2.8–3.3. After filtration the solid mass consisting of copper complex‐naphthalene is dissolved with 4 mL of dimethylformamide (DMF). The absorbance is measured at 462 nm with a spectrophotometer against the reagent blank and molar absorptivity found to be 2.8 × 10⁵ liter mol^?1 cm^?1. Beer's law is obeyed over the concentration range of 0.1–16.0 μg of copper in 4 mL of the dimethylformamide solution. Detection limit is 3 ng mL^?1 [signal to noise ratio = 2]. Ten replicate determinations on a sample containing 1 μg of copper gave a relative standard deviation of 0.76%. The interference of a large number of anions and cations have been studied and the optimized conditions developed were utilized for determination of copper in various real samples.     

On-line preconcentration and determination of cobalt by chelating microcolumns and flow injection atomic spectrometry

A simple and sensitive flow injection analysis-atomic absorption spectrometric procedure is described for the determination of cobalt. The method is based upon on-line preconcentration of cobalt on a microcolumn of 2-nitroso-1-naphthol immobilized on surfactant coated alumina. The trapped cobalt is then eluted with ethanol (250 μl) and determined by flame atomic absorption spectrometry. The analytical figures of merit for the determination of cobalt are as follows: detection limit (3 S), 0.02 ng ml⁻¹; precision (RSD), 2.8% for 20 ng ml⁻¹ and 1.7% for 70 ng ml⁻¹ of cobalt; enrichment factor, 125 (using 25 ml of sample). The method has been applied to the determination of cobalt in water samples, vitamin B₁₂ and B-complex ampoules and accuracy was assessed through recovery experiment and independent analysis by furnace AAS.     

Non-extractive derivative spectrophotometric determination of cobalt in neutral micellar medium

A sensitive derivative spectrophotometric method using 1-nitroso-2-naphthol has been developed for determination of trace amounts of cobalt in the presence of a neutral surfactant. Photometric parameters, viz., lambda(max), molar absorption coefficient and analytical sensitivity of the complex formed in micellar media are 420 nm, 3.18x10(4) l mol(-1) cm(-1) and 2.05 ng ml(-1), respectively. Beer's law holds from 0.20 to 3.0 mug ml(-1) of the analyte concentration. The method has a high sensitivity with a detection limit of 1.68 ng ml(-1). A selective determination of cobalt in presence of copper(II) or iron(III) using derivative spectral profiles and without any masking or pre-separation is also reported. Samples of drugs and standard alloys analysed by the proposed method yielded results comparable to those obtained using recommended procedures.     

Ultraviolet absorption spectra of α-nitroso β-naphthol and its copper chelate

From a comparative study of the U.V. absorption spectra of α-nitroso-β-naphthol and of β-naphthol in neutral ethanol and in the presence of 0.1N HClO₄ and 0.1N KOH respectively, evidence in favour of the quinone-oxime structure of α-nitroso-β-naphthol has been presented. The spectrum of the copper chelate of α-nitroso-β-naphthol indicates a planar configuration of the complex with considerable resonance between the quinonoid and benzenoid structures of the ligand.     

Copper determination after FI on-line sorbent preconcentration using 1-nitroso-2-naphthol as a complexing reagent

The suitability of 1-nitroso-2-naphthol as a complexing agent for on-line preconcentration of copper using RP-C₁₈ material in a microcolumn with flow injection coupled with flame atomic absorption spectrometry (FI-FAAS) has been tested. Various parameters affecting complex formation, such as pH, sample flow rate, etc. and its elution into the nebulizer of FAAS were optimized. ¶A 5 × 10^–3 mol/L reagent was on-line mixed with aqueous sample solution acidified with 0.1% (v/v) nitric acid ¶(pH 3–4) and flowed through the microcolumn for 30 s. The adsorbed complexes in the microcolumn were eluted with ethanol in 10 s into the nebulizer of FAAS. A good precision (1.7% for 50 μg/L copper, n = 12), high enrichment factor (19) with detection limit (3σ) 2.0 μg/L, and sample throughput (90 h^–1) were obtained. The method was applied to certified reference materials seawater, mussel (biological), NBS-362 and NBS-364 (special low alloy steel), for the determination of copper, and the results were in good agreement with the certified values.     

Syringe-to-syringe-dispersive liquid–phase microextraction combined with flame atomic absorption spectrometry for pre-concentration and determination of cobalt with the aid of experimental design

A rapid and selective technique has been proposed for the extraction, pre-concentration and determination of trace amounts of cobalt in water and pharmaceutical samples by syringe-to-syringe-dispersive liquid–phase microextraction (SS-DLPME) combined with flame atomic absorption spectrometry (FAAS). In the developed method, 1-nitroso-2-naphthol was used as a selective complexing agent and 1-octanol was selected as the extraction solvent. Factors such as pH of the sample solution, concentration of the complexing agent, volume of the extraction solvent, number of injections and centrifugation time affecting the extraction efficiency were screened using a Plackett–Burman design (PBD) and optimised using a Box–Behnken design (BBD). Under optimum conditions, a dynamic linear range of 2.5–650 μg L^?1 with the coefficient of determination r² = 0.997 was obtained. The resultant limit of detection (LOD) was 0.68 μg L^?1, whereas the enrichment factor (EF), intraday precision and inter-day precision were 281, 1.43% and 1.93%, respectively. This method was used successfully for pre-concentration and determination of the analyte in environmental water and drug samples.     

The trace determination of some heavy metals in waters by flow-injection spectrophotometry and potentiometry

Three automated flow-injection systems are proposed for the determination of traces of manganese(II), lead and copper(II) in waters. The first system utilizes the catalytic effect of manganese(II) on the oxidation of N,N-diethylaniline by potassium periodate at pH 6.86–7.10 (30°C) and is used for spectrophotometric determination at 475 nm in the range 0.02–1.00 μg1^?1; the system involves reagent injection and stopped flow. The determination of lead in the range 0.7–100 μg1^?1 is based on spectrophotometric detection of the lead 4/(2-pyridylazo)resorcinol complex at 525 nm after on-line preconcentration of the sample (5–50 ml) on a minicolumn filled with Chelex-100 or Dowex 1-X8 resin. A potentiometric flow-injection system with a copper ion-selective electrode is applied for the determination of 0.5–1000 μg 1^?1 copper(II) after on-line preconcentration of 50–500 ml of sample on Chelex-100 resin. The procedures are tested on synthetic and real water samples, including sea water and waste-waters.     

Dosage du cobalt dans les aciers 188 base sur la formation du 60mco par activation aux neutrons thermiques

A method for the determination of cobalt in $\text{18}\text{8}$ steels, based on formation of ^60mCo is proposed. Most of the iron is extracted, then cobalt is extracted as its α-nitroso-β-naphthol complex into toluene. The losses are determined exactly. A determination is complete within 2 h with a precision of ±9% ; the limit of sensitivity is 2 μg of cobalt. The results obtained (average 350 p.p.m.) are compared with results obtained spectrophotometrically (average 368 p.p.m.).     

Indirect Determination of Trace Tetraborate by Differential Pulse Polarography Using Its Copper Complex and Application to Waste and Drinking Water

A new differential pulse polarographic (DPP) method has been developed for the trace determination of boron. Its most stable copper complex is used in 0.5 M KNO₃ electrolyte since boron is not electroactive. By continuous addition of tetraborate to copper solution, the copper peak decreased first but then the peak became very small and nearly constant. This point was used for the boron determination. It was found that one mole of copper used two moles of tetraborate. Using this relationship, 1×10^?5 M tetraborate could be determined. The quantification limit was 2.5×10^?6 M and detection limit was 8×10^?7 M. In the presence of complex forming ions such as Pb, Zn, and Cd, the borate found in sample was somewhat smaller because of their reaction with borate. But since their complexes were not as strong as copper, only a few percent of borate were used. No interference was observed in the presence of calcium, chloride and sulfate. This method is applied for the determination of B in borax ore, waste water of borax industries and tap water of Ankara city.     

The heterometric micro-analysis of cobalt with α-nitroso - β-naphthol. a general study.

1. The reaction between cobaltous or cobaltic and α-nitroso-β-naphthol was extensively studied heterometrically both in water and in alcoholic solutions. The influence of complexing agents and of the acidity on the precipitation of cobalt-α-nitroso-β-naphthol was investigated. In all cases the molar ratios : [Co] [αβ] at the end of the precipitation were established and the possible compounds which were obtained were discussed. 2. Micro-analytical heterometric methods are given for the determination of cobalt or α-nitroso-β-naphthol. The determination can be carried out with precision even in concentrations as low as 0.0001M Co. Conversely, very dilute alcoholic solutions of α-nitroso-β-naphthol may be titrated with precision with a dilute solution of cobalt nitrate. 0.2–0.5 mg cobalt in 20 ml solution are required for the analysis. The error lies between zero and 3%.     

Selective solid phase extraction and preconcentration of ultra-trace inorganic mercury in water samples using 2,6-dimethyl-morpholine dithiocarbamate

A sensitive and selective solid-phase spectrophotometric method for the determination of trace amounts of Hg(II) cation in water is described. A complex was created with Hg(II) using 2,6-dimethyl-morpholine dithiocarbamate (DMMDTC) to form Hg(II)–(DMMDTC) and this complex was adsorbed onto microcrystalline naphthalene (MN) and then eluted with 5% acetic acid (in ethanol) solution. A preconcentration factor of 187 and a recovery of 95% were observed at pH of 5.0 and for 10 min. of extraction. The separated Hg(II) ions were quantified by using ultraviolet-visible spectrophotometer at 490.0 nm by creating a colored complex with dithizone in Triton X-100 surfactant media. Molar absorptivity and sandell’s sensitivity for the Hg(II)-dithizone were determined as 4.96 × 10⁵ Lmol^?1cm^?1 and 0.4032 µg cm^?2, respectively. The detection limit (LOD) was 1.7 μg L^?1 under the optimized conditions of the analytical method.     

Subnanomolar Determination of Indium by Adsorptive Stripping Differential Pulse Voltammetry Using Factorial Design for Optimization

Abstract

A highly sensitive method to determine of indium is proposed by adsorption stripping differential pulse cathodic voltammetry (AdSDPCV) method. The complex of indium ions with xylenol orange is analyzed based on the adsorption collection onto a hanging mercury drop electrode (HMDE). After accumulation of the complex at ?0.20 V vs. Ag/AgCl reference electrode, the potential is scanned in a negative direction from ?0.40 to ?0.75 V with the differential pulse method. Then, the reduction peak current of In(III)–XO complex is measured. The influence of chemical and instrumental variables was studied by factorial design analysis. Under optimum conditions and accumulation time of 60 s, linear dynamic range was 0.1–10 ng/ml (8.7 × 10^?10 to 8.7 × 10^?8 M) with a limit of detection of 0.03 ng/ml (2.6 × 10^?10 M); at accumulation time of 5 min, linear dynamic range was 0.04–10 ng/ml (3.4 × 10^?10 to 8.7 × 10^?8 M) with a limit of detection of 0.013 ng/ml (1.1 × 10^?10 M). The applicability of the method to analysis of real samples was assessed by the determination of indium in water, alloy, and jarosite (zinc ore) samples.     

Determination of manganese by flame atomic absorption spectrometry after its adsorption onto naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN)

A system for determination of manganese, after preconcentration with 3% (w/w) 1-(2-pyridylazo)-2-naphthol (PAN), adsorbed on microcrystalline naphthalene is proposed. An amount of 200 mg of this complexing mixture is placed in a glass column and conditioned with a NH₄Cl/NH₄OH buffer solution (pH 9.5). The aqueous sample, containing manganese, is treated with an ammonium tartrate solution, then with a hydroxylammonium chloride solution and, finally, with a buffer solution. The resulting solution is passed through the column containing microcrystalline naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN) where Mn(II) is retained. The column is first washed with deionized water and then with 10.0 ml of dimethylformamide to dissolve the Mn(II)-PAN/naphthalene complex. Manganese is determined by air-acetylene flame atomic absorption spectrometry. About 1 μg of manganese can be concentrated from 200 ml of aqueous sample, allowing a preconcentration factor of 20, a limit of quantification of 5 ng ml⁻¹ and R.S.D. of 3.8%. The accuracy was ascertained using certified reference materials, including samples of urine and glass. Water samples were also analysed and the results are in good agreement with those obtained by graphite furnace atomic absorption spectrometry.     

Electrothermal atomic absorption spectrometric determination of cobalt in steel after chloroform extraction of its 1-nitroso-2-naphthol complex

Direct determination of μg g^-1 levels of cobalt in steels and corrosion products by electrothermal atomic absorption is difficult because of suppression of the cobalt signal by mineral acids and other metals. Extraction or cobalt with 1-nitroso-2-naphthol into chloroform in the presence of citrate overcomes this problem. Samples (0.4–10 mg) may be dissolved in a variety of acids, and a detection limit of 0.005 μg g^-1 in the chloroform extract is obtained.     

Determination of trace amounts of nickel by differential pulse adsorptive cathodic stripping voltammetry using calconcarboxylic acid as a chelating agent

A method for the determination of nickel(II) by stripping voltammetry is described. The method is based on the adsorptive accumulation of nickel(II) calconcarboxylic acid complex onto a hanging mercury drop electrode (HMDE), followed by the reduction of the adsorbed complex using differential pulse voltammetry. The optimum operating conditions and parameters were found to be 0.05 M NH₃/NH₄Cl buffer (pH = 9.5) as the supporting electrolyte, a ligand concentration of 1 × 10^?6 M, accumulation potential of ?0.5 V (vs. Ag/AgCl) and accumulation time of 60 s. At the optimized conditions, the peak current is proportional to the concentration of nickel in the range of 1.7 × 10^?9 to 4.7 × 10^?7 M (0.1–28 ng ml^?1) with a detection limit of 0.05 ng ml^?1. The relative standard deviation (n = 10) at nickel concentrations of 2, 10 and 15 ng ml^?1 varies in the range 0.76 to 2.1%. Possible interferences by metal ions, which are of great significance in real matrices, have been studied. The method was successfully applied to the determination of nickel content in a chocolate sample.     

Application of a macromolecular micellar system formed by the P123 triblock copolymer for determination of copper concentrations

This work proposes a method for determination Cu(II) concentrations, based on the formation of a copper-1-nitroso-2-naphthol complex, in the presence of micelles; formed by a triblock copolymer, made up of two blocks of polyethylene oxide (PEO), and one block of polypropylene oxide (PPO). The insoluble copper complexes, are concentrated inside the hydrophobic micelle core; formed by the PPO block. For a solution containing 0.200 mg L⁻¹ Cu(II), the proposed method had a relative standard deviation of 2.0% (n = 3); an absolute error from 0.11 to 0.39 mg L⁻¹; and a linear calibration range, from 0.200 to 0.800 mg L⁻¹. Detection and quantification limits, were 43.1 mg L⁻¹ and 144 mg L⁻¹, respectively. We show that there is excellent agreement, between the results obtained using our novel method; and those obtained using flame atomic absorption spectrometry: In the determination of Cu(II) concentrations, in Brazilian sugar-cane spirits. The proposed method, is the first to apply macromolecular micelle systems, to the determination of copper concentrations; and improves upon the results obtained using molecular surfactants. This method is environmentally friendly (since it does not use any organic solvents for extraction), and the triblock copolymer is biodegradable and non-toxic.      

Determination of Trace Amounts of Copper by Adsorptive Stripping Voltammetry

ABSTRACT

A technique is presented for the determination of trace amounts of copper(II) by adsorptive cathodic stripping voltammetry. The procedure is based on adsorptive accumulation of copper(II)-Alizarin Red S (ARS) complex on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of the reduction current of the adsorbed complex at -0.16 V (vs. Ag/AgCl). The height of the copper -ARS reduction peak is linearly dependent upon the copper(II) concentration between 0.2-15 and 15-500 ng.ml^?1. The detection limit of the technique is 0.05 ng.ml^?1 copper(II) for a collection time of 1 minute. The method is free from most interferences. The procedure has been successfully applied to the determination of trace amounts of copper(II) in some analytical grade salts.     

Determination of Some Heavy Metal Ions with a Carbon Paste Electrode Modified by Poly(glycidylmethacrylate‐methylmethacrylate‐divinylbenzene) Microspheres Functionalized by 2‐Aminothiazole

A carbon paste electrode modified with 2‐aminothiazole functionalized poly(glycidylmethacrylate‐methylmethacrylate‐divinylbenzene) microspheres was used for trace determination of mercury, copper and lead ions. After the open‐circuit accumulation of the heavy metal ions onto the electrode, the sensitive anodic stripping peaks were obtained by square wave anodic stripping voltammetry (SWASV)). Many parameters such as the composition of the paste, pH, preconcentration time, effective potential scan rate and stirring rate influence the response of the measurement. The procedures were optimized for most sensitive and reliable determinations of the desired species. For a 10‐min preconcentration time in synthetic solutions at optimum instrumental and experimental conditions, the detection limit (LOD) was 12.3, 2.8 and 4.5 μg L^?1 for mercury, copper and lead, respectively. The limits of detection may be enhanced by increasing the preconcentration time. For example, LOD of mercury and copper was 4.9 and 1.0 μg L^?1 for fifteen minutes preconcentration time. The sensitivity may also considered to be increased by using a more suitable electrode composition targeting the more conductive electrode with lesser amount of modified polymer for sub‐μg L^?1 levels of heavy metal ions. The optimized method was successfully applied to the determination of copper in tap water and waste water samples by means of standard addition procedure. The copper content found was comparable with the certified concentration of the waste water sample. The calibration plots for mercury and lead spiked real samples were also drawn.     

Indirect determination of vanadium by atomic absorption spectrometry

An indirect method for the determination of vanadium as vanadate by atomic absorption spectrometry is described. In neutral medium, vanadate forms a stable ion-association complex with copper (II) and biguanide, which is extractable into butanol with an efficiency higher than 99%. The copper content in the extract (and hence indirectly VO^?₃) is determined by aspirating it directly into an acetylene flame. The calibration graph is linear up to 3.4 μg ml^?1 of VO^?₃. The limit of detection is 16 ng ml^?1. Only chromium interferes.