Direct Electrochemical Oxidation of NADPH at a Low Potential on the Carbon Nanotube Modified Glassy Carbon Electrode

Introduction Because of its novel structural and electronic proper-ties, high chemical stability, and extremely high me-chanical strength and modulus,1 carbon nanotube (CNT), which has become a major subject of many experimen-tal and theoretical investigations, has a wide potential application from structural materials to nanoelectronic components2-12 since its initial discovery by Iijima13 in 1991 and the subsequent report about the synthesis of large quantities of CNT by Ebbesen and cowork…     

The Electrochemical Behavior and the Determination of Bavistin on Glassy Carbon Electrode

Bavistin(MBC)'isatypeofveryimportantbactericides.Theanalyticalmethodsofthispesticideincludingchromatography',polarography'havebeenreported,butthereisnoreportaboutthedetendnationwithvoltanuntryonglassycarbonelectrode.Inthispaper,westudiedthevoltanunetric(CV)propertiesandthedifferentialpulsestrippingvoltanunetry(DPSV)detendnationofMBConglassycarbonelectrode.TheinstrUmentusedinthisexperimentwastheBAS-l(X)AElectroanalyser.Aglassycarbonelectrodewasusedastheworkingelectrode,aconunercialAgjA…     

Voltammetric Determination of L‐Dopa Using a Carbon Nanotubes‐Nafion Modified Glassy Carbon Electrode

Abstract

A method for determination of L‐dopa by the adsorption stripping voltammetry (ASV) using a multiwalled carbon nanotubes (MWNTs)–Nafion modified glassy carbon electrode (GMGCE) was proposed. This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed and the anodic peak potential is ca. 0.374V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of L‐dopa in samples. There is a good linear relationship between the peak current (i_p) and L‐dopa concentration in the range of 3.5×10^?7～1.5×10^?5 mol/L, with the limit of detection 5.0×10^?8 mol/L.     

Electrochemical Behavior of Hydrogen Peroxide at a Glassy Carbon Electrode Modified with Nickel Hydroxide–Decorated Multiwalled Carbon Nanotubes

Abstract

The multiwalled carbon nanotube–nickel hydroxide composite film used to modify glassy carbon electrode was prepared and confirmed by transmission electron microscopy and cyclic voltammetry. The process and mechanism of film formation were discussed in detail. The electrode modified with the composite film exhibited good catalytic activity toward electrochemical oxidation of hydrogen peroxide in 0.1 mol/L sodium hydroxide solution. Various factors affecting the electrocatalytic activity of nickel hydroxide film were investigated. The anodic peak current increased with the increased concentration of hydrogen peroxide. The linear range for the determination of hydrogen peroxide was from 1.5 × 10^?6 mol/L to 2.5 × 10^?3 mol/L with the detection limit 6.1 × 10^?7 mol/L (S/N = 3). And the proposed method was applied to the determination of hydrogen peroxide in disinfector with higher sensitivity and lower detection limit.     

Anodic Oxidation of α‐Lipoic Acid at a Glassy Carbon Electrode and Its Determination in Dietary Supplements

Abstract

Direct electrochemistry of alpha‐lipoic acid (ALA) was performed at a glassy carbon electrode using cyclic, differential pulse and square wave voltammetry over a wide range of pH. The oxidation of ALA is an irreversible process, pH independent, and involves the charge transfer of one electron. The diffusion coefficient of ALA was calculated from the results obtained at pH 6.9 in 0.1 M phosphate buffer and was shown to be D ₀=1.1×10^?5 cm² s^?1. The limits of detection (LOD) and quantification (LOQ) calculated from the results obtained at this pH are 1.8 and 6.1 µM, respectively.

The lipoic acid content in two dietary supplements samples, a syrup containing ALA and capsules of ALA, has been determined directly at the glassy carbon electrode by differential pulse voltammetry using the standard addition method.     

Electrochemical Analysis of Mercury Using a Kryptofix Carbon‐Paste Electrode

Abstract

Successful applications of different analytical procedures to determine quantitatively mercury in aqueous media can be found in recent literature. Fundamentally it has made use of Cold Vapour Atomic Absorption Spectrometry (CV‐AAS), X‐Ray Fluorescence or UV Spectrophotometry, Inductively Coupled Plasma Atomic Emission Spectrometry (ICP‐AES), or Inductively Coupled Plasma Mass Spectrometry (ICP‐MS), which are the techniques commonly used for trace measurement of heavy metal in the laboratory. In this paper a new and alternative methodology to determine quantitatively mercury in aqueous media is reported. A kryptofix carbon‐paste electrode has been used to determine voltammetrically mercury. The detection limit for mercury was evaluated to be 0.12 µg/l.     

The Electrochemical Behavior of Neurotransmitters at a Poly (Pyrrole‐ β‐Cyclodextrin) Modified Glassy Carbon Electrode

Abstract

A glassy carbon electrode surface was modified with an electropolymerized film made of pyrrole and β‐cyclodextrin 1∶1, in a 0.1 M LiClO₄ solution using cyclic voltammetry. The resulting modified electrode (Ppy/β‐CD) exhibits interesting electrocatalytic activity toward the electrochemical oxidation of neurotransmitters such as dopamine (DA) and norepinephrine (NE). Well‐resolved and reversible cyclic voltammograms (CVs) were obtained for these organic compounds in a 0.1 M H₂SO₄ solution. The effect of the pH on the voltammetric response of DA and NE was also investigated inside the range of pH 2.8–8.4. The oxidation current of norepinephrine increase linearly with the concentration inside the range of 4×10^?7 M–2×10^?6 M. The oxidation current of dopamine also followed the same trend range of 2×10^?6 M–10^?5 M. The detection limit was 6×10^?6 M for (DA) and 8×10^?7 M for (NE). As an example, the relative standard deviation for 1×10^?5 M of DA was 2.056%. The diffusion coefficients D for the molecules studied were determined by means of the measurement of the effect of the scan rate on the CVs of the neurotransmitters. All the results showed that the electron transfer was predominantly diffusion controlled at the conducting polymer/solution interface.

Interference phenomenon due to ascorbic acid (AA) toward the neurotransmitters was also investigated. The novel modified electrodes presented capability to resolve perfectly the AA and neurotransmitters oxidation peaks. This performance could be achieved even at a concentration 20 times higher than the neurotransmitters.

Finally, the newly fabricated Ppy/β‐CD film exhibits interesting analytical performances compared with other systems in the literature, such as higher sensitivity, rapid response, good mechanical stability and reproducibility.     

Electrochemical Oxidation of Hydrazines at a 4-Pyridyl Hydroquinone Modified Electrode

ＥｌｅｃｔｒｏｃｈｅｍｉｃａｌＯｘｉｄａｔｉｏｎｏｆＨｙｄｒａｚｉｎｅｓａｔａ４－ＰｙｒｉｄｙｌＨｙｄｒｏｑｕｉｎｏｎｅＭｏｄｉｆｉｅｄＥｌｅｃｔｒｏｄｅＮＩＵＬｉ,ＹＯＵＴｉａｎ－ｙａｎ,ＪｏｈｎＹ．Ｇｕｉ,ＤＯＮＧＳｈａｏ－ｊｕｎ,ＷＡＮＧＥｒ－...     

Electrochemical Determination of Uric Acid Using a Multiwalled Carbon Nanotube Platinum–Nickel Alloy Glassy Carbon Electrode

Platinum–nickel nanoparticles were synthesized by a reduction procedure. The Pt–Ni/C composite was characterized by X-ray diffraction, infrared spectroscopy, transmission electron microscopy, and electrochemical analysis. The measurements show that the Pt–Ni/multiwalled carbon nanotubes provided higher electrocatalytic activity for the oxidation of uric acid than Pt–Ni/carbon black. The sensor prepared from the characterized material provided a long linear dynamic range from 0.1 to 240.4?µM with a detection limit of 0.03?µM and a sensitivity of 41.21?µA?mM^?1?cm^?2. The reported modified electrode also provided excellent selectivity, good stability, and satisfactory reproducibility for the determination of uric acid.     

Nafion‐Modified Glassy Carbon Electrode for Trace Determination of Indium

Abstract

A new method for determination of trace indium is proposed by the adsorption stripping voltammetry (ASV) using a Nafion‐modified glassy carbon electrode (NMGCE). This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed, and the anodic peak potential is ca. ?0.548 V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of indium in water samples. There is a good linear relationship between the peak current (i_p) and indium(III) concentration in the range of 1.0×10^?9–1.0×10^?7 mol/l, and the limit of detection is 7.5×10^?10 mol/l.     

The Electro‐Oxidation of Formaldehyde at a Boron‐Doped Diamond Electrode

Abstract

The characteristics of the boron‐doped diamond (BDD) electrode in this work were studied by atomic force microscope (AFM), scanning electron microscopy, and Raman spectroscopy. The electro‐oxidation of formaldehyde at the BDD electrode in 0.5 M K₂SO₄ with different pH was studied by cyclic voltammetry and amperometry. There is no significant oxidation peak of formaldehyde in acidic solution because the oxidation of formaldehyde is at the potential range of water discharge. However, in neutral solution, there is a well‐defined oxidation peak at about +2.2 V vs. Ag/AgCl. The relation between the response current and formaldehyde concentration is linear behavior at the concentration range from 50 to 600 µM. Besides, in neutral solution, the oxidation of formaldehyde is dominated by indirect oxidation at lower formaldehyde concentration, and it is dominated by direct oxidation at higher concentration. Finally, in alkaline solution, the oxidation of formaldehyde is dominated by indirect oxidation caused by a powerful oxidant and is related to the ratio of the amounts of formaldehyde and OH molecules at the BDD electrode surface.     

Electrocatalytic Oxidation of Dopamine by Ferrocene in Lipid Film Cast on a Glassy Carbon Electrode

ＩｎｔｒｏｄｕｃｔｉｏｎＤＡｉｓｏｎｅｏｆｅｓｓｅｎｔｉａｌｐａｒｔｉｃｉｐａｎｔｓｉｎｔｈｅｎｅｕｒｏ ｔｒａｎｓｍｉｓｓｉｏｎｐｒｏｃｅｓｓｉｎｍａｍｍａｌｉａｎｃｅｎｔｒａｌｎｅｒｖｏｕｓｓｙｓ ｔｅｍ .ＡｌｏｓｓｏｆＤＡ ｃｏｎｔａｉｎｉｎｇｎｅｕｒｏｎｓｍａｙｒｅｓｕｌｔｉｎｓｏｍｅｓｅｒｉｏｕｓｄｉｓｅａｓｅｓｕｃｈａｓＰａｒｋｉｎｓｏｎｉｓｍ .1Ｓｉｎｃｅｉｔｓｄｉｓｃｏｖ ｅｒｙｉｎｔｈｅ 195 0ｓ ,ＤＡｈａｓｂｅｅｎｏｆｉｎｔｅｒｅｓｔｔｏｎｅｕｒｏｓｃｉｅｎ ｔｉｓｔｓａｎｄｃｈｅｍ…     

Sensitive Determination of Clomipramine at Poly‐ABSA/Pt Nano‐Clusters Modified Glassy Carbon Electrode

Abstract

Clomipramine, an important tricylic antidepressant drug with low redox activity, was effectively electrocatalyzed on poly‐aminobenzene sulfonic acid/Pt nano‐clusters modified glassy carbon electrode (i.e., poly‐ABSA/Pt/GCE) and generated a sensitive anodic peak at about 0.80 V in pH 8.1 PBS. ABSA was electropolymerized on the surface of GCE modified with Pt nano‐clusters. Pt nanoparticles provide a 3 D and conductive structure for the polymer immobilization. The resulting sensor exhibited a considerable enhancement in voltammetric response characteristics: extending the linear range and lowering the detection limit. The anodic peak current of clomipramine was linear with its concentration over two concentration intervals, viz., 1.0×10^?7～4.0×10^?6 M and 4.0×10^?6～4.0×10^?5 M, with the detection limit of 1.0×10^?9 M (S/N=3). This method was successfully applied to the determination of clomipramine in drug tablets and proved to be reliable compared with UV.     

Voltammetric Determination of Dopamine in Human Serum and Urine at a Glassy Carbon Electrode Modified by Cysteic Acid Based on Electrochemical Oxidation of L ‐cysteine

Abstract

The voltammetric behavior of dopamine was studied at a glassy carbon electrode modified by cysteic acid, based on electrochemical oxidation of L ‐cysteine. The modified electrode showed strong electrocatalytic activity towards dopamine and good selectivity. In a phosphate buffer solution (pH 7.4), the anodic peak current obtain from the differential pulse voltammetry of dopamine was linearly dependent on its concentration in the range of 5×10^?9 to 4.0×10^?6mol · L^?1, with a detection limit of 2×10^?9mol · L^?1. The low‐cost modified electrode had been applied to the determination of dopamine in human serum and urine samples with satisfactory results.     

Direct Electrochemical Oxidation of Dihydronicotiamide AdenineDinucleotide （NADH） at An Ordered Carbon Nanotubes Electrode

With novel structure, extraordinary electronic properties, high chemical stability and extremely high mechanical strength1, carbon nanotubes (CNTs) have found a wide range of potential applications2-6. The subtle electronic properties suggest that CNTs have the ability to promote electron transfer when they are used as an electrode. The disordered CNTs have been used to fabricate electrode7-10. Thus, it is very interesting to fabricate the electrode using the ordered CNTs and to examin…     

Discrimination of Tea by the Electrochemical Determination of its Antioxidant Properties by a Polyaniline – DNA – Polyphenazine Dye Modified Glassy Carbon Electrode

Abstract

Voltammetric sensors have been developed on the bases of polyaniline and polymeric forms of methylene blue, methylene green, and neutral red obtained by multiple cycling of the potential. The integrity of the layers and expansion of the pH range of redox activity have been achieved by intermediate adsorption of native DNA that stabilized the oxidized polyaniline form. The formation of the coating layer was confirmed by electrochemical impedance spectroscopy and scanning electron microscopy. Model oxidants (ascorbic acid, hydroquinone, and quercetin) in the concentration range from 1?×?10^?6 to 1?×?10^?3 mol L^?1 influenced the measured redox peaks of polymeric dyes with standard deviations from 2.4 to 5.5%. The peak currents were used for classification of tea brands using principal component analysis and linear discrimination analysis. The average discrimination of the tea brands purchased on local market was approximately 100%. The assessment of antioxidant properties of tea infusions was in agreement with results obtained using a coulometric bromine titration.     

The Determination of Salbutamol Sulfat Based on a Flow‐Injection Coupling Irreversible Biamperometry at Poly(aminosulfonic acid)‐Modified Glassy Carbon Electrode

Abstract

The present work describes the development of a simple and efficient method for electrochemical analysis determination of SBS using polymer film coated modified electrode. A glassy carbon electrode (GCE) is successfully modified with electropolymerized film of aminosulfonic acid (ASA) in pH 6.8 phosphate buffer solution (PBS). Cyclic voltammetry (CV) were used to study the electrochemical properties of the polymer film and the appropriate condition for electropolymerization process. The voltammetric behavior of SBS at the PASA GC CMEs has been investigated, the results suggest that the PASA GC CMEs have good effect of electrocatalytic oxidation action to SBS, also propose the mechanism toward SBS. The flow‐injection irreversible biamperometry analysis method was studied under the applied potential difference of 0 V to determinate SBS. In 0.1 mol l^?1 (pH 6.80) phosphate buffer solution, a sensitive and irreversible oxidation peak was obtained at the PASA GC CMEs. Under the optimum conditions, SBS can be determined from the range 2.0×10^?6 to 1.0×10^?3 mol · 1^?1 with the sampling frequency of 100 samples per hour. The detection limit for SBS is 6.5×10^?7 mol l^?1 and the RSD for 20 replicate determinations of 4.0×10^?5 mol l^?1 SBS is 1.85%. The method is simple, with high selective rapid and sensitive. The method is applied to the determination of SBS in the drug with satisfactory results. Moreover, the physiologically common interferents (i.e., sucrose, lactose, citric acid, and citrate) negligibly affected the response of SBS. The PASA GC CMEs film‐coated electrode exhibited a stable and sensitive response to salbutamol sulfat in the presence of electrocatalysis oxidation.     

Direct Electrochemistry of Catalase on Single Wall Carbon Nanotubes Modified Glassy Carbon Electrode

Direct electrochemistry of catalase (Ct) has been studied on single wall carbon nanotubes (SWNTs) modified glassy carbon (GC) electrode. A pair of well-defined nearly reversible redox peaks is given at -0.48 V (vs. SCE) in 0.1 mol/L phosphate solution (pH 7.0).The peak current in cyclic voltammogram is proportional to the scan rate. The peak potential of catalase is shifted to more negative value when the pH increases. Catalase can adsorb on the SWNTs modified electrode.     

Electrochemical Characterization of CoHP–Si Incorporated into a Carbon Paste Electrode

Reduction of dioxygen at a carbon paste electrode (CPE) modified with cobalt hematoporphyrin complex immobilized on silica gel (CoHP–Si) was studied by cyclic voltammetry and rotating disk electrode. In 0.5molL^–1 KCl solution, the supported complex showed significant catalytic activity towards four-electron reduction of O₂ to H₂O at a relatively high pH (5.4). The reduction of dioxygen proceeds at a more negative potential (–0.375V) than the redox reaction Co^III/Co^II (0.464V), indicating that the mechanism does not involve the complex as an electron transfer mediator. Catalytic activity of CoHP–Si towards reduction of H₂O₂ was tested, but no activity was observed.Received October 26, 2002; accepted March 10, 2003 Published online July 16, 2003     

Gold Nanoparticle-based Layer-by-Layer Enhancement of DNA Hybridization Electrochemical Signal at Carbon Nanotube Modified Carbon Paste Electrode

Nanoporous materials have been widely applied to biosensor investigation. Recently, Guo et al. have investigated the mesoporous materials modified carbon paste electrode for rapid cTnI (cardiac troponin I) detection with enhanced sensitivity1-3. However, …