Determination of Magnesium Ascorbyl Phosphate in Cosmetic Bleaching Products Using a Disposable Screen-Printed Carbon Electrode

A preanodized screen-printed carbon electrode is used for the determination of magnesium ascorbyl phosphate in cosmetic bleaching products. The preanodization process exhibits a marked enhancement of the current response of magnesium ascorbyl phosphate at the screen-printed carbon electrode. The linear range is up to 240 (correlation coefficient = 0.999) in pH 2.0 citrate buffer with a detection limit (S/N = 3) of 0.33 μM. The electrode has the advantages of low cost and easy of handling and can be either disposable or reused since the renewal gives a good reproducible surface. Quantitative analysis was performed by the standard addition method for magnesium ascorbyl phosphate content in cosmetic products.     

肾上腺素在多壁碳纳米管修饰金电极上的电化学行为及测定

报道了一种测定肾上腺素的化学修饰电极和电化学分析方法。与裸金电极相比,刚果红改性的多壁碳纳米管修饰金电极可显著提高肾上腺素的氧化峰电流。实验优化了底液、pH值、修饰剂量、富集电位和富集时间等条件,建立了一种直接测定肾上腺素的高灵敏的电化学分析方法。该方法测定肾上腺素的线性范围为4.0×10-7~2.0×10-4mol.L-1;富集30 s后的检出限为8.5×10-8mol.L-1;对2.0×10-5mol.L-1的肾上腺素平行测定10次的相对标准偏差为4.9%。此方法已成功用于盐酸肾上腺素注射液中含量的测定。     

氨甲蝶呤在Co/GC离子注入修饰电极上电化学行为及其应用研究

氨甲蝶呤在0.1mol/LHAc-NaAc(pH=4.96)缓冲溶液中,用Co/GC离子注入修饰电极进行伏安测定,得到一良好的还原峰,峰电位为-0.95V(vs.SCE).峰电流Ip与氨甲蝶呤的浓度在2.2×10^-7～8.8×10^-6mol/L范围内呈线性关系。检出限为1.1×10^-8mol/L.建立了测定氨甲蝶呤的新方法,可用于实际样品的测定,回收率在98.9%～106.2%之间。用线性扫描和循环伏安法研究了体系的电化学行为及电极反应机理。实验表明,氨甲蝶呤的还原为不可逆吸附过程,并伴随两个电子和两个氢离子参与电极反应。用俄歇电子能谱(AES)和X射线光电子能谱(XPS)等表面分析技术对Co离子注入修饰电极的表面元素组成及深度分布等进行测定,表明Co离子确被注入到玻碳表面。扫速对催化效率的影响实验证明体系存在催化作用。     

聚乙烯吡咯烷酮修饰碳糊电极上酪氨酸的电化学研究及其测定

研究了酪氨酸在聚乙烯吡咯烷酮修饰碳糊电极的伏安行为,优化了测定条件,在此基础上建立了一种直接测定酪氨酸的电分析方法。氧化峰电流与酪氨酸的浓度在2×10-7～5×10-5mol·L-1之间有良好的线性关系,开路富集3min,检出限为1×10-7mol·L-1。用此方法测定了酒样和人尿中酪氨酸的含量,结果满意。     

Sensitive Electrochemical Determination of Trifluralin at a Disposable Pencil Graphite Electrode

A sensitive differential pulse (DP) voltammetric method has been proposed for the determination of trifluralin (TFA) based on both its reduction and oxidation at a disposable pencil graphite electrode (PGE). DP voltammograms recorded under optimized conditions show that oxidation and reduction peak currents increased linearly in the range from 1.0 to 75.0 μM and from 0.50 to 100.0 μM TFA, respectively. LOD and sensitivity values have been determined as 0.39 μM and 11170 μA mM⁻¹ cm⁻² for oxidation and as 0.20 μM and 22167 μA mM⁻¹ cm⁻² for reduction. The acceptable recovery values (95.2–104.8 %) were obtained from real water samples.     

丝网印刷电极在食品安全检测中的应用进展

食品安全问题一直以来都是被广泛关注的热点,选择成本低、使用方便、灵敏度高的检测手段也就成为了食品安全检测领域中研究的焦点。丝网印刷电极因具有可批量生产、成本低、灵敏度高和一次性可抛等特点,已被广泛应用到食品安全检测中。因此,近年来,关于丝网印刷电极在食品安全检测中的应用研究日益增多,建立了多种类型的电化学传感器。依据电化学传感器的不同类型,综述了丝网印刷电极在食品安全检测中的应用,并对丝网印刷电极的应用前景进行了展望。     

Electrochemical Investigations of the Anticancer Drug Idarubicin Using Multiwalled Carbon Nanotubes Modified Glassy Carbon and Pyrolytic Graphite Electrodes

The effect of surface modifications on the electrochemical behavior of the anticancer drug idarubicin was studied at multiwalled carbon nanotubes modified glassy carbon and edge plane pyrolytic graphite electrodes. The surface morphology of the modified electrodes was characterized by scanning electron microscopy. The modified electrodes were constructed for the determination of idarubicin using adsorptive stripping differential pulse voltammetry. The experimental parameters such as supporting electrolyte, pH, accumulation time and potential, amount of carbon nanotubes for the sensitive assay of idarubicin were studied as details. Under the optimized conditions, idarubicin gave a linear response in the range 9.36×10^?8–1.87×10^?6 M for modified glassy carbon and 9.36×10^?8–9.36×10^?7 M for modified edge plane pyrolytic graphite electrodes. The detection limits were found as 1.87×10^?8 M and 3.75×10^?8 M based on modified glassy carbon and edge plane pyrolytic graphite electrodes, respectively. Interfering species such as ascorbic acid, dopamine, and aspirin showed no interference with the selective determination of idarubicin. The analyzing method was fully validated and successfully applied for the determination of idarubicin in its pharmaceutical dosage form. The possible oxidation mechanism of idarubicin was also discussed. The results revealed that the modified electrodes showed an obvious electrocatalytic activity toward the oxidation of idarubicin by a remarkable enhancement in the current response compared with bare electrodes.     

Voltammetric Determination of Uric Acid with a Glassy Carbon Electrode Coated by Paste of Multiwalled Carbon Nanotubes and Ionic Liquid

The voltammetric behavior of uric acid (UA) has been studied at a multiwalled carbon nanotube‐ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆) paste coated glassy carbon electrode (MWNTs‐BMIMPF₆/GC). It is found that UA can effectively accumulate at this electrode and cause a sensitive anodic peak at about 0.49 V (vs. SCE) in pH 4.0 phosphate buffer solutions. Experimental parameters influencing the response of the electrode, such as solution pH and accumulation time, are optimized for uric acid determination. Under the optimum conditions, the anodic peak current is linear to UA concentration in the range of 1.0×10^?8 M to 1.0×10^?6 M and 2.0×10^?6 M to 2.0×10^?5 M. The detection limit is 5.0×10^?9 M for 180 s accumulation on open circuit. The electrode can be regenerated by successively cycling in a blank solution for about 3 min and exhibits good reproducibility. A 1.0×10^?6 M UA solution is measured for eight times using the same electrode regenerated after every determination, and the relative standard deviation (RSD) of the peak current is 3.2%. As for different electrodes fabricated by the same way the RSD (i.e., the electrode to electrode deviation) is 4.2%(n=9). This method has been applied to the determination of UA in human urine samples, and the recoveries are 99%–100.6%. In addition, comparison is made between MWNTs‐BMIMPF₆/GC and MWNTs/GC. Results show that the MWNTs‐BMIMPF₆/GC exhibits higher sensitivity, selectivity and ratio of peak current to background current.     

Use of Mercury Film Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotubes in Electrochemical Analysis of DNA

Mercury film plated on a glassy carbon electrode modified with multiwalled carbon nanotubes (MF/MWNTs/GCE) was used for the analysis of single (ss) and double stranded (ds) DNA, as well as for Jurkat genomic DNAs methylated to different degrees. The results indicated that the DNA molecules adsorbed quite strongly on the MF/MWNTs/GCE surface allowing ex situ adsorption and produce well developed peaks (due to cytosine and adenine) by using adsorptive stripping (Ads, ex situ) square wave voltammetry (SWV). Also, SWV of Jurkat DNA mixtures methylated to different degrees revealed a linear decrease of the peak height with increasing methylation indicating an increase of structural rigidity.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.     

Disposable Immunosensor for Escherichia Coli O157:H7 Based on a Multi-Walled Carbon Nanotube-Sodium Alginate Nanocomposite Film Modified Screen-Printed Carbon Electrode

A disposable immunosensor for the detection of Escherichia coli O157:H7 based on a multiwalled carbon nanotube–sodium alginate nanocomposite film was constructed. The nanocomposite was placed on a screen-printed carbon electrode, and horseradish peroxidase-labeled antibodies were immobilized to E. coli O157:H7 on the modified electrode to construct the immunosensor. The modification procedure was characterized by atomic force microscopy and cyclic voltammetry. Under optimal conditions, the proposed immunosensor exhibited good electrochemical sensitivity to E. coli O157:H7 in a concentration range of 10³–10¹⁰ cfu/mL, with a relatively low detection limit of 2.94 × 10² cfu/mL (S/N = 3). This immunosensor exhibited satisfactory specificity, reproducibility, stability, and accuracy, making it a potential alternative tool for early assessment of E. coli O157:H7.     

Application of Glassy Carbon Electrode Modified with a Bilayer of Multiwalled Carbon Nanotube and Polypyrrole Doped with Nitrazine Yellow for Voltammetric Determination of Naltrexone

A new sensitive electrochemical sensor was fabricated based on a layer by layer process. In this process the glassy carbon electrode (GCE) is first coated by a thin film of multiwalled carbon nanotubes (MWCNTs). In the next step, the electropolymerization of pyrrole in the presence of Nitrazine Yellow (NY) as a dopant anion is performed on the surface of the MWCNTs precoated electrode. The electrochemical response characteristics of the modified electrode toward naltrexone (NTX) were studied by means of linear sweep voltammetry (LSV). A remarkable increase (～19 times) was observed in the anodic peak current of NTX on the surface of the modified electrode relative to the bare GCE. The effects of experimental parameters on the electrode response such as, drop size of the cast MWCNTs suspension, pH of the supporting electrolyte, accumulation conditions and the number of cycles in the electropolymerization process were investigated. Under the optimum conditions, the modified electrode showed a wide linear response to the concentration of NTX in the range of 4.0×10^?8–1×10^?5 mol L^?1 with a detection limit of 12 nmol L^?1. The prepared sensor exhibited high sensitivity, stability and good reproducibility for the determination of NTX. This sensor was successfully applied for the accurate determination of trace amounts of NTX in pharmaceutical and clinical preparations.     

维生素C在多壁碳纳米管/壳聚糖复合膜修饰玻碳电极上的电化学行为及测定

研究了维生素C在多壁碳纳米管/壳聚糖复合膜修饰玻碳电极上的电化学行为及测定。实验结果表明,在0.2 mol/L PBS(pH6.0)缓冲溶液中,修饰电极对抗坏血酸的氧化具有明显的催化和增敏效应,其氧化峰电位由 0.5 V负移至 0.1 V(vs.AgCl/Ag)。对修饰剂碳纳米管的用量、支持电解质、富集电位和富集时间等进行了优化。采用半微分伏安法进行定量测定,其线性范围为4.0×10-6~2.0×10-3mol/L,r=-0.998 3,检出限为1.0μmol/L。对抗坏血酸在修饰电极上的电化学行为进行了探讨,其电极反应为具有吸附特性和不可逆的电极过程,测得参加反应的质子数为2,电极反应的电子转移系数为0.59。测定了维生素C药片中抗坏血酸的含量,回收率在93%~105%。     

用于DNA杂交检测的丝网印刷型生物传感器的研究

将单链DNA(ssDNA)固定到丝网印刷碳电极上构成电化学DNA传感器,采用电化学指示剂,建立DNA杂交的检测方法.Co(phen)33+电化学指示剂通过钴盐与配体邻菲罗啉络合制备,采用等离子发射光谱法(ICP-AES)和核磁共振法(NMR)表征功能基团,采用循环伏安法(CV)分析指示剂的电化学特性,并以此为基础研究ssDNA在电极表面的固定及DNA杂交过程.本研究探讨了直接吸附、静电吸附与键合等3种ssD-NA在电极表面的固定方法,结果表明,静电吸附法和键合法具有较高的ssDNA固定量,采用静电吸附法固定探针的电极杂交目标DNA后,Co(phen)33+易于嵌入双链DNA (dsDNA)中,CV峰电流(ip)信号随目标DNA浓度增加.本研究采用静电吸附ssDNA的电极检测DNA杂交,实验表明,当探针固定液中ssDNA浓度为5 mg/L时,目标DNA浓度在6.65×10- 8～4.26× 10-6mol/L范围内,Co(phen)33+在dsDNA修饰电极上ip值与DNA浓度呈良好的线性关系,R2为0.9819.本研究为建立新的微生物分子分型手段提供了初步依据.     

硫化物在乙酰二茂铁修饰碳糊电极上的电化学行为及电分析

研究了S2-在乙酰二茂铁(AFc)修饰碳糊电极(AFc/CPE)上的电催化氧化行为及其电化学分析方法。实验结果表明,AFc/CPE对S2-的电化学氧化具有良好的催化作用。用计时电流法(CA)测定了S2-在AFc/CPE上的电催化氧化反应速率常数k为(2.60±0.05)×105 L.mol-1.s-1。用方波伏安法(SWV)测得催化氧化峰电流与S2-的浓度在5.0×10-5～1.0×10-3 mol.L-1范围内呈良好线性关系,检出限(S/N=3)为1.3×10-7 mol.L-1,同时运用SWV法对造纸废水水样中S2-的含量进行了电化学定量测定。     

Electrochemical Behaviour and Rapid Determination of L‐Dopa at Electrochemically Pretreated Screen Printed Carbon Electrode

A simple and rapid voltammetric method based on a disposable electrochemically pretreated screen‐printed carbon electrode is proposed for the determination of L ‐dopa. Under optimum differential pulse voltammetry conditions a limit of detection of 3.6×10^?7 M for L ‐dopa was obtained. The method was successfully applied to the determination of L ‐dopa in a commercial pharmaceutical formulation.     

木犀草素在玻碳电极上的直接电化学行为及其测定

应用循环伏安法研究木犀草素于玻碳电极的电化学行为.在磷酸盐缓冲液中(pH 4.0),-0.2~+0.8V电位区间内,木犀草素于玻碳电极表面发生的电极反应是吸附控制的准可逆2电子转移过程,电子转移系数α=0.66;建立了检测木犀草素含量的差示脉冲伏安法(DPV).在富集电位+0.4 V下,经富集240 s后,测得木犀草素氧化峰电流Ip与其浓度在1.0×10-8~1.0×10-6mol.L-1范围内呈良好的线性关系,最低检出限为5.0×10-9mol.L-1.本法操作简单、快速、灵敏、准确,可为木犀草素药物质量的控制和检测提供一种简便的新方法.     

基于丝网印刷碳电极的微囊藻毒素-(亮氨酸-精氨酸)的电流型免疫传感器

将微囊藻毒素-(亮氨酸-精氨酸)-鸡卵白蛋白 (Microcystin-(leucinc-arginine)-ovalbumin,MCLR-OVA)固定在锇联吡啶聚(4-乙烯基吡啶)聚合物修饰的丝网印刷碳电极表面,制备了一种检测 MCLR的电流型免疫传感器.该传感器基于间接竞争免疫分析模式,以辣根过氧化物酶偶联的羊抗鼠...     

Carbamate Insecticide Sensing Based on Acetylcholinesterase/Prussian Blue-Multi-Walled Carbon Nanotubes/Screen-Printed Electrodes

Prussian blue (PB)-multi-walled carbon nanotubes (MWCNTs) modified screen-printed electrodes (SPEs) were used to immobilize enzyme acetylcholinesterase (AChE) for carbamate insecticide sensing. The synthesized hybrid PB-MWCNTs had high stability at pH values in the range of 5–10 and presented a porous and homogeneous microenvironment to entrap enzyme molecules. The generated hybrids not only acted as carriers of acetyl cholinesterase, but also promoted electron-transfer reactions because of the synergistic effects between MWCNTs and PB. Under the optimal conditions, the response of the sensor was proportional to acetylthiocholine (ATCh) concentrations ranging from 0.1 mM to 0.6 mM, with a sensitivity of 21.97 µA · mM^?1 · cm^?2. The sensors were further used to detect pesticides, and the inhibition rate of pirimicarb was proportional to the logarithm of its concentration ranging from 1.0 × 10^?6 to 1.0 g · L^?1, with a limit of detection (LOD) equal to 5.32 × 10^?8 g · L^?1. In order to evaluate the performance of the detection system, the sensors were applied to determine pirimicarb in water samples and exhibited high sensitivity and good stability. The detection system is fast, simple for analysis of pirimicarb in environmental samples, and could provide a semi-automated analytical system through further improvement in biosensor arrays.     

阿霉素在多壁碳纳米管膜电极上的电化学行为及其分析研究

报道了一种多壁碳纳米管(MWNT)膜电极的制备方法。研究了阿霉素(ADM)在多壁碳纳米管膜电极上的电化学行为。优化了测定阿霉素的各实验参数,实验证实,ADM浓度在2.0×10-8～1.0×10-5mol/L之间其还原峰电流与浓度有良好的线性关系。富集4min后检测,本法的检出限为5.0×10-9mol/L。用此膜电极测定了病人服用阿霉素后尿样中阿霉素的浓度,取得了满意的结果。