The Use of Automated Headspace Gas Chromatography for Determination of 1,1,1-Trichloroethane in Rat Blood and Brain Tissue

Abstract

1,1,1-trichloroethane in blood and brain tissue from rats which had been artificially ventilated with solvent (8000 ppm) was analysed by automated headspace gas chromatography using a fused silica capillary column. A given concentration of 1,1,1-trichloroethane in the brain could be correlated with a corresponding concentration in the blood; both the uptake and release of the solvent were quicker in blood than in brain. No volatile metabolites of the solvent were found. Automated headspace gas chromatographic analysis is a rapid and sensitive technique for the quantitative registration of volatile organic solvents, e.g. of industrial importance, in body fluids and tissues.     

Microfluidic liquid-liquid extraction system based on stopped-flow technique and liquid core waveguide capillary

In this work, a miniaturized liquid-liquid extraction system under stopped-flow manipulation mode with spectrometric detection was developed. A Teflon AF liquid-core waveguide (LCW) capillary was used to serve as both extraction channel for organic solvent flow and adsorption detection flow cell. Gravity induced hydrostatic pressure was used to drive the organic and aqueous phases through the extraction channels. During extraction process, a stable organic and aqueous phase interface was formed at the outlet of the capillary, through which the analyte in the flowing aqueous stream was extracted into the stationary organic solvent in capillary. The absorbance of the analyte extracted into the organic solvent was measured in situ by a spectrometric detection system with light emitting diode (LED) as light source and photodiode as absorbance detector. The performance of the system was demonstrated in the determination of sodium dodecyl sulfate (SDS) extracted as an ion pair with methylene blue into chloroform. The precision of the measured absorbance for a 5 mg L⁻¹ SDS standard was 6.1% R.S.D. (n = 5). A linear response range of 1-10 mg L⁻¹ SDS was obtained with 5 min extraction period. The limit of detection (LOD) for SDS based on three times standard deviation of the blank response was 0.25 mg L⁻¹.     

Glass Capillary Columns In The Gas Chromatographic And Gas Chkomatocraphic-Mass Spectrometry Determination Of Trace Levels Of Kepone In Natural Waters

Abstract

The application of high-resolution glass capillary columns to the analysis for Kepone in environmental samples by gas chromatography and gas chromatography-mass spectrometry is described. Glass capillary columns make possible the rapid screening and analysis of Kepone at a lower detection limit of 2 ng/L in natural waters. However, even with the aid of glass capillary columns, electron capture determinations for Kepone are suDJect to error. The use of isopropanol in solutions containing Kepone was found to reduce the variability of the Kepone detector response by as much as six times. A discussion concerning the intricacies of Kepone analysis in natural waters is given.     

Programmed temperature vaporizer based method for the sensitive determination of trihalomethanes and benzene,toluene, ethylbenzene and xylenes in soils

A methodology based on the coupling of a headspace autosampler with a GC and a MS detector operating in SIM mode has been developed for the determination of volatile organic compounds (THMs and BTEX) in soils. The GC device used is equipped with a programmable temperature vaporizer (PTV) packed with Tenax-TA^® to introduce the samples (the injection mode used was solvent vent), and a modular accelerated column heater (MACH™) to control column temperature. The proposed measurement procedure reduces the sample pretreatment step to a minimum. Combined use of solvent vent injection mode and mass spectrometry detection allows a highly sensitive method to be proposed, with limits of detection of the order of ng/kg for all the target compounds. Furthermore, the capillary column used allows rapid separations of compounds in less than 4.60 min, affording a very short total analysis cycle time of 9 min.     

Determination of Airborne Nicotine by Automatic Two-Stage Thermal Desorption Gas Chromatography

Abstract

An automated two-stage thermal desorption technique has been developed for the determination of airborne nicotine. Pumped samples are collected on adsorbent tubes and analysed by capillary gas chromatography using flame ionisation detection. The preconcentration effect of the adsorbent compared to solvent trapping or solvent desorption methods permits shorter sampling times and precludes the need for a selective detector.

By use of a basic program all exposure volumes and component details are entered into a method run table and after analysis exposure levels are automatically calculated and printed in report form by the data handling system. Consequently a large throughput samples may be analysed automatically and efficiently with minimal analyst involvement or sample preparation.

The technique described was originally developed to sample airborne nicotine in workplace environments where tobacco is processed. Comparison between this technique and the standard NIOSH method for airborne nicotine is discussed.     

Free release static coating of glass capillary columns; rapid coating at lower temperatures and elevated pressures

The coating speed upon static coating of glass capillary columans was evaluated in terms of inner diameter and length of the column, viscosity and pressure of solvent vapor, etc. From the equation obtained it can be shown that a smaller diameter of a microbore column restricts solvent vapor transfer to the orifice of the column drastically. To compensate for this restriction, a higher pressure at the meniscus is needed. As an alternative to using a higher coating temperature, application of more volatile solvents such as n-butane and isobutane is proposed. Several glass capillary columns (130 μm i.d.) were coated with SE-54 dissolved inpentane-acetone mixed with n-butane or isobutane and the column performances were evaluated. Selection of these solvents permitted free release static coating of ca. 100 μm columns at lower or even ambient temperatures and they were equally suitable as commonly applied solvents (e.g. pentane) to coat highly efficient columns.     

Cryogenic oven-trapping gas chromatography for analysis of volatile organic compounds in body fluids

Cryogenic oven-trapping (COT) with capillary GC has been successfully applied to analysis of chloroform, dichloromethane, trichloroethylene, diethyl ether, the components of solvent thinner (ethyl acetate, benzene, n-butanol, toluene, and others), xylene isomers, cyanide, ethanol, hexanes, general anesthetics, and styrene in human body fluids. This COT-GC technique was compared with headspace solid-phase microextraction (SPME) coupled with GC for some volatile organic compounds (VOC); for all compounds compared the sensitivity achieved using COT-GC was more than ten times higher than for headspace SPME-GC. The COT-GC method is recommended for widespread use in forensic and environmental toxicology, because it is simple, requires no special GC operations, and yet enables high sensitivity and high resolution.     

非水毛细管电泳进展

 毛细管电泳通常是在以水为溶剂的缓冲溶液中进行的,事实上以纯有机溶剂替代水介质同样可以完成特殊样品的电泳分离,且存在诸多优点。以所建立的非水毛细管电泳方法为核心,总结了该方法中有机溶剂、电解质的选择原则及溶质-添加剂相互作用模式,并综述了它在无机离子、中性物质、有机酸等化合物分离分析中的应用。71篇。     

Isolation and Determination of Volatile Organic Compounds from Water by Dynamic Purge-and-Trap Technique Coupled with Capillary Gas Chromatography

The preconcentration technique of purge-and-trap has been investigated in the present work for quantitative adsorption of volatile organic pollutants purged from water samples. A dynamic purging device with variable volume size has been constructed and tested to purge different concentrations of organic compounds. With Tenax GR as the adsorbent, a dynamic purge-and-trap technique was developed combining on-column preconcentration procedures using ambient trapping/thermal desorption/cryogenic focusing/back-flash injection prior to separation and determination using capillary gas chromatography. Various aromatic compounds in water were determined, giving linear working ranges over five orders of magnitude from 0.02 to 5000 µg/L. The analytical procedures were optimized under the assistance of ultrasonication with results validated for the determination of organic contaminants in underground water and tap water, giving over 93% recoveries and a detection limit of 0.01 µg/L, two orders of magnitude lower than those obtained using commercial available instruments with on-line configuration to minimize cross-contamination. The technique provides a potential automated method for in situ monitoring of volatile organic compounds in water.     

Dynamic capillary diffusion system for monoterpene and sesquiterpene calibration: quantitative measurement and determination of physical properties

This article describes a method for preparation of low concentration gas standard mixtures of biogenic volatile organic compounds (BVOCs) emitted primarily by plants. A set of 10 plant volatiles including α-pinene, β-pinene, 3-carene, linalool, methyl salicylate, α-cedrene, β-caryophyllene, β-farnesene, aromadendrene and α-humulene was used in the study. Gas standard mixture of these compounds was generated using a capillary diffusion system (CDS). Diffusion coefficient (D) and saturation vapour pressure (p _s) data of these compounds were calculated from experimentally determined gas chromatographic retention indices (RI) and empirical relationships between D and p _s versus RI. A comparison of the calculated and measured concentrations of investigated compounds has proved that designed CDS can be successfully used for the proper quantification of BVOCs.     

Dynamic headspace analysis of solid waste materials

A dynamic headspace stripping technique for the extraction of volatile organic compounds has been applied to a variety of solid and semisolid waste materials. A simple glass apparatus accommodates a wide range of sample sizes and allows for the volatiles to be stripped at elevated temperatures. Concentration on Tenax, followed by thermal desorption and analysis by fused silica capillary gas chromatography provides detailed information on the volatile content of waste samples of widely differing matrix composition.     

Sampling and Analysis of Odorous Compounds in Water Treatment Plants

Abstract

The following analytical method has been used to identify some odorous compounds in the air of the water treatment plant Werdholzli, Zurich: sampling of contaminated air with the help of activated carbon, desorption by the solvents carbon disulphide and methylene chloride, separation of the carbon disulfide extract into a polar and a nonpolar fraction by adsorption column chromatography on silica. Hereafter gaschromatographic analysis of the polar fraction on glass capillary column (Ucon HB 5100); detection and identification were achieved by flame ionisation, thermoionic nitrogen selective detector and computerized mass spectrometry (Finnigan 3200 F, data system 6110).

The results show the presence of sulfur compounds: thiophenes, thiazoles; nitrogen compounds: pyrazines; oxygen compounds: phenols, alcohols and some unsatured hydrocarbons. The malodorous compounds were sulfur and nitrogen compounds in the range of 0.01-0.1 ppm.     

Simultaneous analysis of 23 priority volatile compounds in water by solid-phase microextraction–gas chromatography–mass spectrometry and estimation of the method's uncertainty

Most water contaminations with volatile organic compounds (VOCs) are traceable to leaking underground fuel reservoirs, solvent storage vessels, agricultural practices, industrial residues, and deficient wastewater treatment and disposal. In order to perform effective monitoring of such organic micropollutants in a straightforward manner, a multiresidue method for the determination of 23 VOCs (trihalomethanes (THMs), BTEX and chlorinated solvents) in water has been developed using solid-phase microextraction (SPME) and capillary gas chromatography–mass spectrometry (GC–MS). This group includes also methyl-tert-butyl ether, epichlorhydrine, and vinyl chloride which present additional analytical difficulties. Three different fibres were assayed: 7-µm polydimethylsiloxane (PDMS), 100-µm PDMS, and 75-µm Carboxen-PDMS, and the extraction conditions were optimized. The best results for the majority of the analytes and mainly for those with the lowest signals were obtained using the Carboxen-PDMS fibre after 15 min of extraction in the headspace mode at a room temperature of 20 ± 2°C. The analytical sensitivity, linearity, precision, accuracy, and uncertainties have been studied for method validation in agreement with the international standard ISO/IEC 17025:2005. The limits of detection achieved with the proposed method (0.06–0.17 µg L^?1) are adequate to determine the VOCs at the restrictive levels established by the European legislation. This was a decisive achievement to enable the analysis of all VOCs listed under the drinking-water directive in a single assay. The method exhibits performance capabilities suitable for routine analysis of VOCs in drinking-water by quality-control laboratories as enforced by EU Directives. The method is currently being used for this purpose, and participation in proficiency tests was assessed, with encouraging results.     

CE separation of various analytes of biological origin using polyether ether ketone capillaries and contactless conductivity detection

The development of efficient and sensitive analytical methods for the separation, identification and quantification of complex biological samples is continuously a topic of high interest in biological science. In the present study, the possibility of using a polyether ether ketone (PEEK) capillary for the CE separation of peptides, proteins and other biological samples was examined. The performance of the tubing was compared with that of traditional silica capillaries. The CE analysis was performed using contactless conductivity detection (C⁴D), which eliminated any need for the detection window and was suitable for the detection of optically inactive compounds. In the PEEK capillary the cathodic EOF was low and of excellent stability even at extremes pH. In view of this fast biological anions were analyzed using an opposite end injection technique without compromising separation. A comparison of the performances of fused‐silica and polymer capillaries during the separation of model sample mixtures demonstrated the efficiency and separation resolution of the latter to be higher and the reproducibility of the migration times and peak areas is better. Furthermore, PEEK capillaries allowed using simple experimental conditions without any complicated modification of the capillary surface or use of an intricate buffer composition. The PEEK capillaries are considered as an attractive alternative to the traditional fused‐silica capillaries and may be used for the analysis of complex biological mixtures as well as for developing portable devices.     

Determination of methylmercury in biological samples by capillary gas chromatography with electron capture detection

A precise and accurate method has been developed for the determination of methylmercury in biological material using capillary gas chromatography with electron-capture detection. Homogenized fish or mussel samples were digested with acid, spiked with ethylmercury chloride as an internal standard and extracted with toluene. After treatment of the solvent extract with sodium thiosulphate and cupric bromide the alkylmercurials were extracted into benzene as their bromide derivatives and analyzed using an OV-275 coated glass capillary column. The detection limit of the method for methylmercury was 5 g/kg tissue.     

Concentration of volatile organic compounds from solvents by sustained chromatographic evaporation

A system for quantitative concentration of volatile organic trace compounds present in organic solvents is described. Evaporation of the solvent is carried out inside a glass capillary tube by the action of a carrier gas, and large volumes can be reduced by a repeated sample injection and a cyclic flow reversal. Best recovery is obtained when a barrier of pure solvent is maintained ahead of the sample during concentration. Four rotary valves are employed for sample and solvent injection and direction of the gas flow. In principle, indefinite sample volumes can be handled, the limit being set by system contaminants. The process was evaluated both off-line and on-line to a gas chromatograph. Concentration of compounds like methylcyclopentane, hexane, and cyclohexane present in pentane in the low nanogram range and subsequent on-line transfer to a gas chromatograph could be performed with a quantitative recovery. The technique was applied to analysis of trace volatiles in drinking water. Detection limits were estimated to be approximately 0.02 ng/L for normal hydrocarbons (FID detection) when concentration of a pentane extract from a one litre water sample was carried out.     

A simple solvent collection technique for a dispersive liquid–liquid microextraction of parabens from aqueous samples using low‐density organic solvent

A simple technique for the collection of an extraction solvent lighter than water after dispersive liquid–liquid microextraction combined with high‐performance liquid chromatography with ultraviolet detection was developed for the determination of four paraben preservatives in aqueous samples. After the extraction procedure, low‐density organic solvent together with some little aqueous phase was separated by using a disposable glass Pasteur pipette. Next, the flow of the aqueous phase was stopped by successive dipping the capillary tip of the pipette into anhydrous Na₂SO₄. The upper organic layer was then removed simply with a microsyringe and injected into the high‐performance liquid chromatography system. Experimental parameters that affect the extraction efficiency were investigated and optimized. Under optimal extraction conditions, the extraction recoveries ranged from 25 to 86%. Good linearity with coefficients with the square of correlation coefficients ranging from 0.9984 to 0.9998 was observed in the concentration range of 0.001–0.5 μg/mL. The relative standard deviations ranged from 4.1 to 9.3% (n = 5) for all compounds. The limits of detection ranged from 0.021 to 0.046 ng/mL. The method was successfully applied for the determination of parabens in tap water and fruit juice samples and good recoveries (61–108%) were achieved for spiked samples.     

Rapid determination of triclosan in personal care products using new in-tube based ultrasound-assisted salt-induced liquid–liquid microextraction coupled with high performance liquid chromatography-ultraviolet detection

This paper describes the development of a novel, simple and efficient in-tube based ultrasound-assisted salt-induced liquid–liquid microextraction (IT-USA-SI-LLME) technique for the rapid determination of triclosan (TCS) in personal care products by high performance liquid chromatography-ultraviolet (HPLC-UV) detection. IT-USA-SI-LLME method is based on the rapid phase separation of water-miscible organic solvent from the aqueous phase in the presence of high concentration of salt (salting-out phenomena) under ultrasonication. In the present work, an indigenously fabricated home-made glass extraction device (8-mL glass tube inbuilt with a self-scaled capillary tip) was utilized as the phase separation device for USA-SI-LLME. After the extraction, the upper extractant layer was narrowed into the self-scaled capillary tip by pushing the plunger plug; thus, the collection and measurement of the upper organic solvent layer was simple and convenient. The effects of various parameters on the extraction efficiency were thoroughly evaluated and optimized. Under optimal conditions, detection was linear in the concentration range of 0.4–100 ng mL⁻¹ with correlation coefficient of 0.9968. The limit of detection was 0.09 ng mL⁻¹ and the relative standard deviations ranged between 0.8 and 5.3% (n = 5). The applicability of the developed method was demonstrated for the analysis of TCS in different commercial personal care products and the relative recoveries ranged from 90.4 to 98.5%. The present method was proven to be a simple, sensitive, less organic solvent consuming, inexpensive and rapid procedure for analysis of TCS in a variety of commercially available personal care products or cosmetic preparations.     

Validated Assay for the Determination of Mitoxantrone in Pharmaceuticals Using Capillary Zone Electrophoresis

Abstract

The first capillary zone electrophoretic (CZE) method for the determination of mitoxantrone (MTX) in pharmaceutical formulations was developed. The influence of background electrolyte (BGE) species, pH, concentration (c _BGE), organic modifier, capillary temperature, applied voltage, and injection time was investigated. Optimum results were achieved with 25 mM ammonium acetate at an apparent pH value of 5.0 in 50% v/v acetonitrile, applied voltage of +30 kV, and capillary temperature of 25°C. The samples were introduced into the capillary hydrodynamically for 2 s at 33.5 mbar. Mitoxantrone was detected at a wavelength of 242 nm. Mitoxantrone and doxorubicin (DOX) (used as internal standard, ISTD) were completely separated in less than 7 min. The method was suitably validated with respect to linearity, limits of detection (LOD) and quantification (LOQ), accuracy, precision, selectivity, and robustness. The proposed method was applied successfully for the determination of MTX in its injectable pharmaceutical formulation.     

Headspace Single-Drop Microextraction with Gas Chromatography for Determination of Volatile Halocarbons in Water Samples

A simple, rapid and inexpensive procedure for extraction and analysis of volatile halocarbons in water samples was presented using the headspace single-drop microextraction (HS-SDME) technique and gas chromatography with microcell electron capture detector (GC-μECD). Operation parameters. such as extraction solvent. headspace volume. organic drop volume. salt concentration. temperature and sampling time, were studied and optimized. Extraction of 10 volatile halocarbon compounds was achieved using the optimized method. Calibration curves of 10 target compounds yielded good linearity in the respective range of concentration (R ² ≥ 0.9968, chlorodibromomethane in the concentration range of 0.05–50 μg/L). The limits of detection were found between 0.002 (tetrachloroethene) and 0.374μg/L (1,1,2-trichloroethane). and relative standard deviations (RSD%) ranged between 4.3 (chloroform) and 9.7% (1,1,2,2-tetrachloroethane). Spiked recoveries of tap water and ground water agreed well with the known values between 118.97 (20.0μg/L of 1,1,2-trichloroethane) and 82.61% (10.0μg/L of tetrachloroethene), demonstrating that the HS-SDME combined GC-μECD was a useful and reliable technique for the rapid determination of volatile halocarbon compounds in water samples.