Nano Silicon from Nano Silica Using Natural Resource (Rha) for Solar Cell Fabrication

Abstract

High purity (～99%) nano silica with an average particle size of ～100 nm was extracted at pH 3 at 650°C from a natural resource, rice husk, using alkaline extraction followed by acid precipitation method. Using nano silica as a precursor, silicon (Si) nanoparticles have been synthesized by high-temperature magnesiothermic reduction method. The prepared sample was characterized by X-ray diffraction, particle size analyzer, Fourier transform infrared spectroscopy, transmission electron microscopy, X-ray fluorescence analyzer, and UV–Vis spectroscopy. The comprehensive characterization studies indicate the pure phase formation of Si and the variation of particle size from 70 nm to 100 nm for samples synthesized at different sintering temperatures. Moreover, the silicon nanoparticles produced at 850°C have pure phase formation, high purity, and good absorption peaks. The efficiency calculated through IV characteristics is found to be increasing in silicon and ruthenium combination (2.67%), which is better than that achieved from the conventional solar cells. The produced silicon nanoparticles could be applied as an anode material for solar cell fabrication.     

微波法制备纳米碳点反应机制与发光机理

为探讨微波法制备纳米碳点发光性质的影响规律与本质,采用微波加热法通过控制微波功率、反应时间以及pH值合成了一系列纳米碳点,并利用荧光激发光谱与发射光谱测试对纳米碳点的发光性质进行了表征,结合紫外吸收光谱与傅立叶红外光谱对反应产物官能团变化分析,最终揭示了微波加热过程中葡萄糖向纳米碳点转变的机制与发光机理。结果表明,采用微波法制备纳米碳点,当微波功率为560 W,反应时间为2.5 min时,获得纳米碳点发光性能最佳。当采用波长370 nm紫外光激发时,对应451 nm的蓝光发射强度最高。伴随纳米碳点溶液pH值从酸性变为碱性,纳米碳点最强发光峰的激发光波长由350 nm显著向高波长方向移动,且发光峰强度显著升高。紫外吸收光谱与傅立叶红外光谱显示反应过程中形成了多环芳香族碳氢化合物,表明微波加热过程中是葡萄糖单糖向多糖聚合并最终发生碳化的过程。不同pH值下纳米碳点发光性质的差异,源于对纳米碳点中C=C键与C=O键比例的调整,从而实现对纳米碳点的光学带隙宽度及激子束缚能等的综合调控。     

Study on the Ultrahigh Quantum Yield of Fluorescent P,O‐g‐C3N4 Nanodots and its Application in Cell Imaging

Graphitic carbon nitride nanodots (g‐C₃N₄ nanodots), as a new kind of heavy‐metal‐free quantum dots, have attracted considerable attention because of their unique physical and chemical properties. Although various methods to obtain g‐C₃N₄ nanodots have been reported, it is still a challenge to synthesize g‐C₃N₄ nanodots with ultrahigh fluorescence quantum yield (QY). In this study, highly fluorescent phosphorus/oxygen‐doped graphitic carbon nitride (P,O‐g‐C₃N₄) nanodots were prepared by chemical oxidation and hydrothermal etching of bulk P‐g‐C₃N₄ derived from the pyrolysis of phytic acid and melamine. The as‐prepared P,O‐g‐C₃N₄ nanodots showed strong blue fluorescence and a relatively high QY of up to 90.2 %, which can be ascribed to intrinsic phosphorus/oxygen‐containing groups, and surface‐oxidation‐related fluorescence enhancement. In addition, the P,O‐g‐C₃N₄ nanodots were explored for cell imaging with excellent stability and biocompatibility, which suggest that they have great potential in biological applications.     

Synthesis and Characterisation of Fluorescent Carbon Nanodots Produced in Ionic Liquids by Laser Ablation

Carbon nanodots (C‐dots) with an average size of 1.5 and 3.0 nm were produced by laser ablation in different imidazolium ionic liquids (ILs), namely, 1‐n‐butyl‐3‐methylimidazolium tetrafluoroborate (BMI.BF₄), 1‐n‐butyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (BMI.NTf₂) and 1‐n‐octyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (OMI.NTf₂). The mean size of the nanoparticles is influenced by the imidazolium alkyl side chain but not by the nature of the anion. However, by varying the anion (BF₄ vs. NTf₂) it was possible to detect a significant modification of the fluorescence properties. The C‐dots are much probably stabilised by an electrostatic layer of the IL and this interaction has played an important role with regard to the formation, stabilisation and photoluminescence properties of the nanodots. A tuneable broadband fluorescence emission from the colloidal suspension was observed under ultraviolet/visible excitation with fluorescence lifetimes fitted by a multi‐exponential decay with average values around 7 ns.     

Detection of Casting Material on Historical Violins by Infrared Spectroscopy and Total Reflection X-Ray Fluorescence Spectrometry

Abstract

Infrared spectroscopy and total reflection X-ray fluorescence spectrometry are used for the analysis of historical varnishes. Total reflection X-ray fluorescence spectrometry is used in the analysis of the elemental composition; infrared spectroscopy is used to determine the inorganic and organic molecules of the binding media, pigments and additives. On historical violins made by A. Guarneri and L. Widhalm silicon and tin were found by total reflection X-ray fluorescence spectrometry. Silicon was proved to be present in the form of silicon rubber by infrared spectroscopy. A further experiment confirmed that the treatment of a violin with silicon rubber casting material is detectable.     

Enzyme-Induced Chemiluminescence-Determination of Blood Glucose Using Luminol

Abstract

Hydrogen peroxide, produced by the interaction of glucose with immobilized glucose oxidase, reacts with the ferricyanide-luminol system to produce chemiluminescence linearly proportional to glucose concentration. The coupled reaction is used as a sensitive precise micro method for the determination of true blood glucose. The linear range of detection is 10^?7 - 10^?4 M glucose. The method correlates quantitatively with two glucose reference techniques.     

Spectrofluorimetric Determination of Chlorpromazine Hydrochloride and Thioridazine Hydrochloride

Abstract

Fluorescence spectroscopy was applied to the development of a sensitive and simple method for the determination of chlorpromazine HCl and thioridazine-HCl. The method is based upon development of an intense fluorescence using N-bromosuccinimide as the fluorogenic reagent. The produced fluorescence has very characteristic excitation and emission spectra and was stable for at least one hour. The results were reproducible and as little as 5 ng/ml chloropromazine HCl and 1 ng/ml thioridazine-HCl could be determined. The method was applied successfully to the analysis of various commercially available dosage forms. The obtained results were in good agreement with those of the official BP 93 procedures.     

Facile synthesis of tomato-based carbon nanodots and its utilization in sensitive detection of tartrazine

Carbon nanodots (CDs) with superior fluorescence performance were obtained by hydrothermal method using tomatoes as raw materials. When the ultraviolet absorption band of tartrazine and the fluorescence spectrum of CDs have complementary overlaps, the fluorescent internal filter effect (IFE) occurred. Furthermore, the degree of quenching of fluorescence intensity of CDs has an excellent linear correlation with tartrazine concentration. And based on this principle, a method for detecting tartrazine was established. As the decrease of fluorescence intensity, tartrazine can be measured in the linear range of 0.1 μM–40 μM. The detection limit is 39 nM, and the recovery rate is 90.7%～114.5%. The established protocol was also effectively employed to assay tartrazine in beverage samples, indicating that it has great potential for food color analysis.     

Oxidized Carbon Nitrides: Water‐Dispersible,Atomically Thin Carbon Nitride‐Based Nanodots and Their Performances as Bioimaging Probes

Three‐dimensional (3D) carbon nitride (C₃N₄)‐based materials show excellent performance in a wide range of applications because of their suitable band structures. To realize the great promise of two‐dimensional (2D) allotropes of various 3D materials, it is highly important to develop routes for the production of 2D C₃N₄ materials, which are one‐atom thick, in order to understand their intrinsic properties and identify their possible applications. In this work, water‐dispersible, atomically thin, and small carbon nitride nanodots were produced using the chemical oxidation of graphitic C₃N₄. Various analyses, including X‐ray diffraction, X‐ray photoelectron, Fourier‐transform infrared spectroscopy, and combustion‐based elemental analysis, and thermogravimetric analysis, confirmed the production of 3D oxidized C₃N₄ materials. The 2D C₃N₄ nanodots were successfully exfoliated as individual single layers; their lateral dimension was several tens of nanometers. They showed strong photoluminescence in the visible region as well as excellent performances as cell‐imaging probes in an in vitro study using confocal fluorescence microscopy.     

The Determination of Silicon in low Alloy Steels by Atomic Fluorescence Spectroscopy in A Separated Nitrous Oxide-Acetylene Flame

Abstract

An atomic fluorescence spectroscopic method is described for the assay of silicon in low alloy steels. The method reported is more sensitive than the corresponding atomic absorption method, the detection limit being 0.7 ppm at 351.6 nm compared to 4 ppm for atomic absorption at the same wavelength.     

采用高分子自组装ZnO纳米线及其形成机理

介绍了一种能在各种晶面的硅衬底上制备垂直于衬底取向生长的ZnO纳米线阵列的新方法. 该法采用高分子络合和低温氧化烧结反应, 以聚乙烯醇(PVA)高分子材料作为自组装络合载体来控制晶体成核和生长. 首先通过PVA侧链上均匀分布的极性基团羟基(—OH)与锌盐溶液中的Zn²⁺离子发生络合作用, 然后滴加氨水调节络合溶液pH值为8.5±0.1, 使络离子Zn²⁺转变为Zn(OH)₂, 再将硅片浸入此溶液中, 从而在硅衬底表面得到较均匀的Zn(OH)₂纳米点, 随后在125 ℃左右Zn(OH)₂纳米点通过热分解转化为ZnO纳米点, 其后在420 ℃烧结过程中衬底上的ZnO纳米点在PVA高分子网络骨架对其直径的限域下逐渐取向生长成ZnO纳米线, 并且烧结初期PVA碳化形成的碳通过碳热还原ZnO为Zn, 再在氧气氛中氧化为ZnO的方式在纳米线顶端形成了催化活性点, 促进了纳米线顶端ZnO的吸收. 烧结后碳逐渐氧化被完全去除. 采用场发射扫描电镜(FE-SEM)、透射电镜(TEM, HR-TEM)和X射线衍射(XRD)对纳米线的分析结果表明, ZnO纳米线在硅衬底上分布均匀, 具有六方纤锌矿结构, 并且大多沿[0001]方向择优取向生长, 直径为20～80 nm, 长度可从0.5至几微米. 提出了聚合物控制ZnO结晶和形貌的网络骨架限域模型以解释纳米线的生长行为.     

Copper-cysteamine nanoparticles encapsulating fluorocoumarin silicon(IV) phthalocyanines: synthesis,characterization, and photophysical properties

Abstract

Three nanohybrid materials (FCSiPc@PEG-Cu-Cy) using poly (ethylene glycol) copper-cysteamine (PEG-Cu-Cy) nanoparticles as a carrier to load three fluorocoumarin silicon(IV) phthalocyanines (FCSiPcs) were prepared. The morphologies of these nanohybrids were characterized by transmission electron microscopy (TEM). The interactions between PEG-Cu-Cy nanoparticles and three FCSiPcs were studied by UV/Vis and fluorescence spectroscopic methods. The photophysical and photochemical properties of these FCSiPcs were influenced by PEG-Cu-Cy nanoparticles and exhibited substituents dependent of phthalocyanines in nanohybrids. The fluorescence resonance energy transfer (FRET) occurred from FCSiPcs (donors) to PEG-Cu-Cy nanoparticles (acceptors). These nanohybrids may be potential photosensitizers for photodynamic therapy.     

Fluorescence anisotropy: application in quantitative enzymatic determinations

In this work a method is presented for the enzymatic determination of glucose using fluorescence anisotropy. During the enzymatic reaction a change in the fluorescence anisotropy of the glucose oxidase (GOx) is produced; the reaction time at which this change appears (t_m) depends on the glucose concentration. A theoretical study has been developed which enables: (a) the correlation of this change in anisotropy with changes in the intensity and the lifetime of the enzyme fluorescence; from this a model which could be generalized to other flavo-enzymes is proposed; (b) the linking of t_m with glucose concentration.After optimisation, the proposed method allows the determination of glucose over the range 100-1000 mg l⁻¹. The detection limit is 90 mg l⁻¹and the reproducibility is better than 4% (n = 6, [glucose] = 250 mg l⁻¹). Anisotropy is more selective than conventional fluorescence intensity, and this method has therefore been applied to direct glucose determination in fruit juices without the interference caused by the inner filter effect.     

Facile preparation of holmium(III)-doped carbon nanodots for fluorescence/magnetic resonance dual-modal bioimaging

Holmium(III)-doped carbon nanodots (HoBCDs) were synthesized for the first time via hydrothermal treatment of citrate acid (CA), branched-polyethylenimine (BPEI) and diethylenetriamine pentaacetic acid hydrate holmium(III) dihydrogen salt (Ho-DTPA), and their dual-modality bioimaging applications were demonstrated by the use of HeLa cells. The as-prepared nanoprobes exhibited bright fluorescence with an absolute quantum yield of 8% and apparent contrast enhancement in T₁-weighted images.     

Detection of Sn(II) ions via quenching of the fluorescence of carbon nanodots

We report that fluorescent carbon nanodots (C-dots) can act as an optical probe for quantifying Sn(II) ions in aqueous solution. C-dots are synthesized by carbonization and surface oxidation of preformed sago starch nanoparticles. Their fluorescence is significantly quenched by Sn(II) ions, and the effect can be used to determine Sn(II) ions. The highest fluorescence intensity is obtained at a concentration of 1.75 mM of C-dots in aqueous solution. The probe is highly selective and hardly interfered by other ions. The quenching mechanism appears to be predominantly of the static (rather than dynamic) type. Under optimum conditions, there is a linear relationship between fluorescence intensity and Sn(II) ions concentration up to 4 mM, and with a detection limit of 0.36 μM.

Fluorescent turn-off/on bioassay for hemoglobin based on dual-emission carbon nanodots-graphene oxide system with multi-detection strategies

As two members of the carbon materials family, carbon nanodots (CNDs) and graphene oxide (GO) possess many excellent optical properties resulting in a wide range of applications. In this work, the fluorescence of resultant dual-emission carbon nanodots (DECNDs) could be quenched by GO. In the presence of hemoglobin (Hb), the fluorescence would recover resulting from two interactions: one was the direct stacking effect of Hb on GO; the other one was that Hb could cover the surfaces of DECNDs; both of them would prevent the fluorescence quenching of DECNDs by GO. In the light of this mechanism, a novel fluorescent turn-off/on method has been developed for the detection of Hb based on DECNDs-GO system. By virtue of the dual emissions of these CNDs, it is noteworthy that both a single emission and ratiometric of dual emissions can be used to establish linear relationships of Hb: 0.05–300 nM (λem = 386 nm), 5–500 nM (λem = 530 nm), and 50–500 nM (I₅₃₀/I₄₁₀), with the corresponding limit of detection (LOD) as low as 20 pM, 2 nM and 20 nM, respectively. This present system is highly selective toward Hb over other proteins and this reliable method has been successfully applied for the detection of Hb in whole blood samples.     

A novel nonenzymatic fluorescent sensor for glucose based on silica nanoparticles doped with europium coordination compound

Amino-functionalized luminescent silica nanoparticles (LSNPs) doped with the europium(III) mixed complex, Eu(TTA)₃phen with 2-thenoyltrifluoroacetone (TTA) and 1,10-phenanthroline(phen) were synthesized successfully using an revised Stöber method. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier-transform infrared (FTIR), and fluorescence spectroscopy were performed for characterizing the synthesized nanoparticles. In the presence of glucose, the fluorescence intensity of the amino-functionalized LSNPs was enhanced due to the enhanced fluorescence resonance energy transfer. Based on fluorescence-enhancing effect, a simple and sensitive method for the determination of glucose was proposed. Under the optimized experimental conditions, the enhanced fluorescence intensity ratio (ΔF/F₀) was linear with the concentration of glucose (c) in the range of 0.0-180 μg ml⁻¹ with a detection limit of 0.8 μg ml⁻¹ (S/N = 3). The R.S.D. values were 0.33% and 0.37% at the levels of 22.5 and 100 μg ml⁻¹, respectively. The proposed method was applied to the determination of glucose in synthetic samples with satisfactory results. The proposed method was also performed to the analysis of blood glucose in human serum samples and the results were in good agreement with clinical data provided by the hospital, which indicates that the method presented here is not only simple, sensitive, but also reliable and suitable for practical applications.     

On The Fluorometric Method for the Measurement of β-Cyanoalanine Synthase Activity

Abstract

A modification of a fluorescence assay method for β-cyanoalanine synthase has been described which involves the direct coupling of the product of cyanide and cysteine to resazurin, to produce the fluorescent resosurfin, The fluorescence produced was found to be directly proportional to the rate of the reaction.     

A Micro Planar Ampehometric Glucose Sensor Using an Isfet as a Reference Electrode

Abstract

A very small glucose sensor has been realized, which consists of a gold working electrode with a glucose oxidase immobilized membrane on it, and a gold counter electrode, all made on a sapphire substrate. By using the pH sensitive ISFET as a reference electrode, the potential for a solution, whose pH is constant, can be measured and irreversible metal electrodes, such as gold or platinum, can be used as working electrode and counter electrode. The sensor is very suitable for miniaturizing and mass production, because the Integrated Circuit (IC) fabrication process can be applied. The glucose oxidase immobilized membrane was also deposited by a lift off method, one of the IC processes. A glucose concentration, from 1 to 100 mg/dl, was measured with good linear current output.     

Surface cleaning of germanium nanodot ionization substrate for surface‐assisted laser desorption/ionization mass spectrometry

In surface‐assisted laser desorption/ionization mass spectrometry (SALDI‐MS), a chemical background signal, arising from organic contaminants such as plasticizers, is frequently observed mainly under m/z ca. 600, which impairs the advantages of the matrix‐free approach. Silver salts, which are used for the cationization of aromatic compounds, are also difficult to remove completely after the measurements. In this study, surface cleaning techniques used in semiconductor processing were used to clean our developed silicon‐based SALDI substrate on which self‐assembled germanium nanodots (GeNDs) had been deposited (termed a GeND chip). An immersion cleaning method using acetone with sonication, and a sulfuric‐peroxide mixture (SPM) cleaning method using a mixture of H₂SO₄/H₂O₂/deionized water, were examined for their effectiveness in removing organic compounds and residual silver salts. Removal of both types of contaminants was successfully performed by SPM cleaning. The limit of detection for glutathione was improved from ca. 5 pmol without cleaning to ca. 50 fmol after the SPM cleaning. Since GeND chips can tolerate acidic cleaning and sonication due to their chemical inertness and rigid nanodot structures, they appear to be an ideal reusable SALDI substrate. Copyright © 2009 John Wiley & Sons, Ltd.