Measurement of Chelating Agent Levels in Media with High Concentrations of Interfering Metal Ions

Abstract

An ion-exchange method for the measurement of levels of chelating agents in media with high levels of metal ions has been developed. The test solution is passed through a specially prepared ion-exchange column, which both removes metal ion interferences, and places the chelating agent in the copper form. The copper levels in the column effluent are then measured by flame atomic absorption methods, the copper levels corresponding in a 1:1 ratio to the levels of chelating agent in the sample. The detection limit for this method is on the order of 1 ppm copper equivalent chelating capacity, and is applicable in situations where the interfering metal ions are at concentrations in the range of 10^?2 M. The method is reproducible in the pH ranges of 4 to 9 Precision and     

Determination of Copper in Silicates Using Chelating Resin After Decomposition With Teflon Vessel

Abstract

By the combined use of a decomposition vessel, chelating resin, and atomic absorption spectrometry, a simple method for the determination of copper in silicate rocks was devised. A sample was digested overnight at room temperature with small amounts of hydrofluoric acid and aqua regia in the Teflon vessel having a sealing stopper. In the presence of citrate, only the supernatant of the digested sample solution was passed through a small column of the chelating resin, Dowex A-1, at pH 4. After elution with nitric acid, copper was determined by ordinary atomic absorption spectrometry. The recovery, reproducibility, and accuracy of the method were quite satisfactory. The analytical results obtained for the standard rocks agreed well with reported results.     

Determination of Copper in Mineral Waters from Galicia, Spain, by Flame Atomic Absorption Spectrometry Using Preconcentration with Diethyldithiocarbamate Loaded on Silica Gel

Solid phase extraction using sodium diethyldithiocarbamate (DDC) loaded on silica gel has been used for preconcentration of trace amounts of copper from commercial mineral waters prior to its determination by flame atomic absorption spectrometry. The sorption and releasing of copper have been studied under both static and dynamic conditions. A short shaking time is required for quantitative sorption using the batch method, and a high flow-rate (6 ml min⁻¹) can be used in the column method due to the fast sorption and desorption kinetics. The copper concentration found in several mineral waters from Galicia (Spain) ranged from 8.4 to 23.8 μg L⁻¹. There were no significant differences between the solid-phase extraction method and the conventional solvent extraction method which uses DDC as chelating agent.     

Determination of silver(I) ion in water samples by graphite furnace atomic absorption spectrometry after preconcentration with dispersive liquid-liquid microextraction

A method was developed for the determination of silver ion (Ag) by combining dispersive liquid-liquid microextraction preconcentration with graphite furnace atomic absorption spectrometry. Diethyldithiocarbamate was used as a chelating agent, and carbon tetrachloride and methanol as extraction and dispersive solvent. Factors influencing the extraction efficiency of Ag and its subsequent determination were studied and optimized. The detection limit is 12 ng L^?1 (3 s) with an enrichment factor of 132, and the relative standard deviation is 3.5% (n?=?7, at 1.0 ng mL^?1). The method was successfully applied to the determination of trace amounts of Ag in water samples.     

Organic complexation and total dissolved trace metal analysis in estuarine waters: comparison of solvent-extraction graphite furnace atomic absorption spectrometric and chelating resin flow injection inductively coupled plasma-mass spectrometric analysis

The measured concentrations of cadmium, cobalt, copper, nickel, lead, zinc, and manganese in acidified (pH<2) estuarine water samples analyzed for total dissolved trace metal concentrations using on-line chelating resin column partitioning with inductively coupled plasma-mass spectrometry (CRCP-ICP-MS) were compared to those analyzed by graphite furnace atomic absorption spectrometry (GFAAS) after liquid-liquid extraction using a combination of 1-pyrrolidinedithiocarbamate/diethyldithiocarbamate (PDC/DDC). Although there was good agreement between the two sets of analyses for cadmium, lead, manganese, and zinc concentrations, those of cobalt, copper, and nickel determined by CRCP-ICP-MS were found to be 10-20% lower than those determined by solvent-extraction GFAAS. The different yields were positively correlated (R>0.961, simple linear regression) to the dissolved organic carbon (DOC) concentration of the samples. Good agreement between the two methods for cobalt and copper was achieved after ultraviolet (UV) digestion of the acidified samples. Samples collected from the South Bay of the San Francisco Estuary with high DOC showed the greatest difference for cobalt, copper, and nickel which is tentatively attributed to complexation with humic material for copper and cobalt and strong synthetic chelating agents such as ethylenediaminetetraacetic acid (EDTA) for nickel. This is consistent with previous studies on copper, nickel and cobalt complexation in this region. We recommend UV digestion of acidified estuarine samples prior to multi-element analysis by chelating resin flow injection ICP-MS methods.     

The Application of Atomic Absorption Method as a Flow Detector to Gel Chromatography

Abstract

The applicability of atomic absorption method as a flow detector to gel chromatography was discussed. The effluent from the outlet of a Sephadex G-15 column was directly introduced into a nebulizer of atomic absorption spectrometer. It was found that the atomic absorption flow detector was sensitive and highly selective so as to permit the quantitative determination of metal ions. Some advantageous aspects of this detector were also discussed.     

A highly sensitive procedure for determination of ultra trace amounts of molybdenum by graphite furnace atomic absorption spectrometry after dispersive liquid-liquid microextraction

A simple, rapid and sensitive method is developed for selective determination of ultra trace amounts of molybdenum(V?) from different water samples. The method is based on highly efficient separation and pre-concentration of molybdenum(V?) by dispersive liquid-liquid microextraction followed by its determination with graphite furnace atomic absorption spectrometry. Ultra traces of the target ion were extracted and pre-concentrated from acidic water samples by using sodium diethyldithiocarbamate as a suitable chelating agent, and carbon tetrachloride and acetone as extraction and disperser solvents, respectively. After optimizing different parameters, including type and volume of extraction and disperser solvents, pH of test solution, extraction time, volume and concentration of the chelating agent and sample volume, an enrichment factor of 362 was obtained. The linear concentration range, limit of detection and relative standard deviation of the method were evaluated as 0.04–0.8 ng mL^?1, 0.007 ng mL^?1 and 4.5%, respectively. This method was applied successfully to the determination of molybdenum in tap water and wastewater samples.     

Analytical Separation of Copper(II), Cobalt(II) and Nickel(II) Using Polymer Bound Anthrantic Acid

Abstract

The preferential complexing tendency of different nietal ions towards chelating agents anchored on a polymer has been used for separation of transition metals. the anthranilic acid group was anchored on the polymeric cellulose back-bone by successive coupling with trifunctional reagent cyanuric chloride, in diozane medium, at pH 7 and 9–10, respectively. This polymer bound chelating agent was used to separate copper(II), nickel(II) and cobalt(II) in the concentration range 1.0–0.1 mmol/L. the separation of a mixture of two components was quantitative using column chromatography.     

Determination of selenium by atomic absorption spectrometry with miniaturized suction-flow hydride generation and on-line removal of interferences

On-line removal of transition metal interferences in microscale suction-flow hydride generation atomic absorption spectrometry is described for the determination of selenium at μg l^?1 levels. A mini-column of a chelating resin with iminodiacetate groups is used. Selenium in solutions containing ? 2.5 mg of copper or nickel was determined at a rate of 30 samples per hour; the detection limit was 0.1 ng of selenium. The relative standard deviation for ten replicate measurements of 5 ng of selenium was 3.8%. The method was applied successfully to the determination of selenium in standard copper alloys and nickel sponge.     

Atomic Absorption Spectrophotometry as a Chromatography Detector for Copper-Amino Acid Complexes in Human Serum

Abstract

In this paper an automatic sampling device is used for the electrothermal atomic absorption detection of copper-amino acid complexes in human serum after separation on an ion exchange chromatographic column. Adsorption chromatography on a silica gel column is used to separate the major naturally occurring copper amino-acids, copper-histidine and copper-glutamine, with subsequent detection by electrothermal atomic absorption.     

Dispersive liquid-liquid microextraction preconcentration of palladium in water samples and determination by graphite furnace atomic absorption spectrometry

A new method for the determination of palladium was developed by dispersive liquid-liquid microextraction preconcentration and graphite furnace atomic absorption spectrometry detection. In the proposed approach, diethyldithiocarbamate (DDTC) was used as a chelating agent, and carbon tetrachloride and ethanol were selected as extraction and dispersive solvent. Some factors influencing the extraction efficiency of palladium and its subsequent determination, including extraction and dispersive solvent type and volume, pH of sample solution, concentration of the chelating agent and extraction time, were studied and optimized. Under the optimum conditions, the enrichment factor of this method for palladium reached at 156. The detection limit for palladium was 2.4 ng L⁻¹ (3σ), and the relative standard deviation (R.S.D.) was 4.3% (n = 7, c = 1.0 ng mL⁻¹). The method was successfully applied to the determination of trace amount of palladium in water samples.     

Determination of Ultratrace Amounts of Copper and Cadmium in Seawater by Graphite Furnace Atomic Absorption Spectrometry with Flow-Injection Semi On-line Preconcentration

Methods are described for the determination of ultratrace amounts of copper and cadmium in seawater by graphite furnace atomic absorption spectrometry with flow-injection, microcolumn preconcentration. A new type of C₁₈ column loaded with sodium diethyldithiocarbamate (sodium-DDC) was used to extract copper and cadmium from seawater as the DDC chelates. The analytical effects of the pH of the mixture of the sample and sodium-DDC solutions and the concentration of the chelating reagent were studied. Sodium-DDC-loaded columns and unloaded C₁₈ columns with different shapes and volumes were compared. To determine copper in seawater, a simple aqueous calibration was made with a mixture of palladium and magnesium nitrate as a matrix modifier, while for cadmium no matrix modifier was necessary. This method required only small seawater volumes, 600 and 400 μl for the determination of copper and cadmium respectively, with preconcentration factors of 15-fold for copper and 10-fold for cadmium. Detection limits for the preconcentration of aqueous solutions of copper and cadmium were 0.024 and 0.004 μg liter⁻¹ (3σ), respectively. Results for determinations of copper and cadmium in National Research Council of Canada, CASS-2, Nearshore Seawater Reference Material showed no significant differences between the certified values and the measured values, based on Student′s t test at the 95% confidence level. The relative standard deviations of the various measurements varied between 2 and 8%.     

Complex Formation Studies with Cupric Ion-Selective Membrane Electrodes

Abstract

A cupric ion-selective electrode of the liquid-liquid membrane type is shown to respond selectively to Cu⁺⁺ activity over the range of pCu⁺⁺ = 2–5 in aqueous solutions of pH 3.5–6.5. Cupric ion activity measurements in the presence of complexing ligands have yielded a reliable estimate of formation constants for a number of soluble copper complexes.     

Indirect atomic absorption spectrometric determination of perchlorate by liquid-liquid extraction in a flow-injection system

The determination is based on the continuous liquid-liquid extraction of the copper(I)/6-methylpicolinealdehyde azine/perchlorate ion-pair into 4-methyl-2-pentanone in a flow-injection manifold. The organic fills a loop of an injector situated in an integrated feed system of an atomic absorption spectrometer. Measurement of the copper atomic absorption signal from the organic phase allows the indirect determination of 0.5–5 μg ml^?1 perchlorate, giving a 3-fold increase in sensitivity over the conventional spectrophotometric method. The detection limit is 70 ng ml^?1. The sampling frequency is 45 ± 5 h^?1. The method is highly selective, and has been used for the determination of perchlorate added to serum and urine samples.     

An Automated Method for the Determination of Enoximone and Its Major Sulfoxide Metabolite in Plasma Using Robotic Technology–High Performance Liquid Chromatography

Abstract

An automated analytical procedure for the determination of enoximone, a new cardiotonic agent, and its major oxidative metabolite in plasma using robotic technology is described. A Zymark robot is used to perform all the operations of solid phase extraction including column pretreatment, internal standard addition, sample mixing, sample pipetting, column rinsing, drying and sample elution. The processed sample is injected directly into the high performance liquid chromatography system which is equipped with an ultraviolet absorption detector. The assay has good precision and accuracy, equivalent to the manual method it replaces, and yet provides higher throughput of sample.     

Atomic Absorption Spectrophotometric Analysis of Condensed Phosphates by a Flow Detector Connected with a Gel Chromatographic Column

Abstract

An atomic absorption flow detector combined with a gel chromatographic column (Sephadex G-25) gives a sensitive and quantitative method of determining various condensed phosphates such as diphosphate, tri-phosphate, tetraphosphate and Kurrol's salt. This method is based on the automatic recording of atomic absorption at the resonance line of magnesium due to magnesium complexes of condensed phosphates which are produced during the elution of condensed phosphate anions through the column pre-equilibrated with a magnesium chloride solution.     

Flame atomic absorption spectrometry determination of trace amounts of copper after separation and preconcentration onto TDMBAC-treated analcime pyrocatechol-immobilized

A simple and reliable method has been developed for green separation and preconcentration of trace amounts of copper ions in aqueous solutions for subsequent measurement by flame atomic absorption spectrometry (FAAS). The Cu²⁺ ions are adsorbed selectively and quantitatively during the passage of an aqueous solution through TDMBAC-treated analcime pyrocatechol-immobilized. The retained copper ions were desorbed from the column with 5.0 mL of 4 mol L⁻¹ nitric acid solutions as eluent and were determined by FAAS. The linear range was 0.2-75 ng mL⁻¹ in the original solution with a correlation coefficient of 0.9987. In this case we can concentrate 0.1 μg of copper from 1000 mL of solution and the proposed method permits a large enrichment factor (about 200). The detection limit of the proposed method is 0.05 ng mL⁻¹ in the original solution (2σ_bl). Determination of copper in standard alloys showed that the proposed method has good accuracy (recovery was more than 97%). The method was successfully applied for recovery and determination of copper in several water samples.     

The application of chelate systems to partition chromatography: preliminary paper

It has been found possible to retain solutions of chelating agents on a solid supporting medium, and in this paper preliminary investigations are reported which were carried out to determine the extraction behaviour of radioactive copper between an aqueous hydrochloric acid phase and a solution of dithizone in an organic solvent retained on silica gel. Chloroform was found to be a very satisfactory solvent and carbon tetrachloride was also used. For both of these solvents the extraction vs. acidity curves were found to be similar to the corresponding liquid-liquid extraction. The high values for the fraction extracted show that this method would provide a useful technique for the concentration of copper from aqueous solution, and the similarity between the liquid-liquid and liquid-solid extractions suggests that it may be possible to adapt conventional liquid-liquid extractions to work on the column principle.     

Column Chromatographic Preconcentration of Copper in Alloys and Complex Materials Using 9,10 Phenanthrenequinone Monoxime Supported on Naphthalene

Abstract

A solid chelating compound phenanthrenequinone monoxime PQM) supported on naphthalene provides a rapid and economical means of preconcentration and separation of copper from the aqueous samples. Copper forms a complex with PC:: supported on naphthalene in the column at pH 6.1–8.4 with a flow rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of DMF and the absorbance is measured at 470 nm against reacent blank. Beer's law is obeyed in the concentration range 0.6 9.6 μg of copper in 5 ml of DMF. The molar absorptivity and sensitivity are 6.3×10⁴ L mol^?1 cm^?1 and 0.001 μg cm^?2 respectively.     

Preconcentration and determination of ultra trace amounts of palladium in water samples by dispersive liquid-liquid microextraction and graphite furnace atomic absorption spectrometry

A highly sensitive, simple and rapid method is presented for the determination of palladium using graphite furnace atomic absorption spectrometry after its separation and preconcentration by dispersive liquid-liquid microextraction. Ultra traces of Pd were extracted and preconcentrated in acidic water samples by using 2-amino-1-cyclohexene-1-dithiocarboxylic acid as a suitable chelating agent, and carbon tetrachloride and acetone as extraction and disperser solvents, respectively. The experimental parameters were optimized in order to enhance the extraction efficiency. After optimizing the extraction conditions and various instrumental parameters, an enhancement factor of 350 was obtained. The analytical curve absorbance vs. concentration was linear over the range 0.02–0.6 µg L^-1 Pd. The detection limit and relative standard deviation were 0.007 µg L^-1 and 4.2%, respectively. The method was successfully applied to the determination of palladium in roadside soil and several aqueous samples.