Fabrication and Characterization of Novel Salicylic Acid Sensors Using Different Reagents (Ferric and Copper)

Abstract

Fabrication of optical fiber salicylic acid (SA) sensors based on immobilization of ferric(III) nitrate and copper(II) acetate on Dowex‐50x8 is presented in this paper. The SA forms a stable purple complex with immobilized Fe³⁺ at pH 2.1 with a response time of 10 min while it forms a stable yellowish green complex with immobilized Cu²⁺ at pH 6.5 with a response time of 8 min. The reflectance spectra of the sensors were measured by using an optical fiber spectrophotometer. The results showed these SA sensors have maximum reflectance at 786 nm and 725 nm for SAFe complex and SACu complex, respectively. The useful dynamic response ranges are 0.02–0.50 g/L (SAFe) and 0.40–1.40 g/L (SACu). These complexes are stable for more than 24 hours. A good reproducibility (0.90%— SAFe; 0.86%— SACu) of measurement was obtained with these sensors.     

Ferric(III) Nitrate Supported on Kieselguhr: A New Reagent for Selective Oxidation of Alcohols

A selective and effective oxidation of alcohols into the corresponding aldehydes and ketones, respectively, with a new reagent, ferric(III) nitrate supported on kieselguhr, under heterogeneous conditions is reported.     

Prediction of High Performance Fibers Strength Using Back Propagation Neural Network

Nowadays, quantification of the effects of basic parameters such as precursor, temperature oxidation, residence time, low temperature carbonization (LTC) and high temperature carbonization (HTC) on production process polyacrylonitrile based carbon fibers is not completely understood. In this way, there is not a completely theoretical model that accomplishes to quantitatively describe production process carbon fibers very accurately which needs to be used by engineers in design, simulation and operation of that process. This paper presents the development of a back propagation neural network model for the prediction of carbon fibers produced from PAN fibers. The model is based on experimental data. The precursors, temperature oxidation, residence time, LTC and HTC have been considered as the input parameters and the strength as output parameter to develop the model. The developed model is then compared with experimental results and it is found that the results obtained from the neural network model are accurate in predicting the strength of carbon fibers.     

Spectrophotometric Determination of Antimony (III) By Solvent Extraction with Mandelic Acid and Malachite Green

Abstract

A sensitive and selective method has been developed for the spectrophotometric determination of antimony in the tervalent oxidation state. It was found that antimony (III) reacts with mandelic acid to form a complex anion extractable into chlorobenzene with malachite green in weak acidic media (pH 2.2 to 3.5) at room temperature and is determined indirectly by measuring the absorbance of malachite green in the extract at 628 nm. The calibration graph is linear for antimony (III) over the range 0.088–1.8 mg 1^?1 (7.2 × 10^?7–1.5 × 10^?5 mol 1^?1) with the apparent molar absorptivity ε × 6.9 × 10⁴ 1 mol^?1 cm^?1. Antimony (V) was slightly extracted in the presence of phosphate buffer with ε × 2.7 × 10³ 1 mol^?1 cm^?1.     

神经网络方法在血管紧张素转换酶抑制剂定量构效关系建模中的应用

对20个ACEI化合物用量子化学方法进行结构优化并计算出10个参数,用9种不同隐含层节点数的BP神经网络研究了ACEI的定量构效关系,建立了节点为10/6/1的三层BP神经网络模型。结果表明:以量化理论计算所得参数可以构建合理的ACEI定量构效关系模型,神经网络模型M6的r2=0.995,S=0.050,6个验证集化合物的残差平方和为0.002,预测能力明显强于多元线形回归模型,亦优于同类文献报道,可作为ACEI研发领域中预测先导化合物活性的理论工具。     

Advanced Synthesis of Dihydrofurans: Effect of Formic Acid on the Mn(III)-Based Oxidation

The Mn(III)-based oxidation of a tertiary alkylamine, such as nitrilotris(ethane-2,1-diyl) tris(3-oxobutanoate) (1) with 1,1-diphenylethene (2a), effectively proceeded in an acetic acid–formic acid mixed solvent to give nitrilotris(ethane-2,1-diyl) tris(2-methyl-5,5-diphenyl-4,5-dihydrofuran-3-carboxylate) (3). Other typical Mn(III)-based reactions of various β-diketo esters 4a–e, 2,4-pentanedione (6a), malonic acid (6b), and diethyl malonate (6c) with 1,1-diarylthenes 2a–d were also investigated in a similar acetic acid–formic acid mixed solvent and the reaction rate was accelerated and the product yield increased.     

Direct Titration of Nitrate with Diphenylthallium(III) Sulfate

Abstract

Nitrate may be titrated with diphenylthallium(III) sulfate. The titration may be monitored amperometrically or potentiometrically. Fluoride, perchlorate, sulfate and phosphate do not interfere. Chloride, bromide and iodide interfere and must be removed. For amperometric titration, the range is 5 – 22 × 10^?3 M nitrate.     

Fe(III) sequestering agents built on poly(ethylenimine) through crosslinkage of three molecules of a salicylate derivative preassembled by Fe(III) ion

Three molecules of 5-(bromoacetyl) salicylate ( 1 ) complexed to Fe(III) ion were crosslinked with poly(ethylenimine) (PEI) in DMSO by alkylation of amino groups of PEI with 1 , leading to the formation of Fe(Sal)₃PEI, a water-soluble polymer. Several other derivatives including the immobilized form were also prepared. Examination of the values of log K_f for the PEI derivatives indicated that each Fe(III) binding site in Fe(Sal)₃PEI contains three salicylate moieties. In addition, the log K_f revealed that the effective molarity (EM) of the salicylate groups contained in the Fe(III) binding site is ca. 1000M. The high EM value shows that the geometry of the coordination sphere is well conserved during the crosslinkage with PEI of 1 preassembled around Fe(III) ion. In view of the EM value and the pK_a values of salicylic phenols in apo(Sal)₃-PEI, the metal-free form, the three salicylate groups of each Fe(III) binding site appear to occupy proximal positions leading to effective cooperation in Fe(III) binding. Fast, strong, and selective binding of Fe(III) ion by the binding site comprising three salicylate moieties was demonstrated. In addition, rapid demetalation of the resulting complexes as well as chemical stability of the immobilized chelating agents built on PEI were achieved. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1197–1210, 1997     

Simple Method for Determination of Microgram Amounts of L-Ascorbic Acid in Pharmaceuticals with Hexa-Amminecobalt (III) Tricarbonato Cobaltate as Redox Titrant

Abstract

Hexa-anminecobalt (III) tricarbonato cobaltate is used for direct determination of 1 to 100 mg L-ascorbic acid in synthetic standards and different pharmaceutical preparations. The proposed method depends upon visual titration of L-ascorbic acid in the presence of ferroin as indicator.

The effect of common organic acids on ascorbic acid shows little interferences.

12.5 - 1000 mg ascorbic acid in different pharmaceutical preparations are determined with 99.9 - 100.48 % recovery and ± 0.01 to 0.8 % RSD.     

Complexes of Oxamic Acid with La(III), Gd(III), Tb(III), Er(III), Tm(III) and Lu(III)

The preparation, for the first time, of the deprotonated complexes of oxamic acid with La(III), Gd(III), Tb(III), Er(III), Tm(III) and Lu(III) is reported. Analytical results, conductometric measurements, magnetic moments and spectral data (IR and diffuse reflectance spectra) are discussed in terms of possible structural types. The oxamate anion acts as a N, O bidentate non-bridging ligand.     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.     

Multi‐Channel Surface Acoustic Wave (SAW) Sensor Based on Artificial Back Propagation Neural (BPN) Network and Multivariate Linear Regression Analysis (MLR) for Organic Vapors

A six‐channel surface acoustic wave (SAW) detection system with a 315 MHz one‐port quartz resonator and a homemade computer interface for signal acquisition and data processing was developed to detect various organic vapors. The oscillating frequency of the SAW quartz crystal decreased due to the adsorption of organic molecules on the coating materials. Polyethylene glycol, 18 crown 6 (18C6), Cr³⁺/cryptand‐22, stearic acid, polyvinylpyrrolidene and triphenyl phosphine coated quartz crystals were used as sensors. An artificial back propagation neural (BPN) network was used to recognize various organic gases such as hexane, 1‐hexene, 1‐hexyne, 1‐propanol, propionaldehyde, propionic acid and 1‐propylamine. It showed not only the distinction of unity of organic vapors but also mixtures of gases. The learning rate and the hidden unit of a neural network system for BPN analysis were investigated. Furthermore, the concentrations of these organic vapors were computed with about 10% error by multivariate linear regression analysis (MLR). MLR analysis with a multichannel SAW sensor was applied to determine the concentration of each component in a mixture of 1‐hexene, 1‐hexyne and propionaldehyde.     

The Spectrophotometry Determination of Mn(III) in the Presence of Mn(IV)

Abstract

The spectra of complex of Mn(III) and Mn(IV) with pyrophosphoric acid are investigated. The molar absorption coefficient of the complex of Mn(III) with pyrophosphoric acid is 80.6/Mcm at 510nm which is close to that of Mn(IV), 110/Mcm, however, the molar absorption coefficient of the complex of Mn(HI) with pyrophosphoric acid is only 4.98/Mcm at 398nm which is much less than that of Mn(IV), 390/Mcm. Based on this absorbance difference between Mn(III) and Mn(IV) at wavelength 398nm and 510nm, a procedure of determination of Mn(III) in the presence of Mn(IV) has been developed.     

Mechanistic and Spectral Studies of the Ruthenium(III) Catalysed Oxidation of Sulfanilic Acid by Alkaline Hexacyanoferrate(III)

Summary. The kinetics of ruthenium(III) catalysed oxidation of sulfanilic acid (p-aminobenzenesulfonic acid) by hexacyanoferrate(III) in alkaline medium at a constant ionic strength of 2.5mol·dm^–3 has been studied spectrophotometrically using a rapid kinetic accessory. The reaction exhibits 2:8 stoichiometry (SNA:HCF(III)). The reaction showed first order kinetics in [hexacyanoferrate(III)] and [ruthenium(III)] and apparent less than unit order in both sulfanilic acid and alkali concentrations. The reaction rate increases with increasing ionic strength but the relative permittivity (_T) of the medium has a negligible effect on the rate of the reaction. Initial addition of reaction products did not affect the rate significantly. A mechanism involving the formation of a complex between sulfanilic acid and hydroxylated species of ruthenium(III) has been proposed. The active species of HCF(III) and ruthenium(III) are understood as [Fe(CN)₆^3–] and [Ru(H₂O)₅OH]²⁺, respectively. The main products were identified by IR, NMR, and mass spectral studies. The reaction constants involved in the different steps of mechanism are calculated. The activation parameters with respect to the slow step of the mechanism are computed and discussed and thermodynamic quantities are also calculated.     

A facile preparation of donut-like supramolecular tannic acid-Fe(III) composite as biomaterials with magnetic,conductive, and antioxidant properties

Tannic acid (TA) complexes with various metal ions are prepared in buffer solutions by readily adjusting the pH, but there is no normalizing method to produce ferric tannate complexes. In this study, TA-Fe(III) complex was prepared in reverse microemulsion medium by reaction of TA as ligand with Fe(III) in 1:3 ligand:metal ion molar ratio. The complex was characterized by SEM, AFM, FT-IR, elemental analysis, AAS measurement, and Brunauer-Emmett-Teller (BET) method. Furthermore, magnetic susceptibility was tested with the Gouy method, and electronic spectral studies of TA-Fe(III) complex were completed with solid UV–vis measurements. The thermal stability was also studied by TGA analysis. These studies show that the ligand molecules have octahedral arrangement around Fe(III) and the complex is paramagnetic. The bandgap energy of the complex was calculated as 3.42 eV with solid UV–vis analysis. To determine antioxidant activity of the complex, Total Phenol Content (TPC) and Trolox Equivalent Antioxidant Concentration (TEAC) methods were used. The complex has great antioxidant properties with TPC = 45 ± 1 mg L^?1 GAE and TEAC = 296 ± 2 mM trolox g^?1 for dry sample.     

人工神经网络法预测二维色谱柱效

 采用基于变步长BP算法的人工神经网络,对高效微 填充柱-毛细管柱构成的二维柱色谱系统建立了柱效与影响因素的权接拓扑模型, 并用于不同操作条件下二维柱系统的柱效预测中,取得了较好的效果。     

Complexes of oxamic acid with Au(III) and Rh(III)

The preparation and some properties of the deprotonated complexes of oxamic acid with Au(III) and Rh(III) are reported. On the basis of analytical results, conductometric measurements, magnetic moments and spectral data (IR and UV-visible), a square planar structure is proposed for K[AuL(OH)₂] and octahedral for K₃[RhL ₃] 3H₂O (whereLH₂=oxamic acid).L ^2– acts as a bidentate, non-bridging ligand.

---

Komplexe der Oxamidsäure mit Au(III) und Rh(III)

Zusammenfassung Es wird über die Darstellung und einige Eigenschaften von deprotonierten Komplexen der Oxamidsäure mit Au(III) und Rh(III) berichtet. Auf der Grundlage von analytischen Ergebnissen, Leitfähigkeitsmessungen, magnetischen Momenten und IR- und UV(vis)-spektroskopischen Daten wird für K[AuL(OH)₂] eine quadratisch planare und für K₃[RhL ₃] 3 H₂O eine oktaedrische Struktur vorgeschlagen (LH₂=Oxamidsäure).L ^2– reagiert als zweizähniger, nicht überbrückender Ligand.

     

Improved Protocol for Mononitration of Phenols with Bismuth(III) and Iron(III) Nitrates

A simple and efficient multigram procedure was developed for the selective mononitration of various activated phenols. The reaction proceeded smoothly with 0.5 equivalents of Bi(NO₃)₃ · 5H₂O or Fe(NO₃)₃ · 9H₂O in acetone at ambient temperature or at reflux. The desired products were isolated in 62–93% total yield and essentially no overnitrated compounds were detected.     

Ethylenediaminetetraacetic Acid Functionalized Gold Nanoparticles for Sensitive Colorimetric Detection of Chromium(III)

A cost‐effective and sensitive colorimetric method was described for the determination of chromium(III) ion (Cr³⁺) by using ethylenediaminetetraacetic acid functionalized gold nanoparticles (EDTA‐AuNPs) as a probe. The stable and dispersed EDTA‐AuNPs were prepared by reducing HAuCl4 with sodium borohydride in presence of EDTA as a capping agent. Upon the addition of Cr³⁺, the colour of EDTA‐AuNPs solution changed from red to violet, which was in response to the surface plasmon absorption of dispersed and aggregated EDTA‐AuNPs. The procedure allowed the determination of Cr³⁺ in the range of 0.1–1.0 mol/L. The limit of detection for Cr³⁺ was 0.08 mol/L. The relative standard deviation was 2.5 % for eight repeated measurements of 0.6 mol/L Cr³⁺ solution. The method was applied to the determination of Cr³⁺ in water samples.     

The Spectropolarimetric Back-Titration of Rhodium(III) with the Chiral Ligand (R,R)-(-)-Trans-1, 2-Cyclohexanediaminetetraacetic Acid

Abstract

Spectropolarimetric back-titrations are described for rhodium(III); the optically active ligand (R, R)-(-)-t?ans-l, 2-cyclohexanediaminetetraacetic acid (R, R(-)CDTA) is used as the complexing agent and cadmium(II) ion as the back-titrant. The optical rotation is monitored throughout the titration, and the optically active ligand and stereospecifically formed complexes serve as self-indicators. The end points are determined graphically by straight-line extrapolations from a plot of volume-corrected observed rotations versus ml of titrant. The rhodium(III) titration plots are representative of normal spectro-polarimetric back-titrations. The range of analyses of rhodium(III) was from 40–0.5 mg.