Square‐Wave Voltammetry Determination of Aspartame in Dietary Products Using a Boron‐Doped Diamond Electrode

Abstract

The use of square‐wave voltammetry in conjunction with a cathodically pretreated boron‐doped diamond electrode for the analytical determination of aspartame in dietary products is described. In this determination, the samples were analyzed without previous treatment in a 0.5 mol l^?1 H₂SO₄ solution. A single oxidation peak at a potential of 1.6 V vs. Ag/AgCl (3.0 mol l^?1 KCl) with the characteristics of an irreversible reaction was obtained. The analytical curve was linear in the aspartame concentration range 9.9×10^?6 to 5.2×10^?5 mol l^?1 with a detection limit of 2.3×10^?7 mol l^?1. The relative standard deviation (n=5) obtained was smaller than 0.2% for the 1.0×10^?4 mol l^?1 aspartame solution. The proposed method was applied with success to the determination of aspartame in several dietary products and the results were similar to those obtained using an HPLC method at 95% confidence level.     

Development of a Solid‐Phase Extraction‐Enzyme‐Linked Immunosorbent Assay Method with a New Sorbent of Multiwall Carbon Nanotube for the Determination of Estrone in Water

Abstract

A sensitive solid‐phase extraction‐enzyme‐linked immunosorbent assay (SPE‐ELISA) method was developed to analyze the estrone in environmental water. A new SPE sorbent of the multiwall carbon nanotube was tested and proved to have similar adsorbability for estrone comparing to the commercial C₁₈ SPE. A specific polyclonal antibody for estrone (A‐E1) and a broad‐spectrum antibody for estrone, estradiol and estriol (A‐E2) were produced. For A‐E1, the limit detection of estrone was 0.04 µg/l and for A‐E2 were 0.07, 0.04 and 0.2 µg/l of estrone, estradiol and estriol, respectively. Different river water samples were analyzed by ELISA and HPLC method.     

PLS Regression in the Spectrophotometric Data for the Simultaneous Determination of Levodopa and Carbidopa in Pharmaceutical Preparations by Using an Enzymatic Stopped‐Flow FIA Technique

Abstract

An enzymatic stopped‐flow‐injection analysis is proposed for simultaneous determination of levodopa and carbidopa in pharmaceutical preparations. The dopaquinones obtained after the oxidation catalized by the enzyme were measured by spectrophotometric method. A reduced calibration matrix based on a central composite experimental design was built and Partial Least Squares (PLS) was applied on the spectral data after reaction with the enzyme. The LOD was 0.015 and 0.0028 mg ml^?1, respectively and the sample throughput was 22.5 h^?1. The proposed method was applied to pharmaceutical preparations and the results are in close agreement with pharmacopeial method. The recovery study and results were satisfactory.     

A Solid‐phase Spectrophotofluorimetry for the Determination of Trace Amount of Nitrite in Food Samples with Rhodamine B

Abstract

A simple and sensitive solid‐phase fluorescence quenching method for the determination of trace amounts of nitrite in food samples has been developed. The method is based on that rhodamine B (RhB) which is used as an emission reagent and is included by β‐cyclodextrin polymer(β‐CDP), reacts with nitrite in the presence of iodide to form a nonfluorescence compound in acidic medium. The fluorescence intensity of the RhB‐included β‐CDP was measured in solid phase with excitation and emission wavelengths of 353 and 592 nm, respectively. The fluorescence quenching degree is good linear with the concentration of nitrite over the ranges of 1.0–3.0 µg with a detection limit of 0.04 µg and RSD is 1.2%. The general coexisting ions do not interfere to the reaction of RhB with nitrite. The proposed method has been applied to the determination of trace amount of nitrite in food samples with the recoveries of 102.8% (ham) and 99.0% (sausage), respectively.     

Determination of Chlorfenvinphos in Soils by Microwave‐Assisted Extraction and Stripping Voltammetry with an Ultramicroelectrode

Abstract

A methodology for the determination of the pesticide chlorfenvinphos by microwave‐assisted solvent extraction and square‐wave cathodic stripping voltammetry at a mercury film ultramicroelectrode in soil samples is proposed. Optimization of microwave solvent extraction performed with two soils, selected for having significantly different properties, indicated that the optimum solvent for extracting chlorfenvinphos is hexane‐acetone (1∶1, v/v). The voltammetric procedure is based on controlled adsorptive accumulation of the insecticide at the potential of?0.60 V (vs. Ag/AgCl) in the presence of Britton‐Robinson buffer (pH 6.2). The detection limit obtained for a 10 s collection time was 3.0×10^?8 mol l^?1. The validity of the developed methodology was assessed by recovery experiments at the 0.100 µg g^?1 level. The average recoveries and standard deviations for the global procedure reached by MASE‐square‐wave voltammetry were 90.2±2.8% and 92.1±3.4% for type I (soil rich in organic matter) and type II (sandy soil) samples, respectively. These results are in accordance to the expected values which show that the method has a good accuracy.     

Solid‐Phase Microextraction Followed by High‐Performance Liquid Chromatography with Fluorimetric and UV Detection for the Determination of Polycyclic Aromatic Hydrocarbons in Water

Abstract

We have developed a solid‐phase microextraction procedure for polycyclic aromatic hydrocarbons. A simplex experimental design was employed to optimize the process. A polydimethylsiloxane/divinylbenzene fiber was selected. The optimum conditions were: an extraction step in the immersion mode, over a period of 60 min at 70°C using high‐speed stirring, and an 8 min desorption step using acetonitrile (90 µl). Linear relationships were obtained for all compounds, except for naphthalene. Our method showed a good precision and accuracy with a detection limit between 0.005 and 0.306 µg l^?1. Our method was used to detect PAHs in real water samples.     

Spectrophotometric Determination of Gold in Water and Ore with 2‐Carboxyl‐1‐Naphthalthiorhodanine

Abstract

This paper reports on the synthesis of a new chromogenic reagent, 2‐carboxyl‐1‐naphthalthiorhodanine (CNTR). A high sensitive, selective, and rapid method for the determination of gold based on the rapid reaction of gold with CNTR and the solid phase extraction of the colored chelate with a reversed phase polymer‐based C₁₈ cartridge was developed. In the presence of 0.05–0.5 mol L^?1 of phosphoric acid solution and emulsifier‐OP medium, CNTR reacts with gold to form a red chelate of a molar ratio 1∶3 (gold to CNTR). This chelate was enriched by the solid phase extraction with a polymer‐based C₁₈ cartridge and the retained chelate was eluted from the cartridge with dimethyl formamide (DMF). The enrichment factor of 100 was achieved. In the DMF medium, the molar absorptivity of the chelate is 1.35×10⁵ L · mol^?1 · cm^?1 at 540 nm. Beer's law is obeyed in the range of 0.01～2 µg mL^?1 in the measured solution. The relative standard deviation for 11 replicates sample of 0.5 µg L^?1 level is 2.05%. The detection limit, based on three times the standard deviation is 0.02 µg L^?1 in the original sample. This method was applied to the determination of gold in water and ore with good results.     

Simultaneous Determination of Fluvoxamine and Its Metabolites in Human Liver Microsomes by High‐Performance Liquid Chromatography with Solid‐Phase Extraction

Abstract

A simple and sensitive high‐performance liquid chromatography method was developed for the simultaneous quantitative determination of fluvoxamine and its two metabolites, fluvoxamino alcohol and fluvoxamino acid, in human liver microsomes. Chromatographic separation was achieved with a Grand‐pak C4‐5 column using a mobile phase at pH 2.5 of 0.5% KH₂PO₄‐acetonitrile (75:25, v/v). Analysis involved a solid‐phase extraction with an Oasis HLB cartridge, which gave high extraction recovery (>92.8%) with good selectivity. The lower limit of quantification of this assay was 78.6 nM for fluvoxamine and fluvoxamino acid, and 82.2 nM for fluvoxamino alcohol, respectively. The coefficient of variation of intra‐ and interday assays was less than 5.8% and accuracy was within 5.3% for all analytes (concentration range 78.6 nM–2.36 µM for fluvoxamine and fluvoxamino acid, and 82.2 nM–2.47 µM for fluvoxamino alcohol, respectively). This method is applicable for accurate and simultaneous determination of oxidative metabolites of fluvoxamine by human liver microsomes.     

Flow‐Injection Spectrophotometric Determination of N‐acetylcysteine in Pharmaceutical Formulations with On‐Line Solid‐Phase Reactor Containing Zn(II) Phosphate Immobilized in a Polyester Resin

Abstract

A flow‐injection spectrophotometric procedure was developed for determining N‐acetylcysteine in pharmaceutical formulations. The sample was dissolved in deionized water and 400 µl of the solution was injected into a carrier stream of 1.0×10^?2 mol l^?1 sodium borate solution. The sample flowed through a column (70 mm length×2.0 mm i.d.) packed with Zn₃(PO₄)₂ immobilized in a polymeric matrix of polyester resin and Zn(II) ions were released from the solid‐phase reactor because of the formation of the Zn(II) (N‐acetylcysteine)₂ complex. The mixture merged with a stream of borate buffer solution (pH 9.0) containing 5.0×10^?4 mol l^?1 Alizarin red S and the Zn(II)Alizarin red complex formed was measured spectrophotometrically at 540 nm. The analytical curve was linear in the N‐acetylcysteine concentration range from 3.0×10^?5 to 1.5×10^?4 mol l^?1 (4.9 to 24.5 µg ml^?1) with a detections limit of 8.0×10^?6 mol l^?1 (1.3 µg ml^?1). The relative standard deviations (RSDs) were smaller than 0.5% (n=10) for solutions containing 5.0×10^?5 mol l^?1 (8.0 µg ml^?1) and 8.0×10^?5 mol l^?1 (13.0 µg ml^?1) of N‐acetylcysteine, and the analytical frequency was 60 determinations per hour. A paired t‐test showed that all results obtained for N‐acetylcysteine in commercial formulations using the proposed flow‐injection procedure and a comparative procedure agreed at the 95% confidence level.     

Electrochemical Determination of Epinephrine with a Pyrolytic Graphite Electrode in the Presence of Ascorbic Acid and Dopamine

Epinephrine (EP) is one of the most important neurotransmitters in mammalian central nervous systems, existing in the nervous tissue and body fluid in the form of large organic cations, and controlling the nervous system in the series of biological perfor…     

Procaine as a Sensing Material for Determination of Dysprosium(III) Ions in Presence of Other Rare‐earth Elements in Biological and Environmental Samples

Abstract

The biological properties of the lanthanides, primarily based on their similarity to calcium, have been the basis for research into potential therapeutic applications of lanthanides since the early part of the twentieth century. In this research, procaine was used as a sensing material in construction of a new Dy(III) potentiometric membrane sensor. The sensor exhibits a Nernstian response over a concentration range of 1.0×10^?6 mol l^?1?1.0×10^?1 mol l^?1, with a detection limit of 7.9×10^?7 mol L^?1. The best performance was achieved with a membrane composition, consisting of 30% PVC, 63% dibutylphthalate (DBP), 5% procaine and 2% sodium tetraphenylborate (NaTPB). It was found that at the pH range of 4.0–8.0, the potential response of the sensor was not affected by the pH. Furthermore, the electrode presents satisfactory reproducibility, very fast response time (<10 s) and relatively good discriminating ability for Dy(III) ions with respect to many common cations and other lanthanide ions. The sensor has been applied to the determination of Dy(III) in human serum and in soil and sediment samples. Validation with Certified Reference Material (CRM) was also done.     

Improved Synthesis of 1‐Benzenesulfinyl Piperidine and Analogs for the Activation of Thioglycosides in Conjunction with Trifluoromethanesulfonic Anhydride*

An improved protocol for the large‐scale production of 1‐benzenesulfinyl piperidine and other sulfinamides is described. It is demonstrated that 1‐benzenesulfinyl pyrrolidine and N,N‐diethyl benzenesulfinamide function analogously to 1‐benzenesulfinyl piperidine in the trifluoromethanesulfonic anhydride‐mediated activation of thioglycosides, and that their less crystalline nature enables them to be used at ?78°C as opposed to the ?60°C required to keep 1‐benzenesulfinyl piperidine in solution. N,N-Dicyclohexyl benzenesulfinamide does not activate thioglycosides in combination with trifluoromethanesulfonic anhydride, which is attributed to its greater steric bulk.     

Determination of the Herbicide Fluometuron by Photo‐induced Chemiluminescence in a Continuous‐flow Multicommutation Assembly

Abstract

This study was dealing with the chemiluminometric determination of the selective herbicide Fluometuron or 1,1‐dimethyl‐3‐(α,α,α‐trifluoro‐m‐tolyl)urea, (C₁₀H₁₁F₃N₂O) with a molecular weight 232.29 belongs to the phenyl urea herbicides family. The analytical strategy is based on the continuous‐flow manifold, multicommutation and the analyte pre‐treatment, the photo‐degradation.

The optimization of chemical (pH, medium, temperature, and organized media) and hydrodynamic parameters (volume of reagents and flow rate) was performed by univariant and multiparametric simplex procedure respectively. Analytical figures of merit and the effect of foreign substances were studied. The method resulted in quick, automated cost‐effective and clean procedure to determine the herbicide in spiked different samples of water and a formulation.     

Solid Phase Extraction of Trace Metals in Seawater Using Morpholine Dithiocarbamate‐Loaded Amberlite XAD‐4 and Determination by ICP‐AES

Abstract

Application of morpholine dithiocarbamate (MDTC) coated Amberlite XAD‐4, for preconcentration of Cu(II), Cd(II), Zn(II), Pb(II), Ni(II) and Mn(II) by solid phase extraction and determination by inductively coupled plasma (ICP) atomic emission spectrometry (AES) was studied. The optimum pH values for quantitative sorption of Cu(II), Cd(II), Zn(II), Pb(II), Ni(II), and Mn(II) were 6.5–8.0, 7.0–8.5, 6.0–8.5, 6.5–8.5, 7.5–9.0, and 8.0–8.5, respectively. The metals were desorbed with 2 mol L^?1. The t_1/2 values for sorption of metal ions were 2.6, 2.9, 2.5, 2.6, 3.0, and 3.8 min respectively for Cu(II), Cd(II), Zn(II), Pb(II), Ni(II) and Mn(II). The effect of diverse ions on the determination of the previously named metals was studied. Simultaneous enrichment of the six metals was accomplished, and the method was applied for use in the determination of trace metal ions in seawater samples.     

Matrix Effects in Determination of Triazines and Atrazine Metabolite in Waters with Solid‐Phase Extraction Followed by High Performance Liquid Chromatography Coupled with Tandem Mass Spectrometry

Abstract

A method for determination of selected triazines in waters was developed. The method includes off‐line solid‐phase extraction of triazines on the polymeric sorbent, high‐pressure liquid chromatographic separation, and determination with tandem mass spectrometer. The linearity extended from 0.008 to 1.000 µg L^?1 for each triazine while the limits of detection ranged from 0.001 to 0.004 µg L^?1. Solid‐phase extraction recoveries from ground, surface, and waste waters ranged from 64% to 96%. Possible water interferences were investigated. Natural humic acids and salts did not influence the ionization process. The presence of humic acids did not affect binding ability of the solid‐phase sorbent, while the presence of salts increased the extraction efficiency by approximately 10%.     

Simultaneous Spectrofluorimetric Determination of Paracetamol and Caffeine in Pharmaceutical Preparations in Solid‐Phase Using Partial Least Squares Multivariate Calibration

Abstract

Partial least‐squares algorithm (PLS)‐1 was used for the solid‐phase spectrofluorimetric determination of paracetamol (PA) and caffeine (CF) in pharmaceutical formulations. In despite of the closely overlapping spectral bands, the method allows the simultaneous quantification and sample preparation prior to analysis is not required. The calibration set consisted of 96 samples with 100–400 mg/g^?1 PA plus 10–65 mg/g^?1 CF; another set of 25 samples was used for external validation. Agreement between predicted and experimental concentrations was fair (r=0.993 and 0.964 for PA and CF models). Prediction performance was evaluated in terms of the coefficient of variability (CV), relative predictive determination (RPD), and ratio error range (RER). The PLS‐1 model was used for the determination of PA and CF in pharmaceutical formulations.     

Determination of BTEX Compounds in Solid–Liquid Mixing Paint Using the Combination of Solid Phase Extraction,Thermal Desorption and GC-FID

A novel method was developed and validated for determination of benzene, toluene, p-xylene, m-xylene, o-xylene (BTEX) in a solid–liquid mixing matrix. It makes use of solid phase extraction and thermal desorption (SPE-TD), followed by gas chromatographic flame ionization detector analysis (GC-FID). The trapped BTEX can be measured directly after thermal desorption onto the stainless-steel packed chromatographic column. The effect of tailing area of solvent was removed with the use of SPE-TD technique, and the result shows good reproducibility with very little matrix dependency. The study also supports that the lifetime of the Tenax adsorption tube could be extended over 150 desorption operation at 200 °C, which enables performing excellent stability and reproducibility of BTEX analysis.

     

Simultaneous Determination of Cephradine,L‐Arginine,and Cephalexin in Cephradine for Injection by Capillary Zone Electrophoresis

Abstract

Applying capillary zone electrophoresis (CZE) to separate the components of Cephradine for Injection: cephradine, and L‐arginine, as well as cephalexin, which is the degradation product of cephradine was studied. The best results were achieved with background electrolyte consisting of 50 mM disodium hydrogen phosphate buffer at pH 6.5 and an applied voltage of 20 kV in a bare fused‐silica capillary. The samples were injected at 50 mbar for 4 s. The capillary temperature was 25°C and the UV detection was performed at a wavelength of 195 nm. Histidine was used as internal standard (IS) to ensure acceptable precision data. The linear ranges of cephradine, L‐arginine, and cephalexin were 93.8–6255.6 µg/mL, 47.9–3195.2 µg/mL, and 6.1–405.4 µg/mL, respectively. Quantitative parameters such as accuracy, precision, limit of detection (LOD), and limit of quantitation(LOQ) were all established in CZE mode.     

A Dip‐and‐Read Test Strip for the Determination of Nitrite in Food Samples for the Field Screening

Abstract

A new test strip method for field screening of nitrite in aqueous samples based on the diazo‐coupling reaction between the nitrite and the Griess reagents has been developed. The test strip has a circular sensing zone that contains two layers: the Griess reagents act as the sensing reagent and is immobilized in the bottom layer; the top layer is a cellulose acetate membrane that can be used as a dialysis membrane to remove the matrix from the sample, which can enhance the selectivity of this method. When the test strip was directly dipped into the samples, a color change of the test strip was observed, and the intensity of color that appears on the test strip is proportional to the concentration of nitrite in the range from 0.50 to 25 µg mL^?1 in food samples. Under the experimental conditions, as low as 0.20 µg mL^?1 nitrite can be observed; most of anionic and cationic species as well as other sample matrixes basically do not interfere with the nitrite measurement.     

Solid‐Solid Phase and Solvent‐Free Oxidative Removal of N‐(4‐Alkoxyphenyl) Groups of Monocyclic β‐Lactams with Ceric Ammonium Nitrate as a Cheap,Simple, and Efficient Method

Five N‐(4‐methoxyphenyl)‐ and five N‐(4‐ethoxyphenyl)‐β‐lactams were prepared by ketene‐imine [2+2] cycloaddition (Staudinger reaction). Then these 2‐azetidinones were N‐dearylated by grinding together with ceric ammonium nitrate without hazardous solvents in good to excellent yields. The solid‐solid phase N‐dearylation is easier, simpler, and more efficient than the general method in solution. The pure N‐unsubstituted β‐lactams obtained by a nontedious workup and without further purification.