Determination of Molybdenum(VI) At Trace Levels by a Catalytic Polarographic Method

Abstract

ARSTRACT

A d.c. polarography method for molybdenum (VI) determination at trace levels has been developed. The reaction is catalytic between molybdenum, salicylaldoxime (SCAD) and bromate in acetic-acetate medium. The obtained peak is proportional to molybdenum (VI) concentrations in the range 1.08.10^?a to 1.37.10^?6 M. The proposed procedure is selective, the most serious interferents being W(VI), Pb(II) and Fe(II). It is applied to molybdenum determination in steel samples after iron extraction by ethyl ether.     

Extraction,Spectrophotometric and Atomic Absorption Spectrophotometric Determination of Molybdenum with Caffeic Acid and Application in High Purity Grade Steel and Environmental Samples

Abstract

A new selective and sensitive method for extraction of yellow Mo (VI)-caffeic acid complex with a liquid ion exchanger, Aliquat 336 from 4.0 pH, and spectrophotometric determination of molybdenum in trace amounts is described. the molar absorptivity of the complex is 1.1 × 10⁵ 1 mol^?1 cm^?1 at 340 nm and the colour system obeys Beer's law in the range 0.04–0.99 ppm of Mo(VI). the molybdenum is also determined with AAS and the method is applied for its determination in steel and environmental samples.     

Kinetic-Spectrophotometric Determination of Molybdenum(VI) Based on Its Catalytic Effect on the Thionine-Hydrazine Reaction

Abstract

A kinetic method for the determination of trace amounts of Mo(VI) (0.05-4 μg ml^?1) based on its catalytic effect on the reduction of thionine by hydrazine monochloride in strongly acidic media is reported. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of thionine at 605 nm after a fixed time (5 min.). The detection limit of the method is 23 ng ml^?1 and the relative standard deviation (RSD) for 0.05 μg ml^?1 of Mo(VI) is 1.2% (n=7). The method is almost free from interferences, especially from large amounts of tungsten. The procedure was successfully applied to the determination of trace amounts of molybdenum in steel.     

Letter to the Editor

Abstract

The experiments show that Mo(VI) has very strong catalytic effect on the slow redox reaction between methyl orange and hydrazine sulfate in sulphuric acid medium at 100°C. And methyl orange exhibits a sensitive second derivative wave at ?0.72 V vs. SCE in the supporting electrolyte of NaOH. This provides a novel catalytic method for the determination of trace amounts of molybdenum using linear scan voltammetry as detection technique. A Calibration graph from 1 to 80 ng/ml and detection limit of 0.3 ng/ml Mo were obtained by the fixed-reaction time procedure. This new catalytic method has been applied to determining molybdenum in ore and standard steel samples, with excellent results.     

A New Method for the Microdetermination of Molybdenum (VI) in Steel,Biological Materials and Waters

Abstract

A method is presented for the trace analysis of molybdenum (VI) in standard steel sample, plant tissues, animal tissues, and natural waters. The method is based on the extractive separation of molybdenum from complex matrices by chelating it with a new reagent N-p-methoxypheny1-2-furylacrylohydroxamic acid (MFHA) into isoamyl alcohol followed by spectrophotometric determination, Eight other new hydroxamic acids were studied for the same purpose and MFHA was chosen as it was the most sensitive of these as well as the other hydroxamic acids reported previously, The method enables rapid and reliable analysis of molybdenum at ppb lelvels in environmental matrices.     

Triphenyltetrazolium chloride as a new analytical reagent for molybdenum(VI): Application to plant analysis

Solvent extraction of molybdenum(VI) ion associate with triphenyltetrazolium chloride (TTC) has been studied. TTC was proposed as reagent for the spectrophotometric determination of micro amounts of molybdenum(VI) at λ_max 250 nm. The optimum conditions for extraction of molybdenum(VI) as an ionassociation complex with TTC has been determined. Beer’s law is obeyed in the range of 0.5–10 μg/mL molybdenum(VI). The molar absorptivity of the ion-pair is 1 × 10⁶ L/mol cm. The sensitivity of the method is 9.6 × 10⁻⁵ μg/cm². The characteristic values for the extraction equilibrium and the equilibrium in the aqueous phase are: distribution constant K _D = 32.64, extraction constant K _ex = 2.19 × 10¹⁰ association constant β = 6.71 × 10⁸. The interferences of different cations, anions on molybdenum(VI) determination were also investigated. A sensitive and selective method for the determination of microquantities of molybdenum(VI) has been developed. The determination was carried out without preliminary separation of molybdenum. A novel procedure of molybdenum(VI) extraction and spectrophotometric determination in different plant samples was examined.     

Simultaneous kinetic determination of phosphate and silicate based on heteropoly blue formation

Small amounts of phosphate (0.08–1.16 μg ml^-1) and larger amounts of silicate (12–60 μg ml^-1) can be determined simultaneously by a kinetic method based on the difference in the rates of the heteropoly blue formation with molybdenum (V)—molybdenum (VI) mixtures in 0.28 M perchloric acid. The interference of large amounts of iron(III) on the determination of phosphate can be eliminated by masking with sodium hydrogen sulfite; this method is applicable to reagent-grade iron(III) chloride.     

Novel Reaction for Rapid,Simple, and Sensitive Determination of Molybdenum in Various Samples

Abstract

A new sensitive, selective, rapid, and reproducible method is presented for the analysis of trace amounts of molybdenum (VI) (Mo(VI)). The method is based on the reaction of molybdenum (VI) with a new analytical reagent, 6‐(5‐Chloro‐2‐hydroxy‐4‐sulfophenylazo)‐5‐hydroxy‐1‐naphthalenesulfonic acid, disodium salt. Under optimum reaction conditions, molybdenum (VI) forms a red complex with a maximum absorption peak at 589 nm. The color reaction is rapidly completed at room temperature. The apparent molar absorption coefficient and Sandell sensitivity were 1.13×10⁴ L · mol^?1 · cm^?1 and 0.0084 µg · cm^?2, respectively. Beer's law was obeyed up to 8.5 µg · mL^?1. Methods for the determination of Mo(VI) by first‐derivative spectrophtometry have also been proposed at 547 and 625 nm. The proposed methods offer the advantages of sensitivity, rapidity, selectivity, and simplicity without any prior separation or extraction. The methods have been applied to the determination of Mo(VI) in various environmental samples and some alloys; satisfactory results have been obtained.     

Catalytic spectrophotometric determination of molybdenum (VI) with the hydrazine-metanil yellow system

A new catalytic Spectrophotometric method for the determination of trace amounts of molybdenum (VI) has been proposed. The method is based on the catalytic effect of Mo(VI) on the reduction of metanil yellow by hydrazine dihydrochloride. Under experiment condition, the linear range of determination is 20–160 ng/mL for molybdenum and the detection limit is 11.2ng/mL. The method has been used to determine trace molybdenum in bean samples with the recovery of 96.0–99.0%, with relative standard deviations of 1.50–2.53%.     

Indirect spectrophotometric determination of silicate

An indirect spectrophotometric method has been developed for trace determination of silicate in aqueous samples. The silicate is converted into silicomolybdic acid and extracted into a mixture of 1-butanol and butyl acetate. The silicomolybdic acid is then decomposed with sodium hydroxide and the molybdenum(VI) reduced to molybdenum(III) with a Jones reductor, followed by reoxidation to molybdenum(VI) with iron(III). The resulting iron(II) is complexed with ferrozine, and the absorbance of the complex measured at 562 run. In this manner, submicroamounts of silicate can be determined.     

Kinetic spectrophotometric determination of traces of molybdenum(VI) by its inhibitory effect on the oxidation of 4-hydroxycoumarine by potassium permanganate.

The present paper describes a simple, selective and sensitive kinetic method for the determination of trace amounts of molybdenum(VI) based on its inhibitory effect on the reaction oxidation of 4-hydroxycoumarine by KMnO(4) in the presence of hydrochloric acid, at pH 1.75 at 25 degrees C. The rate of the indicator reaction was followed spectrophotometrically by measuring the decrease in the absorbance of KMnO(4) at 525 nm. The development method includes optimization of the reagent concentration and temperature. The calibration graph was linear in the range of concentrations from 20 to 200 ng/cm(3) of molybdenum(VI). The probable relative error was in the interval 3.10 - 10.52% for the concentration range of 200 - 20 ng/cm(3) molybdenum(VI), respectively. The interference effects of the foreign ions were determined to assess the selectivity of the method. The developed method was found to have relatively good selectivity, sensitivity, simplicity and rapidity. The proposed method was applied to the determination of molybdenum(VI) in a particular type of steel and alloy (hastelloy).     

Molybdenum determination in iron matrices by ICP-AES after separation and preconcentration using polyurethane foam

A procedure is proposed for the separation and determination of molybdenum in iron matrices by a batch process. It is based on the solid-phase extraction of the molybdenum(V) ion as thiocyanate complex on polyurethane (PU) foam. The extraction parameters were optimized. Using 0.20 mol L^–1 hydrochloric acid, a thiocyanate concentration of 0.10 mol L^–1, 100 mg of polyurethane foam and shaking time of 10 min, molybdenum (5–400 μg) can be separated and preconcentrated from large amounts of iron (10 mg). Desorption was carried out instantaneously by conc. nitric acid or acetone. Distribution coefficients, sorption capacity of the PU foam and coefficients of variation were also evaluated. The effect of some ions on the separation procedure was assessed. Iron(III) should be reduced to iron(II). The proposed procedure was used to determine molybdenum in standard iron matrices such as steel and pure iron. The achieved results did not show significant differences with certified values.     

Determination of traces molybdenum by catalytic adsorptive stripping voltammetry

A reliable and very sensitive procedure for the determination of ultra trace of molybdenum is proposed. Molybdenum was determined by cathodic stripping differential pulse voltammetry based on the adsorption collection of the Mo(VI)-Tiron complex on a hanging mercury drop electrode (HMDE). The variation of peak current with pH, concentration of Tiron and chlorate, plus several instrumental parameters such as accumulation time, accumulation potential and scan rate, were optimized. Under optimized condition, the relationship between the peak current and molybdenum concentration is linear in the range of 0.010-21.0 ng ml⁻¹. The limit of detection was found to be 0.006 ng ml⁻¹. The relative standard deviation for 10 replicates determination of 0.6 and 10 ng ml⁻¹ Mo(VI) is equal to 1.3 and 0.9%, respectively. The method was applied to the determination of molybdenum in river water, tap water, well water, plant foodstuff samples such as cucumber, tomato, carrot, and certified steel reference materials.     

Gravimetric determination of molybdenum and its separation from other metals with n-benzoylphenylhydroxylamine

N-Benzoylphenylhydroxylamine is employed as a precipitant for the determination of molybdenum (VI). The precipitate can be weighed either directly or as molybdenum trioxide after ignition. Molybdenum can be determined in the presence of appreciable amounts of iron(III), cobalt(II), copper(II), chromium(VI) and vanadium (V).     

Enhanced sensitivity for the differential pulse polarographic determination of Mo(VI) based on adsorption catalytic current

A differential pulse polarographic (DPP) method based on the adsorption catalytic current in a medium containing chlorate and 8-hydroxyquinoline (oxine) is suggested for the determination of molybdenum(VI). Experimental conditions such as pH and the composition of supporting electrolyte have been optimized to get a linear calibration graph at trace levels of Mo(VI). The sensitivity for molybdenum can be considerably enhanced by this method. The influence of possible interferences on the catalytic current has been investigated. The sensitivity of the method is compared with those obtained for other DPP methods for molybdenum. A detection limit of 1.0 × 10^–8 mol/L has been found.     

Polarographic Determination of Thorium at Trace Level

Abstract

An indirect method has been developed For the determination of thorium(IV) at trace level, by means of the Formation of 11-molybdothorophosphoric acid, its isolation with an organic solvent, stripping with alkali and measurement of the molybdenum(VI) by its catalytic effect on the polarographic reduction of hydrogen peroxide. A detection limit of 0.067 mg/l can be achieved.     

Determination of Manganese (II) in Foodstuffs by β-Cyclodextrin Polymer Phase Spectrophotometry with 1-(2-Pyridylazo)-2-naphthol

The chromogenic agent, 1-(2-pyridylazo)-2-naphthol (PAN) was included in g -Cyclodextrin polymer ( g -CDP) and the modified polymer of inclusion of PAN ( g -CDP-PAN) was obtained. Based on the fact that g -CDP-PAN can adsorb Mn (II) in solution to form Mn (II)-PAN complex, a sensitive and selective solid phase spectrophotometric method for the determination of trace amounts of Mn (II) has been developed. The maximum absorbance of Mn (II)-PAN complex in g -CDP was at 514 nm. The working range of the calibration graph was 2-12 w g of Mn (II). The interference of molybdenum, lead, cobalt, chromium, iron, nickel, zinc, tin, cadmium, and copper that form colored species with PAN in the polymer phase was investigated. The method was applied to the determination of Mn (II) in black rice and tea samples. A new method for the determination of trace amounts of manganese by polymer phase spectrophotometry is described. Manganese reacted with 1-(2-pyridylazo)-2-naphthol (PAN) that was included in a g -cyclodextrin polymer. The absorbance of the colored polymer, packed into a 5 mm quartz cell, was determined directly at 514 nm. The proposed method was applied to the determination of manganese in black rice and tea samples.     

液膜分离富集、测定痕量钼

用乳状液膜体系对钼进行富集。该体系包括载体 ( 5,8-二乙基 - 7-羟基十二烷 - 6-单肟 ,简称LIX63)、表面活性剂 (N1 1 3C)、溶剂(煤油 )以及内相 ( 0 .1 5mol/LNaOH溶液 )。研究了乳状液膜的稳定性、温度、钼的浓度、外相的HNO3溶液浓度及乳水比等因素对分离富集钼的影响。实验表明 ,在适宜的条件下 ,钼的迁移率可达 99.5%～1 0 0 .2 %。该法已应用于富集、测定纯钨和钢铁中的痕量钼 ,结果相当满意     

Ultraviolet spectrophotometric determination of tungsten(VI) with ammonium 1-pyrrolidinecarbodithioate

A simple and rapid ultraviolet spectrophotometric method is proposed for the determination of trace amounts of tungsten(VI) with ammonium 1-pyrrolidinecarbodithioate (APDC). The method is based on measurement of the absorbance of the tungsten APDC complex in fairly concentrated hydrochloric acid medium; no extraction is required. The complex is formed at an initial acidity of 6M hydrochloric acid and has an absorption maximum at 250 nm. The high absorption of the reagent blank at 250 nm disappears on decomposition of excess of reagent by heating. Beer's law is obeyed over the range 0.43–3.2 ppm of tungsten(VI). The molar absorptivity of the complex is 4.5 × 10⁴ l.mole⁻¹ .cm⁻¹ at 250 nm. Tenfold amounts of aluminium, magnesium, calcium, cobalt, iron(II), lead, silver, sodium and titanium do not interfere in the determination of 50 μg of tungsten (VI).     

Spectrophotometric determination of molybdenum based on charge transfer complexes sensitized by copper(II)

A new high sensitive spectrophotometric determination of trace molybdenum was investigated. The sensitivity of the determination of molybdenum, which based on the color charge transfer complex of molybdotungstophosphate-3,3′,5,5′-tetramethylbenzidine, was greatly enhanced by copper(II) ions in the presence of polyvinyl alcohol. The improved method maintained the features of simplicity, rapidity and selectivity, especially eliminating the interference from tungsten. Under the optimum conditions, Beer's law was obeyed over the range from 2 to 32 ng ml⁻¹ molybdenum with molar absorptivity being 4.92×10⁵ l mol⁻¹ cm⁻¹ at 660 nm. The relative standard deviation was 1.2% under nine determinations for 16 ng ml⁻¹ Mo(VI). The present method had been applied to the determination of trace molybdenum in tungsten ores with satisfactory results.