Multivariate Analysis for the Classification Differentiation of Brazilian Sugarcane Spirits by Analysis of Organic and Inorganic Compounds

Abstract

Brazilian sugarcane spirits were analyzed to elucidate similarities and dissimilarities by principal component analysis. Nine aldehydes, six alcohols, and six metal cations were identified and quantified. Isobutanol (LD 202.9 µg L^?1), butiraldehyde (0.08–0.5 µg L^?1), ethanol (39–47% v/v), and copper (371–6068 µg L^?1) showed marked similarities, but the concentration levels of n-butanol (1.6–7.3 µg L^?1), sec-butanol (LD 89 µg L^?1), formaldehyde (0.1–0.74 µg L^?1), valeraldehyde (0.04–0.31 µg L^?1), iron (8.6–139.1 µg L^?1), and magnesium (LD 1149 µg L^?1) exhibited differences from samples.     

Determination of Veterinary Pharmaceuticals in Production Wastewater by HPTLC-Videodensitometry

An SPE-HPTLC method for simultaneous identification and quantification of seven pharmaceuticals in production wastewater was optimized and validated. The studied compounds were enrofloxacine, oxytetracycline, trimethoprim, sulfamethazine, sulfadiazine, sulfaguanidine and penicillin G/procaine. The method involves solid-phase extraction on hydrophilic-lipophilic balance cartridges with methanol and HPTLC analysis of extracts on CN modified chromatographic plates followed by videodensitometry at 254 and 366 nm. Optimization of chromatographic separation was performed by systematic variation of the mobile phase composition using genetic algorithm approach and the optimum mobile phase composition for TLC separation was 0.05 M H₂C₂O₄:methanol = 0.81:0.19 (v/v). Linearity of the method was demonstrated in the ranges from 1.5 to 15.0 μg L⁻¹ for enrofloxacine, 100–500 μg L⁻¹ for oxytetracycline, 150–600 μg L⁻¹ for trimethoprim, 300–1100 μg L⁻¹ for sulfaguanidine and 100–400 μg L⁻¹ for sulfamethazine, sulfadiazine and penicillin G/procaine with coefficients of determination higher than 0.991. Mean recoveries ranged from 74.6 to 117.1% and 55.1 to 108.0% for wellspring water and production wastewater, respectively. Only sulfaguanidine showed lower results. The described method has been applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Use of ionic liquid based chitosan as sorbent for preconcentration of fluoroquinolones in milk,egg, fish,bovine, and chicken meat samples by solid phase extraction prior to HPLC determination

The possibility of using ionic liquid based chitosan sorbent for the separation and preconcentration of fluoroquinolone antibiotics (marbofloxacin, enoxacin, ofloxacin, ciprofloxacin, and enrofloxacin) has been studied. For this reason, different ionic liquids were prepared and coated on the chitosan sorbent. The conditions of the preconcentration of fluoroquinolones on a microcolumn have been optimized and the extraction efficiencies of the prepared sorbents have been compared. The compounds were eluted with 5 mL of 20% NH₃ (v/v, MeOH) solution and determined by HPLC with diode array and fluorescence detector. The limits of detection were found as 4.23 µ g L^?1 for marbofloxacin, and 1.09 µg L^?1 for enoxacin; 3.23 × 10^?3 µg L^?1 for ofloxacin; 8.39 × 10^?3 µg L^?1 for ciprofloxacin; and 19.50 × 10^?3 µg L^?1 for enrofloxacin. The developed method was applied for the analysis of fluoroquinolone in milk, egg, fish, bovine, and chicken samples and the recoveries were obtained in the range 70–100%.     

Simple Method for Determination of Lead in Hair Dyes Using Slurry Sampling Graphite Furnace Atomic Absorption Spectrometry

A fast, simple and sensitive method for determining of lead in hair dyes using graphite furnace atomic absorption spectrometry with slurry sampling was developed. Multivariate optimization was used to establish optimal analytical parameters through a fractional factorial and a central composite design. The samples were submitted for direct analysis without prior digestion and were diluted in 2.5% v/v HNO₃ and 1.5% v/v H₂O₂. Palladium (chemical modifier) and rhodium (permanent modifier) were selected from several potential modifiers. The optimal conditions were a pyrolysis time of 10 s (liquid and dust dyes) 20 s (cream dyes), a pyrolysis temperature of 789°C (liquid dyes) or 750°C (cream and dust dyes) and an atomization temperature of 1800°C for all dyes. Under optimum conditions, the calibration graph is linear in the 1.50–50.0 µg L^?1 concentration range, with a detection limit of 0.33, 0.44, and 0.39 µg L^?1 for liquid, dust, and cream hair dyes, respectively. The relative standard deviation ranged from 1.63 to 4.56%. The recovery rate ranged from 85 to 108%, and no significant differences were found between the results obtained with the proposed method and the microwave decomposition analysis method of real samples. The concentration ranges obtained for lead in the hair dyes samples were 1.00–11.3 µg L^?1 for liquid dyes, 14.0–100 µg kg^?1 for dust dyes, and 19.9–187 µg kg^?1 for cream dyes.     

Mercury speciation by a high performance liquid chromatography—atomic fluorescence spectrometry hyphenated system with photo-induced chemical vapour generation reagent in the mobile phase

Speciation of mercury was accomplished by using a simple interface with photo-induced chemical vapour generation in a high performance liquid chromatography—atomic fluorescence spectrometry (HPLC-AFS) hyphenated system. Acetic acid and 2-mercaptoethanol in the mobile phase were used as photochemical reagent. The operating parameters were optimized to give limits of detection of 0.53 µg L^?1, 0.22 µg L^?1, 0.18 µg L^?1 and 0.25 µg L^?1 for inorganic mercury, methylmercury, ethylmercury and phenylmercury, respectively. The method was validated with the certified reference material DORM-2 and applied to the analysis of seafood samples. The HPLC-AFS hyphenated system is simple, environmentally friendly, and represents an attractive alternative to the conventional peroxothiosulfate-borohydride method.     

Square-Wave Anodic Stripping Voltammetry (SWASV) for the Determination of Ecotoxic Metals,Using a Bismuth-Film Electrode

This article reviews the use of square wave anodic stripping voltammetry for the simultaneous determination of ecotoxic metals (Pb, Cd, Cu, and Zn) on a bismuth-film (BiFE) electrode. The BiFE was prepared in situ on a glassy-carbon electrode (GCE) from the 0.1 mol L^?1 acetate buffer solution (pH 4.5) containing 200 µg L^?1 of bismuth (III). The addition of hydrogen peroxide to the electroanalytical cell proved beneficial for the interference-free determination of Cu (II) together with zinc, lead, and cadmium, using the BiFE. The experimental variables were investigated and optimized with the view to apply this type of voltammetric sensor to real samples containing traces of these metals. The performance characteristics, such as reproducibility, decision limit (CC_a), detection capability (CC_β), sensitivity, and accuracy indicated that the method holds promise for trace Cu²⁺, Pb²⁺, Cd²⁺, and Zn²⁺ levels by employment of Hg-free GCE with SWASV. CCa, and CCβ were calculated according to the Commission Decision of 12 August 2002 (2002/657/EC). Linearity was observed in the range 20–280 µg L^?1 for zinc, 10–100 µg L^?1 for lead, 10–80 µg L^?1 for copper, and 5–50 µg L^?1 for cadmium. Using the optimized conditions, the stripping performance of the BiFE was characterized by low limits of detection (LOD). Finally, the method was successfully applied in real as well as in certified reference water samples.     

Selective extraction and preconcentration of ultra-trace amounts of arsenic(V) ions using carbon nanotubes as a novel sorbent

In the present study, multiwalled carbon nanotubes (MWCNTs) as solid phase extraction sorbent were developed for preconcentration of arsenic(V) species prior to graphite furnace atomic absorption spectrometry (GFAAS) determination. Arsenic(V) was selectively sorbed on the packed column with MWCNTs within a pH 9.5 in the presence of 2-(5-bromo-2-pyridylazo)-5-diethyl amino phenol (5-Br-PADAP). The adsorbed species was then desorbed with 1 mL of 2.0 M HNO₃. Experimental parameters including pH, sample volume and flow rate, type, volume and concentration of eluent that influence the recovery of the arsenic(V) species were optimised. Under the optimised conditions, the calibration curve was linear in the range of 0.2–10.0 µg L^?1 with detection limit of 0.016 µg L^?1. The relative standard deviations (RSD) for seven replicate determinations at 1.0 µg L^?1 level of arsenic was 6.69%. The proposed method was successfully applied to the determination of arsenic in water samples and certified reference material (NIST RSM 1643e).     

Trace Determination of Manganese in Urine by Graphite Furnace Atomic Absorption Spectrometry and Inductively Coupled Plasma–Mass Spectrometry

This paper describes a simple and sensitive method for the determination of manganese in human urine by graphite furnace atomic absorption spectroscopy (GFAAS), which includes sample preparation by microwave digestion. Matrix modifier combinations, the digestion power, pyrolysis, and atomization temperatures were optimized. A mixture of 5.0 µg Pd(NO₃)₂ and 3.2 µg Mg(NO₃)₂ modifier presented the best performance. The optimal temperatures for pyrolysis and atomization were 1500°C and 1950°C, respectively. The GFAAS method was compared to inductively coupled plasma–mass spectrometry (ICP–MS) for the determination of manganese in urine. Analytical figures of merit for GFAAS and ICP–MS were: accuracy (3.46%, 2.19%), precision (3.61%, 5.84%), LOD (0.109 µg · L^?1, 0.015 µg · L^?1), LOQ (0.327 µg · L^?1, 0.045 µg · L^?1), and recovery (80–100%, 74–89%). Both methods were employed for the determination of Mn in urine and the results were compared statistically.     

Occurrence of cytostatic compounds in hospital effluents and wastewaters,determined by liquid chromatography coupled to high-resolution mass spectrometry

The occurrence of 26 commonly used cytostatic compounds in wastewaters was evaluated using an automated solid-phase extraction (SPE) method with liquid chromatography–high-resolution mass spectrometry (LC–HRMS). Detection was optimized using Oasis HLB SPE cartridges at pH 2. Two hospital effluents and their two receiving wastewater treatment plants were sampled over five days. In hospital effluents, eight cytostatics were detected at levels up to 86.2 μg L^?1 for ifosfamide, 4.72 μg L^?1 for cyclophosphamide, and 0.73 μg L^?1 for irinotecan, the three most relevant compounds identified. Cyclophosphamide and megestrol acetate were found in wastewaters at concentrations up to 0.22 μg L^?1 for the latter. The predicted environmental concentrations (PEC) in sewage effluents of ifosfamide (2.4–4.3 ng L^?1), capecitabine (11.5–14.2 ng L^?1), and irinotecan (0.4–0.6 ng L^?1), calculated from consumption data in each hospital, published excretion values for the target compounds, and wastewater elimination rates, were in agreement with experimental values.     

Ion Chromatography with Post-column Reaction and Serial Conductivity and Spectrophotometric Detection Method Development for Quantification of Transition Metal Dissolution in Lithium Ion Battery Electrolytes

We present a method for the separation and determination of transition metals in electrolytes based on ion chromatography (IC) with post-column reaction (PCR) and serial conductivity and spectrophotometric detection. Three IC columns [Metrosep C4—250/4.0 (column A), Metrosep C6—250/4.0 (column B), and Nucleosil 100-5SA—250/4.6 (column C)] with different capacities, and stationary phases were used and compared with each other for method development. All spectrophotometric measurements were carried out with 4-(2-pyridylazo)resorcinol (PAR) as PCR reagent at a wavelength of 500 nm. To characterize the precision of the separation, the selectivity for the analysis of transition metals (nickel, cobalt, copper, and manganese) in the presence of large amounts of lithium and the resolution of the peaks were determined and compared with one another. Furthermore, the limits of detection (LOD) and quantification (LOQ) were determined for the transition metals. The LODs and LOQs determined by column C were as follows: cobalt (LOD/LOQ): 9.4 µg L^?1/31.3 µg L^?1, manganese (LOD/LOQ): 7.0 µg L^?1/23.5 µg L^?1, and nickel (LOD/LOQ): 6.3 µg L^?1/21.1 µg L^?1. Finally, the concentration of transition metal dissolution of the cathode material Li₁Ni_1/3Co_1/3Mn_1/3O₂ (NCM) was investigated for different charge cut-off voltages by the developed IC method.     

Synthesis and application of polythiophene-coated Fe3O4 nanoparticles for preconcentration of ultra-trace levels of cadmium in different real samples followed by electrothermal atomic absorption spectrometry

In this research, magnetic Fe₃O₄ nanoparticles were synthesised by co-precipitation method and modified with polythiophene (PT) to produce Fe₃O₄-PT nanoparticles for preconcentration and determination of cadmium (??) ion followed by electrothermal atomic absorption spectrometry. The results of FT-IR spectroscopy, EDX analysis and SEM images show that Fe₃O₄-PT nanoparticles were synthesised successfully. Different parameters such as sample pH, amounts of adsorbent, sample volume, extraction time, type and concentration of eluent and desorption time were completely investigated and optimum conditions were selected.

Under the optimum conditions, the calibration curve was linear in the range of 0.01–0.25 µg L^?1 of cadmium (??). The relative standard deviation was 4.7% (n = 7, 0.10 µg L^?1 Cd²⁺) and limit of detection was 3.30 ng L^?1. The accuracy of the proposed method was verified by the analysis of a certified reference material and spike method. Finally, the proposed method was applied for the determination of ultra-trace levels of cadmium (??) in different water and food samples.     

Dispersive Liquid–Liquid Microextraction of Silver Prior to Determination by Microsample Introduction-Flame Atomic Absorption Spectrometry

Abstract

A new simple and sensitive method has been proposed for rapid determination of trace levels of silver in environmental water samples, using dispersive liquid–liquid microextraction (DLLME) prior to its microsample introduction-flame atomic absorption spectrometry. Under the optimum conditions, the linear range was 0.1–7 µg L^?1 and limit of detection was 0.018 µg L^?1. The relative standard deviation for 0.50 and 5.00 µg L^?1 of silver in water sample was 4.0 and 1.7%, respectively. The relative recoveries of silver from tap, well, river, and seawater samples at spiking levels of 1.00 and 5.00 µg L^?1 were in the range of 86.4–98.6%.     

Determination of trace amounts of nystatin in water and vaccine samples using sodium dodecyl sulfate-coated iron oxide magnetic nanoparticles followed by high-performance liquid chromatography–ultraviolet detection

In this work, magnetic solid-phase extraction based on sodium dodecyl sulfate-coated Fe₃O₄ nanoparticles has been successfully applied for extraction and preconcentration of trace amounts of nystatin from water and vaccine samples prior to high-performance liquid chromatography–ultraviolet detection. Various experimental parameters affecting extraction and recovery of the analyte, such as the amount of sodium dodecyl sulfate, pH of the sample solution, salt concentration, extraction time, sample volume and desorption conditions, were systematically studied and optimized. Under optimized conditions, nystatin was quantitatively extracted. Proper linear range with good coefficient of determination, (R ² > 0.99) and limit of detection and quantification (based on signal-to-noise ratios of 3 and 10) of 2.0 and 5.0 µg L^?1, over the investigated concentration range (5–700 µg L^?1), were obtained, respectively. The intra-day and inter-day relative standard deviations at 50 µg L^?1 level of NYS were 1.4 and 4.5% based on six replicate determinations. The accuracy of the method was evaluated by recovery measurements on spiked samples. Suitable recoveries of 96–102 and 26–44% were achieved (at spiked levels of 50, 300 and 500 µg L^?1) for water and vaccine samples, respectively.     

Determination of Estrogens in Water Samples by Ionic Liquid-Based Dispersive Liquid-Liquid Microextraction Combined with High Performance Liquid Chromatography

Using 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) ionic liquid as extraction solvent, five estrogens including estrone (E₁), 17β-estradiol (E₂), estriol (E₃), 17α -ethynylestradiol (EE₂), and diethylstilbestrol (DES) in water samples were determined by dispersive liquid-liquid microextraction (DLLME) followed by high performance liquid chromatography with a photodiode array detector and a fluorescence detector (HPLC-DAD-FLD). The extraction procedure was induced by the formation of cloudy solution, which was composed of fine drops of [C₆MIM][PF₆] dispersed entirely into the sample solution with the help of a disperser solvent (acetone). Parameters including both extraction and disperser solvents and their volumes, extraction and centrifugal time, sample pH, and salt effect were investigated and optimized. Under the optimized conditions, 110–349 fold enrichment factors of analytes were obtained. The calibration curves were linear in the concentration range of 0.2–100 µg L^?1 for E₂, E₃, and EE₂ detected with FLD, and 1–100 µg L^?1 for E₁ and DES detected with DAD. The correlation coefficient of the calibration curve was between 0.9990 and 0.9997. The limits of detection (LOD, S/N = 3) for the five estrogens were in the range of 0.08–0.5 µg L^?1. The relative standard deviations (RSD) for six replication experiments at the concentration of 5.0 µg L^?1 were ≤5.7%. The proposed method was applied to the analysis of three water samples from different sources (river water, waste water, and sea water). The relative recoveries of spiked water samples are satisfied with 89.3–102.4% and 88.7–105.2% at two different concentration levels of 5.0 and 50.0 µg L^?1, respectively.     

The separation–preconcentration and determination of ultra-trace gold in water and solid samples by dispersive liquid–liquid microextraction using 4-ethyl-1(2-(4-(4-nitrophenyl)piperazin-1-yl)acetyl)thiosemicarbazide) as chelating agent and flame atomic absorption spectrometry

A selective separation and preconcentration method for the determination of gold ions in water and ore samples has been developed using dispersive liquid–liquid microextraction, followed by flame atomic absorption spectrometry. 4-Ethyl-1(2-(4-(4-nitrophenyl)piperazin-1-yl)acetyl)thiosemicarbazide) (NPPTSC) has been used for the first time as new chelating reagent. A mixture of ethanol (dispersive solvent) and carbon tetrachloride (extraction solvent) was used. Some parameters affecting the extraction procedure including the type and volume of the extracting and dispersive solvents, HNO₃ concentration, the chelating agent amount, volume of sample, and foreign ions have optimized. Also, the complex formation between gold ions and the ligand has been investigated in a methanol–water solution (1:1) using UV–visible spectrometry. The spectrophotometric titration data showed that of Au–NPPTSC complex composition was found to be 3:2. After optimizing the instrumental and experimental parameters, we achieved a detection limit of 1.5 µg L^?1, a preconcentration factor of 50, and a linear dynamic range of 10.0–400.0 µg L^?1. The relative standard deviation obtained 2.1% at 50 µg L^?1 for gold ions (n = 10). The proposed method was successfully performed for the determination of gold in certified reference material, environmental water, and ore samples.     

Molecularly imprinted stir bar sorptive extraction coupled with high-performance liquid chromatography for trace analysis of naphthalene sulfonates in seawater

In this paper, a novel molecularly imprinted polymer coated stir bar has been used to selectively extract naphthalene sulfonates (NS_s) directly from seawater sample. 1-Naphthalene sulfonic acid (1-NS) was used as template molecule. The effects of different parameters were optimized on the extraction efficiency and the optimum conditions were established as: the absorption and desorption times were fixed, respectively, at 10 and 15 min, stirring speed was 700 rpm, pH was adjusted to 4.1, amount of NaCl was 1 mol L^?1 and extraction process was performed at a temperature of 50 °C. The linear ranges were 2–250 µg L^?1 for 3,6-NDS-1-OH (1-naphthol-3,6-disulfonic acid), 4–250 µg L^?1 for 2-NS (2-naphthalene sulfonate) and 3–250 µg L^?1 for 1-NS. The detection limits were within the range of 0.32–0.95 µg L^?1. Under optimum conditions, the detection limits of the NSs were 0.84, 0.95 and 0.32 µg L^?1 with the enrichment factor of 117-, 41- and 77-fold for 2-NS, 1-NS, and 6-NDS-1-OH, respectively. The repeatability of the method was satisfactory (0.53 ≤ RSD ≤6.0 %, n = 10). The method has been successfully applied for the analysis of trace amounts of three naphthalene sulfonates in seawater of Chabahar Bay.     

Development of a new analytical method for Pb preconcentration and its further determination in water and foodstuffs using relatively low-sensitivity flame atomic absorption spectrometry

The present study describes chelation of Pb(II) with ascorbic acid and formation of a charge-transfer sensitive ion-pair in the presence of Rhodamine 6G at pH 5.5, and then its extraction to the micellar phase of non-ionic surfactant, PONPE 7.5 by an ultrasound-assisted cloud point extraction method before analysis by FAAS. The various variables affecting ion-pair formation and extraction efficiency were studied and optimised. Under the optimised conditions, the good linear relationships in the ranges of 0.4–150 μg L^?1 and 0.8–120 μg L^?1 for solvent-based calibration and matrix-matched calibration curves, respectively, were achieved with a pre-concentration factor of 71.4 from pre-concentration of 50-mL sample. Moreover, the limits of detection with good sensitivity enhancements of 124 and 114.5 were 0.13 and 0.24 μg L^?1, respectively, while the intra-day and inter-day precision (as RSD%, for five replicate measurements of 5 and 100 μg L^?1 in the same day and three succeed days) were in range of 2.8–5.4% and 3.7–6.3%, respectively. The matrix effect on triplicate determination of 50 µg L^?1 Pb(II) was also investigated. The accuracy of the method was statistically verified by the analysis of two certified reference materials (CRMs) after digestion with acid mixtures (HNO₃-H₂O₂-HF and HNO₃-H₂O₂) and dilution at suitable ratios. It has been observed that there is statistically not a significant difference between the certified- and found-values. The accuracy was also controlled using the pre-treated sample solutions spiked at different concentration levels, and the good spiked recoveries were obtained in range of 90–102.8%. The method was successfully applied to the determination of trace amounts of lead in water and food matrices with satisfactory results.     

Biomethane Production in an AnSBBR Treating Wastewater from Biohydrogen Process

An anaerobic sequencing batch reactor containing immobilized biomass (AnSBBR) was used to produce biomethane by treating the effluent from another AnSBBR used to produce biohydrogen from glucose- (AR-EPHG) and sucrose-based (AR-EPHS) wastewater. In addition, biomethane was also produced from sucrose-based synthetic wastewater (AR-S) in a single AnSBBR to compare the performance of biomethane production in two steps (acidogenic and methanogenic) in relation to a one-step operation. The system was operated at 30 °C and at a fixed stirring rate of 300 rpm. For AR-EPHS treatment, concentrations were 1,000, 2,000, 3,000, and 4,000 mg chemical oxygen demand?(COD)?L^?1 and cycle lengths were 6 and 8 h. The applied volumetric organic loads were 2.15, 4.74, 5.44, and 8.22 g COD L^?1 day^?1. For AR-EPHG treatment, concentration of 4,000 mg COD L^?1 and 4-h cycle length (7.21 g COD L^?1 day^?1) were used. For AR-S treatment, concentration was 4,000 mg COD L^?1 day^?1 and cycle lengths were 8 (7.04 g COD L^?1 day^?1) and 12 h (4.76 g COD L^?1 day^?1). The condition of 8.22 g COD L^?1 day^?1 (AR-EPHS) showed the best performance with respect to the following parameters: applied volumetric organic load of 7.56 g COD L^?1 day^?1, yield between produced methane and removed organic material of 0.016 mol CH₄?g COD^?1, CH₄ content in the produced biogas of 85 %, and molar methane productivity of 127.9 mol CH₄?m^?3 day^?1. In addition, a kinetic study of the process confirmed the trend that, depending on the biodegradability characteristics of the wastewaters used, the two-step treatment (acidogenic for biohydrogen production and methanogenic for biomethane production) has potential advantages over the single-step process.     

Custom-Made C18 Column for Simultaneous Determination of Endocrine Disrupting Substances in Water by Diode-Array and Fluorescence Detectors

A C₁₈ stationary phase was synthesized for a custom-made HPLC column. When compared to a commercial C₁₈ column, better chromatographic performances were obtained. This column was successfully applied for simultaneous determination of p,p′-DDT, o,p′-DDT, benzo(a)anthracene, benzo(b)fluoranthene, and benzo(a)pyrene in waters by high performance liquid chromatography coupled with dual detectors (diode array and fluorescence detectors) combined with solid phase extraction. Low method detection limits were obtained, i.e., p,p′-DDT: 0.5 µg L^?1, o,p′-DDT: 1 µg L^?1, benzo(a)anthracene: 2.5 ng L^?1, benzo(b)fluoranthene: 5 ng L^?1, and benzo(a)pyrene: 2.5 ng L^?1. High recoveries that ranged from 82 to 94% were obtained for all compounds.     

Solvent extraction of Cu,Mo, V,and U from leach solutions of copper ore and flotation tailings

A micro-cloud point extraction method was discussed for preconcentration and spectrophotometric quantification of U(VI). The method depends on complex formation between U(VI) and 2-(4-sulphophenyloazo)-1,8-dihydroxy-3,6-naphtalenedisulphonic acid (SPADNS) at pH 7.0 and subsequent extraction of the complex in a mixed surfactant medium (cethyltrimethyl ammonium bromide and Triton X-114). The separation was carried out in the presence of 1% Na₂SO₄ at room temperature. The calibration curve was linear up to 3000 µg L^?1. The enrichment factor, detection limit and precision were 16.0, 1.05 µg L^?1, and 2.3%, respectively. The method was employed for the determination of U(VI) in real samples with different matrices.