Indirect spectrophotometric determination of chloride by solvent extraction as tris(1,10-phenanthroline)iron(II) thiocyanate

An indirect spectrophotometric method for the determination of small amounts of chloride in fresh waters is described. Chloride ions react with mercury(II) thiocyanate to liberate thiocyanate ions, which can be selectively extracted into nitrobenzene with tris(1,10-phenanthroline)iron(II) chelate cations. The red color (516 nm) of the organic phase measured against a reagent blank is proportional to the initial concentration of chloride ions in the aqueous phase. At least an equimolar amount of tris(1,10-phenanthroline)iron(II) chelate and a 3-fold amount of mercury(II) thiocyanate are needed; the optimal pH range is 1.5–3.5. Beer's law is obeyed over the concentration range of 0.8–5.6 10^-5 M of chloride. The color stability and the apparent sensitivity are better than those of the mercury(II) thiocyanate-iron(III) method. Large amounts of sulphate, phosphate, fluoride, carbonate, acetate, potassium, sodium, and ammonium ions had negligible or no effect ; bromide, iodide, cyanide, sulphide, and thiocyanate interfere.     

Simultaneous Determination of Selenocyanate and Thiocyanate Ions in the Presence of Cyanide by Oxidation with bis (Trifluoroacetoxy) iodobenzene

Abstract

An investigation of the use of potentiometric titrations of selenocyanate and thiocyanate aqueous solutions, in the presence of cyanide ions, with bis (trifluoroacetoxy) iodobenzene in acetonitrile and then the gravimetric determination of the products of the reactions, elemental selenium and sulphate ions, has been carried out.

Selenocyanates are first oxidized to selenium and then thiocyanates are oxidized to sulphate ions. Break point curves are identified. The rose-pink precipitate is filtered and the clear filtrate is warmed on a hot plate for evaporation of acetonitrile. A solution of barium chloride is added to the hot solution in order to precipitate the sulphate ions.     

Crystal structures,selective fluorescent sensing and photocatalytic properties of cobalt(II) and copper(II) coordination architectures with 2,4,5-tri(4-pyridyl)-imidazole

Abstract

Solvothermal reaction of M^II (M?=?Co, Cu) ions with 2,4,5-tri(4-pyridyl)-imidazole (Htpim) gave two MOFs, [Co_1.5(tpim)(FA)₂(H₂O)]_n (1) and [Cu₂(Htpim)(tpim)(FA)(NO₃)₂(DMF)]_n (2) (HFA?=?formic acid, DMF?=?N,N-dimethylformamide). Single-crystal X-ray diffraction analyses indicated that 1 exhibits a 3D {4³.4¹²} topology framework assembled by hexanuclear [Co₆(FA)₈(H₂O)₄] units and tpim ligands, while 2 presents a 2-D double layer {4.6²}₂{4².6⁴.8².10²}{6².8} network. Hereinto, an inorganic acid was not only used to adjust the pH value of reaction system but also to act as an oxidizing agent to participate in in situ organic reactions. Moreover, 1 displays high sensitivity in the detection of nitrobenzene as a fluorescent sensor and exhibits a relatively good photocatalytic activity toward the degradation of rhodamine B in aqueous solution under UV irradiation.     

Solvent Extraction of Pb(II) with AGDOMD

Abstract

The distribution of Pb(II) between an aqueous phase and a toluene phase containing dehydrated fatty acids found in distilled castor oil (AGDOMD) has been studied. Using the slope technique the conditional equilibrium constant of extraction was determined (kext = 1.02 × 10^?7) and the main species present in the organic phase was identified as (PbNO₃R. 2HR)_(o), where HR represents the fatty acid used.     

Color Reaction Between 4-(2-Pyridylazo)Resorcinol and Mercury (II) in the Presence of Surfactant,and Improved Spectrophotometric Determinations of Mercury(II) and Cyanide Ion with its Coloring

Abstract

The reactions among 4-(2-pyridylazo)resorcinol (PAR), mercury(II) and/or cyanide ion in the presence of water soluble surfactants alone or combination were systematically investigated at about pH 9. The spectrophotometric determinations of mercury(II) and cyanide ion were investigated by using the PAR-mercury(II)-HPC complex (3:2:2 molar ratio) in the presence of N-hexadecylpyridinium chloride (HPC) alone; calibration graphs were rectilinear in the ranges of 0 – 40 μg mercury(II) and 0 –10 μg cyanide ion in a final 10 ml with the apparent molar absorptivities of 5.9 × 10⁴ for mercury(II) and 2.5 × 10⁴ 1 mol^?1 cm^?1 for cyanide ion at 590 nm. The proposed method had advantages—rapidity, simplicity without solvent extraction, and sensitivity in comparison with reported solvent extraction methods. The interference of foreign ions decreased 1/2–l//4-fold compared with that in the presence of non-ionic surfactant alone.     

Determination of Iodide and Thiocyanate in Seawater by Liquid Chromatography with Poly(ethylene glycol) Stationary Phase

Novel, simple, rapid, highly sensitive, and direct determination of iodide and thiocyanate ions in seawater has been performed by liquid chromatography (LC) with UV detection at 220 nm. The separation was achieved on a C₃₀ column of conventional size (150 mm × 4.6 mm i.d.) modified with poly(ethylene glycol); an aqueous solution of 300 mM sodium sulfate and 50 mM sodium chloride was used as mobile phase. Detection limits (S/N=3) obtained by injecting a 20-L sample were 0.5 and 6 ng mL^–1 for iodide and thiocyanate, respectively. The method was successfully used for rapid and direct determination of iodide and thiocyanate in seawater samples, collected from the coasts of Japan, without any extra pretreatment.Dedicated to Professor K. Jinno on the occasion of his 60^th birthday     

Bis(2-mercaptobenzoxazolato)mercury(II) and bis(2-pyridinethiolato)mercury(II) complexes as carriers for thiocyanate selective electrodes

Highly selective poly(vinyl chloride) (PVC) membrane electrodes based on bis(2-mercaptobenzoxazolato)mercury(II) [Hg(MBO)₂] and bis(2-pyridinethiolato)mercury(II) [Hg(PT)₂] complexes as new carriers for thiocyanate-selective electrodes are reported. The electrodes were prepared by coating the membrane solution containing PVC, plasticizer, carriers and additives on the surface of graphite electrodes. Influence of the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrodes. Both sensors exhibited Nernstian responses towards thiocyanate over a wide concentration range of 1×10⁻⁶ to 0.1 M, with slopes of 60.6±0.8 and 57.5±1.2 mV per decade of thiocyanate concentration for Hg(MBO)₂ and Hg(PT)₂ carriers, respectively, over a wide pH range of 3-11. The limit of detection for both electrodes was ∼6×10⁻⁷ M. The sensors have response times of ≤5 s and can be used for at least 2 months without any considerable divergence in their potential response. The proposed electrodes show fairly good discrimination of thiocyanate over several inorganic and organic anions. The electrodes were successfully applied to direct determination of thiocyanate in saliva and as indicator electrodes in precipitation titrations.     

Preparation and Spectral Investigation of Bis[N(2-methyl-phenyl) 4-Nitro-thiobenzamidato] mercury(II), Bis[N(2-methoxy-phenyl) 4-Nitro-thiobenzamidato]mercury(II), and Bis[N(2-chloro-phenyl) 4-Nitro-thiobenzamidato]mercury(II) Complexes

Several preparative routes to bis[N(substituted-phenyl) 4-nitro-thiobenzamidato] mercury(II) complexes are presented, including the reaction of mercury(II) oxide, fluoride, chloride, bromide, cyanide, acetate, and nitrate with N(substituted-phenyl) 4-nitro-thiobenzamide derivatives. ¹ H-NMR, Raman, and IR measurements confirmed the complexation of mercury to sulphur.     

Experimental evidence, stability, and the most probable structure of protonated p-tert-butylcalix[4]arenetetrakis(N,N-dimethylacetamide)

Abstract  

From extraction experiments and γ-activity measurements, the extraction constant corresponding to the equilibrium H₃O⁺(aq) + 1·Na⁺(nb) \leftrightarrows \leftrightarrows 1·H₃O⁺ (nb) + Na⁺ (aq) taking place in the two-phase water–nitrobenzene system (1 = p-tert-butylcalix[4]arenetetrakis(N,N-dimethylacetamide); aq = aqueous phase, nb = nitrobenzene phase) was evaluated as log K _ex (H₃O⁺, 1·Na⁺) = −0.1 ± 0.1. Further, the stability constant of the 1·H₃O⁺ complex in water-saturated nitrobenzene was calculated for a temperature of 25 °C as log β _nb (1·H₃O⁺) = 10.9 ± 0.2. By using quantum mechanical DFT calculations, the most probable structure of the 1·H₃O⁺ cationic complex species was derived. In this complex, the hydroxonium ion H₃O⁺ is bound partly to one phenoxy oxygen atom and partly to two carbonyl oxygens of 1 by strong hydrogen bonds and obviously by other electrostatic interactions.     

Some analytical applications of aromatic sulfonyl haloamines: Determination of thiocyanate and cyanide ions in metal complexes and salts with bromamine-B and dichloramine-B

Simple, rapid, and reproducible methods for the determination of thiocyanate and cyanide ions in metal salts and complexes with bromamine-B (BAB) and dichloramine-B (DCB) have been developed. The oxidation involves eight and two electron changes, respectively, with NCS^? and CN^? ions in 0.05–0.20 N NaOH medium in the case of BAB and in partially aqueous medium with DCB. The proposed methods could be employed for computing the number of thiocyanate and cyanide ligands present in the respective metal complexes.     

Synthesis of ammonium [14C]thiocyanate

Ammonium [¹⁴C]thiocyanate was prepared from potassium [¹⁴C]cyanide with a radiochemical yield of 90%. [¹⁴C]hydrocyanic acid, generated from potassium [¹⁴C]cyanide by sulphuric acid, reacts with aqueous ammonia and elemental sulphur in the presence of trace amounts of ammonium sulphide to yield ammonium [¹⁴C]thiocyanate.     

Complexes of Co(II) and Zn(II) with N-(Thio)phosphorylthioureas AdNHC(S)NHP(O)(OiPr)2 and MeNHC(S)NHP(S)(OiPr)2

The reaction of the potassium salt of the N-(thio)phosphorylated thioureas AdNHC(S)NHP(O)(OiPr)₂ (HL^I , Ad = Adamantyl) and MeNHC(S)NHP(S)(OiPr)₂ (HL^II ) with Co(II) and Zn(II) in aqueous EtOH leads to [ML^I,II ₂] chelate complexes. They were investigated by UV-vis, ¹H and ³¹P NMR spectroscopy, and microanalysis. The molecular structures of [ML^I ₂] were elucidated by single crystal X-ray diffraction analysis. The metal centers in both complexes are found to be in a distorted-tetrahedral O₂S₂ environment formed by the C=S sulfur atoms and the P=O oxygen atoms of two deprotonated L^I ligands. The photoluminescence properties of [ZnL^II ₂] are also reported.     

Simultaneous high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS-MS) analysis of cyanide and thiocyanate from swine plasma

An analytical procedure for the simultaneous determination of cyanide and thiocyanate in swine plasma was developed and validated. Cyanide and thiocyanate were simultaneously analyzed by high-performance liquid chromatography tandem mass spectrometry in negative ionization mode after rapid and simple sample preparation. Isotopically labeled internal standards, Na¹³C¹⁵N and NaS¹³C¹⁵N, were mixed with swine plasma (spiked and nonspiked), proteins were precipitated with acetone, the samples were centrifuged, and the supernatant was removed and dried. The dried samples were reconstituted in 10 mM ammonium formate. Cyanide was reacted with naphthalene-2,3-dicarboxaldehyde and taurine to form N-substituted 1-cyano[f]benzoisoindole, while thiocyanate was chemically modified with monobromobimane to form an SCN-bimane product. The method produced dynamic ranges of 0.1–50 and 0.2–50 μM for cyanide and thiocyanate, respectively, with limits of detection of 10 nM for cyanide and 50 nM for thiocyanate. For quality control standards, the precision, as measured by percent relative standard deviation, was below 8 %, and the accuracy was within ±10 % of the nominal concentration. Following validation, the analytical procedure successfully detected cyanide and thiocyanate simultaneously from the plasma of cyanide-exposed swine.     

SYNTHESIS AND STRUCTURES OF DICHLOROTETRAKIS-(PHENYLTHIOUREA) CADMIUM(II) AND CATENA-BIS(THIOCYANATE) BIS(PHENYLTHIOUREA)CADMIUM(II)

Abstract

Two new cadmium(II) complexes with phenylthiourea (PTU), namely Cd(PTU)₄Cl₂ (1) and [Cd₂(NCS)₂(μ₂-SCN)₂(PTU)₂(μ₂-PTU)₂] _n (2), have been prepared and characterized structurally by X-ray diffaction. Complex 1 crystallizes in the monoclinic space group C2/c, with a = 27.057(13), b = 8.108(3), c = 16.751(8) Å, β = 114.46°, V = 3345(3) ų, Z = 4. Complex 2 crystallizes in the triclinic space group P-1, with a = 9.336(3), b = 14.686(5), c = 16.911(5) Å, α = 71.36(2), β = 84.31(2), γ = 72.470(10)°, V = 2095.0(12) ų Z = 4. The structural analysis shows that each metal atom in both the mononuclear complex 1 and polynuclear complex 2 is octahedrally coordinated by four sulfur atoms and two chloro ligands or two nitrogen atoms from the thiocyanate groups, respectively. The PTU ligand can serve as either a monodentate ligand or a μ₂-bridging ligand upon coordination to a metal atom.     

Approach for Modulation of the Permselective Properties of Ni(II) Porphyrin Polymers

The electropolymerization of Ni(II) Protoporphyrin (polyNiPP) onto glassy carbon electrodes is performed in different experimental conditions, varying the supporting electrolytes, solvent, and oxidative potentials. The AFM images show different average thickness for each polymer, polyNiPP(TBAP) (0.6 μm) and polyNiPP(LiClO₄) (0.1μm). The polyNiPP(LiClO₄) describes a straight line plot of EMF versus log (C) for NO₂⁻, with the slope of 37 mV per concentration decade while the same film is not sensitive to the thiocyanate concentration. For polyNiPP(TBAP) the slope for thiocyanate progressively increase when is oxidized in aqueous solution. A sub‐Nernstian response (59 mV /decade) is obtained at 1000 mV. The Nyquist plots confirm that the method of preparation establishes the properties of films related to the movement of the ions.     

A 2D Cd(II)-MOF as a multifunctional luminescencent sensor for nitroaromatics,iron(III) and chromate ions

A Cd(II)-MOF, {[Cd(L)(4,4′-bipy)]·H₂O·DMF}_n (1) (L = nicotinic acid (2,4-dihydroxybenzylidene)-hydrazide and 4,4′-bipy = 4,4′-bipyridine), has been synthesized and characterized by microanalyses, FTIR, TGA, and single-crystal X-ray diffraction. Additionally, powder X-ray diffraction was performed to check the phase purity of the synthesized compound. Single-crystal X-ray diffraction reveals that 1 has a 2D grid network. Photoluminescent sensing of nitrobenzene, Fe(III) and CrO₄^2? ions indicates that 1 could be a candidate for developing selective luminescent sensors for these species. Theoretical calculations have been performed to gain insight into the possible mechanism of quenching effect in emission on addition of nitrobenzene in 1 which supports the mechanism operating through ground state charge transfer between 1 and nitrobenzene.     

Spectrophotometric Determination of Manganese with 4(5)-Imidazolealdoxime (Imalox)

Abstract

A method is described for the spectrophotometric determination of manganese by means of its complex with 4(5)-imidazolealdoxime, IMALOX, formed in alkaline medium. The colour system has its absorption maximum at 350 nm and obeys Beer's law over the range 0.8–8.0 μg of Mn per ml. The optimum range is 1–5 μg m^?1. The molar absorptivity is 7850 1 mol^?1 cm^?1. Relatively few ions interfere, and these can be masked with cyanide, tartrate and NTA. The experimental results have been critically analyzed and a comparison with the main spectrophotometric reagents for manganese is presented.     

Synthesis,Characterization, Antimicrobial Activities,and Structural Studies of Lanthanide (III) Complexes with 1-(4-Chlorophenyl)-3-(4-fluoro/hydroxyphenyl)prop-2-en-1-thiosemicarbazone

Twelve coordinate lanthanide (III) complexes with the general composition [Ln L₃X_n(H₂O)_n] where Ln = Pr(III), Sm(III), Eu (III), Gd (III), Tb (III), Dy (III), X = Cl^?1, NO₃ ^?2, n = 2–7, and L is 1-(4-chlorophenyl)-3-(4-fluoro/hydroxyphenyl)prop-2-en-1- thiosemicarbazone have been prepared. The lanthanide complexes (5) were derived from the reaction between 1-(4-chlorophenyl)-3-(4-fluoro/hydroxyphenyl)prop-2-en-1-thiosemicarbazone (4) with an aqueous solution of lanthanide salt. Chalcone thiosemicarbazone ligand (4) was prepared by the reaction of [1-(4-chlorophenyl)-3-(4-fluoro/hydroxyphenyl)]prop-2-enone (chalcone) (3) with thiosemicarbazide in the presence of hot ethanol. All the lanthanide-ligand 1:3 complexes have been isolated in the solid state, are stable in air, and characterized on the basis of their elemental and spectral data.

Thiosemicarbazone ligands behave as bidentate ligands by coordinating through the sulfur of the isocyanide group and nitrogen of the cyanide residue. The probable structure for all the lanthanide complexes is also proposed. The chalcone thiosemicarbazone ligands and their lanthanide complexes have been screened for their antifungal and antibacterial studies. Some of the synthesized lanthanide complexes have shown enhanced activity compared with that of the free ligand.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.     

Nickel(II)-azido/thiocyanato complexes of 1-alkyl-2-(arylazo) imidazole: single crystal X-ray structure of [Ni(Pai-Me)2(N3)2] (Pai-Me=1-methyl-2(phenylazo)imidazole)

Reaction of Ni(ClO₄)₂ · 6H₂O with 1-alkyl-2-(arylazo)imidazole (RaaiR^/) and sodium azide (NaN₃) or ammonium thiocyanate (NH₄SCN) (1 : 2 : 2 molar ratio) in methanol gives [Ni(RaaiR^/)₂(X)₂] (X=N₃ (3, 4) and SCN (5, 6). All these complexes are characterized by elemental analyses, UV–Vis and IR spectral data, thermal and magnetic moment measurements. The X-ray structure is confirmed by single crystal measurement of [Ni(Pai-Me)₂(N₃)₂] (3a). Cyclic voltammetry exhibits quasireversible response at >0.80 V corresponding to Ni(III)/Ni(II) couple along with ligand reductions at negative potential (<?0.5 V) to SCE reference. The electronic structure, spectral and redox properties are explained by DFT (Gaussian03) calculation.     

A novel spectrophotometric method for determination of cyanide using cobalt (II) phthalocyanine tetracarboxylate as a chromogen

Cobalt (II) phthalocyanine tetracarboxylate [Co (II)Pc-COOH] has been prepared and used in aqueous solutions as a novel chromogenic reagent for the spectrophotometric determination of cyanide ion. The method is based on measuring the increase in the intensity of the monomer peak in the reagent absorbance at 682 nm due to the formation of a 1 : 2 [Co (II)Pc-COOH] : [CN] complex. The complex exhibits a molar absorptivity (ε) of 7.7 × 10⁴ L mol^?1 cm^?1 and a formation constant (K_f ) of 5.4 ± 0.01 × 10⁶ at 25 ± 0.1°C. Beer's law is obeyed over the concentration range 0.15–15 µg mL^?1 (5.8 × 10^?6–5.8 × 10^?4 M) of cyanide ion, the detection limit is 20 ng mL^?1 (7.7 × 10^?7 M) the relative standard deviation is ±0.7% (n = 6) and the method accuracy is 98.6 ± 0.9%. Interference by most common ions is negligible, except that by sulphite. The proposed method is used for determining cyanide concentration in gold, silver and chromium electroplating wastewater bath solutions after a prior distillation with 1 : 1 H₂SO₄ and collection of the volatile cyanide in 1 M NaOH solution containing lead carbonate as recommended by ASTM, USEPA, ISO and APAHE separation procedures. The results agree fairly well with potentiometric data obtained using the solid state cyanide ion selective electrode.