Determination of ultra traces of lead in water samples after combined solid-phase extraction–dispersive liquid–liquid microextraction by graphite furnace atomic absorption spectrometry

A solid-phase extraction coupled with dispersive liquid–liquid microextraction (DLLME) method followed by graphite furnace atomic absorption spectrometry (GFAAS) was developed for the extraction, preconcentration, and determination of ultra trace amounts of lead in water samples. Variables affecting the performance of both steps were thoroughly investigated. Under optimized conditions, 100 mL of lead solution were first concentrated using a solid phase sorbent. The extracts were collected in 1.50 mL of THF and 18 μL of carbon tetrachloride was dissolved in the collecting solvent. Then 5.0 mL pure water was injected rapidly into the mixture of THF and carbon tetrachloride for DLLME, followed by GFAAS determination of lead. The analytical figures of merit of method developed were determined. With an enrichment factor of 1,800, a linear calibration of 3–60 ng L^?1 and a limit of detection of 1.0 ng L^?1 were obtained. The relative standard deviation for seven replicate measurements of 30 ng L^?1 of lead was 5.2 %. The relative recoveries of lead in mineral, tap, well, and river water samples at spiking level of 10 and 20 ng L^?1 are in the range 94–106 %.     

Simultaneous Determination of Gallium(III) and Indium(III) in Urine and Water Samples with Cloud Point Extraction and by Inductively Coupled Plasma Optical Emission Spectrometry

A simple, sensitive, and selective method for the determination of gallium and indium in different samples at trace levels is presented. This method was based on complexation of analyzes with 2-(5-bromo-2- pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in the presence of t-octylphenoxy-polyethoxyethanol (Triton X-100). After phase separation, the analyzed concentrations were determined by inductively coupled plasma optical emission spectrometry. Quantitative extraction of gallium and indium was performed at pH 7.0, 1.7 mmol L^?1, 5-Br-PADAP, 1.3% (w/v) Triton X-100 and at 75°C. The relative standard deviations (RSD) of this method were between 0.3% and 1.6% (C = 20 ng mL^?1, n = 9). The calibration curve is linear over the concentration range 6–200 ng mL^?1 for gallium and 2–200 ng mL^?1 for indium, respectively. The limits of detection (LOD) for gallium and indium were 0.72 and 0.28 ng mL^?1, respectively. The results showed the developed method was not susceptible to matrix effects, providing recoveries between 98% and 102%. The accuracy of the developed method was evaluated by the analysis of spiked certified reference materials. The developed method was successfully applied to gallium and indium determination in urine and lake water with satisfactory results.     

Multiwalled Carbon Nanotubes as SPE Adsorbents for Simultaneous Determination of Seven Sulfonylurea Herbicides in Environmental Water by LC–MS–MS

An effective and rapid method was developed for simultaneous determination of seven sulfonylurea herbicides in environmental water using multiwalled carbon nanotubes as solid-phase extraction sorbent coupled with liquid chromatography–tandem mass spectrometry. Important parameters influencing the extraction efficiency such as pH of the sample solution, flow rate of sample loading, the eluent and its volume were optimized. Under optimum conditions, good linearity was obtained for all herbicides (r ² > 0.99) over the range of 0.05–5,000 ng L^?1, and precisions (RSD) for nine replicate measurements of a standard mixture of 200 ng L^?1 were 1.9–7.4%. The limits of detection and quantification were 0.01–0.20 and 0.05–1.00 ng L^?1, respectively. The proposed method was successfully applied to the analysis of tap water, spring water, ground water and well water, and mean recoveries for seven analytes at three spiked concentration levels were from 81.5 to 110.5% with RSDs between 0.3 and 7.0%. The results showed that the established method has wide application to analyze sulfonylurea herbicides at trace level in water.     

Development of Immunoaffinity Sample-Purification for GC–MS Analysis of Ractopamine in Swine Tissue

A method combining immunoaffinity chromatography with gas chromatography–mass spectrometry (GC–MS) has been established for determination of ractopamine residues in swine liver and urine. After clean-up on an immunoaffinity chromatography column, GC–MS analysis revealed recovery from blank swine liver and urine fortified at 2.5–20 ng g^?1 (ng mL^?1 for urine), respectively, was 68.2–78.6 and 76.2–83.1%. The limits of detection and quantification were 0.5 ng g^?1 (or ng mL^?1) and 2.0 ng g^?1 (or ng mL^?1), respectively. The procedure was used for analysis of ractopamine residues in samples of swine liver and urine in which the levels were unknown. The amounts detected were 9–216 ng g^?1 (ng mL^?1).     

Trace analysis of benzophenone-derived compounds in surface waters and sediments using solid-phase extraction and microwave-assisted extraction followed by gas chromatography–mass spectrometry

This study describes a procedure for determining eight benzophenone-derived compounds in surface waters and sediments. These include the pharmaceutical ketoprofen, its phototransformation products 3-ethylbenzophenone and 3-acetylbenzophenone, and five benzophenone-type ultraviolet (UV) filters. The proposed analytical method involves the pre-concentration of water samples by solid-phase extraction (SPE) and microwave-assisted extraction (MAE) of sediment samples followed by derivatization and analysis by gas chromatography–mass spectrometry. Different parameters were investigated to achieve optimal method performance. Recoveries of 91 to 96 % from water samples were obtained using HLB Oasis SPE cartridges, whereas MAE of sediments (30 min at 150 °C) gave recoveries of 80 to 99 %. Limits of detection were between 0.1 and 1.9 ng L^?1 for water samples and from 0.1 to 1.4 ng g^?1 for sediment samples. The developed method was applied to environmental samples and revealed the presence of UV filters in the majority of the surface waters with up to 690 ng L^?1 of 2-hydroxy-4-methoxybenzophenone. By contrast, ketoprofen (≤2,900 ng L^?1) and its degradation products (≤320 ng L^?1) were found in only two rivers, both receiving wastewater treatment plant effluents. Sediment analysis revealed benzophenone to be present in concentrations up to 650 ng g^?1, whereas concentrations of other compounds were considerably lower (≤32 ng L^?1). For the first time, quantifiable amounts of two ketoprofen transformation products in the aqueous environment are reported.     

Dispersive liquid–liquid microextraction combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples

Dispersive liquid–liquid microextraction (DLLME) was combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples. The metal elements were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors for Cd, Pb and Bi are 460, 900 and 645 in 5 mL of a spiked water sample, respectively. The calibration graphs for the three metals are linear in the range of concentrations from <10 ng L^?1 to 1,000 ng L^?1. The detection limits are 0.5 ng L^?1, 1.6 ng L^?1 and 4.7 ng L^?1, respectively. The relative standard deviations for ten replicate measurements of 50 ng L^?1 cadmium, lead and bismuth are 2.6%, 6.7%, and 4.9%, respectively, and the relative recoveries in various water samples at a spiking level of 50 ng L^?1 range from 83.6% to 107.0%.     

Determination of Pyrethroid Pesticides in Environmental Waters Based on Magnetic Titanium Dioxide Nanoparticles Extraction Followed by HPLC Analysis

A simple and fast method based on magnetic separation for extraction of pyrethroid pesticides including beta-cyfluthrin, cyhalothrin and cyphenothrin from environmental water samples has been established. Magnetic titanium dioxide was used as sorbent, which was synthesized by coating TiO₂ on Fe₃O₄ in liquid-state co-precipitation method. The sorbent has been characterized by scanning electron microscopy and Fourier-transform infrared spectrometry, and the magnetic properties were investigated with physical property measurement system. Various parameters affecting the extraction efficiency were evaluated to achieve optimal condition and decrease ambiguous interactions. The analytes desorbed from the sorbent were detected by high performance liquid chromatography. Under the optimal condition, the linearity of the method is in the range of 25–2,500 ng L^?1. The detection limits and quantification limits of pyrethroid pesticides are in the range of 2.8–6.1 ng L^?1 and 9.3–20.3 ng L^?1, respectively. The relative standard deviations of intra- and inter-day tests ranging from 2.5 to 7.2 % and from 3.6 to 9.1 % were obtained. In all three spiked levels (25, 250 and 2,500 ng L^?1), the recoveries of pyrethroid pesticides were in the range of 84.5–94.1 %. The proposed method was successfully applied to determine pyrethroids in three water samples. Cyphenothrin was found in one river water near farmlands, and its concentration was 52 ng L^?1.     

Activated Carbon Modified with Sodium Dodecyl Sulfonate as a Solid Phase Sorbent for the Separation and Preconcentration of Trace Cadmium in Water Samples with Detection by Electrothermal Atomic Absorption Spectrometry

A novel absorbent was prepared by sodium dodecyl sulfonate (SDS)-modified activated carbon (SDS-AC) and was employed as the microcolumn packing material for separation/preconcentration of trace Cd(II). The method based on Cd(II) was quantitatively retained by SDS-AC sorbent, which entailed cation exchange nature and negative charged surface, facilitating favorable retention of positively charged ions. The retained Cd(II) was effectively recovered with elution by 1 mol · L^?1 HNO₃, and the eluent was quantified by electrothermal atomic absorption spectrometry (ET-AAS). Under the optimized conditions, the limit of detection (LOD) for Cd(II) was 3 ng · L^?1 with the consumption of 20.0 mL sample solution. The relative standard deviation (RSD) for ten replicate measurements of 50 ng · L^?1 Cd(II) was 2.9%. The developed technique was demonstrated for the determination of trace Cd(II) in water samples and the recoveries for spiked samples were found to be in the range of 94.9–107.2%. For validation, two certified reference materials of water samples (GBW08607 and GBW08608) were analyzed, and the results obtained were in good agreement with the certified values.     

Occurrence of cytostatic compounds in hospital effluents and wastewaters,determined by liquid chromatography coupled to high-resolution mass spectrometry

The occurrence of 26 commonly used cytostatic compounds in wastewaters was evaluated using an automated solid-phase extraction (SPE) method with liquid chromatography–high-resolution mass spectrometry (LC–HRMS). Detection was optimized using Oasis HLB SPE cartridges at pH 2. Two hospital effluents and their two receiving wastewater treatment plants were sampled over five days. In hospital effluents, eight cytostatics were detected at levels up to 86.2 μg L^?1 for ifosfamide, 4.72 μg L^?1 for cyclophosphamide, and 0.73 μg L^?1 for irinotecan, the three most relevant compounds identified. Cyclophosphamide and megestrol acetate were found in wastewaters at concentrations up to 0.22 μg L^?1 for the latter. The predicted environmental concentrations (PEC) in sewage effluents of ifosfamide (2.4–4.3 ng L^?1), capecitabine (11.5–14.2 ng L^?1), and irinotecan (0.4–0.6 ng L^?1), calculated from consumption data in each hospital, published excretion values for the target compounds, and wastewater elimination rates, were in agreement with experimental values.     

Feasibility of hydrofluoric acid etched sand particles for enrichment and determination of polychlorinated biphenyls at trace levels in environmental water samples

This study aims to investigate the feasibility of etched sand particles being used as solid-phase extraction adsorbents to enrich polychlorinated biphenyls (PCBs), which are typical persistent organic pollutants in the environment, at trace levels. Gas chromatography–tandem mass spectrometry was selected to detect the compounds. Etched sand particles exhibited excellent merits on the enrichment of PCBs. Related important factors affecting extraction efficiencies were investigated and optimized in detail. Under optimized conditions, low limits of detection (0.42 to 3.69 ng L^?1), wide linear range (10 to 1,000 ng L^?1), and high repeatability (1.9 to 8.2 %) were achieved. The developed method was validated with several real water samples, and satisfactory results were obtained. All of these findings indicate that etched sand particles would be useful for the enrichment and determination of organic pollutants at trace levels in water samples.     

Stripping voltammetry method for determination of manganese as complex with oxine at the carbon paste electrode with and without modification with montmorillonite clay

Oxine (8-hydroxyquinoline) was used as an efficient and selective ligand for stripping voltammetry trace determination of Mn(II). A validated square-wave adsorptive cathodic stripping voltammetry method has been developed for determination of Mn(II) selectively as oxine complex using both the bare carbon paste electrode (CPE) and the modified CPE with 7 % (w/w) montmorillonite-Na clay. Modification of carbon paste with montmorillonite clay was found to greatly enhance its adsorption capacity. Limits of detection of 45 ng l^?1 (8.19?×?10^?10 mol L^?1) and 1.8 ng l^?1 (3.28?×?10^?11 mol L^?1) Mn(II) were achieved using the bare and modified CP electrodes, respectively. The achieved limits of detection of Mn(II) as oxine complex using the modified CPE are much sensitive than the detection limits obtained by most of the reported electrochemical methods. The developed stripping voltammetry method using both electrodes was successfully applied for trace determination of Mn(II) in various water samples without interferences from various organic and inorganic species.     

Removal, preconcentration and spectrophotometric determination of U(VI) from water samples using modified maghemite nanoparticles

Arsenazo III modified maghemite nanoparticles (A-MMNPs) was used for removing and preconcentration of U(VI) from aqueous samples. The effects of contact time, amount of adsorbent, pH and competitive ions was investigated. The experimental results were fitted to the Langmuir adsorption model in the studied concentration range of uranium (1.0 × 10^?4–1.0 × 10^?2 mol L^?1). According to the results obtained by Langmuir equation, the maximum adsorption capacity for the adsorption of U(VI) on A-MMNPs was 285 mg g^?1 at pH 7. The adsorbed uranium on the A-MMNPs was then desorbed by 0.5 mol L^?1 NaOH solution and determined spectrophotometrically. A preconcentration factor of 400 was achieved in this method. The calibration graph was linear in the range 0.04–2.4 ng mL^?1 (1.0 × 10^?10–1.0 × 10^?8 mol L^?1) of U(VI) with a correlation coefficient of 0.997. The detection limit of the method for determination of U(VI) was 0.01 ng mL^?1 and the relative standard deviation (R.S.D.) for the determination of 1.43 and 2.38 ng mL^?1 of U(VI) was 3.62% and 1.17% (n = 5), respectively. The method was applied to the determination of U(VI) in water samples.     

Application of DLLME to Isolation and Concentration of Non-Steroidal Anti-Inflammatory Drugs in Environmental Water Samples

Dispersive liquid–liquid microextraction (DLLME) coupled with liquid chromatography-tandem mass spectrometry detection was applied for determination of selected anti-inflammatory pharmaceuticals: ibuprofen, ketoprofen, naproxen and diclofenac. Development of DLLME procedure included optimisation of several important parameters such as kind and volume of extracting and dispersive solvents as well as sample pH. Under optimised conditions a two-step extraction with sonication was used. Chloroform was applied as the extracting and acetone as dispersing solvent. Calibration curves ranges were 1–500 μg L^?1 for naproxen and ibuprofen and 0.25–500 μg L^?1 for ketoprofen and diclofenac with correlation coefficients at least 0.997. Limits of quantitation were from 0.5 to 10 ng L^?1. The developed analytical method was employed for determination of ibubrofen, ketoprofen, naproxen and diclofenac in river and tap water samples. The results showed that DLLME is a simple, rapid and sensitive analytical technique for the pre-concentration of trace amounts of pharmaceuticals in environmental water samples.     

Determination of Low-Molecular-Mass Aldehydes in Water Samples by Liquid Chromatography and Chemiluminescence Detection Using Continuous in situ Derivatization/Preconcentration with Dansylhydrazine

Abstract

A simple, expeditious, and sensitive method has been developed for the determination of low-molecular-mass aldehydes in water samples by liquid chromatography and peroxyoxalate–chemiluminescence detection. The method is based on continuous solid-phase extraction with in situ derivatization/preconcentration of the aldehydes using dansylhydrazine, which was first adsorbed on an RP–C₁₈ mini-column. For 10 mL of aqueous sample, the limits of detection (LOD) for C₁ to C₄ aldehydes were 20–30 ng L^?1, except for formaldehyde, which had an LOD of 400 ng L^?1. Application was illustrated by the determination of these aldehydes in water samples; the interday precision was always less than ca. 7%, and relative recoveries were more than 96%.     

A Modified Nanoporous Silica Aerogel as a New Sorbent for Needle Trap Extraction of Chlorobenzenes from Water Samples

In this work, a modified nanoporous silica aerogel was used as a new sorbent for headspace needle trap extraction of chlorobenzenes from aqueous samples. The needle trap extraction is derived from solid-phase microextraction and the sorbent is inside the needle. The thermal stability and functional groups of the sorbent were studied by TG/DTA and FT-IR, respectively. The modified silica aerogels, characterized by field emission scanning electron microscopy, showed a three-dimensional network containing a homogeneous pore structure with pore sizes of a few tens of nm and a sponge-like microstructure. The developed method was applied to the trace level extraction of some chlorobenzene compounds from aqueous samples. The influential parameters on the extraction efficiency, including the extraction temperature, ionic strength and extraction time were investigated and optimized. Under optimized conditions, the detection and quantification limits were in the range of 0.4–0.8 and 1–3 ng L^?1, respectively. The relative standard deviation values for water spiked with chlorobenzenes at 100 ng L^?1 under optimum conditions were 3–7%. The dynamic linear range of the method in the range of 3–3000 ng L^?1 was investigated. Finally, the current method for the analysis of real water samples containing spiked chlorobenzenes was applied and the relative recovery values were found to be in the range of 96–101%.     

Sol-Gel-based SPME and GC–MS for Trace Determination of Geosmin in Water and Apple Juice Samples

A headspace solid-phase microextraction (HS-SPME) method was developed for the trace determination of geosmin in water and apple juice samples. A poly(dimethylsiloxane) (PDMS) fiber was synthesized as coated fiber using sol-gel methodology. After performing the extraction in the headspace, the fiber was introduced directly into the injection port of a gas chromatography-mass spectrometry (GC–MS) using electron impact (EI) ionization mode. One-at-the-time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature and time, ionic strength, headspace volume, and desorption temperature and time. The analytical data exhibited an RSD of 2–15%, a linear calibration range of 1–1,000 ng L^?1, and a detection limit of 0.30 ng L^?1 using selected ion monitoring (SIM) mode. The proposed method was successfully applied to the extraction and determination of geosmin in the spiked real water and apple juice samples and a relative recovery of 95–102% were achieved. The developed method offers the advantage of being simple to use, with shorter analysis times, lower cost of equipment, very little matrix effect, and high relative recovery in comparison to conventional methods of analysis.     

Preparation of an ionic liquid-mediated carbon nanotube-poly(dimethylsiloxane) fiber by sol–gel technique for determination of polycyclic aromatic hydrocarbons in urine samples using head-space solid-phase microextraction coupled with gas chromatography

A novel ‘ionic liquid-mediated multi-walled carbon nanotube (MWCNT)-poly(dimethylsiloxane) (PDMS)’ hybrid coating was prepared by the covalent functionalization of MWCNTs with hydroxyl-terminated PDMS using the sol–gel technique. The prepared fiber was successfully used for the separation and determination of trace amounts of polycyclic aromatic hydrocarbon compounds (PAHs) in four urine samples using head-space solid-phase microextraction coupled to gas chromatography-flame ionization detection. The proposed fiber has high thermal stability and long durability and it can be used more than 210 times without any significant change in its sorption properties. The effects of important parameters such as the exposure time, sampling temperature, sample ionic strength and stirring rate on the extraction efficiency have been studied and optimized. Under the optimal conditions, the method detection limits (S/N = 3) were in the range of 0.0005–0.004 ng mL^?1 and the limits of quantification (S/N = 10) between 0.002 and 0.01 ng mL^?1. The relative standard deviations for one fiber (repeatability, n = 5) were 4.9–7.5 % and for the fibers obtained from different batches (reproducibility, n = 3), 6.1–8.9 %. The developed method was successfully applied to determine trace levels of PAHs in real urine samples. The obtained relative recoveries for the spiked samples with 0.05 ng mL^?1 of each of the PAH compounds were 89.3–107.2 %.     

Determination of methyl mercury in water samples with electromagnetic induction thermal desorption/pyrolysis coupled to atomic fluorescence spectrometry

A novel non-chromatographic method for the pre-concentration and determination of trace methyl mercury in water samples has been proposed. This method included two main steps: (1) The methyl mercury in sample solution was adsorbed on PDMS of the Fe/SiO₂/PDMS bed enrichment column; (2) the analyte was thermally desorbed from the enrichment column and pyrolysed to Hg⁰ in an iron particle bed pyrolysis column by using electromagnetic induction heating technique, and then detected by an on-line coupled atomic fluorescence detector. Several factors affecting the enrichment column preparation and concentration procedure have been investigated and optimised. Under optimal condition, the detection limit (3σ) was 0.2 ng L^–1, along with relative standard deviations of 2.4% (10 ng L^–1, N = 11) for the repeatability study. The enrichment factor obtained was 108. The two standard reference materials (GBW08675, GBW10029) were analysed to validate the present method. This method was successfully applied to the determination of ng L^–1 methyl mercury in water samples.     

QuEChERS and solid phase extraction methods for the determination of energy crop pesticides in soil,plant and runoff water matrices

QuEChERS and solid phase extraction (SPE) methods were applied for determining four herbicides (metazachlor, oxyfluorfen, quizalofop-p-ethyl, quinmerac) and one insecticide (α(±)-cypermethrin) in runoff water, soil, sunflower and oilseed rape plant matrices. Determination was performed using gas chromatography mass spectrometry (GC-MS), whereas high-pressure liquid chromatography mass spectrometry (HPLC-MS) was used for quinmerac. In all substrates linearity was evaluated using matrix-matched calibration samples at five concentration levels (50–1000 ng L^?1 for water, 5–500 μg kg^?1 for soil and 2.5–500 μg kg^?1 for sunflower or oilseed rape plant). Correlation coefficient was higher than 0.992 for all pesticides in all substrates. Acceptable mean recovery values were obtained for all pesticides in water (65.4–108.8%), soil (70.0–110.0%) and plant (66.1–118.6%), with intra- and inter-day RSD% below 20%. LODs were in the range of 0.250–26.6 ng L^?1 for water, 0.10–1.8 μg kg^?1 for soil and 0.15–2.0 μg kg^?1 for plants. The methods can be efficiently applied for field dissipation studies of the pesticides in energy crop cultivations.     

Determination of silver(I) ion in water samples by graphite furnace atomic absorption spectrometry after preconcentration with dispersive liquid-liquid microextraction

A method was developed for the determination of silver ion (Ag) by combining dispersive liquid-liquid microextraction preconcentration with graphite furnace atomic absorption spectrometry. Diethyldithiocarbamate was used as a chelating agent, and carbon tetrachloride and methanol as extraction and dispersive solvent. Factors influencing the extraction efficiency of Ag and its subsequent determination were studied and optimized. The detection limit is 12 ng L^?1 (3 s) with an enrichment factor of 132, and the relative standard deviation is 3.5% (n?=?7, at 1.0 ng mL^?1). The method was successfully applied to the determination of trace amounts of Ag in water samples.