Simultaneous Determination of Gallium(III) and Indium(III) in Urine and Water Samples with Cloud Point Extraction and by Inductively Coupled Plasma Optical Emission Spectrometry

A simple, sensitive, and selective method for the determination of gallium and indium in different samples at trace levels is presented. This method was based on complexation of analyzes with 2-(5-bromo-2- pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in the presence of t-octylphenoxy-polyethoxyethanol (Triton X-100). After phase separation, the analyzed concentrations were determined by inductively coupled plasma optical emission spectrometry. Quantitative extraction of gallium and indium was performed at pH 7.0, 1.7 mmol L^?1, 5-Br-PADAP, 1.3% (w/v) Triton X-100 and at 75°C. The relative standard deviations (RSD) of this method were between 0.3% and 1.6% (C = 20 ng mL^?1, n = 9). The calibration curve is linear over the concentration range 6–200 ng mL^?1 for gallium and 2–200 ng mL^?1 for indium, respectively. The limits of detection (LOD) for gallium and indium were 0.72 and 0.28 ng mL^?1, respectively. The results showed the developed method was not susceptible to matrix effects, providing recoveries between 98% and 102%. The accuracy of the developed method was evaluated by the analysis of spiked certified reference materials. The developed method was successfully applied to gallium and indium determination in urine and lake water with satisfactory results.     

浊点萃取-流动注射电感耦合等离子体原子发射光谱法同时测定水中镉钴铜镍锌

本文提出了浊点萃取-流动注射电感耦合等离子体原子发射光谱（FI—ICP—AES）法同时测定水中镉、钴、铜、镍、锌的新方法。利用5-Br—PADAP将待测金属离子转化为水不溶性的螯合物，并萃取到表面活性剂Triton X-114的浓缩相，以乙醇-硝酸溶液稀释含富集离子的浓缩相，并以FI—ICP-AES法测定。考察了流动注射进样体积、积分时间、萃取体系介质酸度、螯合剂和表面活性剂用量等实验条件的影响。在折衷条件下，镉、钴、铜、镍和锌的浓缩倍率可达18、10、16、10和8，检出限分别为0．7μg／L、1．6μg／L、1．3μg／L、5．7μg／L、3．2μg／L。方法成功应用于自来水、河水和海水中痕量镉、钴、铜、镍和锌的分析。在0．02mg／L和0．10mg／L二个水平进行加入回收试验，回收率在80％与118％之间。     

碘化钾-甲基异丁基甲酮萃取电感耦合等离子体发射光谱法测定磷酸一铵、磷酸二铵中铊含量

通过对观测方式、测定波长、共存元素干扰等因素进行分析和条件优化,建立了测定磷酸一铵、磷酸二铵中铊含量的碘化钾-甲基异丁基甲酮（KI-MIBK）萃取电感耦合等离子体发射光谱法。实验表明,直接采用电感耦合等离子体发射光谱法进行测定时,磷酸一铵、磷酸二铵中的锰元素对分析结果有正干扰。通过萃取分离,干扰被排除,测定结果准确、可靠。在0～1.0 mg/L范围内,铊的质量浓度与光谱强度呈良好的线性关系,相关系数达1.0000。该方法检出限为0.0072 mg/kg,相对标准偏差为4.28%（n = 10）,加标回收率在97.00%～100.5%之间。     

电感耦合等离子体原子发射光谱法测定石油化工废催化剂中铂的含量

本文研究了石油化工废催化剂中铂含量的电感耦合等离子体原子发射光谱测定方法。国标GB/T 23524-2009中采用氯气来氧化络合铂,然后通过电感耦合等离子发射光谱法来测定溶液中的铂含量。由于氯气有毒,腐蚀性强,安全性低,本文提出了用盐酸与氯酸钠氧化络合铂替代氯气氧化络合铂的方法。通过对电感耦合等离子体原子发射光谱仪参数、测定谱线、盐酸浓度及氯酸钠用量等条件进行了研究,得到实验的优化条件。结果表明,以低浓度硫酸为介质,用标准曲线法进行样品分析,方法的检出限为0.0001 μg/mL,样品的加标回收率为 97.7% ~100.9%,铂含量测定值与GB/T 23524-2009测定值几乎相同。通过试验结果可知,该方法准确性好、精密度高,准确快速,操作简单。     

电感耦合等离子体光谱法测定废钒触媒中钒的含量

本文建立了用盐酸、硝酸、氢氟酸和高氯酸的混合酸溶解样品,采用电感耦合等离子体发射光谱法(ICP-OES)测定废钒触媒中钒含量的分析方法。该方法确定了最佳溶样方法和仪器的最佳条件。在选定的操作条件下,钒的检出限0.026μg/mL。相对标准偏差(n=11),RSD<1%,加标回收率在98.85%-101.30%之间。用该法测定废钒触媒中钒的含量,流程短,易操作,结果令人满意。     

浊点萃取预富集火焰原子吸收光谱法测定水样中痕量钴

本文提出了浊点萃取预富集火焰原子吸收光谱法测定痕量钴的新方法。详细研究了溶液pH值、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。在优化的实验条件下,本法对钴的富集倍数为20倍,检出限为3．28ng／mL,相对标准偏差(RSD)为4．1％(n=10)。所建立的方法用于自来水、湖水中痕量钴的测定,分析结果满意。     

电感耦合等离子体发射光谱(ICP-OES)法测定石灰石中5种氧化物含量

建立了电感耦合等离子体发射光谱(ICP-OES)法测定石灰石样品中5种氧化物氧化镁(MgO)、三氧化二铁(Fe_2O_3)、二氧化硅(SiO_2)、氧化锰(MnO)、三氧化二铝(Al2O3)含量的方法。先将样品与无水碳酸钠和四硼酸钠高温熔融后,再用盐酸进行消解可以很好地溶解石灰石样品。选择Mg285.21nm、Fe 238.20nm、Si 251.61nm、Mn 257.61nm、Al 396.15nm为分析谱线,采用空白校正的方法校正基体的影响。在选定的实验条件下,各元素标准曲线的线性相关系数均不小于0.999,测定结果的相对标准偏差(RSD,n=6)在1.8%～2.4%,各测定元素的加标回收率也在94%～105%。按照实验方法将各元素测定结果与5种国家标准测定方法得出的结果进行比对,准确度、精密度、回收率均在理想范围内。结果表明,所建立的方法可以满足石灰石中5种元素联测的要求,并且更加快速、准确。     

电感耦合等离子体光谱/质谱联机同时测定多金属结核中常量、微量、痕量元素

采用电感耦合等离子体质谱(ICP-MS)与等离子体光谱(ICP-OES)联机同时测定多金属结核样品中常量、微量、痕量元素。样品经高压密封溶样弹消解后,一次气动雾化进样,ICP-OES测定常量和微量元素,ICP-MS测定微量和痕量元素。详细探讨了不同浓度范围元素的测定方式、元素分析信号的采集模式、多原子离子干扰的校正因子。采用ICP-MS与ICP-OES二种方式同时测定Co、Cu、Ni、Zn、V、Ba、Sr,分析结果表明具有较好的一致性。所建立的ICP-MS与ICP-OES联机检测技术用于多金属结核标准样品的分析(Nod-A-1,GSPN-1,GSPN-2,GSPN-3),分析结果与推荐值符合,相对标准偏差小于10％。     

Preconcentration and Determination of Tin in Water Samples by Using Cloud Point Extraction and Graphite Furnace Atomic Absorption Spectrometry

A method based on cloud point extraction and graphite furnace atomic absorption spectrometry (GFAAS) was developed for the analysis of trace tin in water samples. After cloud point extraction, the tin in the water samples was preconcentrated and successfully separated from most interferents. During the procedure, 8-hydroxyquinoline (8-HQ) was used as chelating reagent, and Triton X-114 was added as surfactant. The parameters affecting the sensitivity and the extraction efficiency, such as solution pH, concentration of 8-HQ and Triton X-114, equilibration temperature and centrifuge time, were evaluated and optimized. Under the optimum conditions, a preconcentration factor of 96.2 was obtained for a 20 mL water sample. The detection limit (LOD) was as low as 0.012 ng mL⁻¹, and the analytical curve was linear in the range of 0.05–2.0 ng mL⁻¹ with satisfactory precision (RSD <4.1%). The proposed method was successfully applied to the determination of trace tin in water samples with recoveries in the range of 85.0–112.0%.     

Selective Determination of Copper in Water Samples by Atomic Absorption Spectrometry after Cloud Point Extraction

A preconcentration methodology utilizing the cloud point phenomenon is described for the determination of copper by flame atomic absorption spectrometry. The reagent Sulfathiazolylazo resorsin was used as a complexing agent. The preconcentration factor of 25-fold was obtained. The calibration curve is linear in the range of 4–400 µ g L^?1 with a limit of detection of 0.64 µ g L^?1. The relative standard deviation (n = 5, 12 µ g L^?1) was 3.5%. The cloud point is formed in the presence of phenol at room temperature. The method was successfully applied to the determination of copper in water samples and a standard reference material.     

浊点萃取-火焰原子吸收光谱法测定矿渣中痕量金

研究了以双硫腙为络合剂,以非离子型表面活性剂Triton X-100为萃取剂的浊点萃取-火焰原子吸收光谱法(CPE-FAAS)测定痕量金(Ⅲ)的新方法。详细考察了溶液的pH值、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法的线性范围为0.05~0.8μg/mL,检出限为7.9 ng/mL,相对标准偏差为4.12%(n=11),回收率在98.0%~102.0%之间,用于矿渣中金的测定,结果满意。     

Investigation of Simultaneous Generation of Arsenic,Bismuth and Antimony Hydrides Using Inductively Coupled Plasma Optical Emission Spectrometry

Hydride generation from solution containing As(III), Bi(III), and Sb(III) by means of different borane reductants and acids using inductively coupled plasma optical emission spectrometry as a detection system was investigated. The As, Bi, Sb, B, C, H, and N lines as well as the OH and CN molecules were recorded. Their intensities in relation to hydride formation conditions were measured. Effects of the HCl, CH₃COOH, and C₆H₈O₇ acids as well as the NaBH₄, H₃B-NH(CH₃)₂, and H₃B-NH₂C(CH₃)₃ reductants on efficiency of the As, Sb, and Bi hydride generation were investigated and discussed. Influence of hydride generation conditions on plasma was studied.     

Fluorescence Quenching Method for Determination of Trace Tungsten in Soil after Cloud Point Extraction

A new procedure for trace tungsten W(VI) in soil by fluorescence quenching method coupled with cloud point extraction (CPE) as the separation-preconcentration method was described. The Triton X-100 CPE behavior of W(VI)-salicylfluorone (SAF)was investigated. Under the optimized conditions, the fluorescence quenched intensity (ΔF) was linearly with W(VI). The range of linear was 0.8 ～ 20.0 μg · L^?1, the detection limit (DL) was 0.14 ng · mL^?1 (3σ), the relative standard deviation 3.3% (c = 10.0 μg · L^?1, n = 5) and the recovery was 101.0–102.2%. The proposed method applied to the analysis of W(VI) in certified reference materials and real samples.     

A Pre-Concentration Procedure Using Cloud Point Extraction for the Determination of Manganese in Saline Effluents of a Petroleum Refinery by Flame Atomic Absorption Spectrometry

This paper describes the development of a cloud point extraction procedure for the determination of manganese in saline effluents by flame atomic absorption spectrometry (FAAS). The optimization step was performed using the Doehlert matrix involving the following variables: buffer concentration, pH and centrifugation time. The validation process was assessed as: parameters of the analytical curve, precision, effect of other ions in the proposed procedure, robustness test and accuracy. The proposed procedure allows the determination of manganese with a detection limit (3δ/S) of 0.60 μg L⁻¹, and a precision expressed as relative standard deviation (RSD) of 2.2 (n = 8) and 1.5% (n = 8) for a manganese concentration of 1 and 5 μg L⁻¹, respectively. The pre-concentration factor obtained was 84. The recovery achieved for the determination of manganese in the presence of several other metal ions demonstrated that this procedure could be satisfactorily applied to the analysis of environmental samples. The accuracy was confirmed by the analysis of CRM trace elements in water (NIST 1643d). This procedure was applied to the determination of manganese in saline effluents of a petroleum refinery. For three analyzed samples the manganese content varied between 44.9 and 67.9 μg L⁻¹.     

浊点萃取-石墨炉原子吸收光谱法测定环境样品中的镉

建立了浊点萃取分离富集石墨炉原子吸收光谱法测定环境样品中痕量镉的方法.浊点萃取选择8-羟基喹啉为螯合剂,Triton X-100为表面活性剂.在pH 8～9、0.01%8-羟基喹啉和0.2%-Triton X-100、80 ℃水浴20 min的优化条件下,所建立方法的检出限为2.5 ng/L; 加标回收率为94.6%～106.2%; 对样品溶液进行富集的富集因子为17.利用该方法分别测定了2个实际水样和2个国家标准参考物质中的总镉含量,结果令人满意.     

Determination of Titanium in Nano-Titanium(IV) Oxide Composite Food Packaging by Microwave Digestion and Inductively Coupled Plasma Atomic Emission Spectrometry and Inductively Coupled Plasma Mass Spectrometry

Titanium was determined in nano-titanium(IV) oxide food packaging by microwave digestion with inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). Microwave digestion was optimized using different acid combinations. Both spectrometry techniques showed good reproducibility, repeatability, and recovery. For ICP-AES, the limit of detection was 5.0 mg kg^?1, the linear dynamic range was 100–5000 µ g L^?1, the average recoveries for blank samples spiked with titanium were between 94.7% and 100.1%, and the relative standard deviations were from 2.1% to 7.1%. By ICP-MS, the limit of detection was 0.3 mg kg^?1, the linear dynamic range was 0.5–200 µ g L^?1, the recoveries were 88.4%–96.3%, and the relative standard deviations were 6.3%–7.4%. These results indicated that methods were effective for the determination of titanium in food packaging.     

浊点萃取-异辛烷反萃取-气相色谱测定茶叶中拟除虫菊酯农药残留

建立了浊点萃取-异辛烷反萃取-气相色谱(ECD)检测茶叶中联苯菊酯(Bifenthrin)、甲氰菊酯(Fenpropathrin)、功夫菊酯(Cyhalothrin)、氯菊酯(Permethrin)、氰戊菊酯(Fenvalerate)、溴氰菊酯(Deltamethrin)6种拟除虫菊酯农药残留的方法.对含1.2%(m/V)聚乙二醇6000(PEG6000)表面活性剂和40%(m/V)(NH4)2SO4的6种拟除虫菊酯溶液进行加热萃取,所获得的富集相用异辛烷超声反萃取,并经离心对上层异辛烷溶液进行进一步净化处理,即可获得富集倍数达75倍的6种农药.本方法的检出限(LOD)为:联苯菊酯、甲氰菊酯和功夫菊酯0.4 μg/kg;氰戊菊酯2.1 μg/kg;氯菊酯和溴氰菊酯3.0 μg/kg;用本方法测定了新鲜茶叶中6种拟除虫菊酯农药,含量分别为4.17, 4.15, 4.09, 4.01, 3.93和3.51 μg/kg.在上述茶叶样品中添加20 μg/kg 的6种农药后测定,添加回收率为72.3%～85.6%; 相对标准偏差为2.2%～5.6%.     

FI溶剂萃取与ICP-AES联机的研究水样中微量铜的测定

本文建立了用FI-溶剂萃取-ICP-AES测定水样中微量铜的分析方法。选择了ICP-AES、超声雾化发生器及FIA的最佳工作条件。研究了溶液pH对用打萨腙-四氯化碳体系萃取铜的影响;有机相流速与水相流速之比例;萃取盘管长度等因素对萃取过程及等离子体放电的影响。分析了自来水样品及美国标准局标准水样中铜含量。统计了分析方法的精密度、检出限与实验条件下的富集倍数。     

Determination of Vitamins A and E Exploiting Cloud Point Extraction and Micellar Liquid Chromatography

Cloud point extraction and micellar chromatographic methods were developed for determination of vitamins A and E. The stationary phase was C18 and the mobile phase was 3.00% (w/v) SDS, 15.0% (v/v) butyl alcohol and 0.02 mol L^?1 phosphate buffer solution at pH 7.0. The retention times for vitamins A and E were 9.6 and 13.0, respectively. The extraction solution was 100 mmol L^?1 Triton X-100, 650 mg NaCl and 1.0% ascorbic acid at 70°C for 30 min. The method is precise (r.s.d. < 7%), the linear range was from 5.0 up to 360.0 mg L^?1 for both vitamins. Recovery test showed recuperation between 90.2 and 99.2%, and LOD and LOQ of 0.234 and 0.108 mg L^?1, 0.780 and 0.360 mg L^?1 to vitamins A and E were found.     

Determination of Ultratrace Amounts of Copper（ Ⅱ ） in Water Samples by Electrothermal Atomic Absorption Spectrometry After Cloud Point Extraction

IntroductionIn environment, copper is usually found in traceor ultratrace levels, and its detection requires sensitiveinstrumental measuring techniques such as electrother-mal atomic absorption spectrometry(ETAAS) and ICP-AES or ICP-MS. Frequently, a prec…