Indirect Flow-Injection Analysis of Ascorbic Acid by Photochemical Reduction of Methylene Blue

Abstract

Ascorbic acid was determined indirectly by spectrophotometry at 666 nm based on the photochemical reduction of methylene blue using flow-injection analysis. The carrier stream was 12.7 μgml^?1 methylene blue in phthalate-HCl buffer solution at pH 3.2. The reactor was irradiated with a 500-Watt halogen lamp to facilitate the development of the photochemical reaction. The system allows determination of ascorbic acid in the range 0.18–6.12 μgml^?1 with relative standard deviations of 2.09 and 0.31% for 1.97 and 4.92 μgml^?1 samples, respectively, and a sampling frequency of 50–55 h^?1. The proposed method was applied successfully to the determination of ascorbic acid in vitamin C tablets.     

Investigation of Protein Binding With All Solid‐State Ion‐Selective Electrodes

A potentiometric sensor for studying charge based adsorption of proteins was created using a single‐piece polyaniline‐PVC ion‐selective electrode (ISE). Three different ISEs, two for Na⁺ and one for Cl^? ion determination, were studied. The Na⁺‐ISEs consisted of a neutral calixarene‐based ionophore and one with a charged carrier dinonylnapthalenesulfonic acid (DNNSA) whereas for the Cl^? ISE, an anion exchanger tridodecylmethylammonium chloride (TDDMA⁺Cl^?), was used. The Na⁺ ISE with DNNSA as the charged carrier was successfully able to discriminate the binding of two different proteins (bovine serum albumin and lysozyme) based on their intrinsic charge.     

Indirect Atomic Absorption Spectrometric Determination of Ammonia,Thiosulfate and Cyanide in an Unsegmented Flow System

Abstract

A flow injection analysis method (FIA), has been developed for the determination of cyanide, thiosulfate and ammonia by atomic absorption spectrometry (AAS). Aqueous solution of the analyte was injected into an on-line column containing glass beads and packed with silver chloride and deionized water was used as the carrier. The analyte dissolves the silver chloride and the dissolved silver complex is introduced to the nebulizer of the AAS. This method has proved to be sensitive, simple and precise. Detection limits of 1.0 × 10^?7 M, 5.0×10^?7 M and 5.0x10^?6M were obtained for thiosulfate, cyanide and ammonia, respectively. The precision of the technique was 2.0%, 2.4% and 1.4% in case of thiosulfate, cyanide and ammonia, respectively. The effects of flow rate and sample volume on the FIA/AAS signals are presented.     

High Performance Liquid Chromatographic Analysis for Free Valine in Plasma

Abstract

A precolumn derivatization method is presented with the use of a fluorescent derivative, 1-dimethylaminonaphhalene-5-sulfonyl-chloride, dansyl chloride, for the detection of free valine in plasma. Dansylated amino acids were determined in deproteinized samples by reverse-phase liquid chromatography. The level of detection is 100 femtoraoles (10^?15). Sample preparation required precipitation of proteins with trichoroacetic acid and removing the excess acid with water saturated ether. The deproteinized sample was adjusted to pH 9.0 and reacted with dansyl chloride. The dansylated products were detected by ultraviolet and fluorescence spectrometry. Elution time for valine subsequent to injection is 25 minutes, while the total assay requires less than 50 minutes.     

Potentiometric flow-injection determination of trace chlorine based on its redox reaction with an iron(III)/iron(II) buffer

A very sensitive and rapid potentiometric determination of trace chlorine in water is described. The method is based on the transient potential changes which appears during the reduction of dissolved chlorin with an iron(III)/iron(II) potential buffer containing chloride and sulfuric acid. The sample is injected into a water carrier stream and merged with a stream of this potential buffer solution; chlorine is reduced during passage through a short reaction coil. The potential change from the baseline is measured with a flow-through ORP (oxidation-reduction potential) electrode. Potential changes (peak heights) are proportional to chlorine concentrations from 10^?7 M to 10^?5 M. The detection limit is 5 × 10^?8 M (3.5 μgl^?1 as Cl₂). The sample throughput is 45 h^?1. Reproducibility is in the range 2.5–1.1%. Results for potable water agree with those obtained by the o-tolidine method.     

Use of a Carbon Paste Electrode Modified with Spinel‐Type Manganese Oxide as a Potentiometric Sensor for Lithium Ions in Flow Injection Analysis

A potentiometric sensor constructed from a mixture of 25% (m/m) spinel‐type manganese oxide (lambda‐MnO₂), 50% (m/m) graphite powder and 25% (m/m) mineral oil is used for the determination of lithium ions in a flow injection analysis system. Experimental parameters, such as pH of the carrier solution, flow rate, injection sample volume, and selectivity for Li⁺ against other alkali and alkaline‐earth ions and the response time of this sensor were investigated. The sensor response to lithium ions was linear in the concentration range 8.6×10^?5–1.0×10^?2 mol L^?1 with a slope 78.9±0.3 mV dec^?1 over a wide pH range 7–10 (Tris buffer), without interference of other alkali and alkaline‐earth metals. For a flow rate of 5.0 mL min^?1 and a injection sample volume of 408.6 μL, the relative standard deviation for repeated injections of a 5.0×10^?4 mol L^?1 lithium ions was 0.3%.     

Determination of Aluminum in Drinking Waters by A.C. Oscillopolarography in a Lithium Chloride System

Abstract

A new and convenient method for the rapid determination of aluminum in drinking waters using a.c. oscillopolarography in a lithium chloride system is described in this paper. The calibration graph is linear from 5 × 10^?6 to 8 × 10^?5 mol/L with a detection limit of 5 × 10^?6 mol/L. The relative standard deviation of the method is 4.7% for 4 × 10^?5 mol/L Al. Compared with other techniques, this method has the significant advantages of simple instrumentation, no deaeration procedure required and rapid measurement. It was particularly suitable to the analysis of 10^?6 ~ 10^?5 mol/L levels of Al in drinking waters.     

Development of Polymeric Membrane Sensor for the Determination of Histamine: Experimental and Theoretical Study

Abstract

Some original histamine membrane sensors were prepared by incorporating thiopyrilium (TP) derivative as an excellent charged carrier. Among these sensors, TP2 shows the best response to histamine in a wide concentration range from 2.5×10^?6 to 1.0×10^?1 mol L^?1 with a slope of 55.6±0.7 mV decade^?1 and with a detection limit of 1.0 µmol L^?1 (～0.1 ppm). The interference between histamine and several amino acids and common inorganic anions was negligible as shown by the potentiometric selectivity coefficient data. The prepared electrode was used for the determination of histamine in a human serum synthetic sample. Theoretical calculations were carried out to find the best interactions between histamine and different ligands.     

A Study of the Permeation of Gold(III) Through Cyanex471x Solid Supported Liquid Membranes (SSLM)

Abstract

A solid supported liquid membrane for the selective removal of Au(III) from chloride solutions has been developed by using Triisobutiphosphine sulfide (Cyanex 471x) In cumene as organic carrier. The membrane system is shown to be effective between chloride solutions ([Cl^?]= 1.0 M) containing traces of Au(III) and SCN^? 0.1 M solutions. Different kinds of at membrane supports have been studied. The results, expressed in terms of membrane permeability, show significant differences between the different supports employed, the polypropylene supports, being the most efficient.     

The Separation and Determination of Molybdenum by Electron Paramagnetic Resonance

Abstract

A procedure is described for the separation and quantitative determination of molybdenum by means of EPR. Molybdenum(VI) was precipitated from a hydrochloric acid solution (1.5 Molar) with α-benzoinoxime. The precipitate was separated by centrifugation and then the sample was dried in an oven at 105°C. Nitrogen was passed over the sample to complete the drying procedure. The precipitate was dissolved in acetonitrile which was 0.5 M in lithium perchlorate. Electrochemical reduction of the sample produced the molybdenum(V) species. The concentration of molybdenum(V) was determined directly from the intensity of the first derivative EPR signal. The range of linearity of the analytical curve was 1.00 × 10^?2 M to 1.00 × 10^?4 M, and a routine accuracy of less than 6% was obtained.     

Application of ion-selective electrodes in environmental analysis : Determination of Acid and Fluoride concentrations in Rain-water with a Flow-Injection System

A flow-injection method is described for the measurement of acid and fluoride concentrations. The conditions were optimized to ensure small sample and reagent consumption, low detection limit and the highest rate of analysis allowed by the potentiometric sensor. With a microcapillary pH-sensitive glass electrode, 20-μl sample volumes and 1.0–1.5 ml min^?1 carrier flow rates, strong acids were determined at concentrations as low as 10^?5 M (0.2 nmol of acid in 20 μ1). The relative standard deviation was about 1% at 10?4 M strong acid concentration at an injection rate of 500–550 h^?1. With a flow- through fluoride-selective electrode, 250-μl sample volumes and a 1 ml min^?1 carrier flow rates, fluoride concentrations as low as 10^?7 M were measured (ca. 0.5 ng of fluoride in 250 μ1). The injection rate was 40 h^?1 at concentrations below 10^?6 M, but 60 h^?1 above 10^?5 M. The methods were used successfully for determining the acid and fluoride concentrations in rain-waters.     

Optimisation of a Flow Injection System with a Piezoelectric Quartz Crystal Detector for the Determination of Inorganic Mercury

ABSTRACT

A new method combining flow injection methodology with quartz crystal microbalance (QCM) detection is proposed for inorganic mercury analysis. A modified simplex method is used in order to maximise the observed analytical signals (crystal frequency decrease). Six parameters were optimised: the concentration of the acidic carrier solution, the lengths of the sample loop and mixing coil, and the flow rates of the sample carrier, the reductant stream (SnCl₂), and the carrier of the mercury vapour (N₂). An increase of 18% in the signal of the centroid of the calibration line was achieved, as well as an increase in the sensitivity from 290 Hz μg^? to 313 Hz μg^?. Following the proposed procedure, detection limits of 47 μg L^? of inorganic mercury were found for sample volumes of 0.5 mL.     

Dioctadecyldimethylammonium Chloride Bilayer Membrane Vesicle-Enhanced and Manganese (II)-Catalyzed Chemiluminescence for Determination of Adrenaline by a Flow-Injection Method

Abstract

A new chemiluminescence system reinforced by use of a surfactant and a metal catalyst is demonstrated for selective determination of adrenaline by a flow-injection method. The weak light emission originating from an aerobic oxidation of adrenaline in an alkaline solution is dramatically enhanced by ordered surfactant molecular assemblies, dioctadecyldimethylammonium chloride bilayer membrane vesicles, with the largest enhancement factor of 1000 which has not ever been realized. The enhanced emission is further increased by a Mn(II) catalyst with an enhancement factor of ca. 40. The limit of determination(S/N=2) is 1×10^?8M (0.2 ng in 100-μ1 injection), the linear range is four ordrers of magnitude, the sample throughput is 100 h^?1. and the relative standard deviation(n=5) is 0.9 % for 5×10^?7M adrenaline. Of other substances including dopamine, noradrenaline, and related compounds, p-hydroxymandelenic acid chemiluminesces most strongly after adrenaline, the 1×10^?3M solution providing a signal 24% of that for 1×10^?6M adrenaline.     

Membrane-dialyzer injection loop for enhancing the selectivity of anion-responsive liquid-membrane electrodes in flow systems Part 2. A selective sensing system for salicylate

An electrode-based flow-injection system suitable for the direct determination of salicylic acid is described. The system utilizez a tubular polymer membrrane electrode based on manganese(III) tetraphenylporphyrin chloride to sense salicylate ions formed in a recipient buffer solution held within the upper channel of a flow-through membrane dialyzer assembly. Samples containing salicylic acid are manually intoduced into the lower channel of the dialysis unit, in which a thin silicone rubber membrane separates the two channels. The analyte is trapped across the membrane as salicylate ions within a static layer of an appropriate recipient buffer. After a fixed trapping time, the recipient plug is flushed to the electrode in a conventional flow-injection manner. Peak potentials observed are logarithmically related to the salicylic acid concentrations in the original sample. Without the dialysis unit, the electrode response to salicylate is nearly Nernstian over the range 2 × 10^?6?10^?2 M. In the complete flow/dialysis system, near Nernstian response was achieved for 10^?4?10^?2 M salicylate with a 2-min trapping time. Detection limits can be altered by changing the trapping time. Anionic salicylate can be determined by acidifying the sample. The resulting system offers very high selectivity for salicylate (as salicylic acid) over most inorganic and organic anions normally found in blood. Preliminary studies demonstrate the practical application of this system for the determination of salicylate in serum.     

Continuous dialysis of hydrochloric acid and lithium chloride: permeability of anion-exchange membrane to chloride ions

A counter-current two-compartment dialyzer equipped with an anion-exchange membrane Neosepta-AFN was used to study dialysis of a hydrochloric acid and lithium chloride mixture. To quantify this process, several characteristics were calculated from the data obtained at steady state. First, the dialysis process was characterized by the acid recovery yield and rejection coefficient of salt, which were in the range of 61–98% and 62–94%, respectively (for HCl and LiCl concentrations from 0.1 to 1.0 kmol m^?3 and volumetric liquid flow rates from 8 × 10^?9 to 24 × 10^?9 m³ s^?1). Furthermore, this study proved that dialysis of an HCl + LiCl mixture can be quantified by a single characteristic, i.e., the permeability coefficient of the membrane to chloride ions, which is a function of the concentration of both the components in the feed.     

Atomicm absorption spectrometric determination of the isotopic composition of lithium by an ultimate absorbance-ratio technique

The conventional absorbance-ratio technique for determining the isotopic composition of lithium by atomic absorption spectrometry is improved by the use of “ultimate absorbance ratios” of sample solutions. These ratios are obtained by extrapolating the linear portion of lithium content/absorbance-ratio plots to the intercept at 0 mol m^?3 lithium. These graphs are obtained measuring the absorbances of solutions of known ⁶Li abundance and of various lithium contents with natural and ⁶Li-enriched lithium hollow-cathode lamps. Linear calibration is attained over the range 0.0–99.3% ⁶Li, and the lithium isotopic abundance can be determined with an absolute error of ±0.7% ⁶Li for > 0.01 mol m^?3 lithium solutions. The method requires neither prior measurement of the total lithium content in sample solutions nor adjustment of the content to match that in the standard solutions.     

Synthesis of networked polymers by copolymerization of monoepoxy‐substituted lithium sulfonylimide and diepoxy‐substituted poly(ethylene glycol), and their properties

Networked polymers that had poly(ethylene glycol) (PEG) chains and lithium sulfonylimide salt structures were prepared by curing a mixture of poly(ethylene glycol) diglycidyl ether and lithium 3‐glycidyloxypropanesulfonyl‐trifluoromethanesulfonylimide with poly(ethylene glycol) bis(3‐aminopropyl) terminated. The obtained flexible self‐standing networked polymer films showed high thermal and mechanical stability with relatively high ionic conductivity. The room temperature ionic conductivity under a dry condition was in the range of 10^?5 ～ 10^?4 S m^?1, which is one order of magnitude higher than the corresponding networked polymers having lithium sulfonate salt structures (10^?6 ～ 10^?5 S m^?1). The film sample became swollen by immersing in propylene carbonate (PC) or PC solution of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The sample swollen in PC showed higher ionic conductivity (7.2 × 10^?3 S m^?1 at room temperature), and the sample swollen in 1.0 M LiTFSI/PC showed much higher ionic conductivity (8.2 × 10^?1 S m^?1 at room temperature). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Selective substoichiometry for inorganic arsenic(V) by ion-pair extraction with pyrogallol/tetraphenyl-arsnium chloride and its application in the analysis of seaweed

Arsenic(V) is substioichiometrically extracted from 0.4–3 M sulfuric acid solutions into 1,2-dichloroethane with 1.0 × 10^?5 M teraphenylarsnium chloride in the presence of 2.0 × 10^?1 M pyrogallol. Reproducibility of the substoichiometric extractions with a constant amount of tetraphenylarsonium chloride is high (0.5% RSD). This substiochiometric extraction is very selective for arsenic(V) from arsenic(III), monomethylarsonic acid, and dimethylarsinic acid. The extraction combined with the isotope dilution principle was applied to the determination of arsenic(V) in an acid-digestd solution of a seaweed sample (Laminaria religiosa Miyabe) and to the determination of total arsenic in this sample.     

Determination of indium in geological materials by electrothermal-atomization atomic absorption spectrometry with a tungsten-impregnated graphite furance

The sample is fused with lithium metaborate and the melt is dissolved in 15% (v/v) hydrobromic acid. Iron(III) is reduced with ascorbic acid to avoid its coextraction with indium as the bromide into methyl isobutyl ketone. Impregnation of the graphite furnace with sodium tungstate, and the presence of lithium metaborate and ascorbic acid in the reaction medium improve the sensitivity and precision. The limits of determination are 0.025–16 mg kg^?1 indium in the sample. For 22 geological reference samples containing more than 0.1 mg kg^?1 indium, relative standard deviations ranged from 3.0 to 8.5% (average 5.7%). Recoveries of indium added to various samples ranged from 96.7 to 105.6% (average 100.2%).     

Calorimetric Determination of Phosphorylated Serum Cholinesterase and Its Reactivation by an Antidote

Abstract

Serum cholinesterase, inhibited in vitro up to 92% by 0, 0 dimethyl-2, 2-dichlorovinyl phosphate (4.52 × 10^?9 mole/ml of 40% serum), was reactivated up to 35% with 2-pyridine aldoxime methiodide (3.5 × 10^?6 mole/ml of 40% serum). Evaluation was based on the reaction rate between cholinesterase and acetylcholine chloride (2.2 × 10^?6 mole) measured with a microcalorimeter. It was thus possible to approximate the “normal” or pre-exposure level of serum cholinesterase, while simultaneously determining the extent of poisoning.