Ir和IrPd催化剂的合成及结构调控对其甲醇氧化性能的影响

以三嵌段共聚物P123(聚环氧乙烷-聚环氧丙烷-聚环氧乙烷,PEO₂₀-PPO₇₀-PEO₂₀)为还原剂和保护剂,比较了水热法和溶剂热法对纯Ir和IrPd合金催化剂合成及其电催化氧化甲醇(MOR)性能的影响。对于纯Ir催化剂,在相同条件下,溶剂热法能更好地促进Ir前驱体的还原。对于IrPd合金催化剂,溶剂热法可制得表面富含Ir但MOR活性较低的核壳结构产物(IrPd-S)。水热反应得到的不同原子比(IrPd、Ir₂Pd、IrPd₂)的产物粒径更小,元素分布更均匀。其中比例为1∶1的IrPd (IrPd-H)催化剂的MOR电催化活性最高。上述结果表明,通过调节溶剂类型以及P123的结构诱导作用,可以有效地调节纯Ir和IrPd合金催化剂的结构、表面组成和电催化活性。     

纳米钯催化剂对甲醇的电催化氧化

采用水热法,以甲醛作还原剂还原Pd2+-EDTA络合物,制得钛基纳米钯颗粒电极(nanoPd/Ti).扫描电子显微镜(SEM)显示,纳米钯颗粒直径约为60 nm,形成三维立体网状结构.在碱性溶液中,循环伏安及交流阻抗测试分别表明:nanoPd/Ti电极对甲醇氧化有极高的阳极电流、较低的起始氧化电位和较强的抗CO毒化能力.在nanoPd/Ti电极上甲醇电氧化反应的阻抗值较低,增加甲醇浓度,电极阻抗更低.电极对甲醇氧化具有极好的电催化活性.     

镧对钯催化剂上甲醇深度氧化反应性能的影响

在色谱-微反装置上考察了负载型Pd催化剂上甲醇深度氧化反应的性能，结果表明，在氧化铝载体中，添加稀土元素La对Pd催化剂的催化性能有较大的影响。反应气中不合CO时，La虽不能使用甲醇的起燃温度降低，但含氧中间物含量可以大大降低；在反应气中含CO时，La的存在可明显降低甲醇的起燃温度，并能显著削弱CO对甲醇氧化反应的干扰，La的加入能减少CO在催化剂上的吸附量，并能改变Pd的电子结构，而电子结构的改变与催化性能的变化有着对应的关系。     

甲醇燃料车尾气净化催化剂的研究Ⅱ.负载钯催化剂对甲醇低温深度氧化性能的研究

利用色谱微反联用技术对负载钯催化剂上甲醇、甲醛的深度氧化进行了较全面的研究。结果表明：Ｐｄ／Ａｌ２Ｏ３催化剂对甲醇氧化具有很高的转化效率和一定的深度氧化活性。以（ＮＨ４）２ＰｄＣｌ４为浸渍液、还原气氛下焙烧所得的０．１％Ｐｄ／γＡｌ２Ｏ３性能最好，当进气Ｏ２／ＣＨ３ＯＨ比为６、并无ＣＯ存在时，其Ｔ５０、Ｔ９５分别为９０℃、２００℃，生成甲醛的最高转化率为１７％左右。另外，反应原料气组分如Ｏ２、ＣＯ等也将严重影响Ｐｄ／γＡｌ２Ｏ３对甲醇氧化的活性及选择性。     

氧化乙烯、苯乙烯和甲基丙烯酸甲酯星型ABC三嵌段共聚物的合成和表征

报道了一个有普遍意义的合成氧化乙烯(EO)、苯乙烯(St)和甲基丙烯酸甲酯(MMA)ABC星型三嵌段共聚物(S-PEO-PS-PMMA)的方法.聚氧化乙烯(PEO)嵌段是由Schiffs碱保护的胺基苯酚钾引发环氧乙烷开环后得到的,在去保护后,PEO的苯胺端基在光的作用下,和二苯酮组成电荷转移络合物,分别引发St和MMA聚合.生成的S-PEO-PS-PMMA可以通过薄层色谱(TLC)和含芳亚胺基团的双嵌段共聚物PEO-b-PS分离,用IR,NMR,GPC和裂解气相色谱(PGC)对产物结构进行了详细的表征.     

三维结构氧化石墨烯载铂催化剂对甲醇电催化性能

喷雾干燥法制备具有三维结构的氧化石墨烯(PGO),在其表面进一步负载活性成分Pt,得到纳米Pt/PGO复合催化剂。采用X射线粉末衍射(XRD)、透视电镜(TEM)和扫描电镜(SEM)等对催化剂的形貌和结构进行表征。结果表明,PGO具有类似于长4-6μm和宽2.0-3.0μm的三维纸团结构,平均粒径为4.2 nm的Pt纳米粒子均匀分布在其表面。采用循环伏安和计时电流法研究了在酸性溶液中催化剂对甲醇的电催化氧化性能。结果表明,Pt/PGO催化剂对甲醇呈现出更高的电催化氧化活性和稳定性。PGO所具有的三维结构和双功能作用机理有利于甲醇在铂表面的电催化氧化过程的发生。     

一维/二维复合碳载体组成对Pd催化剂甲醇氧化性能的影响

采用固相-液相两步混合法制备了由碳纳米管（CNTs）和石墨烯纳米片（GNPs）组成的CNTs-GNPs复合载体。以乙二醇还原法将Pd纳米粒子沉积于复合碳载体上,制得Pd/CNTs-GNPs催化剂。以透射电子显微镜、X射线衍射及X射线光电子能谱表征催化剂的形貌、组成和结构;以电化学方法考察催化剂的甲醇电氧化性能。结果表明,Pd/CNTs-GNPs（1/4）（GNPs质量分数为1/4）催化剂具有较大的电化学表面积和较高的甲醇电氧化活性,其甲醇氧化峰电流密度可达Pd/CNTs催化剂的1.97倍。催化剂的高活性得益于CNTs-GNPs载体的一维/二维复合结构使Pd纳米粒子具有良好的分散性能。计时电流实验表明,与单一载体负载Pd催化剂相比,复合载体负载Pd催化剂具有较强的抗中毒能力。     

镧对钯催化剂上甲醇深度氧化反应性能的影响

大色谱－微反装置上考察了负载型Ｐｄ催化剂上甲醇深度氧化反应的性能,结果表明,在氧化铝载体中,添加稀土元素Ｌａ对Ｐｄ催化剂的催化性能有较大的影响,反应气中不含ＣＯ时,Ｌａ虽不能使甲醇的起燃温度降低,但含氧中间物含量可以大大降低;在反应气中含ＣＯ时,Ｌａ的存在可明显降低甲醇的起燃温度,并能显者削弱ＣＯ对甲醇氧化反应的干扰,Ｌａ主能减少ＣＯ在催化剂上的吸附量,并能改变Ｐｄ的电子结构,而电子结构的改变与催化性能的变化有着对应的关系。     

Role of the structural and electronic properties of molybdenum trioxide catalysts on the structure-sensitive oxidation of methanol to formaldehyde

Summary As catalysts for selective oxidation, molybdenum trioxide catalysts—prepared by two different methods—have been investigated. The results of vapor-phase oxidation of methanol are discussed on the basis of the acidic property, oxidizing functions, and the crystallographic structure of the catalysts. It was found that the acidic property is not the sole factor deciding the catalytic activity. Electrical conductivity measurements proved that molecular oxygen in the gas feed is necessary for maintaining the catalysts active. The difference in the catalytic activity and selectivity were reasonably interpreted in view of the structure sensitivity of those catalysts. A redox mechanism is also discussed in this paper.

---

Der Einfluß von strukturellen und elektronischen Eigenschaften von Molybdäntrioxidkatalysatoren auf die struktursensitive Oxidation von Methanol zu Formaldehyd

Zusammenfassung Auf zwei verschiedene Arten hergestellte Molybdäntrioxidkatalysatoren wurden für selektive Oxidationen untersucht. Die Ergebnisse der Dampfphasenoxidation von Methanol werden auf Basis der sauren Eigenschaften, der oxidierenden Funktionen und der kristallographischen Struktur der Katalysatoren diskutiert. Es wurde festgestellt, daß die sauren Eigenschaften zur Erklärung der entscheidenden Wirksamkeit der Katalysatoren nicht alleine verantwortlich sind. Elektrische Leitfähigkeitsmessungen zeigten, daß molekularer Sauerstoff im zugeleiteten Gas zur Erhaltung der katalytischen Aktivität notwendig ist. Die Unterschiede in der Katalysatoraktivität und der Selektivität sind aus der Struktur der Katalysatoren zu erklären. Es wird ein adäquater Redox-Mechanismus diskutiert.

     

还原剂对Au-Pd/CeO2催化剂甲醇部分氧化性能的影响

以PVP为保护剂,乙醇(ER)、乙二醇(GR)和水合肼(HR)为还原剂制备了一系列Au-Pd/CeO2催化剂,考察了还原剂对甲醇部分氧化性能的影响,并运用XRD、TPD和TPR等手段对催化剂进行了表征。结果表明,Au-Pd/CeO2(ER)催化剂具有较大的比表面积,形成的AuxPdy量较多、粒径较小、分散度较高、活性组分与载体的相互作用较强,同时对甲醇的吸附量较大和吸附温度较低。因此,该催化剂具有较高的催化活性和氢气选择性以及较低的CO质量分数。     

壳聚糖修饰炭黑负载Pt-Au催化剂对甲醇氧化的电催化性能

以炭黑及自制的壳聚糖-炭黑(CHI-C)复合材料为载体,采用溶胶负载法制备了Pt_m＾Au/C及Pt_m＾Au/CHI-C催化剂(＾ 代表Au、Pt为分步负载,m代表Pt/Au原子比),通过紫外-可见吸收光谱、X射线衍射、透射电镜及X射线光电子能谱对催化剂进行了表征。利用循环伏安法和计时电流法分别测定了Pt-Au催化剂对甲醇电催化氧化反应的活性和稳定性,考查了Pt/Au原子比及CHI改性对电催化活性和稳定性的影响。结果表明,Pt_1.0＾Au/C具有最高的催化活性,炭黑中加入少量CHI能提高Pt_1.0＾Au/C催化剂的稳定性。     

不同改性组分对Cu-ZnO基催化剂低温甲醇合成性能的影响

通过共沉淀法制备了Al、Zr和Ce改性的Cu-ZnO基低温甲醇合成催化剂,采用氮气物理吸附、H2-TPR、CO2-TPD、N2O滴定、XRD和TEM等技术对其进行了表征,并考察了改性组分和煅烧温度对其在170℃下合成气制甲醇催化性能的影响。结果表明,经Zr改性的Cu-ZnO基催化剂,其低温甲醇合成性能较好;随着煅烧温度的降低,Cu在催化剂表面的分散度逐渐变大、颗粒逐渐变小,所得到的催化剂其活性也较高;其中,未经煅烧的Cu-ZnO/ZrO2催化剂的活性最佳,其甲醇时空产率为106.02 g/(kg·h),选择性达87.04%。     

Development of high performance Cu/ZnO-based catalysts for methanol synthesis and the water-gas shift reaction

Our groups studies on Cu/ZnO-based catalysts for methanol synthesis via hydrogenation of CO₂ and for the water-gas shift reaction are reviewed. Effects of ZnO contained in supported Cu-based catalysts on their activities for several reactions were investigated. The addition of ZnO to Cu-based catalyst supported on Al₂O₃, ZrO₂ or SiO₂ improved its specific activity for methanol synthesis and the reverse water-gas shift reaction, but did not improve its specific activity for methanol steam reforming and the water-gas shift reaction. Methanol synthesis from CO₂ and H₂ over Cu/ZnO-based catalysts was extensively studied under a joint research project between National Institute for Resources and Environment (NIRE; one of the former research institutes reorganized to AIST) and Research Institute of Innovative Technology for the Earth (RITE). It was suggested that methanol should be produced via the hydrogenation of CO₂, but not via the hydrogenation of CO, and that H₂O produced along with methanol should greatly suppress methanol synthesis. The Cu/ZnO-based multicomponent catalysts such as Cu/ZnO/ZrO₂/Al₂O₃ and Cu/ZnO/ZrO₂/Al₂O₃/Ga₂O₃ were highly active for methanol synthesis from CO₂ and H₂. The addition of a small amount of colloidal silica to the multicomponent catalysts greatly improved their long-term stability during methanol synthesis from CO₂ and H₂. The purity of the crude methanol produced in a bench plant was 99.9 wt% and higher than that of the crude methanol from a commercial methanol synthesis from syngas. The water-gas shift reaction over Cu/ZnO-based catalysts was also studied. The activity of Cu/ZnO/ZrO₂/Al₂O₃ catalyst for the water-gas shift reaction at 523 K was less affected by the pre-treatments such as calcination and treatment in H₂ at high temperatures than that of the Cu/ZnO/Al₂O₃ catalyst. Accordingly, the Cu/ZnO/ZrO₂/Al₂O₃ catalyst was considered to be more suitable for practical use for the water-gas shift reaction. The Cu/ZnO/ZrO₂/Al₂O₃ catalyst was also highly active for the water-gas shift reaction at 673 K. Furthermore, a two-stage reaction system composed of the first reaction zone for the water-gas shift reaction at 673 K and the second reaction zone for the reaction at 523 K was found to be more efficient than a one-stage reaction system. The addition of a small amount of colloidal silica to a Cu/ZnO-based catalyst greatly improved its long-term stability in the water-gas shift reaction in a similar manner as in methanol synthesis from CO₂ and H₂.     

Effect of preparation methods of aluminum emulsions on catalytic performance of copper-based catalysts for methanol synthesis from syngas

Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their performances for methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS, N2 adsorption--desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu⁰ surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate (NP) exhibited the best catalytic performance for methanol synthesis from syngas.     

One-step synthesis of porous PtNiCu trimetallic nanoalloy with enhanced electrocatalytic performance toward methanol oxidation

Pt-based alloy nanoporous structures have attracted a lot of attention because of their high activity and stability toward alcohol oxidation reactions. Especially, Pt alloying with Earth-abundant metal can lower the cost of catalyst. Here, we introduce a one-pot approach to synthesize bimetallic PtCu and Ni-doped PtCu nanoalloy with porous structure. The as-synthesized Ni-doped Pt₆₀Ni₃Cu₃₇ nanoalloys exhibit excellent electrocatalytic properties toward methanol oxidation in acidic medium. The mass activity of the as-synthesized Pt₆₀Ni₃Cu₃₇ nanoalloys is 3.6 times and 5.3 times that of Pt₅₅Cu₄₅ nanoalloys and commercial Pt black for methanol oxidation in 0.2?M methanol solution. Besides, the stability of the as-synthesized Pt₆₀Ni₃Cu₃₇ nanoalloys was much better than Pt₅₅Cu₄₅ nanoalloys and commercial Pt black. After 3600?s chronoamperometry test, the remaining values of the Pt₆₀Ni₃Cu₃₇ nanoalloys are 3.7 times and 11.0 times that of Pt₅₅Cu₄₅ nanoalloys and commercial Pt black. And it is the first time to report that small amount of Ni dopants can boost the activity and stability of PtNiCu alloys toward methanol oxidation.     

锆助剂对低温液相合成甲醇用铜铬硅催化剂性能的影响

考察了含锆的铜铬硅催化剂低温液相合成甲醇性能，并进行了BET、TPR-H2、TPD-H2、TPD-CO、XRD和XPS表征。结果表明，锆作为结构助剂及电子助剂对催化剂在低温液相合成甲醇反应中具有显著的促进作用，反应活性可提高32.25 ％。锆助剂能有效提高催化剂的比表面积，促进催化剂中铜铬组分的分散及表面富集。ZrO2加入在催化剂表面产生的Cu+与催化活性的改善密切相关，Zr4+、Cr3+、Cu+可形成复合中心，为价态的稳定性提供微环境，在H2活化及C O键的断裂等反应步骤中起重要作用。     

Promoting effect of polyoxyethylene octylphenol ether on Cu/ZnO catalysts for low-temperature methanol synthesis

Cu/ZnO catalysts were prepared by the co-precipitation method with the addition of OP-10 (polyoxyethylene octylphenol ether) and were chemically and structurally characterized by means of XRD, BET, H₂-TPR, CO-TPD and N₂O-titration. The effect of OP-10 addition on the activity of Cu/ZnO for the slurry phase methanol synthesis at 150 °C was evaluated. The results showed that Cu/ZnO prepared with addition of 8% OP-10 (denoted as C8) exhibited the promoted activity for the methanol synthesis. The conversion of CO and the STY (space time yield) of methanol were 42.5% and 74.6% higher than those of Cu/ZnO prepared without addition of OP-10 (denoted as C0), respectively. The precursor of C8 contained more aurichalcite and rosasite, and the concerted effect of Cu-Zn in C8 was found to be stronger than that in C0. Compared with C0, C8 showed smaller particle size, lower reduction temperature and larger BET and Cu surface areas.