Application of the Ugi reaction for the preparation of enzyme electrodes

Glucose oxidase and catalase were immobilized via the Ugi reaction by means of cyclohexyl isocyanide and glutaraldehyde on a nylon net partially hydrolysed by hydrochloric acid. A specific enzyme sensor for D-glucose was made by fixing the nylon net with immobilized enzymes on the tip of a Clark-type oxygen sensor. For comparison purposes glucose oxidase and catalase were also co-immobilized in the absence of cyclohexyl isocyanide or only glucose oxidase was immobilized with and without cyclohexyl isocyanide. The prepared biosensors were characterized by the specific activity of glucose oxidase and its dependence on Ph and temperature and by the apparent Michaelis constant. The linear range of the biosensor response to the substrate concentration and the stability of the biosensor were determined. The long-term stabilities of the enzyme electrodes were compared and the advangtage of the developed method was demonstrated.     

The ammonia freeze explosion (AFEX) process

A partially purified phophotriesterase was successfully immobilized onto nylon 6 and 66 membranes, nylon 11 powder, and nylon tubing. Up to 9000 U of enzyme activity was immobilized onto 2000 cm2 of a nylon 6 membrane where 1 U is the amount of enzyme necessary to catalyze the hydrolysis of 1.0 mumol of paraoxon/min at 25 degrees C. The nylon 66 membrane-bound phosphotriesterase was characterized kinetically where the apparent Km value for the immobilized enzyme was 0.35 mM. This is 5-6 times higher than that observed for the soluble enzyme. However, nylon immobilization limited the maximum rate of paraoxon hydrolysis to less than 10% of the value measured for the soluble enzyme. The addition of the cosolvent, methanol, resulted in an increase in the apparent Km value for paraoxon hydrolysis but concentrations up to 40% had no negative effect on the catalytic effectiveness with the soluble or immobilized phosphotriesterase. Based on the kinetic analysis, methanol appears to be a competitive inhibitor for both forms of enzyme. The nylon powder immobilized enzyme was shown to be stable for at least 20 mo. The immobilization of the phosphotriesterase onto nylon provides a practical method for the detoxification of organophosphate pesticides.     

Immobilization of binding proteins on nonporous supports

Four different nonporous particulate materials, nylon, polystyrene, soda-lime silicate glass, and fused silica glass, have been evaluated for their appropriateness as immobilization supports for immunoglobulins. A method of protein quantitation that is usually applied to solutions, the bicinchoninic acid (BCA) assay, was used successfully to directly measure ng amounts of protein immobilized on the supports. Two proteins, a monoclonal antibody to theophylline and the biotin binding protein avidin, were studied. Radioactive theophylline and radioactive biotin were used to measure the activity of the immobilized protein. Ligand binding capacity per mm2 of support was measured as a function of amount of protein immobilized. By measuring both the amount of protein immobilized and its ligand binding capacity, we have determined that antitheophylline antibody adsorbed on polystyrene balls loses almost 90% of its binding activity after 65 h, although little protein is lost from the balls over this time. Avidin retains nearly full activity for biotin on polystyrene. The binding activity of biotinyl-antibody conjugate immobilized on avidin-adsorbed polystyrene is stable, even when stored for over 22 wk. Antibody covalently immobilized on soda-lime silicate glass beads retains its binding activity over long-term storage, although only 0.1 mol of 3H-theophylline bind per mol of immobilized antibody. Using fused silica glass particles as the solid support, the same antibody binds approx 0.6 mol of ligand per mol of immobilized antibody protein. The structural "softness" of the immunoglobulin requires that interaction with the surface be prevented in order to maintain activity.     

尼龙亲和膜色谱法纯化半胱氨酸蛋白酶抑制剂

建立了一种快速、简便的分离半胱氨酸蛋白酶抑制剂的方法,尼龙膜经壳聚糖改性后,以木瓜蛋白酶为配基制备了一种新型的蛋白质分离材料,并研究了此分离材料的物理及化学性能。所得到的亲和膜上固定化木瓜蛋白酶的热稳定性提高,最适催化温度为55℃,最适pH值为8.0,米氏常数为353.8 g/L;将该亲和膜应用于半胱氨酸蛋白酶抑制剂的分离纯化,在对洗脱液、洗脱速度进行优化的基础上,成功的分离纯化出半胱氨酸蛋白酶抑制剂,纯化倍数为7.25倍。     

固定化酶在生物医学上的应用(Ⅰ)——聚丙烯酰胺固定化尿酶的制备及性能

本文以交联聚丙烯酰胺对尿酶包埋进行了研究,制备出了球形固定化尿酶,其含酶量高(1份酶对1份聚合物),相对活性为50%左右,对尿素的分解活性:120m/ml(固定化尿酶,37℃,2小时),提高了稳定性,在4℃下,66天后活性降低8%,106天后活性降低22%,37℃下11天后活性降低18%,并且不泄漏酶。基于以上特点,该固定化尿酶为吸附型人工肾提供了一个较合适的活性材料。     

The use of immobilized alcohol oxidase in the continuous flow determination of ethanol with an oxygen electrode

Immobilized alcohol oxidase was used in the determination of blood alcohol. The alcohol oxidase catalyzed the aerobic oxidation of ethanol and the oxygen concentration was monitored with an oxygen membrane electrode in a flow cell. The enzyme was immobilized either by covalent attachment via glutaraldehyde to the inside walls of nylon tubing, or by adsorption onto three separate controlled-pore glass support materials: TiO₂, SiO₂, or AL₂O₃. The supports were packed into 10 cm lengths of 3 mm i.d. glass tubing or 30 cm lengths of 5 mm i.d. nylon tubing. The five methods of immobilization were compared for stability and activity toward ethanol. Immobilization on silanized glass beads results in the highest activity and greatest stability of the reactor.     

The selective immobilization of ceruloplasmin onto the chromatographic material used for its purification

Summary When mammalian plasma was passed through a chromatographic material containing aminoethyl functional groups, ceruloplasmin was selectively retained. At a specific ionic strength of the eluant buffer, a single chromatographic peak corresponding to the electrophoretically homogeneous purified ceruloplasmin was eluted. This single-step procedure is easy to perform and gave a purification yield of more than 60%. The direct immobilization of the ceruloplasmin, while it was still adsorbed and concentrated at the basal part of the gel bed (last stage of the purification), was achieved by carbodiimide treatment, with coupling yields of 50–70%.The immobilized ceruloplasmin retained about 100% of its enzymatic activity. Kinetic studies have shown a decreased affinity of the immobilized protein for the substrate and a maximal velocity of 81% as compared to the free protein. The immobilized ceruloplasmin was much more resistant to proteolytic attack than the free enzyme which is highly protease sensitive. Using pronase and thermolysine proteases, the activity of free ceruloplasmin was entirely lost in few hours. However, under similar conditions, the immobilized ceruloplasmin exhibited a high stability, maintaining its integral activity even after 24 hours of proteolytic attack.     

介孔材料MCFs的合成及组装青霉素酰化酶的性质研究

介孔材料由于具有纳米级规则孔道和巨大的比表面积而在催化、吸附及分离等方面存在较大的应用价值．近年来,由介孔分子筛如MCM-41和SBA-15州等组装功能性材料已成为研究的热点．酶作为高效催化剂有许多优点,但在溶液中易失活,使用后无法回收,有的酶在溶液中还存在自水解问题：将酶组装在介孔材料中制成固定化酶则可解决上述问题．目前已成功地将辣根过氧化物酶     

Immobilization of a lactase onto a magnetic support by covalent attachment to polyethyleneimine-glutaraldehyde-activated magnetite

A magnetic immobilized lactase has been prepared using magnetite as the magnetic material. Magnetite was functionalized by treatment with polyethyleneimine and crosslinked with glutaraldehyde. Lactase was then covalently coupled to the activated magnetic matrix via the aldehyde groups. The conditions for optimal immobilization of enzyme are described. Eighty percent of the lactase activity was lost on immobilization and is thought to be owing to the orientation of enzyme binding to the matrix. The amount of protein coupled was 80% of that applied. The maximum lactase activity retained on the matrix following immobilization was 360 U/g matrix. The immobilized lactase showed optimal activity at pH 4.5 and 65 degrees C. The immobilized lactase was more heat stable than the free enzyme, and retained 83% of its original activity after 14 d at 55 degrees C. Galactose competitively inhibited the immobilized lactase preparation (Ki 20 m/M). The presence of high initial concentrations of galactose (10% w/v) did not prevent total hydrolysis of lactose. Glucose and calcium ions were activators of the immobilized enzyme. The immobilized enzyme hydrolyzed high concentrations of lactose (up to 25% w/v) to completion within 4-6 h in a stirred batch reactor at 55 degrees C. There was no evidence of substrate inhibition at high substrate concentrations. The efficiency of hydrolysis of lactose by the immobilized lactase was better than that of the free enzyme. The magnetic immobilized lactase was demonstrated to be suitable for use in the enzymatic hydrolysis of both pure, and cheese whey permeate, lactose.     

A Fiber Optic Lactate Biosensor with an Oxygen Optrode as the Transducer

Abstract

A biosensor for continuous determination of lactate is presented. Lactate monooxygenase was immobilized covalently on nylon membranes, and the consumption of oxygen was measured by following, via a fiber optic bundle, the changes in the fluorescence of an oxygen-sensitive dye dissolved in 10- and 25-um silicone membranes placed beneath the enzyme layer. Oxygen is consumed as a result of the oxidation of lactate by the enzyme, and the decrease in its partial pressure is indicated by the fluorescent dye. For two types of sensors (with different nylon membranes and different thicknesses of the indicator layer) the analytical ranges were 2–50 mM and 0.3–6.0 mM, with response times (t₉₀) of 2.3–3.0 and 4.0–6.0 min, respectively.     

Electrical Control of Urease Activity Immobilized to the Conducting Polymer on the Carbon Felt Electrode

The activity of urease varies by its redox reaction. Active urease has an SH group that is essential to exhibit its activity, however, oxidation agents such as quinone compounds can oxidize the SH group in urease and a S–S bond is produced, resulting in the loss of enzyme activity. The reduction potential of cystine was almost the same as that of the recovery of urease activity. In this work, it has been found that the SH group of urease can be oxidized by not only chemical reaction but also by the direct electrode oxidation of urease and the produced S–S bond can be reduced to SH group by chemical and electrode reactions, and the original enzyme activity is recovered. This research shows that the regulation of urease activity is easily possible by changing the electrode potential of the porous carbon felt immobilized urease. The variation of urease activity was monitored by ammonia or carbon dioxide electrode equipped with the urease immobilized carbon felt, and the ammonia or carbon oxide generated from urea can transfer through the carbon felt to reach the each gas permeable membrane. The combination of gas electrode with porous conducting material such as carbon can supply the novel device for the electrochemical investigation of enzyme activity.     

A Trypsin Immobilized Sol-Gel for Protein Indentification in MALDI-MS Applications

The proteolytic enzyme trypsin was chemically immobilized to an amine-functionalized sol-gel using adipoyl chloride under nonaqueous conditions and a nitrogen atmosphere. In the synthesis of the sol-gel, tetraethyl orthosilicate (TEOS), and 3-(2-aminoethylamino) propyldimethoxymethylsilane (AEAPMS) (50:50, v/v) were used, which provided convenient physical and chemical conditions to maintain catalytic activity of immobilized trypsin molecules for the digestion of proteins in proteomics applications. Bovine serum albumin was used as a model protein to perform enzymatic digestion using the trypsin immobilized sol-gel. The resulting peptides were analyzed by matrix-assisted laser desorption/ionization-mass spectrometry to evaluate the digestion performance and specificity of the sol-gel material. The trypsin immobilized sol-gel showed superior enzymatic activity in protein digestion and it was determined that the sol-gel material could be repeatedly used at least 25 times without significant activity loss in long-term use. Additionally, autocatalysis was prevented by immobilization of trypsin. The peptide digest having the highest purity was obtained for protein identification studies.     

介孔分子筛SBA-15中α-胰凝乳蛋白酶组装及催化活性研究

介孔分子筛由于规则孔道或笼的存在 ,使其具有择形催化作用、高比表面积和强吸附性能 ,其孔道中可组装多种物质而改变其理化性能 .Thomas等 [1] 在介孔 Si O2 上接枝金属茂复合物 .白妮 [2 ] 和张雪峥 [3 ] 等分别将脂溶性金属酞菁衍生物和杂多酸封装在介孔分子筛中 ,得到的组装体催化性能优良 .近年来由于不断合成出 MCM- 41 [4 ] 和 SBA- 1 5 [5] 等孔径较大的介孔分子筛 ,使在介孔材料孔道中组装生物大分子成为可能 .Yen等 [6] 将细胞色素 c组装到孔道中 ,并使酶的稳定性得到提高 ,而α-胰凝乳蛋白酶 (Mr=2 5 0 0 0 ,分子动力学直径…     

Immobilization of glutaryl-7-aminocephalosporanic acid acylase on silica gel and enhancement of its stability

Glutaryl-7-aminocephalosporanic acid (GL-7-ACA) acylase isan enzyme that converts GL-7-ACA to 7-aminocephalosporanic acid, a starting material for semisynthetic cephalosporin antibiotics. In this study, optimal conditions for the immobilization of GL-7-ACA acylase were determined by experimental observations and statistical methods. The optimal conditions were as follows: 1.1 M phosphate buffer (pH 8.3) as buffer solution, immobilization temperature of 20°C, and immobilization time of 120 min. Unreacted aldehydegroups were quenched by reaction with a low-molecular-weight material such as l-lysine, glycine, and ethanolamine after immobilization in order to enhance the activity of immobilized GL-7-ACA acylase. The activities of immobilized GL-7-ACA acylase obtained by using the low-molecular-weight materials were higher than those obtained by immobilized GL-7-ACA acylase not treated with low-molecular-weight materials. In particular, the highest activity of immobilized GL-7-ACA acylase was obtained using 0.4% (v/v) ethanolamine. We also investigated the effect of sodium cyanoborohydride in order to increase the stability of the linkage between the enzyme and the support. The effect on operational stability was obvious: the activity of immobilized GL-7-ACA acylase treated with 4% (w/w) sodium cyanoborohydride remained almost 100% after 20 times of reuse.     

大尺寸SiO2大孔材料固定化漆酶

以表面固定Cu2+的改性大尺寸SiO2大孔材料作为载体,考察了时间、pH和给酶量对漆酶固定化效果的影响,并对固定化漆酶的活性和稳定性进行了研究。结果表明:5 h时吸附达到平衡,pH为4.5、漆酶与载体比例为5 mg·g-1时固定化效果最好,酶活回收率可达到100.4%;固定化漆酶的最适pH和最适温度较游离漆酶的均有升高且范围变宽,固定化后,漆酶的pH稳定性和热稳定性都得到显著提高;固定化漆酶的K m值略高于游离漆酶的;固定化漆酶具有良好的操作稳定性,与底物反应反复操作10批次后剩余酶活为72.7%。     

Identification of Antioxidant and Anti-α-amylase Components in Lotus (Nelumbo nucifera,Gaertn.) Seed Epicarp

Nano-sized Fe₃O₄ was synthesized by chemical co-precipitation and subsequently modified with 3-aminopropyltriethoxysilane (APTES) and glutaraldehyde to introduce aldehyde group on its surface. With the help of “interface activation” by adding sucrose esters-11 as surfactant, lipase from Rhizopus oryzae was successfully immobilized onto the carrier with great enhancement of activity. The hydrolysis activity of immobilized enzyme were 9.16 times and 31.6 times of free enzyme when p-nitrophenol butyrate and p-nitrophenol palmitate were used as substrates. The thermo-stability of immobilized enzyme was also enhanced compared to free enzyme. The immobilized enzyme was successfully applied in synthesis of 1,3-diacyglycerols (1,3-DAG). The specific esterification activity of immobilized enzyme was about 1.5 times of the free enzyme. The immobilized enzyme showed good region-selectivity towards 1,3-diacyglycerols and retained nearly 80% of its activity after reused for 60 times, revealing a good industrial application prospect.

     

氨基酸分子改性的SiO2杂化材料用于胰蛋白酶固定化

为改善二氧化硅载体材料本身的生物相容性和疏水性,维持包埋生物分子的活性,本文对水解前驱体3-氨基丙基三甲氧基硅烷进行氨基酸分子改性。具体过程包括N-Fmoc-L-缬氨酸和氯化亚砜反应生成N-Fmoc-L-缬氨酰氯,再和3-氨基丙基三甲氧基硅烷反应生成N-（3-三甲氧基硅基）丙基-N′-Fmoc-L-缬氨酰胺后。然后去除Fmoc,得到N-（3-三甲氧基硅基）丙基-L-缬氨酰胺作为氨基酸修饰的硅源前驱体。通过IR、MS、1H-NMR等分析测试手段对合成得到的各个化合物的结构进行了表征。利用正硅酸甲酯（TMOS）和N-（3-三甲氧基硅基）丙基-L-缬氨酰胺为复合硅源,经过溶胶-凝胶过程来包埋了胰蛋白酶,研究得到最适的固定化条件为,N-（3-三甲氧基硅基）丙基-L-缬氨酰胺的含量为15mol%。在该条件下,固定化胰蛋白酶活力的绝对值是199U,游离酶的酶活力的绝对值是103U, 四甲氧基硅烷直接包埋的固定化酶活力的活性是38 U。在该条件下,杂化硅源得到的固定化酶的活性是以四甲氧基硅烷水解前驱体的固定化酶活性的5倍,杂化硅源固定化胰蛋白酶的最相比游离酶,酶的最高活力提高的几乎2倍。这些结果表明氨基酸分子对水解前驱体修饰以后,水解产生的固定化载体具有良好的生物相容性。通过改性载体制备的固定化酶,对甲醇变性剂的稳定性,对酸碱的抵抗性及热稳定性也有明显地提高。     

The use of an immobilized enzyme nylon tube reactor incorporating a four enzyme system for creatinine analysis

A single immobilized enzyme nylon tube reactor was produced incorporating a four enzyme system for the analysis of creatinine. The enzyme activity ratios in the coupling solution used to prepare the reactor were found to be of extreme importance in governing the activity of the latter. The reactor was incorporated into a continuous flow analysis system used to assay creatinine in urine samples and the results were correlated with a manual technique employing the same enzyme system in solution. The precision, correlation, high specificity, simplicity, and speed of the analysis were concluded to be factors in favor of the method's suitability for urine creatinine determinations.     

脂肪酶的固定化及其在有机酶促反应中稳定性研究

利用吸附法,将圆柱状假丝酵母脂肪酶固定于４种疏水性不同的载体上,固定化酶的活性及稳定性随载休疏水性的增大而增大。用ＹＧＷ－Ｃ６Ｈ５作为载体,在有机溶剂－水双液相体系中催化萘普生甲酯的不对称水解,反应１２０ｈ转化率为２４．７２％,产品的对映体过量值为９４．８２％。     

Bioluminescent Flow Sensors: L-Alanine Determination in Serum and Urine

Abstract

A continuous flow bioluminescent method for L-alanine analysis in serum and urine has been developed. Serum can be analyzed directly after simple filtration. Response is linear from 50 to 1500 pmoles in biological matrix. Alanine dehydrogenase is immobilized onto a nylon coil separated from the reactor coil containing bioluminescent enzymes. The stability of nylon immobilized enzymes is high (over three months) and more than 900 samples can be analyzed with few mg of enzymes. The results obtained with the bioluminescent sensor agree well with those obtained by ion exchange chromatography (amino acid analyzer).