激波冲击下air/SF6界面的Richtmyer-Meshkov不稳定性

实验研究了低马赫数(1.27)激波作用air/SF6界面的RM不稳定性问题.air/SF6初始正弦界面由厚度为1～2 μm的薄膜相隔得到,用阴影法测试界面演化过程.实验结果表明:由于不稳定性重流体(SF6)向轻流体(air)演化成“尖钉”结构,而轻流体演化为“气泡”结构;由于界面切向速度差的Kelvin-Helm-ho...     

反射激波冲击重气柱的RM不稳定性数值研究

数值研究了二维气柱在入射激波以及反射激波作用下的Richtmyer-Meshkov(RM)不稳定性发展规律, 采用有限体积法结合网格自 适应技术的VAS2D程序, 精确刻画激波和界面的演化. 入射平面激波的马赫数为1.2, 气柱界面内气体为六氟化硫(SF₆), 环境气体为空气, 激波管的尾端为固壁. 通过改变气柱与尾端之间的距离调节反射激波再次作用已经变形的气柱的时间, 获得不同时刻下已经变形的气柱形态、界面尺寸以及环量演化受到反射激波的影响. 结果表明, 反射激波再次作用气柱时, 气柱所处发展阶段不同, 界面演化规律以及环量随时间的变化也不相同, 反射激波与气柱相互作用过程中的涡量产生和分布与无反射情况差异较大, 揭示了不同情况下界面演化的物理机理.     

柱形汇聚激波冲击球形重气体界面的实验研究

采用高速纹影法实验研究了柱形汇聚激波与球形重气体界面相互作用的 Richtmyer-Meshkov不稳定性问题. 激波管实验段基于激波动力学理论设计, 将马赫数为1.2 的平面激波转化为柱形汇聚激波, 气体界面由肥皂膜分隔六氟化硫(内)和空气(外)得到. 采用高速摄影机在单次实验中拍摄激波运动的全过程, 对柱形激波的形成进行了实验验证, 并进一步观测了汇聚激波与球形气体界面相互作用过程中的波系发展和气体界面变形以及反射激波同已变形界面二次作用的流场演化. 结果表明: 当柱形汇聚激波穿过气泡界面以后, 气泡左侧界面极点沿激波传播方向保持匀速运动, 气泡右侧界面发展成为射流结构, 气泡主体发展成为涡环结构; 在反射激波的二次作用下, 流场中无序运动显著增强并很快进入湍流混合阶段.     

激波诱导环形SF6气柱演化的机理

基于可压缩多组分Navier-Stokes控制方程,结合5阶加权本质无振荡格式以及网格自适应加密技术和level-set方法,数值模拟了平面激波(Ma=1.23)与环形SF₆气柱(内外半径分别为8和17.5 mm)界面的相互作用过程。相比于之前的实验结果,数值模拟结果揭示了入射激波在界面内4次透射过程中的复杂波系结构,观察到透射激波在内部界面传播时形成自由前导折射结构并向自由前导冯诺依曼折射结构转换的波系演变过程;另外,界面内的复杂激波结构诱导内部下游界面上的涡量发生了3次反向;在界面演化后期,内部界面形成的“射流”结构与下游界面相互作用,诱导界面形成一对主涡、一对次级涡以及一个反向“射流”结构。定量分析了环形界面长度、宽度、位移、环量以及混合率的变化情况,结果表明,内部气柱的存在减弱了前期小涡结构合并形成大涡结构过程中对界面高度与长度的影响,同时提高了重质气体与环境气体的混合率。     

磁场对激波冲击R22重气柱作用过程影响的数值模拟

为研究平面入射激波与磁化R22重质圆形气柱的作用过程,首先通过数值方法得到了不同初始条件下激波诱导R22气柱的Kelvin-Helmholtz (KH)及Richtmyer-Meshkov (RM)不稳定性导致的重气柱变形过程,并详细讨论了不同情况下透射激波在气柱内聚焦诱导射流的过程;然后在加入磁场的情况下,采用CTU+CT算法进行数值模拟,以保证数值结果满足任意时刻磁场的散度为零。计算结果表明:磁场对激波诱导R22气柱不稳定性具有抑制作用;法向磁场和流向磁场都可以很好地抑制RM不稳定性;对于KH不稳定性,法向磁场的控制效果更好,不仅可以抑制界面上涡串的卷起,还可以阻止主涡的发展,而流向磁场做不到后者;磁场对射流影响不大,射流处的磁能量可以一定程度上抑制射流的衰减,同时法向磁场可以减小聚焦时压力及速度峰值。     

反射激波作用下三维凹气柱界面演化的数值研究

激波与气柱相互作用是Richtmyer-Meshkov不稳定性研究的经典案例.单次激波与二维气柱相互作用已得到广泛关注,但是反射激波再次冲击气柱(尤其是三维气柱)的研究较少,相关演化规律和机理尚不清楚.反射激波再次冲击演化中的气柱界面会产生新的斜压涡量,影响涡量的输运和分布,从而影响界面的演化.本文采用自主开发的HOW...     

激波与椭圆形重气柱相互作用的PLIF实验

在水平激波管中,采用平面激光诱发荧光(planar laser-induced fluorescence, PLIF)方法对椭圆形重气柱界面的Richtmyer-Meshkov不稳定性进行实验。气柱由SF₆混入一定比例的丙酮蒸气构成,环境气体为空气。通过改变椭圆形气柱的长短轴比值,得到了激波马赫数为1.25时,3种初始界面的演化形态。通过相对体积分数标定,得到了界面失稳演化过程中的相对体积分数分布,观察到了激波作用后界面气体聚集、转移、消散等现象。实验结果发现,对于流向轴长与展向轴长之比较大的气柱界面,初始界面产生的涡量更大且分布更广,其界面不稳定性发展得越迅速和剧烈。失稳发展迅速的界面甚至出现涡对碰撞并产生尾部射流结构的现象。初始界面直接决定了失稳发展初期形成的涡对强度和间距,并对后期演化有重要影响。     

不同初始磁场对激波冲击R22重气柱过程影响的数值模拟

基于磁流体动力(magneto-hydrodynamic,MHD)方程,采用CTU+CT方法,对在不同初始磁场作用下的平面入射激波与磁化R22重质气柱作用过程进行了数值研究。数值结果清晰地描述了不同初始磁场条件时激波诱导R22气柱界面不稳定性的过程,揭示了磁场控制界面不稳定性的机理。另外,还分析了磁感应强度对界面不稳定性的影响,发现在磁场较小时,涡层附着于界面,但随着磁感应强度的增大,平均涡量随之增大,涡层与界面逐渐分离,最终更好地抑制了界面不稳定性。同时,还发现平均涡度拟能随着磁感应强度的增大而减小,而垂直磁场比平行磁场更能降低平均涡度拟能,因而平均涡度拟能可较好地反映磁场对不稳定性的影响效果。     

平面激波冲击并排液滴的三维数值模拟研究

采用三维守恒清晰界面数值方法, 研究平面激波冲击并排液滴的动力学过程. 研究的焦点在于激波接触液滴后的复杂波系结构生成, 以及并排液滴相互耦合作用诱导的单个液滴非对称界面演化. 首先, 分析并排液滴之间界面通道内的波系结构发展, 发现在冲击初期由于反射激波相交而形成新的反射激波以及马赫杆; 这些流动现象与液滴另外一侧 (非通道侧) 由激波反射所形成的弯曲波阵面截然不同, 而且所导致的液滴横向两侧流场差异是中后期冲击过程液滴两侧界面非对称演化的主要原因. 其次, 研究冲击中期时, 特别是入射激波已运动至液滴下游并远离并排液滴, 界面形态的演化过程和规律, 揭示通道下游出口处由于气流膨胀导致的界面闭合、以及随后气流阻塞导致的界面破碎等新的流动现象. 最后, 研究液滴间距对并排液滴相互作用的影响规律, 发现液滴间距大小与通道内压力峰值具有明显的关联关系. 研究表明, 更小的液滴间距不仅带来更大的压力峰值, 而且使得峰值出现的时间更早.      

激波和湍流相互作用的数值模拟

本文综述了关于激波和湍流相互作用数值模拟的近期研究进展, 主要包括激波和均匀各向同性湍流、激波和湍流边界层、激波和射流以及激波和尾迹的相互作用. 激波和湍流相互作用特性受到诸多因素的影响,如激波的强度、位置、形状和流动边界以及来流的湍流状态和可压缩性等. 激波和湍流的相互作用会引起流场结构、激波特性和湍流统计特性的显著变化. 最后简要讨论了激波和湍流相互作用数值研究需要关注的一些问题.      

Effect of air jet vortex generators on a shock wave boundary layer interaction

The effect of upstream injection by means of continuous air jet vortex generators (AJVGs) on a shock wave turbulent boundary layer interaction is experimentally investigated. The baseline interaction is of the impinging type, with a flow deflection angle of 9.5° and a Mach number M _e  = 2.3. Considered are the effects of the AJVGs on the upstream boundary layer flow topology and on the spatial and dynamical characteristics of the interaction. To this aim, Stereoscopic Particle Image Velocimetry has been employed, in addition to hot-wire anemometry (HWA) for the investigation of the unsteady characteristics of the reflected shock. The AJVGs cause a reduction of the separation bubble length and height. In addition, the energetic frequency range of the reflected shock is increased by approximately 50%, which is in qualitative agreement with the smaller separation bubble size.     

基于气泡形态影响的水下气幕对冲击波衰减效果分析

气泡帷幕是水下爆炸冲击波防护的重要手段,对其作用机理及技术参数的深入研究对水下爆破安全与应用具有重要意义。采用高速摄影技术对室内小型水下气泡帷幕模型拍摄发现气幕在形成过程和与水下爆炸冲击波相互作用过程中均具有高度非连续性和非均匀性,且气幕区域内气体与液体混杂,界面轮廓复杂多样。在此基础上,考虑气泡形状及界面影响下,通过LS-DYNA有限元软件自带的APDL语言进行编程,实现了在设定的气幕区域内,通过设定气泡直径变化范围及气泡直径之间的最小差异值随机投放一定数量不同直径的气泡来模拟真实气幕中气泡的分布,并通过改变固定区域内气泡个数来模拟不同气压值工况下的气幕效果。分析发现该方法能够更加真实反映气幕在冲击波防护过程中的防护机理,随着单位区域内气泡数量的增大,防护效果越明显,但当气泡数量达到一定数量后气幕整体连续性及稳定性基本固定,防护效果也趋于稳定。     

Dependence between the shock and the separation bubble in a shock wave boundary layer interaction

We present experimental results obtained in a turbulent boundary layer at a Mach number of 2.3 impinged by an oblique shock wave. Strong unsteadiness is developed in the interaction, involving several frequency ranges which can extend over two orders of magnitude. In this paper, attention is focused on the links between the low-frequency shock motions and the separation bubble, in particular phase relationships are evaluated. An interpretation based on a simple scheme of the streamwise evolution of the instantaneous pressure is proposed. As it is mainly based on the pressure signal properties inside the region of the shock oscillation, it may be expected that it will still be relevant for different configurations of shock-induced separation as compression ramp, blunt bodies, or over expanded nozzles.     

Experimental and numerical investigation of inclined air/SF6 interface instability under shock wave

The shock tube experiments of inclined air/SF6 interface instability under the shock wave with the Mach numbers 1.23 and 1.41 are conducted. The numerical simulation is done with the parallel algorithm and the multi-viscous-fluid and turbulence (MVFT) code of the large-eddy simulation (LES). The developing process of the interface accelerated by the shock wave is reproduced by the simulations. The complex wave structures, e.g., the propagation, refraction, and reflection of the shock wave, are clearly revealed in the flows. The simulated evolving images of the interface are consistent with the experimental ones. The simulated width of the turbulent mixing zone (TMZ) and the displacements of the bubble and the spike also agree well with the experimental data. Also, the reliability and effectiveness of the MVFT in simulating the problem of interface instability are validated. The more energies are injected into the TMZ when the shock wave has a larger Mach number. Therefore, the perturbed interface develops faster.     

Vortex flows induced by interaction of a shock wave with thin regions of finite length and reduced density

A theoretical and experimental investigation has been made of the dynamics of the vortex flow induced by thin regions of reduced density in precursors that develop ahead of shock fronts during the propagation of shock waves through a channel and after its end up to the stage of restoration of the undisturbed flow. The satisfactory agreement between the experimental and calculated data indicates that the numerical analysis of the process in the framework of the Euler equations is valid.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 149–153, May–June, 1993.     

Air shock wave interaction with an obstacle covered by porous material

The interaction between an air shock wave and a rigid wall covered by a porous screen is investigated numerically and experimentally. A mathematical two velocity with two stress tensors model is used for studying the wave processes in saturated porous media. The process of reflection of a step-type wave from a rigid wall covered with a porous layer is considered, the effect of the porous medium and wave parameters on the reflection is analyzed, and the numerical results are compared with the experimental data.Received: 30 July 2002, Accepted: 24 December 2002, Published online: 27 May 2003     

可燃气体中激波与障碍物作用在下游形成爆轰波的数值研究

对平面激波和单个矩形障碍物作用的过程进行了数值模拟,研究了反射产生的上行爆轰波在下游可燃气体中形成爆轰波的过程。数值结果表明,下游爆轰波形成过程主要有2种模式:爆轰波直接绕射和绕射波在上壁面反射,这和已有的实验结果是一致的。通过研究下游爆轰波的形成过程受入射激波马赫数、混合气体的压力和管道尺度的影响,分析了上游爆轰波向下游传播的波动力学过程,讨论了2种形成过程的作用规律和控制因素,阐明了下游爆轰波的形成规律。     

Computational study of planar shock wave interacting with elliptical heavy gas bubble

Acta Mechanica Sinica - High-precision numerical methods are utilized to study the shock waves interacting with an elliptical heavy bubble. The influence of different bubble gases (SF $$_6$$ and...     

Numerical investigation of ethylene flame bubble instability induced by shock waves

In this paper, the ethylene/oxygen/nitrogen premixed flame instabilities induced by incident and reflected shock wave were investigated numerically. The effects of grid resolutions and chemical mechanisms on the flame bubble deformation process are evaluated. In the computational frame, the 2D multi-component Navier–Stokes equations with second-order flux-difference splitting scheme were used; the stiff chemical source term was integrated using an implicit ordinary differential equations (ODEs) solver. The two ethylene/oxygen/nitrogen chemical mechanisms, namely 3-step reduced mechanism and 35-step elementary skeletal mechanism, were used to examine the reliability of chemistry. On the other hand, the different grid sizes, Δx × Δy = 0.25 × 0.5mm and Δx × Δy = 0.15 × 0.2mm, were implemented to examine the accuracy of the grid resolution. The computational results were qualitatively validated with experimental results of Thomas et al. (Combust Theory Model 5:573–594, 2001). Two chemical mechanisms and two grid resolutions used in present study can qualitatively reproduce the ethylene spherical flame instability process generated by an incident shock wave of Mach number 1.7. For the case of interaction between the flame and reflected shock waves, the 35-steps mechanism qualitatively predicts the physical process and is somewhat independent on the grid resolutions, while the 3-steps mechanism fails to reproduce the instability of ethylene flame for the two selected grid resolutions. It is concluded that the detailed chemical mechanism, which includes the chain elementary reactions of fuel combustion, describes the flame instability induced by shock wave, in spite of the fact that the flame thickness (reaction zone) is represented by 1–2 grids only.      

FLAT-PLATE BOUNDARY-LAYER FLOWS INDUCED BY DUSTY SHOCK WAVE

ＦＬＡＴ－ＰＬＡＴＥＢＯＵＮＤＡＲＹ－ＬＡＹＥＲＦＬＯＷＳＩＮＤＵＣＥＤＢＹＤＵＳＴＹＳＨＯＣＫＷＡＶＥ（王柏懿）（陶锋）ＦＬＡＴ－ＰＬＡＴＥＢＯＵＮＤＡＲＹ－ＬＡＹＥＲＦＬＯＷＳＩＮＤＵＣＥＤＢＹＤＵＳＴＹＳＨＯＣＫＷＡＶＥ￥ＷａｎｇＢｏｙｉ；Ｔａ...