Laboratory and field measurements of a badge type passive sampler for the determination of ambient sulfur dioxide concentrations

The performance of a badge type passive sampler for the determination of sulfur dioxide is described. The trapping agent is triethanolamine. Analysis is performed by ion chromatography. Thus, the method allows the simultaneous detection of sulfur dioxide and nitrogen dioxide. The sampler was tested in the laboratory and in the field. The intercomparison with independent methods in the field showed very good agreement against two active sampling methods. Regression analyses (the results of the passive sampler always represent the y-axes) gave r² = 0.81 and k = 1.07 ± 0.01 for the intercomparison with an annular denuder technique and r² = 0.92 and k = 0.96 ± 0.01 for the intercomparison with a commercial fluorescence sulfur dioxide analyzer. The average reproducibility in the field was 7% (RSD). The detection limit was 0.18 μg SO₂/m³ for an exposure time of two weeks. Received: 9 February 1998 / Revised: 22 June 1998 / Accepted: 26 June 1998     

新型二氧化硫被动采样器的研制

研究了一种新型二氧化硫被动采样器。考察了无纺布、定性滤纸和定量滤纸等吸收剂的载体在相同情况下对二氧化硫和二氧化氮的吸收效果 ,对吸收载体进行了优选。并针对低温地区和高温高湿的气候条件 ,确立了以三乙醇胺(TEA)为吸收主体 ,分别以乙二醇、丙三醇为添加剂的吸收体系。     

“Badge-type” passive sampler for monitoring ambient ammonia concentrations

A passive “badge-type” sampling device for the determination of gaseous ammonia was developed. The collection substrate is phosphoric acid. The sampler can be used for outdoor and indoor sampling of ammonia in the concentration range from 0.05 μg/m³ to 10 mg/m³. The performance was tested in the laboratory and in the field against an annualar denuder, a filter pack and an impinger technique. The intercalibration showed that the passive sampler compares very well with active samplers (r²=0.99; k=1.05). The average reproducibility of the sampler was 8%. Hence the badge sampler is well suited for the determination of ammonia in a wide range of concentrations and particularly for application under rural background conditions. The sampling rate of the device was calculated according to a simple multi-layer model.     

Validation of the Willems badge diffusive sampler for nitrogen dioxide determinations in occupational environments

The Willems badge, a diffusive sampler for nitrogen dioxide, has previously been validated for ambient air measurements. This paper describes the laboratory and field validation of the Willems badge for personal sampling under working environment conditions. The mean sampling rate in the laboratory tests was 46 ml min(-1), with an RSD of 12%. No statistically significant effects on sampling rate of the sampling time, concentration of NO2 or relative humidity were found. A slightly decreased sampling rate was observed at low wind velocity. This was also confirmed during static sampling, which makes the sampler less appropriate for static sampling indoors. No back diffusion was observed. Storage of the samplers for two weeks before or after exposure did not affect the sampling rate. Our analysis is based on a modified colorimetric method, performed by FIA (flow injection analysis). This technique was compared to ion chromatography analysis. The use of ion chromatography lowered the detection limit from 11 to 2 microg m(-3) for an 8 h sample, and furthermore enabled the detection of other anions. In conclusion, the diffusive sampler was found to perform well for personal measurements in industrial environments.     

Laboratory development and field evaluation of a new diffusive sampler to collect nitrogen oxides in the ambient air

Diffusive samplers for the determination of NO(x) and NO2 based on collection on a coated carbon paper filter have been developed. NO is first oxidized to NO2 and then collected on the reactive surface. When NO2 and NOx samplers are exposed simultaneously, NO can be calculated by difference. The sampler has been derived from a Palmes design as recently modified by Bertoni et al. for the determination of BTX (benzene, toluene, xylenes). Laboratory tests were conducted in controlled atmosphere to evaluate linearity, uptake rate, face velocity effects, sample stability, influence of relative humidity, precision and accuracy. The samplers are capable of reliable measurements of the two species at common levels of a polluted atmosphere in urban settings yielding average concentration levels over 1 month and beyond.The uptake rate of NO2 was found to be 11.7 mL/min in a very good agreement (within 5%) with the value calculated from theory. The measured uptake rate for NO(x) was determined in experiments involving sampling at different concentration levels in comparison to chemiluminescence (CL) measurements. The precision of the measurements for co-located passive samplers was better than 5%. The accuracy of the data collected is within +/-20% of the actual value measured by CL. The laboratory and field results show that the NO(x) and NO2 samplers meet the data quality goal requested by the first EU Directive 1999/30/EU for these pollutants.     

Development and field evaluation of a new diffusive sampler for Hydrogen Sulphide in the ambient air

A diffusive sampler for the determination of hydrogen sulphide (H₂S) based on collection on a paper filter coated with silver nitrate followed by optical densitometric determination of the metal sulphide was developed. Laboratory tests were conducted in controlled atmosphere to evaluate linearity, uptake rate, face velocity effects, sample stability, influence of relative humidity and of interferents, precision and accuracy. The measured uptake rate for H₂S was determined in experiments involving sampling at different concentration levels in comparison to a wet standard colorimetric technique. The precision of the measurements for co-located passive samplers was lower than 15%. The accuracy of the data collected is within 20% of the actual value measured by the wet method. The sampler is capable of reliable measurements of H₂S at common levels of a polluted atmosphere in urban settings yielding average concentration levels over one month and beyond. Diffusive sampling can be adopted to analyse in detail the temporal and spatial trends of H₂S concentration in ambient air and in specific historic buildings or in museums. Figure At the end of sampling cap #2 is removed and optical density is measured     

Modification of Amaya-Sugiura passive sampling spectrophotometric method of nitrogen dioxide determination in ambient air

Summary On the example of the previously tested method of nitrogen dioxide determination in ambient air two aspects of wind influence on the badge-type sampler performance were discussed: an appropriate design of the sampler eliminating any open recess over the face of the sampler and so called starvation effect i.e. decrease in the mass of analyte absorbed by the sampler at wind velocities below 20 cm/s. The wind effect on the performance of the passive sampler has been diminished from about 150% to maximum 20%.     

Evaluation of a passive sampler for airborne formaldehyde

Summary A diffusive sampler for the large scale routine determination of airborne formaldehyde was developed. Formaldehyde is sampled in a badge-type passive sampler containing a 2,4-dinitrophenylhydrazine-coated filter paper as sampling layer. Formaldehyde is immediately converted to the corresponding hydrazone, which, after desorption with acetonitrile, is separated and quantified by gradient HPLC using UV detection at 345 nm. Calibration was done via an active sampling method and showed an excellent, time- and concentration-independent linear performance of the diffusive samplers. A detection limit of about 0.05 ml/m³·h (ppm·h) and a relative standard deviation of about 10% ensured a good analytical reliability. By testing the influence of air movements at the sampler surface, a minimum air velocity of 10 cm/s was found necessary to ensure representative sampling.     

Construction and performance of a drop cell for the nephelometric determination of sulfur dioxide

A nephelometric technique based on a liquid drop is described for the measurement of atmospheric sulfur dioxide. A 40-μl drop of barium chloride and hydrogen peroxide solution is suspended in a flowing-air sampling stream. The sulfur (IV) collected is oxidized to sulfur (VI) and finally precipitated as barium sulfate. Nephelometric detection of drop is achieved by an appropriate arrangement consisting of an optical fiber contacting the drop and a photodiode placed at 90° relative to the fiber. The design and characteristics of this drop-based gas sensor system are described. The analytical response, as photocurrent, is proportional to the product of the sampling period and the sulfur dioxide concentration. The detection limit is ca. 1.1 mg m⁻³ for a 10-min sampling time. The present technique is fairly rapid and simple, uses a small amount of reagent and is set up with low-cost equipment, making this system economically viable.     

Ultra-high performance liquid chromatographic method for the determination of polycyclic aromatic hydrocarbons in a passive environmental sampler

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous compounds released in the environment by different sources. The aim of the present work was to validate a solid‐phase extraction (SPE) and a rapid ultra‐high performance liquid chromatographic (UHPLC) method for the analysis of PAHs in a passive environmental sampler, namely a Dacron® (the commercial name of a synthetic fiber based on polyethylene terephthalate) textile. The elution temperature was optimized to improve the resolution of early‐eluted compounds, namely acenaphthene (Ac) and fluorene (F). The UHPLC method lasts about 10 min and showed good linearity for all the 16 PAHs considered, with regression coefficients over 0.99. Recoveries, limits of detection (LODs), and limits of quantification (LOQs) of the SPE method were well within the performance criteria fixed by the Regulation n. 836/2011, namely 0.3 and 0.9 μg/kg, respectively.     

Simple spectrophotometric and titrimetric methods for the determination of sulfur dioxide.

The proposed work describes a simple spectrophotmetric as well as a titrimetric method to determine sulfur dioxide. The spectrophotometric method is based on a redox reaction between sulfur dioxide and iodine monochloride obtained from iodine with chloramine-T in acetic acid. The reagent iodine monochloride oxidizes sulfur dioxide to sulfate, thereby reducing itself to iodine. Thus liberated iodine will also oxidize sulfur dioxide and reduce itself to iodide. The obtained iodide is expected to combine with iodine to form a brown-colored homoatomictriiodide anion (460 nm), which forms an ion-pair with the sulfonamide cation, providing exceptional color stability to the system under an acidic condition, and is quantitatively relatd to sulfur dioxide. The system obeys Beer's law in the range 5 - 100 microg of sulfur dioxide in a final volume of 10 ml. The molar absorptivity is 5.03 x 10(3) l mol(-1)cm(-1), with a relative standard deviation of 3.2% for 50 microg of sulfur dioxide (n = 10). In the titrimetric method, the reagent iodine monochloride was reduced with potassium iodide (10%) to iodine, which oxidized sulfur dioxide to sulfate, and excess iodine was determined with a thiosulfate solution. The volume difference of thiosulfate with the reagent and with the sulfur dioxide determined the sulfur dioxide. Reproducible and accurate results were obtained in the range of 0.1 - 1.5 mg of sulfur dioxide with a relative standard deviation of 1.2% for 0.8 mg of sulfur dioxide (n = 10).     

Evaluation of the novel passive sampler for cyanobacterial toxins microcystins under various conditions including field sampling

In the present study, we have evaluated the effectiveness of a passive sampler for polar organic chemicals to accumulate a group of widespread and hazardous tumor-promoting toxins produced in cyanobacterial water blooms—microcystins (MC). The previously optimized configuration of the sampler based on polycarbonate membrane and Oasis HLB sorbent (2.75 mg/cm²) was validated under various exposure scenarios in laboratory and field. Calibration of the passive sampler conducted under variable conditions and concentrations of MC revealed linearity of the sampling up to 4 weeks. The sampling rates of microcystins for two different exposure scenarios were derived (e.g., MC-LR: R _s = 0.017 L/day under static and 0.087 L/d under turbulent conditions). R _s values were further used for calculations of time-weighted average concentrations in natural water. Improved sensitivity and selectivity of the in-house-made sampler was observed in comparison with the commercially available Polar Organic Compound Integrative Sampler (POCIS). Comparisons of grab and passive sampling methods were performed during cyanobacterial water bloom season in the Brno reservoir, Czech Republic in 2008. Data obtained by passive sampling provided a more relevant picture of the situation and enabled better assessment of potential risks. The present study demonstrated that the modification of POCIS is suitable for monitoring of occurrence and retrospective estimations of microcystin water concentrations, especially with respect to the control of drinking water quality.     

Membrane assisted passive sampler for triazine compounds in water bodies--characterization of environmental conditions and field performance

This article reports the integration of the fiber optic-particle plasmon resonance (FO-PPR) biosensor with a microfluidic chip to reduce response time and improve detection limit. The microfluidic chip made of poly(methyl methacrylate) had a flow-channel of dimensions 4.0 cm × 900 μm × 900 μm. A partially unclad optical fiber with gold or silver nanoparticles on the core surface was placed within the flow-channel, where the volume of the flow space was about 14 μL. Results using sucrose solutions of various refractive indexes show that the refractive index resolution improves by 2.4-fold in the microfluidic system. The microfluidic chip is capable of delivering a precise amount of biological samples to the detection area without sample dilution. Several receptor/analyte pairs were chosen to examine the biosensing capability of the integrated platform: biotin/streptavidin, biotin/anti-biotin, DNP/anti-DNP, OVA/anti-OVA, and anti-MMP-3/MMP-3. Results show that the response time to achieve equilibrium can be shortened from several thousand seconds in a conventional liquid cell to several hundred seconds in a microfluidic flow-cell. In addition, the detection limit also improves by about one order of magnitude. Furthermore, the normalization by using the relative change of transmission response as the sensor output alleviate the demand on precise optical alignment, resulting in reasonably good chip-to-chip measurement reproducibility.     

Evaluation of a passive air sampler for measuring indoor formaldehyde.

A passive air sampler, using 4-amino-3-hydrazino-5-mercapto-1,2,4-triazole, was evaluated for the determination of formaldehyde in indoor environments. Chromatography paper cleaned using a 3% hydrogen peroxide solution was experimentally determined as being the optimum absorption filter for the collection of formaldehyde (0.05 microg cm(-2) formaldehyde). From a linear-regression analysis between the mass of formaldehyde time-collected on a passive air sampler and the formaldehyde concentration measured by an active sampler, the sampling rate of the passive air sampler was 1.52 L h(-1). The sampling rate, determined for the passive air sampler in relation to the temperature (19 - 28 degrees C) and the relative humidity (30 - 90%), were 1.56 +/- 0.04 and 1.58 +/- 0.07 L h(-1), respectively. The relationship between the sampling rate and the air velocity was a linear-regression within the observed range. In the case of exposed samplers, the stability of the collected formaldehyde decreased with increasing storage time (decrease of ca. 25% after 22 days); but with the unexposed samplers the stability of the blank remained relatively unchanged for 7 days (decrease of ca. 37% after 22 days). The detection limits for the passive air sampler with an exposure time of 1 day and 7 days were 10.4 and 1.48 microg m(-3), respectively.     

Selection of the type of methane conversion for catalytic reduction of sulfur dioxide

Catalytic reduction of sulfur dioxide with converted gas obtained by various methods of conversion of natural gas was studied to select the most active reducing agent for SO₂.     

Laboratory and field validations of a solid-phase microextraction device for the determination of ethylene oxide

Laboratory and field evaluations were performed to validate a solid-phase microextraction (SPME) device that was used as a diffusive sampler. Hydrogen bromide (HBr) was loaded onto the carboxen-polydimethylsiloxane (CAR-PDMS) fiber for the determination of ethylene oxide (EtO) with on-fiber derivatization. For laboratory evaluations, known concentrations of ethylene oxide around the threshold limit values (TLV)/time-weighted average and specific relative humidities (RHs) were generated by syringe pumps in a dynamic generation system. The SPME diffusive samplers and the commercially available 3M 3551 passive monitors were placed side-by-side in an exposure chamber which was designed to allow measurement of face velocities, temperatures, exposing vapor concentrations, and RHs. Field validations with both SPME diffusive sampler and 3M 3551 passive monitors were also performed. The correlations between the results from both SPME device and 3M 3551 passive monitor were found to be linear (r > 0.9699) and consistent (slope approximately equal to 1.12 +/- 0.07). However, the variations of diffusion coefficients at different temperatures needs to be considered and the adjustment of sampling constant was a must when sampling at temperatures different from 25 degrees C.     

On-line pervaporation-capillary electrophoresis for the determination of volatile acidity and free sulfur dioxide in wines

Pervaporation has been coupled on-line to capillary electrophoresis (CE) by a simple interface consisting of a modified CE vial. The approach allows volatile analytes to be removed and injected into the capillary meanwhile the sample matrix remains in the pervaporator. By this approach volatile acidity and free sulfur dioxide have been simultaneously determined in wines. The detection limits (LODs) are 1.25 and 5.00 microg/mL, the quantification limits 4.12 and 16.50 microg/mL, and the linear dynamic ranges between LOD and 50 microg/mL and between 0.1 and 0.9 g/L for free sulfur dioxide and volatile acidity, respectively. The repeatability and within laboratory reproducibility, expressed as relative standard deviation (RSD), are 1.61% and 3.00% for free sulfur, and 3.35% and 4.58% for volatile acidity, respectively. The optimal pervaporation time and the time necessary for the individual separation-detection of the target analytes are 6 and 5 min, respectively. The analysis frequency is 7 h(-1) and the sample amount necessary is less than 7 mL. The proposed method and official methods for the analytes were applied to 32 wine samples. A two-tailed t-test was used to compare the methods, which yielded similar results. The errors, expressed as RSD for the two parameters, ranged between 1.3 and 4.1%.     

A simple diffuse reflectance Fourier transform infrared spectroscopic determination of sulfur dioxide in ambient air using potassium tetrachloromercurate as the absorbing reagent

This paper presents development of a simple, rapid, and precise analytical method for determination of sulfur dioxide in ambient air by a gas to solid-phase conversion method. Sulfur dioxide is determined in the form of sulfite (SO3(2-)) because the absorbing reagent, potassium tetrachloromercurate (TCM), used in this method absorbs sulfur dioxide from the atmosphere in the form of sulfite. Determination of submicrogram levels of sulfur dioxide was based on the selection of a quantitative analytical peak at 495 cm(-1) among the 3 observed vibrational peaks for the dichlorosulfitomercurate complex formed after reaction of sulfur dioxide with TCM and measurement of absorbance using diffuse reflectance Fourier transform infrared spectroscopy. The limits of detection and quantification of the method were found to be 0.09 and 0.4 microg/g SO3(2-), respectively. The precision in terms of standard deviation and relative standard deviation (RSD) at a level of 2 microg SO3(2-)/10.1 g KBr for n = 10 was found to be 0.036 microg SO3(2-) and 1.8%, respectively. The RSD (n = 10) for determination of sulfur dioxide in ambient air was observed to be in the range of 2.7-4.2%. The method proposed is time saving and eliminates the slow and cumbersome steps of pH maintenance of the reaction mixture and color formation of the U.S. Environmental Protection Agency recommended West and Gaeke spectrophotometric method and other methods for quantitative determination of sulfur dioxide.     

Novel multi-sorbent for sampling and determination of trace volatile organic sulfur compounds in ambient air

Novel adsorbent APSG-MW (average particle size 215?µm and specific surface 98 m²?g^?1) bonding multi-walled carbon nanotubes (MWCNTs) on silica gel are obtained. Then the sampling tubes filled with Tenax TA and APSG-MW are prepared and the adsorptive capacity of Tenax TA/APSG-MW for volatile organic sulfur compounds (VOSCs) is studied. The data show that the adsorption and desorption recoveries of multi-sorbent for VOSCs are satisfactory (>85%), and the breakthrough values are large (>16?L?g^?1) enough to absorb VOSCs in ambient air. The sampling precision of the sorbent tubes meets TO-17 criteria. The sampling tubes are successfully used to concentrate and analyze a sample of landfill air, and the major S compounds are identified.     

Simple spectrophotometry method for the determination of sulfur dioxide in an alcohol-thionyl chloride reaction

Thionyl chloride is often used to convert alcohols into more reactive alkyl chloride, which can be easily converted to many compounds that are not possible from alcohols directly. One important reaction of alkyl chloride is nucleophilic substitution, which is typically conducted under basic conditions. Sulfur dioxide, the by-product from alcohol-thionyl chloride reactions, often reacts with alkyl chloride to form a sulfonyl acid impurity, resulting in yield loss. Therefore, the alkyl chloride is typically isolated to remove the by-products including sulfur dioxide. However, in our laboratory, the alkyl chloride formed from alcohol and thionyl chloride was found to be a potential mutagenic impurity, and isolation of this compound would require extensive safety measures. As a result, a flow-through process was developed, and the sulfur dioxide was purged using a combination of vacuum degassing and nitrogen gas sweeping. An analytical method that can quickly and accurately quantitate residual levels of sulfur dioxide in the reaction mixture is desired for in-process monitoring. We report here a simple ultraviolet (UV) spectrophotometry method for this measurement.