Fiber needle felt–silica aerogel composite was successfully prepared by via sol–gel process based on water glass. The thermal conductivity show V-type variation tendency with the increase of water to Si. Thermogravimetric analysis-differential scanning calorimetry analysis revealed that the thermal stability was up to approximately 390.58?°C. It has been found that the fire hazard of the composites decreased with the increased ratio of water to Si according to the cone calorimeter test, which can be characterized by peak heat release rate, fire performance index, and fire growth rate index. The fiber needle felt/aerogels present greatly improved compressive and flexural strength (elastic modulus: 0.1–0.97?MPa; flexural modulus: 0.33–0.66?MPa) while keeping inherent properties of pure silica aerogel: low bulk density (0.166?g/cm3), low thermal conductivity of 0.0236?W/m·K, and high specific surface area (1091.62?m2/g). As a result, the as-prepared composite shows a great potential to be applied in the thermal insulation field.
Two series of TiO2 thin films were prepared based on soluble precursor powders: The first run originated directly from an alcohol-based coating solution whereas for the second batch the aqueous precursor powder sol had previously undergone a hydrothermal treatment. The respective microstructures were characterized by electron microscopy, the phase evolution was monitored by X-ray diffraction. Ellipsometric porosimetry (EP) was employed to reveal changes of porosity and pore size induced by thermal treatment of the films.
Soluble TiO2 precursor powders were hydrothermally treated to yield coating solutions. Films from these sols were compared with those directly obtained by dissolving the precursor powders. Results indicate that crystallization to anatase is induced under hydrothermal conditions and the resulting films mostly maintain their porosity throughout thermal treatment. In contrast to that coatings processed from as-dissolved precursor powders undergo more extensive densification
A novel ZrCO composite aerogel is synthesized using zirconium oxychloride and resorcinol–formaldehyde (RF) as precursors through the sol–gel route and carbothermal reduction process. The effects of different Zr/R molar ratios and calcination temperatures on the physical chemistry properties of ZrCO aerogels are investigated. The ZrCO composite aerogel consists of the C/ZrO2/ZrC ternary aerogel. The results show that with the increase of R/Zr molar ratios, the specific surface area and bulk density increase with calcination temperature up to 1300?°C, but decrease at even temperature (1500?°C). The specific surface area is as high as 637.4?m2/g for ZrCO composite aerogel (R:Zr?=?2:1), which was higher than ever reported. As the heat-treatment temperature increases to 1500?°C, the ZrC crystalline phase occurs and the t-ZrO2 phase still appears within the composite. The thermal conductivity of the carbon fiber mat-reinforced composite aerogel is as low as 0.057?W/m/K at room temperature (25?°C).
Bismuth ferrite (BiFeO3) nanopowder have been successfully synthesized for the first time via a microwave-assisted sol-gel combustion method by using citric acid as fuel. The resulting nanopowder was characterized using FT-IR, TG-DTA, XRD, EDX, VSM, SEM, and UV-Vis DRS. A ferromagnetic hysteresis loop with a saturation magnetization (MS) of 0.66?emu?g?1 has been observed at room temperature in the sample. The optical properties of the nanosized BiFeO3 showed its small band gap (=2.08?eV) indicates a possibility of utilizing much visible light for photocatalysis.
The aim of this work was an investigation of structural and electrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) powders. The compounds obtained by sol-gel method are characterized by several techniques: X-ray diffraction (XRD), N2 adsorption–desorption isotherms, scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), electrical and dielectrical measurements. The XRD, SEM and XPS analysis confirmed the formation of ZnFeTiO4 inverse spinel structure. The electrical and dielectrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) were measured by impedance spectroscopy, revealing a decrease in the electrical conductivity and the dielectric constant with Fe content.
In this study, the effective TiO2/Ag composite antibacterial aerogel powder is prepared by facile sol–gel method and ethanol supercritical technology. The surface morphology, structural properties, and chemical components are monitored by scanning electron microscopy (SEM), transmission electron microscope (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and energy disperse?spectroscopy (EDS). Meanwhile, absorbance spectra and specific surface area of TiO2/Ag composite aerogel are characterized by UV-Vis spectra and Brunauer–Emmett–Teller. The TiO2/Ag composite aerogel with Ti/Ag molar ratios of 10:1, 30:1, 50:1 are measured for its antibacterial property by using Escherichia coliform (E.coli) and Staphylococcus aureus (S. aureus). The results show that the size of TiO2 and Ag nanoparticles are 40?nm and 25?nm, respectively. Simultaneously, the obtained composite aerogel with a porous structure possessed a surface area of 148?m2/g, an average pore size 11.5?nm, and a pore volume 0.39?cm3/g. With the increase of Ag content, the antibacterial properties of composite aerogel are greatly improved compared with pure TiO2 aerogel. When Ag/Ti molar ratios was 1:10, the highest antibacterial rate can up to 99%, and the inhibition bands of E. coli and S. aureus are 23?mm and 19?mm, respectively.
MgF2 coating solutions were solvothermally treated at 160?°C for different time periods, this procedure induced crystallization and particle growth. Antireflection coatings prepared on glass from these solutions were compared to films derived from untreated precursor material. Ellipsometric porosimetry (EP) was employed to characterize structural features of coatings on glass as function of annealing temperature. Based on precursor solutions that had undergone solvothermal treatment antireflective coatings with a peak transparency exceeding 99% were prepared on PMMA substrates.
Solvothermal treatment of MgF2 precursor solutions results in crystallization of particles that can directly be applied to PMMA substrates for λ/4 antireflective films.
Novel La-doped Bi2WO6 composites were successfully prepared via a facile solvothermal method and well characterized by X-ray diffraction, Brunner?Emmet?Teller measurements, scanning electron microscopy, transmission electron microscopy/high-resolution, energy dispersive spectrometry, X-ray photoelectron spectroscopy, ultraviolet–visible spectroscopy, and Fourier transform infrared spectroscopy. The photocatalytic activity of modified catalysts was evaluated by degrading tetracycline hydrochloride under visible light (450?W Xe lamp irradiation). It was found 5%La-Bi2WO6 had the highest light-absorption ability, great morphology, and microstructures. The La dopant enlarged surface area and increased crystal defects, which may enhance the optical absorption activity and inhibit the recombination of the photo-generated charge carrier, respectively. After 150?min illumination, the photocatalysts that 5%La-Bi2WO6 and pure Bi2WO6 exhibited the best and worst photocatalytic performance, respectively (96.25% vs. 88.92%).
Since the late 1960s, ceric hydrogen phosphates have attracted the attention of scientists due to remarkable ion exchange, sorption, proton-conduction and catalytic properties. In this work, through the application of various solvents, we, for the first time, have obtained monolithic aerogels based on ceric hydrogen phosphates with high porosity (~99%) and extremely low density (~10?μg/cm3). The composition and structure of aerogels were thoroughly studied with XRD, TEM, SEM, XPS, low temperature nitrogen adsorption methods, TGA/DSC, Fourier-transform infrared spectroscopy (FTIR) and small-angle neutron scattering (SANS). The aerogels were found to belong to the fibrous macroporous aerogels family.
A facile procedure was developed for the production of Al2O3 aerogels modified with tris(8-hydroxyquinolinato)aluminum complex (AlQ3). The addition of 8-hydroxyquinoline during the stage of alumina lyogel formation was found to increase gelation duration. The translucent monolithic aerogels were obtained by supercritical drying of lyogels in CO2. The composition and properties of aerogels were analyzed using low-temperature nitrogen adsorption, helium pycnometry, IR spectroscopy, UV–visible spectroscopy, luminescence spectroscopy, powder X-ray diffraction, scanning and transmission electron microscopy, and thermogravimetry combined with mass spectrometry. The obtained aerogels had low density (0.15–0.18?g?cm?3), high specific surface area (480–550?m2/g), high porosity (90–95%), and showed bright luminescence upon excitation in the UV range.
Trimethylethoxysilane (TMES) has been recognized as a good co-precursor to increase the degree of hydrophobicity during the synthesis of a silica aerogel because of its methyl groups. Therefore, some physical properties of silica aerogels, including the contact angle and porosity, were investigated using TMES as a co-precursor at different molar ratios with the main precursor such as tetramethoxysilane (TMOS) or tetraethoxysilane (TEOS). In contrast to TMES, most silylating agents such as hexamethyldisilazane (HMDZ) and trimethylchlorosilane (TMCS) have been used for surface modification because of their ability to enhance the hydrophobicity of the aerogel surface. This work examines the silylation effect, which includes increasing hydrophobicity by TMES to determine the possibility of using it as an alternative silylating agent during ambient pressure drying in the synthesis of sodium silicate-based silica aerogel. In addition, the physical properties of sodium silicate-based silica aerogels with silylation under different TMES/TMCS volume ratio are investigated. The physical properties of sodium silicate-based aerogels can be changed by the TMES/TMCS volume ratio during the surface modification step. Aerogels with a high specific surface area (458?m2/g), pore volume (3.215?cm3/g), porosity (92.7%), and contact angle (131.8°) can be obtained TMES/TMCS volume ratio of 40/60.
Phase pure, mesoporous, and crystalline V2O5 is synthesized by acid hydrolysis technique and subsequently heat treatment is carried out at 450, 500, 550, and 600?°C in air. The as-synthesized and heat-treated powders are thoroughly studied by X-ray diffraction, electron microscopy, dynamic light scattering, and spectroscopic techniques. A unique morphological tuning of V2O5 powders from as small as ~80?nm tiny nanorod to as large as a ~2.5?μm hexagonal grain as microstructural unit blocks is observed. A qualitative mechanism is suggested for particle growth. Further, the powders are pelletized and subsequently sintered in air at the same temperatures of 450, 500, 550, and 600?°C at which the powders were heat treated. Finally, nanomechanical properties of bulk pelletized V2O5 such as nanohardness and Young’s modulus are also evaluated by nanoindentation technique at nine different loads e.g., 10, 30, 50, 70, 100, 300, 500, 700, and 1000?mN.
A new chemical approach for the fabrication of Fe3O4 embedded ZnO magnetic semicondutctor composite is reported. The method consists in increasing the pH of the synthesis solution by the thermal decomposition of urea instead of using common alkaline agents, such as NaOH and NH4OH. The material (Fe3O4@ZnO) was used as a platform for the fabrication of highly dispersed gold nanoparticles (~5?nm). The catalytic efficiency of the material, Fe3O4@ZnO@Au, was tested in the photodegradation of Rhodamine-B solutions, and prominent catalytic efficiency, stability, and recycling were achieved. A single portion of the catalyst could be used up to five times without significant loss of activity and its photodegradation efficiency was considered high even after the 12th cycle (56%). Catalyst separation after each batch could be easily achieved because of the intrinsic magnetic property of the material. Leaching monitoring of free Zn species during the fabrication of the catalyst suggests that the use of urea decreased substantially the formation of non-magnetic-semiconducting species and provided a higher mass yield of the magnetic composite compared to an analogous protocol using NaOH. The catalyst was also characterized by detailed structural and chemical analyses, such as transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and vibration sample magnetometer (VSM).
TiO2/WO3 nanocomposite with nanodisk morphology was prepared and successfully used as a photocatalyst. The nanocomposite was obtained via sonochemical and hydrothermal methods, using pomegranate juice as a capping agent. The products were characterized by FE-SEM imaging, BET, EDAX spectroscopy, X-ray diffraction, DRS, and FT-IR spectroscopy. TiO2/WO3 nanocomposite showed high sensitivity to absorb visible light in compared to TiO2. In an optimized condition, the yield of the aerobic photocatalytic oxidation of benzyl alcohol derivatives reached to 65% for the TiO2/WO3 nanocomposite, while the conversion percent of the derivatives was less than 8% and 50% on the TiO2 and WO3 nanoparticles, respectively. Experimental results were supported by density functional theory (DFT) calculations. The DFT results in several solvents of different dielectric constants, confirmed the strong dependence of light absorption and photocatalytic activity to adsorption energy of the substrates on the surface of the nanoparticles (Ead). In addition, the theoretical results showed an inverse correlation between the adsorption energy of benzyl alcohol and its conversion percent, accordance to the experimental trend.
Superhydrophilic surfaces without the need of other stimuli are usually realized by constructing a rough morphology. However, constructing rough surfaces usually require specialized equipment or complicated processing. Besides, rough surfaces can cause undesirable scattering, which strongly limits the use in optical devices. In this article, we prepared superhydrophilic TiO2 films with ultra-smooth surfaces using simple sol-gel dip-coating method. The hydrophilicity of the TiO2 films varied with different post-heat treatments. The films heat-treated at 400?°C exhibited a durable superhydrophilicity and anti-fogging property. This superhydrophilicity was attributed to the decrease of surface hydrophobic alkoxy groups and the formation of point defects, i.e., Ti3+ and oxygen vacancies, which are favourable for dissociative water adsorption. The amount of surface organic groups was influenced by autophobicity effects, further hydrolysis and decomposition of residual alkoxy groups. Additionally, the wettability behaviours of the films were also explained from the perspective of the surface energy. These results can benefit the design and manufacture of anti-fogging and self-cleaning superhydrophilic TiO2 films.
Herein, porous Li3V2(PO4)3/C microspheres made of nanoparticles are obtained by a combination of sol spray-drying and subsequent-sintering process. Beta-cyclodextrin serves as a special chelating agent and carbon source to obtain carbon-coated Li3V2(PO4)3 grains with the size of ca. 30–50?nm. The unique porous structure and continuous carbon skeleton facilitate the fast transport of lithium ion and electron. The Li3V2(PO4)3/C microspheres offer an outstanding electrochemical performance, which present a discharge capacity of 122?mAh?g?1 at 2?C with capacity retention of 96% at the end of 1000 cycles and a high-rate capacity of 113?mAh?g?1 at 20?C in the voltage window of 3.0–4.3?V. Moreover, the Li3V2(PO4)3/C microspheres also give considerable cycling stability and high-rate reversible capacity at a higher end-of-charge voltage of 4.8?V.
Nanocomposites of reduced graphene oxide (rGO) coupled gadolinium doped ZnFe2O4 (GZFG) have been successfully one pot in-situ synthesized adopting low temperature solution process from zinc nitrate, iron nitrate, gadolinium acetate and graphene oxide with varying concentrations of gadolinium (upto 10% Gd with respect to Zn) in the precursor medium. X-ray diffraction and transmission electron microscopy studies confirm the presence of single phase cubic spinel structure of ZnFe2O4 that uniformly distributed over the rGO layers. With increasing Gd doping concentration in precursor medium, the average crystallite size of ZnFe2O4 diminishes gradually from ~11 to ~5.5?nm. Raman and X-ray photoelectron spectral analyses confirm an existence of interaction between rGO and ZnFe2O4 in GZFG samples. Using antibiotic levofloxacin in water, the drug removal capacity (DRC) of GZFG has been performed by optimization of parameters such as gadolinium doping concentration in precursor medium, solution pH, etc. However, the gadolinium doping leads to an improvement in DRC of the nanocomposite and the 5% Gd doped sample shows about 86% DRC at the optimized condition. This simple strategy can be utilized in the synthesis of rGO coupled Gd doped other metal oxide nanocomposites for DRC application.
This paper reports a successful preparation of a pure forsterite Mg2SiO4 using the sol–gel approach and its application for the removal of impurities from a Tunisian frying oil. Magnesium nitrate hexahydrate and tetraethylortho-silicate were used as magnesium and silicon precursors, respectively. The synthesis was held at different calcination temperatures for 30?min. The annealed samples were characterized by X-ray diffraction, Fourier transform infrared, scanning electron microscopy, and laser diffraction. The results revealed that the sample calcined at 500?°C was forsterite with unimodal particle size distribution (PSD) centered at 122.8?±?0.3?μm. The dispersion index I (indicator of particle size uniformity) was 1.84. With the temperature increase, well crystallized compounds were obtained. Their PSDs remain unimodal and shift towards smaller particles. A decrease of the dispersion index was also noted, indicating the formation of Mg2SiO4 with more uniform particle size. This study showed that 900?°C could be selected as energy saving temperature suitable for the preparation of a pure and well crystallized Mg2SiO4 within just 30?min of annealing time. The obtained silicate exhibited promoting results for the purification of waste frying oils.
Pure and fine Mg2SiO4 powder with unimodal particle size distribution was prepared by sol gel route under energy saving conditions. The obtained magnesium orthosilicate showed excellent results for waste frying oil purification
Flower-like ceria (CeO2) architectures consisting of well aligned nanosheets were first synthesized by a glycol solvothermal method. The size of CeO2 architectures is about 5?μm in width and 10?μm in length, with the nanosheets thickness below 100?nm. Subsequently, the adsorbed Ag ions on the surface of CeO2 were in situ reduced to form Ag nanoparticles (NPs), leading to the fabrication of Ag/CeO2 hybrid architectures (HAs). The formed Ag NPs with sizes of 20–40?nm were uniformly loaded on the surface of the CeO2 sheets. The antibacterial properties of Ag/CeO2 HAs against Gram-negative E. coli and Gram-positive S. aureus were evaluated by minimum inhibitory concentration (MIC), minimum bactericidal concentration (MBC), and a filter paper inhibition zone method. The results demonstrated that Ag/CeO2 HAs displayed excellent antibacterial activity toward S. aureus and E. coli, which were attributed to the synergistic antibacterial effect between Ag NPs and CeO2 in HAs. Here, CeO2 nanoflowers as a new substrate could restrict Ag NPs aggregations and improve their antibacterial activities. Therefore, the resulted Ag/CeO2 HAs would be considered as a promising antibacterial agent.
CaMn7O12 precursor sol was prepared by using Ca(NO3)2·4H2O and Mn(CH3COO)4·4H2O as the raw materials, acetylacetone (AcAcH) as the chelating agent, and methyl alcohol (MeOH) as the solvent. The CaMn7O12 crystalline film was obtained via dip-coating and annealing treatment on the LaAlO3 (001) single-crystal substrate. XRD θ-2θ scan indicated that the as-prepared CaMn7O12 film had strong preferred orientation along the c-axis. In addition, the results of the ω and ? scans demonstrated that the film exhibited outstanding out-of-plane and in-plane texture characteristics. The SEM characterization showed that the CaMn7O12 film was dense and free of cracks. The grain size was uniform with an average size of ~180?nm. Vibrating sample magnetometer (VSM) test results indicated the CaMn7O12 film was antiferromagnetic and had a saturation magnetization of 114.2?emu/cm3 at 50?K.
