Effect of the modifier ion on the properties of MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> pigments

Magnesium and zinc ferrites have been prepared by the polymeric precursor method. The organic material decomposition was studied by thermogravimetry (TG) and differential thermal analysis (DTA). The variation of crystalline phases and particle morphology with calcination temperature were investigated using X-ray diffraction (XRD) and scanning electronic microscopy (SEM), respectively. The colors of the ferrites were evaluated using colorimetry. Magnesium ferrite crystallizes above 800°C, presenting a yellow- orange color with a reflectance peak at the 600–650 nm range, while zinc ferrite crystallizes at 600°C, with a reflectance peak between 650–700 nm, corresponding to the red-brick color.     

Ca- and Al-doped ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles as possible anode materials

Spinel ferrites are an amazing class of materials that can find application in different fields, from sensors and lithium-ion batteries to the intriguing biomedical field. For the use as anode in lithium-ion batteries, ZnFe₂O₄ is rather competitive due to low price, abundance, environmental benignity, working voltage of ~1.5 V, and, most importantly, a high theoretical specific capacity (~1072 mA h g^?1). For its practical application, however, some issues must be overcome, in particular its fast capacity fading and poor rate capability resulting from an inherent low electronic conductivity. Possible strategies are represented by ferrite carbon coating/embedding, peculiar synthesis routes, and doping. In this frame, we synthesized Ca- and Al-doped ZnFe₂O₄ nanoparticles by using microwave-assisted combustion synthesis, followed by a classical carbon coating (determined as about 5 wt% by thermogravimetry). A good solubility of Ca and Al up to 25 atom% on both Zn and Fe sites was obtained. Cyclic voltammetries evidenced redox reactions involving Zn and Fe ions, but also the Al intervention could be supposed. Galvanostatic charge–discharge cycles proved that particularly Al ions were useful to improve the anode structural stability at high C rate (up to 3C), thanks to the stronger Al–O bonds with respect to Fe–O ones. A further improvement of capacities comes from the use of sodium alginate as binder to substitute polyvinylidene fluoride in the anode preparation.     

Comparison of the Solubility of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>, Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> in High Temperature Water

As the solubility is a direct measure of stability, this study compares the solubilities of ZnFe₂O₄, Fe₃O₄ and Fe₂O₃ in high temperature water. Through literature analysis and formula derivation, it is shown that it is reasonable to assume ZnFe₂O₄ and Fe(OH)₃ coexist when ZnFe₂O₄ is dissolved in water. Results indicated that the solubility of ZnFe₂O₄ is much lower than that of Fe₂O₃ or Fe₃O₄. The low solubility of ZnFe₂O₄ indicates that it is more protectively stable as an anticorrosion phase. Moreover, the gap between the solubility of ZnFe₂O₄ and that of Fe₃O₄ or Fe₂O₃ was enlarged with an increase of temperature. This means that ZnFe₂O₄ is more protective at higher temperatures. Further analysis indicated that with the increase of temperature, the solubility of ZnFe₂O₄ changed little while those of Fe₂O₃ or Fe₃O₄ changed a lot. Little change of the solubility of ZnFe₂O₄ with increase of temperature showed that ZnFe₂O₄ is stable. The very low and constant solubility of ZnFe₂O₄ suggests that it is more protective than Fe₂O₃ and Fe₃O₄, especially in water at higher temperature.     

Effect of SO<Subscript>2</Subscript> on chlorination of zinc ferrite ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and a mixture of ZnO and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Results of thermodynamic calculations and kinetic studies of the reaction of zinc ferrite ZnFe₂O₄ and of a mixture of oxides, ZnO and Fe₂O₃, with chlorine and SO₂ are presented.     

Nonstoichiometric Zn Ferrite and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Composite Spheres: Preparation,Magnetic Properties,and Chromium Removal

Monodisperse and porous nonstoichiometric Zn ferrite can be prepared by a solvothermal method. Such non-Zn ferrite was used to be the precursor for synthesis of ZnFe₂O₄/Fe₂O₃ composite via calcination at 600°C for 3 h in air. X-ray powder diffractometer (XRD) and Energy Dispersive Spectrometer (EDS) proved the nonstoichiometry of Zn ferrite synthesized by solvothermal method and the formation of ZnFe₂O₄/Fe₂O₃ composite via calcination. TEM image showed that non-Zn ferrite spheres with wormlike nanopore structure were made of primary nanocrystals. BET surface area of non-Zn ferrite was much higher than that of ZnFe₂O₄/Fe₂O₃ composite. Saturation magnetization of non-Zn ferrites was significantly higher than that of ZnFe₂O₄/Fe₂O₃ composites. Calcination of non-Zn ferrite resulted in the formation of large amount of non-magnetic Fe₂O₃,which caused a low magnetization of composite. Because of higher BET surface area and higher saturation magnetization, non-Zn ferrite presented better Cr⁶⁺ adsorption property than ZnFe₂O₄/Fe₂O₃ composites.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Green and efficient synthesis of 2, 3-dihydroquinazolin-4(1H)-ones in aqueous medium using ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> catalyst under microwave irradiation

A versatile and environmentally benign protocol for the synthesis of 2, 3-dihydroquinazolin-4(1H)-ones has been successfully performed in water, using ZnFe₂O₄ catalyst from 2-aminobenzamide with different aromatic aldehydes.     

Microwave assisted low temperature synthesis of sodium zirconium phosphate (NaZr<Subscript>2</Subscript>P<Subscript>3</Subscript>O<Subscript>12</Subscript>)

Sodium zirconium phosphate [NaZr₂P₃O₁₂], a potential ceramic matrix for fixation of high level nuclear waste, was synthesized by heating the mixture of sodium carbonate [Na₂CO₃], zirconyl nitrate hydrate [ZrO(NO₃)₂·5H₂O] and ammonium dihydrogen phosphate [NH₄H₂PO₄] in air, in a resistance heated furnace and a microwave heating system respectively in the temperature range 450 to 650°C. The mixture heated for 1 h in a resistance furnace at 450°C yielded a poorly crystalline NaZr₂P₃O₁₂ [NZP]. Increasing the temperature to 650°C produced a highly crystalline product. The same mixture heated in a microwave oven at 450°C for 1 h however, yielded the most crystalline NZP.In an alternate method, the mixture of sodium dihydrogen phosphate (NaH₂PO₄), zirconium dioxide (ZrO₂) and diammonium hydrogen phosphate [(NH₄)₂HPO₄] heated in resistance furnace at 650°C for the same period did not react in air. It also did not yield the pure product at 450°C when heated in microwave assembly for 1 h.The authors thank the Board of Research in Nuclear Sciences (BRNS) of the Department of Atomic Energy (DAE) for the financial support for this work under the project No. 2000/37/19/BRNS/1959 dtd09-02-02.     

In-situ growth of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles on mesoporous carbon nanofibers: a new nanocomposite for nonenzymatic amperometric sensing of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The paper describes a nonenzymatic amperometric H₂O₂ sensor that uses a nanocomposite consisting of Co₃O₄ nanoparticles (NPs) and mesoporous carbon nanofibers (Co₃O₄-MCNFs). The Co₃O₄ NPs were grown in situ on the MCNFs by a solvothermal procedure. The synergetic combination of the electrocatalytic activity of the Co₃O₄ NPs and the electrical conductivity of MCNFs as an immobilization matrix enhance the sensing ability of the hybrid nanostructure. The oxidation current, best measured at 0.2 V (vs. SCE) is linear in the 1 to 2580 μM H₂O₂ concentration range, with a 0.5 μM lower detection limit (at an S/N ratio of 3). The sensor is highly selective even in the presence of common electroactive interferents. It was applied to the determination of H₂O₂ in spiked milk samples.

Open image in new window

Graphical abstract Schematic of the synthesis of a nanocomposite consisting of Co₃O₄ nanoparticles (NPs) and mesoporous carbon nanofibers (Co₃O₄-MCNFs) by a solvothermal procedure. It was used as electrocatalyst for direct oxidation of H₂O₂.

     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Magnetic solid-phase extraction of polycyclic aromatic hydrocarbons using a graphene oxide/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@polystyrene nanocomposite

A magnetic sorbent was fabricated by coating the magnetized graphene oxide with polystyrene (PS) to obtain a sorbent of the type GO-Fe₃O₄@PS. The chemical composition and morphology of the sorbent were characterized. The sorbent was employed for the enrichment of polycyclic aromatic hydrocarbons (PAHs) from water samples. Various parameters affecting the enrichment were investigated. The PAHs were then quantified by gas chromatography with flame ionization detection. Linear responses were found in the range of 0.03–100 ng mL^?1 for naphthalene and 2-methylnaphthalene, and of 0.01–100 ng mL^?1 for fluorene and anthracene. The detection limits (at an S/N ratio of 3) range between 3 and 10 pg mL^?1. The relative standard deviations (RSDs) for five replicates at three concentration levels (0.05, 5 and 50 ng mL^?1) of analytes ranged from 4.9 to 7.4%. The method was applied to the analysis of spiked real water samples. Relative recoveries are between 95.8 and 99.5%, and RSD% are <8.4%.

Open image in new window

Graphical abstract A magnetic sorbent was fabricated by polystyrene coated on the magnetic graphene oxide for the extraction and preconcentration of PAHs in water samples prior to their determination by gas chromatography with flame ionization detection.

     

Facile synthesis of Fe@Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanowires as O<Subscript>2</Subscript> electrode for high-energy Li-O<Subscript>2</Subscript> batteries

Fe@Fe₂O₃ core-shell nanowires were synthesized via the reduction of Fe³⁺ ions by sodium borohydride in an aqueous solution with a subsequent heat treatment to form Fe₂O₃ shell and employed as a cathode catalyst for non aqueous Li-air batteries. The synthesized core-shell nanowires with an average diameter of 50–100 nm manifest superior catalytic activity for oxygen evolution reaction (OER) in Li-O₂ batteries with the charge voltage plateau reduced to ～3.8 V. An outstanding performance of cycling stability was also achieved with a cutoff specific capacity of 1000 milliampere hour per gram over 40 cycles at a current density of 100 mA g^?1. The excellent electrochemical properties of Fe@Fe₂O₃ as an O₂ electrode are ascribed to the high surface area of the nanowires’ structure and high electron conductivity. This study indicates that the resulting iron-containing nanostructures are promising catalyst in Li-O₂ batteries.     

Magnetic solid-phase extraction of imatinib and doxorubicin as cytostatic drugs by Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/graphene oxide nanocomposite

Magnetic solid-phase extraction based on Fe₃O₄/graphene oxide nanocomposites was investigated for the separation, preconcentration and determination of imatinib and doxorubicin in aqueous solutions. Synthesis of Fe₃O₄/graphene oxide was characterized by transmission electron microscopy, energy-dispersive X-ray analyzer and vibrating sample magnetometer. After optimizing the conditions, optimal experimental conditions including sample pH, the amount of the magnetic nanoparticles, the effect of salt concentration and other chemotherapy medications, eluent type and extraction time were studied and established. The method showed good linearity for the determination of doxorubicin and imatinib in the concentration range of 0.01–100 μg mL^?1 in aqueous solutions with limit of detection 1.8 ng mL^?1 for doxorubicin and 1.9 ng mL^?1 for imatinib. The relative recoveries of doxorubicin and imatinib levels were 96.7 and 88.4%, respectively. The results indicate that the present procedure is a suitable method for extraction of imatinib and doxorubicin from environmental water samples.     

Surfactant Assisted Hydrothermal Synthesis of Superparamagnetic ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> Nanoparticles as an Efficient Visible-Light Photocatalyst for the Degradation of Organic Pollutant

Super paramagnetic ZnFe₂O₄ nanoparticles were prepared by a surfactant assisted (ethylamine) hydrothermal method along with heat treatment. The nanoparticles were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, high resolution scanning electron microscopy, Transmission electron microscopy, vibrating sample magnetometer and diffuse reflectance spectra technique. From the analyses, influence of calcination temperature on the structural, vibrational, morphological, magnetic and optical properties of ZnFe₂O₄ nanoparticles were investigated. The ZnFe₂O₄ nanoparticles with an average particle size of 17 nm showed high photocatalytic activity in the degradation of methylene blue (90 %). This work demonstrates that ZnFe₂O4 can be used as a potential monocomponent in visible-light photocatalysis for the degradation of organic pollutants. Furthermore, the products were super paramagnetic and could be conveniently separated within 15 min and recycled by using simple magnet, which is very beneficial for the degradation of organic pollutants.     

Facile synthesis of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Cu<Subscript>2</Subscript>O nanocomposite and its visible light photocatalytic activity for the degradation of cationic dyes

Iron oxide-loaded Cu₂O photocatalysts were prepared by a facile hydrothermal method. The binary mixed metal oxide photocatalyst was characterized by XRD, FE-SEM, FTIR, UV–Vis-DRS, particle size and zeta potential measurements. XRD analysis showed that Fe₂O₃/Cu₂O catalysts were phase pure and highly crystalline in nature. FE-SEM images revealed the formation of nanospherical Fe₂O₃ over the Cu₂O surface during hydrothermal reaction. From UV–Vis diffuse reflectance spectroscopy studies, the optical band gap of the Fe₂O₃/Cu₂O photocatalyst was found to be slightly red-shifted to 1.85 eV, after loading of Fe₂O₃. The zeta potential analysis revealed that the surface of the Fe₂O₃/Cu₂O photocatalyst was negatively charged in neutral solution. The loading of n-type Fe₂O₃ on p-type Cu₂O augments the charge carrier separation at the interface, which was evident from the enhanced photodegradation of organic pollutants (Methylene blue and Rhodamine B dyes) under visible light irradiation.     

Crystal structures of Ti(NH<Subscript>4</Subscript>)<Subscript>2</Subscript>P<Subscript>4</Subscript>O<Subscript>13</Subscript> and Sn(NH<Subscript>4</Subscript>)<Subscript>2</Subscript>P<Subscript>4</Subscript>O<Subscript>13</Subscript>

The characteristics of crystal structures of the titanium(IV) diammonium (Ti(NH₄)₂P₄O₁₃) and tin(IV) diammonium (Sn(NH₄)₂P₄O₁₃) tetraphosphates, which are isostructural with similar silicon(IV) and germanium(IV) salts, have been obtained by the Rietveld method using X-ray powder diffraction data. The compounds crystallize in the triclinic system, space group P \(\overline 1 \), Z = 2, a = 15.0291(7) Å, b = 7.9236(4) Å, c = 5.0754(3) Å, α = 99.168(3)°, β = 97.059(3)°, γ = 83.459(3)° for Ti(NH₄)₂P₄O₁₃ and a = 15.1454(7) Å, b = 8.0103(5) Å, c = 5.1053(3) Å, α = 99.898(6)°, β = 96.806(3)°, γ = 83.881(4)° for Sn(NH₄)₂P₄O₁₃. The structure is refined in the isotropic approximation using the pseudo-Voigt function: R _p = 0.077, R _Bragg = 0.045, R _F = 0.057 for Ti(NH₄)₂P₄O₁₃; R _p = 0.082, R _Bragg = 0.044, R _F = 0.046 for Sn(NH₄)₂P₄O₁₃. The hydrogen atoms of the ammonium cations are placed in the calculated positions. A comparative analysis of the structures of the compounds of the M^IV(NH₄)₂P₄O₁₃ (M^IV = Si, Ge, Ti, Sn) series has been carried out.