Since the late 1960s, ceric hydrogen phosphates have attracted the attention of scientists due to remarkable ion exchange, sorption, proton-conduction and catalytic properties. In this work, through the application of various solvents, we, for the first time, have obtained monolithic aerogels based on ceric hydrogen phosphates with high porosity (~99%) and extremely low density (~10?μg/cm3). The composition and structure of aerogels were thoroughly studied with XRD, TEM, SEM, XPS, low temperature nitrogen adsorption methods, TGA/DSC, Fourier-transform infrared spectroscopy (FTIR) and small-angle neutron scattering (SANS). The aerogels were found to belong to the fibrous macroporous aerogels family.
Bismuth ferrite (BiFeO3) nanopowder have been successfully synthesized for the first time via a microwave-assisted sol-gel combustion method by using citric acid as fuel. The resulting nanopowder was characterized using FT-IR, TG-DTA, XRD, EDX, VSM, SEM, and UV-Vis DRS. A ferromagnetic hysteresis loop with a saturation magnetization (MS) of 0.66?emu?g?1 has been observed at room temperature in the sample. The optical properties of the nanosized BiFeO3 showed its small band gap (=2.08?eV) indicates a possibility of utilizing much visible light for photocatalysis.
Fiber needle felt–silica aerogel composite was successfully prepared by via sol–gel process based on water glass. The thermal conductivity show V-type variation tendency with the increase of water to Si. Thermogravimetric analysis-differential scanning calorimetry analysis revealed that the thermal stability was up to approximately 390.58?°C. It has been found that the fire hazard of the composites decreased with the increased ratio of water to Si according to the cone calorimeter test, which can be characterized by peak heat release rate, fire performance index, and fire growth rate index. The fiber needle felt/aerogels present greatly improved compressive and flexural strength (elastic modulus: 0.1–0.97?MPa; flexural modulus: 0.33–0.66?MPa) while keeping inherent properties of pure silica aerogel: low bulk density (0.166?g/cm3), low thermal conductivity of 0.0236?W/m·K, and high specific surface area (1091.62?m2/g). As a result, the as-prepared composite shows a great potential to be applied in the thermal insulation field.
Dual-network aerogels (HPSA) with improved mechanical property and thermal insulation were prepared by vacuum impregnation of HNTs/PVA aerogels (the first network aerogel, HPA) in tetraethoxysilane (TEOS). Scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, and N2 adsorption–desorption analysis were used to study micromorphology and microstructure of HPSA, while compression tests and thermal conductivity tests were used to investigate related properties. The results showed that the dual-network frame was successfully constructed, this enabled HPSA to display enhanced compressive properties with increased HNTs content. The addition of silica sol improved the mesoporous characteristics including specific surface area and pore volume and also reduced the thermal conductivities. The first network made it possible for HPSA to possess good mechanical property, while SiO2 aerogel allowed HPSA greater thermal insulation. The obtained aerogel samples exhibited a high compressive strength (i.e., 1.36?MPa) and a low thermal conductivity (i.e., 0.022?W/(m?K)). HNTs/SiO2 dual-network aerogels with improved strength and thermal insulation could show great potential in a wide variety of applications.
The mesoporous silica samples with different concentrations of phosphonic acid groups on the surface were obtained by direct template synthesis. The block-copolymer Pluronic P123 was used as a template, and sodium meta-silicate with diethylphosphatoethyltriethoxysilane as precursors. According to the SAXS diffractograms, mesoporous silica samples have a p6mm hexagonal symmetry. In addition, we used sol–gel method to synthesize xerogel with the same groups for comparison. All samples possess high values of specific surface area 615–730?m2/g and sorption pore volume. FTIR and potentiometric titration methods were used to investigate the surface layer of these samples. Sorption properties of the samples with phosphonic acid groups were studied in respect to a row of metal cations, among which we focused on lead(II), cadmium(II), and dysprosium(III) cations.
A novel ZrCO composite aerogel is synthesized using zirconium oxychloride and resorcinol–formaldehyde (RF) as precursors through the sol–gel route and carbothermal reduction process. The effects of different Zr/R molar ratios and calcination temperatures on the physical chemistry properties of ZrCO aerogels are investigated. The ZrCO composite aerogel consists of the C/ZrO2/ZrC ternary aerogel. The results show that with the increase of R/Zr molar ratios, the specific surface area and bulk density increase with calcination temperature up to 1300?°C, but decrease at even temperature (1500?°C). The specific surface area is as high as 637.4?m2/g for ZrCO composite aerogel (R:Zr?=?2:1), which was higher than ever reported. As the heat-treatment temperature increases to 1500?°C, the ZrC crystalline phase occurs and the t-ZrO2 phase still appears within the composite. The thermal conductivity of the carbon fiber mat-reinforced composite aerogel is as low as 0.057?W/m/K at room temperature (25?°C).
Powders of Sm0.6Sr0.4CoO3-δ and La0.6Sr0.4CoO3-δ were synthesized using wet chemical technique. Structural and surface properties of synthesized materials were studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), IR spectroscopy, and scanning electron microscopy (SEM). The influence of pH on the phase state, chemical composition, morphology, and fractal dimension of the synthesized powders were investigated. It was found that the change of pH has the influence on phase composition of synthesized powders. The increase of solution pH allows one to obtain homogeneous samples at lower temperatures down to 900–950?°C.
ZrC–ZrO2 composite ceramic microspheres were prepared by internal gelation combined with carbothermic reduction using fructose as a chelating agent and carbon source. Fructose in the precursor solution formed complex with zirconium ions, which was conducive to the refining of the microstructure of the sintered composite. ZrC–ZrO2 composite with ZrC content as high as 60?wt% could be prepared.
In this paper, fructose was used as a chelating agent and an organic carbon source to prepare ZrCO microspheres by internal gelation and carbothermic reduction. The fructose in the precursor solution could form complex with zirconium ions, which was conducive to the refining of the microstructure of the sintered composite. ZrC–ZrO2 composite with crystal size of ZrO2 and ZrC in nanometer range and ZrC content as high as 60?wt% could be successfully prepared.
The aim of this work was an investigation of structural and electrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) powders. The compounds obtained by sol-gel method are characterized by several techniques: X-ray diffraction (XRD), N2 adsorption–desorption isotherms, scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), electrical and dielectrical measurements. The XRD, SEM and XPS analysis confirmed the formation of ZnFeTiO4 inverse spinel structure. The electrical and dielectrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) were measured by impedance spectroscopy, revealing a decrease in the electrical conductivity and the dielectric constant with Fe content.
Trimethylethoxysilane (TMES) has been recognized as a good co-precursor to increase the degree of hydrophobicity during the synthesis of a silica aerogel because of its methyl groups. Therefore, some physical properties of silica aerogels, including the contact angle and porosity, were investigated using TMES as a co-precursor at different molar ratios with the main precursor such as tetramethoxysilane (TMOS) or tetraethoxysilane (TEOS). In contrast to TMES, most silylating agents such as hexamethyldisilazane (HMDZ) and trimethylchlorosilane (TMCS) have been used for surface modification because of their ability to enhance the hydrophobicity of the aerogel surface. This work examines the silylation effect, which includes increasing hydrophobicity by TMES to determine the possibility of using it as an alternative silylating agent during ambient pressure drying in the synthesis of sodium silicate-based silica aerogel. In addition, the physical properties of sodium silicate-based silica aerogels with silylation under different TMES/TMCS volume ratio are investigated. The physical properties of sodium silicate-based aerogels can be changed by the TMES/TMCS volume ratio during the surface modification step. Aerogels with a high specific surface area (458?m2/g), pore volume (3.215?cm3/g), porosity (92.7%), and contact angle (131.8°) can be obtained TMES/TMCS volume ratio of 40/60.
In this work, sol–gel-based non-stick ceramic coating formulations were prepared and coated onto aluminum panels in order to investigate their surface properties. The effect of the addition of optimal amount of fluorine-containing silane compound (FAS) on the surface and adhesion properties were also investigated. The morphology, structure, and elemental chemical composition of the coatings were characterized by scanning electron microscopy, atomic force microscopy (AFM), energy dispersion spectrum (SEM/EDAX), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS), respectively. Moreover, several properties of the coatings such as cross-cut adhesion, hardness, gloss, and contact angle (CA) were determined. When fluorine was introduced, the pencil hardness was increased to 6H. Fluorinated non-stick ceramic coatings were found to have good adhesion on the aluminum substrates.
MgF2 coating solutions were solvothermally treated at 160?°C for different time periods, this procedure induced crystallization and particle growth. Antireflection coatings prepared on glass from these solutions were compared to films derived from untreated precursor material. Ellipsometric porosimetry (EP) was employed to characterize structural features of coatings on glass as function of annealing temperature. Based on precursor solutions that had undergone solvothermal treatment antireflective coatings with a peak transparency exceeding 99% were prepared on PMMA substrates.
Solvothermal treatment of MgF2 precursor solutions results in crystallization of particles that can directly be applied to PMMA substrates for λ/4 antireflective films.
New silica-based particles embedding iron were synthesized following a freeze-drying-assisted sol–gel route. The samples were preliminary characterized in view of potential applications as theranostic magnetic resonance imaging (MRI) contrast agents and for hyperthermia treatment. The structural changes induced by iron addition were studied by X-ray diffraction, Fourier transform infrared and electron paramagnetic resonance spectroscopies. The addition of Fe2O3 impedes the SiO2 crystallization denoting that iron plays, in this case, the role of a glass network stabilizer. The composition on surface and nearby was analyzed by X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy both before and after samples immersion in simulated body fluid. The results suggest the nominal composition with 5?mol% Fe2O3 added to 0.7SiO2?0.3Na2O matrix of interest for further investigations as potential MRI contrast agent and hyperthermia vector.
Two series of TiO2 thin films were prepared based on soluble precursor powders: The first run originated directly from an alcohol-based coating solution whereas for the second batch the aqueous precursor powder sol had previously undergone a hydrothermal treatment. The respective microstructures were characterized by electron microscopy, the phase evolution was monitored by X-ray diffraction. Ellipsometric porosimetry (EP) was employed to reveal changes of porosity and pore size induced by thermal treatment of the films.
Soluble TiO2 precursor powders were hydrothermally treated to yield coating solutions. Films from these sols were compared with those directly obtained by dissolving the precursor powders. Results indicate that crystallization to anatase is induced under hydrothermal conditions and the resulting films mostly maintain their porosity throughout thermal treatment. In contrast to that coatings processed from as-dissolved precursor powders undergo more extensive densification
In this research, LiMn2O4 nanopowders were synthesized by the sol–gel method using gelatin as a chelating agent. Three categories of samples with various weight ratios of gelatin to the final product, 1:1, 2:1, and 3:1, have been synthesized. The produced gel was dried in a controllable oven with a slow slope up to 250??C and calcined at different temperatures. The results show that the amount of gelatin affects the structural properties such as the formation temperature of the spinel structure, the homogeneity of the size distribution and size of the particles. The sample with the weight ratio of 3:1 of gelatin to the final product has a lower temperature for the formation of LiMn2O4 with more homogeneity, and smaller particles with the average size of 70?nm, which is calcined at 750??C, while the samples with the weight ratios 2:1 and 1:1 have the average particle sizes of 75 and 89?nm, respectively.
Thermally stable acid catalyzed mesoporous titania (TiO2) nanomatrices are obtained by sol–gel method for fiber optic pH sensing. These synthesized nanoparticles are annealed at 300?°C, at two time intervals i.e., 1?h and 2?h, characterized with several analytical techniques such as FE-SEM/EDS, AFM, XRD, FTIR, TGA, and Brunauer–Emmett–Teller (BET) analysis. Microscopic analysis shows that synthesized nanoparticles have crack-free, dense and homogeneous surface with low surface roughness (4.4–5.9?nm). EDS mapping confirms the uniform distribution of Ti in all samples. XRD findings revealed the TiO2 anatase phase. BET analysis shows that the mesoporous synthesized TiO2 nanoparticles have surface areas 169?m2/g and average pore diameter 39.2?Å. However, surface area is decreased to 113 and 102?m2/g and average pore diameter increased up to 62.36 and 68.18?Å after 1?h and 2?h heat treatment, respectively. Furthermore, the sensing activity of phenolphthalein (phph) doped mesoporous TiO2 nanoparticles/matrix is found to be high at pH 12 without any leaching/cracking.
Boron Nitride (BN) particles were functionalized with vinyl-trimethoxysilane (VTMS) and incorporated into a hybrid polymer (ORMOCER®) resin. The thermal conductivity and mechanical properties of the resulting composite were compared to materials prepared using unmodified particles. Results indicate that the chemical bonding between grain surface and ORMOCER® matrix has a pronounced effect on the final performance of the respective compounds.
The surface of BN particles was functionalized prior to their incorporation into a hybrid polymer (ORMOCER®) matrix, thermal, electrical and mechanical properties of the resulting composites were characterized.
In this study, stearic acid/silica phase change composites were prepared by the sol-gel method using stearic acid as phase change materials (PCMs). The effects of mass fraction of stearic acid were comprehensively investigated. The structures and thermal properties of the obtained composites were characterized by various methods, including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), leakage tests, and thermogravimetry analysis (TG). The results indicated that composite containing 76% stearic acid had the best thermal properties and low mass leakage, making 76% stearic acid as the maximum content that silica matrix could protect in the composites. The latter was further confirmed by morphological analyses of the silica matrix. Silica matrix exhibited spherical particle clusters, following big–small–big–small size pattern as stearic acid rose. The composite with 76% stearic acid was at the key point of change in particle size. These findings look promising for future to prepare silica-based phase change composites with good thermal properties easily.
The simple and effective synthesis of well-defined organosilica hollow nanospheres (OHNSs) for fundamental research and practical applications is still a significant challenge. In this work, a facile “cationic surfactant-induced selective etching” strategy was developed for the fabrication of hollow thiocyanatopropyl silsesquioxanes (thiocyanatopropyl-SQ), mercaptopropyl silsesquioxane (mercaptopropyl-SQ) from cyanoethyl-SQ@thiocyanatopropyl-SQ and cyanoethyl-SQ@mercaptopropyl-SQ, respectively. The experiments demonstrated that cetyltrimethylammonium bromide (CTAB) had remarkable influence on the formation of hollow structure and could accelerate the etching process significantly. A formation mechanism initiated by the adsorption of cationic surfactant followed by the etching of inner core with NH3·H2O was proposed. Hollow thiocyanatopropyl-SQ and mercaptopropyl-SQ with various shell thickness could be prepared by manipulating the amount of CTAB. And large-scale OHNSs were obtained at appropriate concentration of CTAB through this strategy. Moreover, this strategy might be further extended to fabricate OHNSs with other worthy functional groups.
