In this work, sol–gel-based non-stick ceramic coating formulations were prepared and coated onto aluminum panels in order to investigate their surface properties. The effect of the addition of optimal amount of fluorine-containing silane compound (FAS) on the surface and adhesion properties were also investigated. The morphology, structure, and elemental chemical composition of the coatings were characterized by scanning electron microscopy, atomic force microscopy (AFM), energy dispersion spectrum (SEM/EDAX), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS), respectively. Moreover, several properties of the coatings such as cross-cut adhesion, hardness, gloss, and contact angle (CA) were determined. When fluorine was introduced, the pencil hardness was increased to 6H. Fluorinated non-stick ceramic coatings were found to have good adhesion on the aluminum substrates.
Herein, the catalytic properties of the cerium (IV) salt, cerium (IV)-sandwiched polyoxometalate (POM) and cerium (IV)-sandwiched polyoxometalate intercalated in layered double hydroxides (LDHs) in the H2O2-based green oxidation reactions have been evaluated. These cerium (IV)-based systems were applied as homogeneous and heterogeneous catalysts for the oxidation of pyridines. Despite the fact that the cerium (IV)-sandwiched polyoxometalate as a homogeneous reaction system gives good results, there are some disadvantages in recovery and reusability process. To overcome these problems, new nano catalyst was synthesized by intercalation of the Cerium (IV)-sandwiched polyoxometalate into tris(hydroxymethyl) aminomethane-modified layered double hydroxides (Tris-LDH-CO3). The as-prepared nanocomposite was characterized and used as an effective heterogeneous catalyst for the oxidation of pyridines under mild conditions in the presence of H2O2 as an oxidant. The new heterogeneous nanocomposite can be recovered and reused easily from the reaction media at least ten times without significant decrease in catalytic activity.
A series of Al/Ti/Mg-containing ordered mesostructured silicates were synthesized using the natural attapulgite clay as the raw material, which was first pretreated by 4?M hydrochloric acid without other special treatment such as grinding. By varying the pH value in the synthetic gel, different mesophases with cubic, 3D hexagonal, and lamellar mesostructures were obtained. Their mesostructures were confirmed by low-angle X-ray diffraction (XRD) and transmission electron microscopy (TEM). Their morphology and textural properties were analyzed by scanning electron microscopy (SEM) and N2 adsorption. It was found that the hetero-atoms including Al, Ti, and Mg in the clay could be effectively transformed into these ordered mesostructured silicate frameworks in sufficient content, as revealed by inductively coupled plasma (ICP) emission spectroscopy and fourier transform infrared (FT-IR) spectrum. NH3-TPD showed the accessibility of Al species as Brönsted and Lewis acid sites in the mesostructured framework located on the pore surface. All above suggests the potential of attapulgite as a low-cost precursor for the industrial scale production of high quality heteroatom-doped mesophases for various applications. Low-angle powder X-ray diffraction patterns of mesostructured silicates with cubic, 3D hexagonal, and lamellar mesophases, synthesized by using natural clay attapulgite as raw material: uncalcined (left) and calcined (right).
Powders of Sm0.6Sr0.4CoO3-δ and La0.6Sr0.4CoO3-δ were synthesized using wet chemical technique. Structural and surface properties of synthesized materials were studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), IR spectroscopy, and scanning electron microscopy (SEM). The influence of pH on the phase state, chemical composition, morphology, and fractal dimension of the synthesized powders were investigated. It was found that the change of pH has the influence on phase composition of synthesized powders. The increase of solution pH allows one to obtain homogeneous samples at lower temperatures down to 900–950?°C.
In this study, a specific technique was used to quickly, easily, and single step, synthesize core-shell magnetite-silica nanoparticles by controlling the reaction conditions using the proper surfactant. In the first step, the magnetite nanoparticles were prepared by co-precipitation method and silica shell was immediately formed by the sol-gel process. Synthesis was performed at 80?°C with stirring at 12,000?rpm in an alkaline medium. The structural and morphological characteristics of core-shell nanoparticles were examined by XRD, TEM, SEM, and BET analyses. In addition, vibrating sample magnetometer (VSM) was used to evaluate the magnetic characteristics. XRD analysis confirmed the existence of both magnetite and silica phases in the final structure. TEM images showed the presence of nanocomposite particles with core-shell structure of 25?nm diameter. The mean core and shell size were estimated to be about 20 and 2.5?nm, respectively. A study of the magnetic characteristics showed super-paramagnetic behavior with 60?emu/g saturation magnetization (Ms). Due to the high ratio of core size to shell thickness, the magnetic saturation for the synthetized core-shell nanoparticles in this research was significant. In comparison to other multi-step synthesis techniques, the results obtained from this research confirmed the formation of magnetite-silica core-shell structures with the desired magnetic behavior in a quick and single-step process.
MgF2 coating solutions were solvothermally treated at 160?°C for different time periods, this procedure induced crystallization and particle growth. Antireflection coatings prepared on glass from these solutions were compared to films derived from untreated precursor material. Ellipsometric porosimetry (EP) was employed to characterize structural features of coatings on glass as function of annealing temperature. Based on precursor solutions that had undergone solvothermal treatment antireflective coatings with a peak transparency exceeding 99% were prepared on PMMA substrates.
Solvothermal treatment of MgF2 precursor solutions results in crystallization of particles that can directly be applied to PMMA substrates for λ/4 antireflective films.
Zinc doped tin oxide nanoparticles were synthesized by employing sol–gel method assisted with different surfactants namely cetyl trimethyl ammonium bromide (CTAB), hexamine and polyethylene glycol 400 (PEG-400). The synthesis of uniform distribution of spherical Zn-SnO2 nanoparticles in presence of PEG-400 was optimized. The synthesized Zn-SnO2 nanoparticles were characterized by employing standard characterization techniques. X-ray diffraction results confirmed the product high-quality crystalline formation. The photoluminescence peaks appeared at 360?nm revealed the recombination of electron and hole from band to band emission of SnO2 optical properties. The vibrational properties of Zn-SnO2 nanoparticles were confirmed by both Raman and infra red spectra. The spherical morphology and nano sized product was evident in 200?nm scale SEM images. The cyclic voltammetry result of the product Zn-SnO2 assisted PEG-400 exhibited the specific capacitance value of 312.7?F/g at scan rate of 10?mV/s and revealed the superior electrochemical properties. Moreover, the EIS and GCD studies also revealed the good supercapacitor nature with specific capacitance of 132.1?F/g at current density of 1?A/g for the product Zn-SnO2 (PEG-400).
Diagrammatic representation of Zn doped SnO2 synthesis by sol-gel method with enhanced specific capacitance of 132.1?F/g at 1?A/g for Zn-SnO2 (PEG-400).
Two series of TiO2 thin films were prepared based on soluble precursor powders: The first run originated directly from an alcohol-based coating solution whereas for the second batch the aqueous precursor powder sol had previously undergone a hydrothermal treatment. The respective microstructures were characterized by electron microscopy, the phase evolution was monitored by X-ray diffraction. Ellipsometric porosimetry (EP) was employed to reveal changes of porosity and pore size induced by thermal treatment of the films.
Soluble TiO2 precursor powders were hydrothermally treated to yield coating solutions. Films from these sols were compared with those directly obtained by dissolving the precursor powders. Results indicate that crystallization to anatase is induced under hydrothermal conditions and the resulting films mostly maintain their porosity throughout thermal treatment. In contrast to that coatings processed from as-dissolved precursor powders undergo more extensive densification
Boron Nitride (BN) particles were functionalized with vinyl-trimethoxysilane (VTMS) and incorporated into a hybrid polymer (ORMOCER®) resin. The thermal conductivity and mechanical properties of the resulting composite were compared to materials prepared using unmodified particles. Results indicate that the chemical bonding between grain surface and ORMOCER® matrix has a pronounced effect on the final performance of the respective compounds.
The surface of BN particles was functionalized prior to their incorporation into a hybrid polymer (ORMOCER®) matrix, thermal, electrical and mechanical properties of the resulting composites were characterized.
Since the late 1960s, ceric hydrogen phosphates have attracted the attention of scientists due to remarkable ion exchange, sorption, proton-conduction and catalytic properties. In this work, through the application of various solvents, we, for the first time, have obtained monolithic aerogels based on ceric hydrogen phosphates with high porosity (~99%) and extremely low density (~10?μg/cm3). The composition and structure of aerogels were thoroughly studied with XRD, TEM, SEM, XPS, low temperature nitrogen adsorption methods, TGA/DSC, Fourier-transform infrared spectroscopy (FTIR) and small-angle neutron scattering (SANS). The aerogels were found to belong to the fibrous macroporous aerogels family.
The mesoporous silica samples with different concentrations of phosphonic acid groups on the surface were obtained by direct template synthesis. The block-copolymer Pluronic P123 was used as a template, and sodium meta-silicate with diethylphosphatoethyltriethoxysilane as precursors. According to the SAXS diffractograms, mesoporous silica samples have a p6mm hexagonal symmetry. In addition, we used sol–gel method to synthesize xerogel with the same groups for comparison. All samples possess high values of specific surface area 615–730?m2/g and sorption pore volume. FTIR and potentiometric titration methods were used to investigate the surface layer of these samples. Sorption properties of the samples with phosphonic acid groups were studied in respect to a row of metal cations, among which we focused on lead(II), cadmium(II), and dysprosium(III) cations.
The behaviour of alginate gel film in response to the tensile load is analysed in this paper. The bubbles of 0.5?mm diameter were embedded in the film by the fluidic method prior to gelation, thus providing uniform voidage over the entire film. Further, the intrinsic porosity of the gel matrix around the voids was varied by removing water through either evaporation under vacuum, or employing lyophilisation. The Poisson’s ratio and the modulus of elasticity were estimated from direct measurements. The viscoelasticity of the gel matrix was characterized from stress-relaxation measurement. The transient response to tensile loading and the evolution of stress contours were studied through numerical simulation in ANSYS. The ultimate strength was studied for the gel films with embedded voids of different sizes. The numerical simulations were validated by experimental measurements.
The aim of this work was an investigation of structural and electrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) powders. The compounds obtained by sol-gel method are characterized by several techniques: X-ray diffraction (XRD), N2 adsorption–desorption isotherms, scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), electrical and dielectrical measurements. The XRD, SEM and XPS analysis confirmed the formation of ZnFeTiO4 inverse spinel structure. The electrical and dielectrical properties of ZnO/Zn2-xFexTiO4 (x?=?0.7, 1, 1.4) were measured by impedance spectroscopy, revealing a decrease in the electrical conductivity and the dielectric constant with Fe content.
ZrC–ZrO2 composite ceramic microspheres were prepared by internal gelation combined with carbothermic reduction using fructose as a chelating agent and carbon source. Fructose in the precursor solution formed complex with zirconium ions, which was conducive to the refining of the microstructure of the sintered composite. ZrC–ZrO2 composite with ZrC content as high as 60?wt% could be prepared.
In this paper, fructose was used as a chelating agent and an organic carbon source to prepare ZrCO microspheres by internal gelation and carbothermic reduction. The fructose in the precursor solution could form complex with zirconium ions, which was conducive to the refining of the microstructure of the sintered composite. ZrC–ZrO2 composite with crystal size of ZrO2 and ZrC in nanometer range and ZrC content as high as 60?wt% could be successfully prepared.
Flower-like ceria (CeO2) architectures consisting of well aligned nanosheets were first synthesized by a glycol solvothermal method. The size of CeO2 architectures is about 5?μm in width and 10?μm in length, with the nanosheets thickness below 100?nm. Subsequently, the adsorbed Ag ions on the surface of CeO2 were in situ reduced to form Ag nanoparticles (NPs), leading to the fabrication of Ag/CeO2 hybrid architectures (HAs). The formed Ag NPs with sizes of 20–40?nm were uniformly loaded on the surface of the CeO2 sheets. The antibacterial properties of Ag/CeO2 HAs against Gram-negative E. coli and Gram-positive S. aureus were evaluated by minimum inhibitory concentration (MIC), minimum bactericidal concentration (MBC), and a filter paper inhibition zone method. The results demonstrated that Ag/CeO2 HAs displayed excellent antibacterial activity toward S. aureus and E. coli, which were attributed to the synergistic antibacterial effect between Ag NPs and CeO2 in HAs. Here, CeO2 nanoflowers as a new substrate could restrict Ag NPs aggregations and improve their antibacterial activities. Therefore, the resulted Ag/CeO2 HAs would be considered as a promising antibacterial agent.
New silica-based particles embedding iron were synthesized following a freeze-drying-assisted sol–gel route. The samples were preliminary characterized in view of potential applications as theranostic magnetic resonance imaging (MRI) contrast agents and for hyperthermia treatment. The structural changes induced by iron addition were studied by X-ray diffraction, Fourier transform infrared and electron paramagnetic resonance spectroscopies. The addition of Fe2O3 impedes the SiO2 crystallization denoting that iron plays, in this case, the role of a glass network stabilizer. The composition on surface and nearby was analyzed by X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy both before and after samples immersion in simulated body fluid. The results suggest the nominal composition with 5?mol% Fe2O3 added to 0.7SiO2?0.3Na2O matrix of interest for further investigations as potential MRI contrast agent and hyperthermia vector.
Natural dyes, namely, indigo carmine, cochineal carmine, curcumin and annatto, were encapsulated in silica by a sol-gel method and applied in the dyeing of different textile fibers by exhaustion. For comparative reasons, dyeing using the free (non-encapsulated) bare dyes was also carried out. The hybrid materials were analyzed by a set of techniques to investigate their elemental, structural, textural and morphological properties, and the results showed that it was possible to obtain stable natural dyes for applications in textile dyeing. The silica-structured dyes showed better affinities with the fibers (WO, PA, PAC and PET) in dyeing with cochineal carmine, while cotton (CO) showed better affinities with the encapsulated curcumin and annatto dyes. The performances of the encapsulated dyes were evaluated by color and washing fastness measurements and resulted in improved dye absorption and wash fastness properties. The color change and color transfer measurements of the encapsulated dyes were better (rated at 4–5 on a scale of 1–5) compared to the bare dyes.
In this study, stearic acid/silica phase change composites were prepared by the sol-gel method using stearic acid as phase change materials (PCMs). The effects of mass fraction of stearic acid were comprehensively investigated. The structures and thermal properties of the obtained composites were characterized by various methods, including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), leakage tests, and thermogravimetry analysis (TG). The results indicated that composite containing 76% stearic acid had the best thermal properties and low mass leakage, making 76% stearic acid as the maximum content that silica matrix could protect in the composites. The latter was further confirmed by morphological analyses of the silica matrix. Silica matrix exhibited spherical particle clusters, following big–small–big–small size pattern as stearic acid rose. The composite with 76% stearic acid was at the key point of change in particle size. These findings look promising for future to prepare silica-based phase change composites with good thermal properties easily.
The influence of the water content in the initial composition on the size of silica particles produced using the Stöber process is well known. We have shown that there are three morphological regimes defined by compositional boundaries. At low water levels (below stoichiometric ratio of water:tetraethoxysilane), very high surface area and aggregated structures are formed; at high water content (>40?wt%) similar structures are also seen. Between these two boundary conditions, discrete particles are formed whose size are dictated by the water content. Within the compositional regime that enables the classical Stöber silica, the structural evolution shows a more rapid attainment of final particle size than the rate of formation of silica supporting the monomer addition hypothesis. The clearer understanding of the role of the initial composition on the output of this synthesis method will be of considerable use for the establishment of reliable reproducible silica production for future industrial adoption.
In the present study, TiO2/ZnO composite nanodot films were prepared and the effects of Zn incorporation on light-induced cell detachment were investigated. The nanodots films, which were successfully synthesized by phase-separation-induced self-assembly method, were characterized on the morphology, composition, microstructure, and other properties, and evaluated on cell compatibility and cell detachment performances as well. Live-dead staining was used to study the viability of cell sheet detached by light illumination. Results shows that with the increasing of introduced Zn, the band gap widened and the absorbance in UV region increased, while the crystallinity and performance of light-induced hydrophilicity weakened. All the nanodots films showed good cell compatibility and cell detachment performance induced by light. The nanodots film which had a Zn/Ti molar ratio of 0.03 showed the highest detachment ratio of 91.0% after 20?min ultraviolet illumination. The prepared TiO2/ZnO composite nanodots films could be helpful in optimizing light-induced cell detachment behavior.
