Restructuring-induced activity of SiO(2)-supported large au nanoparticles in low-temperature CO oxidation

Large Au nanoparticles with an average size of approximately 10 nm supported on inert SiO(2) become active in low-temperature CO oxidation after the addition of NaNO(3). The catalyst structures have been characterized in detail by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and X-ray absorption spectroscopy. The NaNO(3) additive in Au/SiO(2) catalysts does not lead to the formation of fine Au nanoparticles, which are generally considered to be inevitable in low-temperature CO oxidation catalyzed by gold, nor does it alter the electronic structure of Au. The NaNO(3)-induced restructuring of large Au nanoparticles was proposed to create low-coordinated Au sites on the surface capable of catalyzing low-temperature CO oxidation. These results experimentally prove that the activity of supported Au nanoparticles in low-temperature CO oxidation could solely arise from their geometric structure, which greatly deepens the fundamental understandings of Au nanocatalysis.     

Structure and growth of oxides on polycrystalline nickel surfaces

The oxidation of polycrystalline nickel (Ni) metal surfaces after exposure to oxygen gas (O₂) at 25 and 300 °C and pressures near 130 Pa, was studied using X‐ray photoelectron spectroscopy (XPS). Oxide structures involving both divalent (Ni²⁺) and trivalent (Ni³⁺) species could be distinguished using Ni 2p spectra, while surface adsorbed O₂ and atomic oxygen (O) species could be differentiated from bulk oxide (O^2?) using O 1s spectra. Oxide thicknesses and distributions were determined using QUASES^?, and the average oxide thickness was verified using the Strohmeier formula. The reaction kinetics for oxide films grown at 300 °C followed a parabolic mechanism, with an oxide thickness of greater than 4 nm having formed after 60 min. Exposure at 25 °C followed a direct logarithmic mechanism with an oxide growth rate about four to five times slower than at 300 °C. Reaction of a Ni (100) single crystal under comparable conditions showed much slower reaction rates compared to polycrystalline specimens. The higher reaction rate of the polycrystalline materials is attributed to grain boundary transport of Ni cations. Oxide thickness was measured on a microscopic scale for polycrystalline Ni exposed to large doses of O₂ at 25 and 300 °C. The thickness of oxide was not strongly localized on this scale. However, the QUASES^? analysis suggests that there is localized growth on a nanometric scale—the result of island formation. Copyright © 2007 John Wiley & Sons, Ltd.     

Surface oxidation process of a diamond‐like carbon film analyzed by difference X‐ray photoelectron spectroscopy

Difference X‐ray photoelectron spectroscopy (D‐XPS) revealed the surface oxidation process of a diamond‐like carbon (DLC) film. Evaluation of surface functional groups on DLC solely by the C 1s spectrum is difficult because the spectrum is broad and has a secondary asymmetric lineshape. D‐XPS clarified the subtle but critical changes at the DLC surface caused by wet oxidation. The hydroxyl (C―OH) group was dominant at the oxidized surface. Further oxidized carbonyl (C?O) and carboxyl (including carboxylate) (COO) groups were also obtained; however, the oxidation of C?O to COO was suppressed to some extent because the reaction required C―C bond cleavage. Wet oxidation cleaved the aliphatic hydrogenated and non‐hydrogenated sp² carbon bonds (C―H sp² and C―C sp²) to create a pair of C―OH and hydrogenated sp³ carbon (C―H sp³) bonds. The reaction yield for C―H sp² was superior at the surface, suggesting that the DLC film was hydrogen rich at the surface. Oxidation of aromatic sp² rings or polycyclic aromatic hydrocarbons such as nanographite to phenols did not occur because of their resonance stabilization with electron delocalization. Non‐hydrogenated sp³ carbon (C―C sp³) bonds were not affected by oxidation, suggesting that these bonds are chemically inert. Copyright © 2014 John Wiley & Sons, Ltd.     

Ultrasound‐assisted oxidation of tungsten in oxygen plasma: the early stages of the oxide film growth

The effect of ultrasonic vibrations applied in situ on the formation of W–WO interface during the exposure of a pure tungsten foil to a low‐temperature oxygen plasma is investigated by photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS). The tungsten surface was exposed to oxygen plasma at different time intervals and the evolution of the interface formation was studied by angle‐resolved XPS. We show that oxidation without ultrasonic vibrations leads to the formation of a thin oxide film whose growth kinetics is governed by an island growth mechanism. On the other hand, oxide growth in the presence of ultrasonic treatment (UST) appears to follow a layer‐by‐layer growth mode with a distinctly sharper W–WO interface. TOF‐SIMS analysis in this case revealed a reduced amount of water bonded in the film, which suggests an increase in the film's packing density. Copyright © 2006 John Wiley & Sons, Ltd.     

Nanoelectrocatalyst Based on High‐Density Au/Pt Hybrid Nanoparticles Supported on a Silica Nanosphere

A high‐efficiency nanoelectrocatalyst based on high‐density Au/Pt hybrid nanoparticles supported on a silica nanosphere (Au‐Pt/SiO₂) has been prepared by a facile wet chemical method. Scanning electron microscopy, transmission electron microscopy, energy‐dispersive X‐ray spectroscopy, and X‐ray photoelectron spectroscopy are employed to characterize the obtained Au‐Pt/SiO₂. It was found that each hybrid nanosphere is composed of high‐density small Au/Pt hybrid nanoparticles with rough surfaces. These small Au/Pt hybrid nanoparticles interconnect and form a porous nanostructure, which provides highly accessible activity sites, as required for high electrocatalytic activity. We suggest that the particular morphology of the Au‐Pt/SiO₂ may be the reason for the high catalytic activity. Thus, this hybrid nanomaterial may find a potential application in fuel cells.     

The initial oxidation of magnesium: an in situ study with XPS,HERDA and ellipsometry

The initial oxidation of magnesium at oxygen partial pressures between 1.3 × 10^?8 and 1.3 × 10^?5 Pa and at temperatures ranging from 273 to 550 K has been investigated in situ with X‐ray photoelectron spectroscopy (XPS), ellipsometry and high resolution elastic recoil detection analysis (HERDA). Quantitative analysis of the XPS spectra showed a clear oxygen deficiency with respect to MgO for the initial oxide. HERDA measurements confirmed this relatively low oxygen content in the thin oxide layers formed. Ellipsometry measurements showed that the electronic structure of the initially formed oxide differs significantly from that of bulk MgO. The band gap values at room temperature for the oxide layers investigated are clearly smaller than the value for bulk MgO. Copyright © 2006 John Wiley & Sons, Ltd.     

Oxidation‐induced nanostructures on Cu{100}, Cu(Ag) and Ag/Cu{100} studied by photoelectron spectroscopy

Initial surface oxidation and nanoscale morphology on Cu{100}, Cu(Ag) and Ag/Cu{100} have been investigated in situ by X‐ray photoelectron spectroscopy (XPS), X‐ray induced Auger electron spectroscopy (XAES) and the inelastic electron background analysis as a function of oxygen exposure at 3.7 × 10^?2 and 213 mbar pressures at a surface temperature of 373 K. Relative Cu₂O concentrations have been quantified by analysis of the peak shape of the XAES Cu LMM transition. The surface morphology of Cu₂O islands and the Ag layer has been characterized by inelastic electron background analysis of XAES O KLL and Ag 3d transitions. Oxygen‐induced segregation of Cu, as well as the subsequent Cu₂O island formation on Cu(Ag) and Ag/Cu{100} surfaces, has been investigated quantitatively. Our results indicate that Ag has a clear inhibitive effect on the initial oxidation and Cu₂O island formation on Cu(Ag) and Ag/Cu{100} surfaces. The Cu₂O islands are also observed to remain highly strained on Ag/Cu{100} even at higher O₂ exposures. The results suggest that strained Cu₂O islands eventually penetrate through the buried Ag layer, and in conjunction with segregating Cu atoms enable the oxidation to proceed at a similar rate to or even faster than on the unalloyed Cu surface. Copyright © 2007 John Wiley & Sons, Ltd.     

Interlaboratory study comparing analyses of simulated angle‐resolved X‐ray photoelectron spectroscopy data

An interlaboratory study has been conducted to determine the following: (i) the similarities and differences of film thicknesses and composition profiles obtained from analyses of simulated angle‐resolved X‐ray photoelectron spectroscopy (ARXPS) data by different analysts using different algorithms for data analysis, and (ii) the effects of two assumptions commonly made in data‐analysis algorithms for ARXPS on derived film thicknesses and composition profiles. The analyzed data were generated by the National Institute of Standards and Technology Database for the Simulation of Electron Spectra for Surface Analysis, (SESSA) which provides a simple way to study the influence of the aforementioned effects on compositional depth profile reconstruction. Sets of simulated ARXPS data were produced for thin films of SiO₂, SiON, HfO₂, and HfON of varying thicknesses on a Si substrate. For some HfON films, the N concentration varied with depth. Eleven groups participated in the round robin study. The majority (eight) employed a commercial ARXPS instrument in which the angular distribution is measured for a fixed sample geometry, in contrast to conventional ARXPS in which the sample is tilted for angular variation. The average deviations between the reported average depth, film thickness, and amount of material typically varied between 20% and 30% but were considerably larger, between 30% and 80%, for some cases. The average errors were generally larger for simulations that included elastic scattering and the finite analyzer‐acceptance angle (realistic conditions) than those for simulations that neglected elastic scattering and the finite analyzer‐acceptance angle (simplified conditions). The retrieved N depth profiles were quantitatively different from the true depth profiles and showed substantial variability among the group of members who used the same instrument and analysis software. Copyright © 2014 John Wiley & Sons, Ltd.     

In Situ Observation of Surface Species on Iridium Oxide Nanoparticles during the Oxygen Evolution Reaction

An iridium oxide nanoparticle electrocatalyst under oxygen evolution reaction conditions was probed in situ by ambient‐pressure X‐ray photoelectron spectroscopy. Under OER conditions, iridium undergoes a change in oxidation state from Ir^IV to Ir^V that takes place predominantly at the surface of the catalyst. The chemical change in iridium is coupled to a decrease in surface hydroxide, providing experimental evidence which strongly suggests that the oxygen evolution reaction on iridium oxide occurs through an OOH‐mediated deprotonation mechanism.     

XPS与UPS测量几种材料功函数的比较

为比较X射线光电子能谱(XPS)与紫外光电子能谱(UPS)测量材料功函数结果间的差异,依次对经氩离子清洁表面吸附层的Au、Ag薄膜样品和单晶硅片,以及未进行表面清洁的Au、Ag、MoO_3薄膜样品,单晶硅片及ITO导电玻璃的功函数进行测量。给出了XPS和UPS测量功函数的计算方法,并探讨了影响材料功函数测量结果不确定性的因素。研究发现XPS及UPS在测量表面清洁的金属样品时,测量结果基本一致,具有较高的准确度,表面清洁的Au、Ag样品一经暴露空气后其表面覆盖一层吸附层,功函数很快发生变化。利用UPS或XPS测量金属和半导体的功函数时应避免暴露空气,若金属样品在空气中暴露时建议使用氩离子清洁表面。研究结果对科研人员按实际测试需求合理选择测量方法具有一定的指导意义。     

Modification of glassy carbon electrode by the electrochemical oxidation of 3‐aminophenylcalix[4]pyrrole in nonaqueous media

3‐Aminophenylcalix[4]pyrrole (3APCP) was grafted to a glassy carbon (GC) surface during the electrochemical oxidation process in 0.1 M tetrabutylammoniumtetra‐fluoroborate (TBATFB) containing acetonitrile solution. The presence of a surface film was confirmed electrochemically by comparing voltammograms of dopamine and ferricyanide redox probes at the bare and modified electrodes. Reflection‐absorption infrared spectroscopy (RAIRS), XPS, atomic force microscopy (AFM), ellipsometry and the contact angle measurements were also employed to characterize 3APCP film on GC electrode. RAIRS analysis revealed that calix[4]pyrrole was bonded to the glassy carbon surface via the etheric linkage. The stability of the modified GC electrode was also studied. Copyright © 2011 John Wiley & Sons, Ltd.     

The investigation of NbO2 and Nb2O5 electronic structure by XPS,UPS and first principles methods

In this paper, the electronic structures of NbO₂ and Nb₂O₅ are theoretically and experimentally analyzed. The oxides in the samples are mainly consisted of NbO₂ and NbO, whereas the outmost layer of the samples is NbO₂. After exposure to air, the outermost layer on all niobium samples is Nb₂O₅. The photoelectrons from the first 2–4 Å contribute to the spectra, so the valence band structure of NbO₂ and Nb₂O₅ can be confirmed from ultraviolet photoelectron spectroscopy (UPS). By comparing the UPS with density of state results, the electronic structure of NbO₂ and Nb₂O₅ can be distinguished from each other, and then the electronic structure was deconvoluted into several electronic states. The agreement between experimental result and theory is, in the best case, satisfactory. Copyright © 2013 John Wiley & Sons, Ltd.     

New Insights into Sulfur Deposition on Gold Using Dithiobisphthalimide as a New Precursor

Dithiobisphthalimide is used as a new precursor for the spontaneous deposition of sulfur on gold surfaces in acetonitrile. Characterization of the modified surfaces is achieved using X‐ray photoelectron spectroscopy (XPS), electrochemistry and scanning tunneling microscopy (STM). The reported results indicate that the sulfur deposition is an efficient and fast process and that high coverages can be reached very quickly. Sequential high‐resolution STM in air allows the direct observation, for the first time, of the mobility of the usually observed rectangular structures as individual units. It also shows the reversible association/dissociation of these rectangles. The nature of these structures is highly debated in the literature and the present work provides new insights into their nature through the use of a new sulfur precursor under non‐traditional conditions. To explain our results we consider these structures as simple sulfur adlayers on the gold surface.     

XPS characterisation of carbon‐coated alumina support

Hybrid carbon–alumina supports, synthesised by pyrolysis of grafted 4,4′‐methylenebis‐(phenylisocyanate) moiety on the alumina surface, were characterised by X‐ray photoelectron spectroscopy. The recorded Al 2p and C 1s envelopes showed asymmetry that decreased with an increase in carbon loading. In all experimental Al 2p envelopes, the high‐energy individual components at 75.3–75.9 eV were present along with the low‐energy component at 74.0 eV typical for Al₂O₃. In the case of the C 1s envelope, the component around 284.3–284.4 eV and three high‐energy individual components at 285.9–286.0, 288.0–288.3 and 290.1–290.6 eV were observed. The presence of the high‐energy Al 2p components can be explained considering the occurrence of a steady‐state charging of the different parts of insulating alumina supports. The component around 284.3–284.4 eV in C 1s envelopes can be attributed to carbon, which constitutes the coating and, hence, ensures surface conductivity. The component around 285.9–286.0 eV is connected with carbon in carbonaceous surface species, which do not form the conducting layer on the alumina support. Carbonaceous surface species associated with C? O, C?O and O?C? O groups in carbon coating can be also identified due to the presence of corresponding components in XPS spectra at 285.9–286.0, 288.0–288.3 and 290.1–290.6 eV. Copyright © 2006 John Wiley & Sons, Ltd.     

GDOES,XPS, and SEM with EDS analysis of porous coatings obtained on titanium after plasma electrolytic oxidation

In the paper, the glow discharge optical emission spectroscopy, X‐ray photoelectron spectroscopy, scanning electron microscopy, and energy‐dispersive X‐ray spectroscopy results of a commercial purity titanium grade 2 after plasma electrolytic oxidation (PEO), also known as micro arc oxidation (MAO), are presented. The PEO treatment was performed in the electrolyte containing concentrated (85%) phosphoric acid with copper nitrate at the voltage of 450 ± 10 V for 1 min. For the electrolyte, copper nitrate addition from 300 to 600 g/l was used. Porous coatings of specific properties were obtained. The measurements results allow to state that the copper and nitrogen ions can be introduced into the surface layer formed on pure titanium by the plasma electrolytic oxidation. The distributions of these elements were detected to depend on the electrolyte composition, with the highest amounts revealed in the coating created in the electrolyte containing 600 g Cu(NO₃)₂ in 1 l H₃PO₄. Three sub‐layers of the coating, displayed in this work by two models, were developed in the study. The analysis performed shows that under the PEO treatment in each of the electrolytes used, the formation of coating with the top sub‐layers always enriched in copper compounds was found. Copyright © 2016 John Wiley & Sons, Ltd.