Synthesis of anatase TiO2 nanowires by modifying TiO2 nanoparticles using the microwave heating method

Anatase TiO₂ nanowires with a diameter of 5-10 nm and length of 500 nm to 2 μm have been successfully synthesized by modifying TiO₂ nanoparticles (P25) using the microwave heating method. The microwave power, reaction pressure, and reaction time for the synthesis of TiO₂ nanowires were 500 W, 0.5-3.0 MPa (corresponding to a temperature range of 175-260), and 40-70 min, respectively. X-ray diffraction (XRD), field-emission scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and the BET techniques were used to investigate the phase structures, morphologies, and specific surface areas of the TiO₂ nanowires. The effects of reaction time, pressure, and different post-treatment processes on the microstructures of TiO₂ nanowires were discussed. It has been shown that the microwave heating method is efficient in transforming TiO₂ nanoparticles to anatase TiO₂ nanowires.     

Synthesis, structure and antiferromagnetic behaviour of brannerite MnV2O6

Brannerite MnV 2 O 6 with plate-like shape is successfully synthesized by hydrothermal method.Its crystal structure and morphology are investigated by x-ray diffraction (XRD),scanning electron microscopy (SEM),transmission electron microscope (TEM),high resolution transmission electron microscopy (HRTEM) and select area electronic diffraction (SAED).The results show that the brannerite MnV 2 O 6 with monoclinic structure has a uniform plate-like shape with a diameter of about 5-8 μm and a thickness of about 500 nm.SAED patterns further confirm the structure of the brannerite MnV 2 O 6 and the single crystalline character of the plate crystal.Magnetic properties are measured by superconducting quantum interference device (SQUID) in a temperature range of 2-300 K under a magnetic field of 1 T.The magnetic measurement results indicate that the material undergoes an antiferromagnetic transition with a N’eel temperature of 17 K.Above 50 K,the inverse susceptibility is fitted well to the Curie-Weiss law with a calculated moment of 5.98 μ B.Finally,the origin of antiferromagnetic behaviour in the brannerite MnV 2 O 6 is explained by means of Anderson model.     

钙钛矿型纳米BaFeO3的制备、结构表征及铁磁性研究

采用溶胶-凝胶法制备出钙钛矿型纳米BaFeO₃粉末,利用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)分析研究了其微观结构及形貌,结果表明：胶体试样经800℃退火处理后,形成了20nm左右的钙钛矿型BaFeO₃粉末,其(110)面晶面间距为0.280nm左右,(100)面晶面间距为0.401nm左右.利用振动样品磁强计(VSM)研究了纳米BaFeO₃粉末的室温铁磁性能,测量结果表明：在室温条件下,纳米BaFeO关键词： 溶胶-凝胶法 3')" href="#">钙钛矿型纳米BaFeO₃ 铁磁性 氧空位     

Bi2Te3/Sb超晶格纳米线的外延生长和热电测量

通过脉冲电沉积,外延生长出小单元长度的Bi₂Te₃/Sb超晶格纳米线.借助哈曼方法,测量了超晶格纳米线阵列的热电性能,330 K时的ZT值可达0.15.研究了Bi₂Te₃/Sb超晶格纳米线阵列器件的制冷或者加热能力,发现器件的上下表面的最大温差可以达到6.6 K.     

Synthesis and characterization of Zn3P2/ZnS core/shell nanowires

Fully-surrounded Zn₃P₂/ZnS core/shell nanowires (NWs) were synthesized for the first time via a two-step method: a catalyst free chemical vapor deposition followed by a low-pressure vulcanization process. Field emission scanning electron microscopy, high-resolution transmission electron microscopy, and high-angle angular dark field scanning transmission electron microscopy were used to characterize the morphologies, crystal structure, and element composition of the core/shell NWs. The band structure analysis demonstrates that the Zn₃P₂/ZnS core-shell NW type-II heterostructures have bright potential in photovoltaic nanodevice applications. The core/shell NW growth method used here can be extended to other material system.     

SnO2 nanowires mixed nanodendrites for high ethanol sensor response

Mixed morphology of SnO₂ nanowires and nanodendrites was synthesized on the gold-coated alumina substrates by carbothermal reduction of SnO₂ in closed crucible. The products were characterized by scanning electron microscopy, x-ray diffractometer, and transmission electron microscopy. Results showed the SnO₂ nanowires and the SnO₂ nanodendrites branched out from the main nanowires. Both SnO₂ nanostructures were pure tetragonal rutile structure. The nanowires were grown in [101] and directions with the diameter of 50–150 nm and the length of a few 10 μm. The nanodendrites were about 100–300 nm in diameter. The growth mechanism of the SnO₂ nanostructures was also discussed. Characterization of ethanol gas sensor, based on the mixed morphology of the SnO₂ nanostructures, was carried out. The optimal temperature was about 360 °C and the sensor response was 120 for 1000 ppm of ethanol concentration.     

Synthesis of β-Ga2O3 nanowires through microwave plasma chemical vapor deposition

In this study, we demonstrate the large-scale synthesis of beta gallium oxide (β-Ga₂O₃) nanowires through microwave plasma chemical vapor deposition (MPCVD) of a Ga droplet in the H₂O and Ar atmosphere at 600 W. Unlike the commonly used MPCVD method, the H₂O, not mixture of gas, was employed to synthesize the nanowires. The ultra-long β-Ga₂O₃ nanowires with diameters of about 20-30 nm were several tens of micrometers long. The morphology and structure of products were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM) and high-resolution transmission electron microscope (HRTEM). The growth of β-Ga₂O₃ nanowires was controlled by vapor-solid (VS) crystal growth mechanism.     

Stimulated emission from trapped excitons in SnO2 nanowires

The pump fluence dependent photoluminescence (PL) spectra of SnO₂ nanowires were investigated, which were synthesized with a high-temperature chemical reduction method. The integrated intensity of the narrower peak at 3.2 eV experiences a strong superlinear dependence on the pump fluence, and the narrowest width of the sharp peak is only 19 meV. Moreover, under high excitation fluence, an ultrafast decay time (less than 20 ps) appears in the time-resolved PL spectra. The emission of these SnO₂ nanowires shows strong apparent stimulated emission behaviors although the SnO₂ is a dipole forbidden direct gap semiconductor. The stimulated emission should relate to the localized islands on the surface of nanowire, which was observed through the high resolution transmission electron microscopy (HRTEM) image. The giant-oscillator-strength effect of bound exciton generated from the localized islands was considered to induce the stimulated emission of SnO₂ nanowires.     

Green synthesis and characterization of superparamagnetic Fe3O4 nanoparticles

In this paper, we have first demonstrated a facile and green synthetic approach for preparing superparamagnetic Fe₃O₄ nanoparticles using α-d-glucose as the reducing agent and gluconic acid (the oxidative product of glucose) as stabilizer and dispersant. The X-ray powder diffraction (XRD), X-ray photoelectron spectrometry (XPS), and selected area electron diffraction (SAED) results showed that the inverse spinel structure pure phase polycrystalline Fe₃O₄ was obtained. The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results exhibited that Fe₃O₄ nanoparticles were roughly spherical shape and its average size was about 12.5 nm. The high-resolution TEM (HRTEM) result proved that the nanoparticles were structurally uniform with a lattice fringe spacing about 0.25 nm, which corresponded well with the values of 0.253 nm of the (3 1 1) lattice plane of the inverse spinel Fe₃O₄ obtained from the JCPDS database. The superconducting quantum interference device (SQUID) results revealed that the blocking temperature (T_b) was 190 K, and that the magnetic hysteresis loop at 300 K showed a saturation magnetization of 60.5 emu/g, and the absence of coercivity and remanence indicated that the as-synthesized Fe₃O₄ nanoparticles had superparamagnetic properties. Fourier transform infrared spectroscopy (FT-IR) spectrum displayed that the characteristic band of Fe-O at 569 cm⁻¹ was indicative of Fe₃O₄. This method might provide a new, mild, green, and economical concept for the synthesis of other nanomaterials.     

Growth of branched rutile TiO2 nanorod arrays on F-doped tin oxide substrate

Branched rutile TiO₂ nanorod arrays were directly synthesized on the F-doped tin oxide (FTO) substrate through a two-step hydrothermal treatment by a seeding method with TiO₂-nanorods as seeds. The samples were characterized respectively by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and field-emission scanning electron microscopy (FESEM). Results showed that TiO₂ nanorods with nanobranches (TiO₂-NB) grew vertically on the FTO substrate. XRD and HRTEM results confirmed that the TiO₂-NB arrays were single-crystalline rutile. The optical properties of the samples were studied with a UV-vis spectrometer. The photocatalytic activity of the TiO₂-NB film is better than that of P25 particulate film. Direct electrical pathway and improved light-harvesting efficiency were crucial for the superior photocatalytic activity of the TiO₂-NB arrays.     

氧离子导体La1.9Y0.1Mo2O9细晶粒陶瓷的制备和电学性质研究

采用溶胶凝胶法合成的La_1.9Y_0.1Mo₂O₉纳米晶粉体, 结合微波烧结技术制备出不同晶粒度的La_1.9Y_0.1Mo₂O₉块体样品. 利用X射线衍射仪(XRD)、高分辨透射显微镜(HRTEM)、场扫描显微镜(SEM)对粉体及陶瓷块体的物相、 形貌进行了表征, 利用交流阻抗谱仪测试了样品不同温度下的电导率. 实验结果表明, 掺Y的La_1.9Y_0.1Mo₂O₉能将高温立方β 相稳定到室温; 块体样品致密均匀, 平均晶粒度范围在60 nm–4 μm之间; 致密度高的样品表现出高的电导率, 其中900 ℃烧结样品的电导率600 ℃时高达0.026 S/cm, 比固相反应法制备的La_1.9Y_0.1Mo₂O₉样品高出约1倍. 总结认为样品的致密性对电导率影响较大, 是通过影响晶界电导率来影响总电导率的, 样品的晶粒度(在60 nm–4 μm范围内)对电导率的影响还不能确定. 关键词： 氧离子导体 1.9Y_0.1Mo₂O₉')" href="#">La_1.9Y_0.1Mo₂O₉ 细晶粒陶瓷 微波烧结     

Preparation, structure and photo-catalytic performances of hybrid Bi2SiO5 modified Si nanowire arrays

Bi₂SiO₅ modified Si nanowire array films were fabricated as photo-catalysts via dip-coating Bi(NO₃)₃ on silver-assisted electroless wet chemical etching Si nanowires and subsequently annealing. The structures and morphologies of as-prepared samples are characterized by X-ray diffraction, Fourier transform infrared spectrum, scanning electron microscopy and transmission electron microscopy. The results of photocatalytic experiments indicated that the Bi₂SiO₅ modified Si nanowire arrays benefit the improvement for efficient electron-hole separation and photo-catalytic stability, thereby possessing superior photo-degradation performance. These hybrid nanowire arrays will be promising materials for photo-catalysts and degradation agents.     

Synthesis of nanocrystalline Zn0.5Mn0.5Fe2O4 via in situ polymerization technique

Nanocrystalline Zn_0.5Mn_0.5Fe₂O₄ was synthesized through the pyrolysis of polyacrylate salt precursors prepared via in situ polymerization of the metal salts and acrylic acid. The pyrolysis behavior of the polymeric precursors was studied by use of thermal analysis. The as-obtained product was characterized by powder X-ray diffraction (XRD), transmission electron microscope (TEM), electron diffraction (ED) pattern, scanning electron microscopy (SEM) and electron dispersive X-ray (EDX) analysis. The results revealed that the particle size is in the range of 15–25 nm for Zn-Mn ferrites with good crystallinity. Magnetic properties of the sample at 300 K were measured using a vibrating sample magnetometer, which showed that the sample exhibited characteristics of superparamagnetism.     

Control synthesis of octahedral In2O3 crystals,belts, and nanowires

Octahedral In₂O₃ crystals were synthesized by evaporation of a mixture of In₂O₃ and graphite in a horizontal double-tube system. By adjusting the experimental conditions, In₂O₃ nanowires and nanobelts were also obtained. The microstructures of the resultant In₂O₃ materials were characterized by scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), selected-area electron diffraction (SAED), X-ray diffraction. In addition, the growth mechanism of the octahedral In₂O₃ crystals was discussed in detail.     

Novel photoluminescence properties of InAlO3（ZnO）m superlattice nanowires

One-dimension InAlO 3 (ZnO) m superlattice nanowires were successfully synthesized via chemical vapor deposition.Transmission electron microscopy measurements reveal that the nanowires have a periodic layered structure along the 0001 direction.The photoluminescence properties of InAlO 3 (ZnO) m superlattice nanowires are studied for the first time.The near-band-edge emissions exhibit an obvious red shift due to the formation of the localized tail states.The two peaks centered at 3.348 eV and 3.299 eV indicate a lever phenomenon at the low-temperature region.A new luminescence mechanism is proposed,combined with the special energy band structure of InAlO 3 (ZnO) m.     

SnO2微纳米材料的合成及其生长机理研究

利用简单的化学气相沉积法,以Sn粉为源材料合成不同形貌的一维SnO₂纳米棒、纳米线和纳米花等纳米结构,并通过减小载气中的氧含量获得新颖的SnO₂亚微米环状结构.通过调节Sn粉的量和载气中的氧含量、升温速率等试验条件,有效实现SnO₂一维纳米结构的控制生长.采用扫描电子显微镜、能谱仪和X射线衍射仪表征产物形貌、成分和物相结构,并探讨了SnO₂微纳米材料的生长机理. 关键词： 2')" href="#">SnO₂ 纳米结构 亚微米环 生长机理     

Synthesis, morphologies and Raman-scattering spectra of crystalline stannic oxide nanowires

SnO₂ nanowires were synthesized using a direct gas reaction route and were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), selected-area electron diffraction (SAED), high-resolution transmission electron microscopy (HRTEM) and Raman-scattering spectroscopy. XRD, SEM, SAED and HRTEM indicated that the products were tetragonal SnO₂ nanowires with diameters of 10–50 nm. The nanowires were single crystal and solid inside. Dendritic nanowires were observed for the first time. Three vibrational modes were observed in the Raman spectra of the samples. Received: 7 January 2002 / Accepted: 11 April 2002 / Published online: 19 July 2002     

铂修饰的{001}面暴露的二氧化钛纳米片阵列的制备和光催化性能

采用有机溶剂热法在FTO衬底上制备{001}面暴露的单晶锐钛矿相TiO₂纳米片阵列,通过FESEM和XRD研究样品的形貌和晶体结构. 与水热法制备的纳米片阵列相比,有机溶剂热法制备的样品取向性更好. 采用光沉积方法在纳米片阵列上沉积Pt,所得到的Pt纳米颗粒粒径更为均匀,并且更容易沉积在{001}面上. 所负载的Pt 纳米颗粒增强了TiO₂纳米片的光吸收性能,同时大大减弱了光致发光强度. 在光催化性能测试中,具有最优负载量的样品催化性能提高了一倍. 与传统的Pt负载相比,{001}面的最优负载量显得相当小,这可能源于高活性{001}面的原子结构.     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

径向生长的具有分级结构的四氧化三钴微晶及其在气体传感上的应用

通过在水热合成后追加退火处理,制备了径向生长的具有分级结构的树枝状三维Co₃O₄晶体,并用X射线衍射仪、扫描电子显微镜和透射电子显微镜对其结构和形貌进行了表征. 在110 oC对其气体探测性能的研究表明这种Co₃O₄分级结构对氨气有较高的探测灵敏度和响应速度(10 s),性能稳定并具有可重复性. 同时,还在较低的探测温度下对酒精、丙酮和苯进行了气敏探测.