Thermoelastic problem for a circular cylinder of reinforced multilayer material

The temperature stresses and displacements are determined in an elastic circular cylinder of reinforced multilayer material. The relationship between the displacements of the inside and outside surfaces of the cylinder and the radial stresses and the mechanical and thermophysical properties of the components, the reinforcement ratio, and the ratio of the radii is investigated. The results are used to interpret the behavior of wound glass-reinforced plastic products under varying temperature conditions and during the curing stage.Mekhanika Polimerov, Vol. 3, No. 1, pp. 136–141, 1967     

Results of an experimental investigation of the residual stresses in wound glass-reinforced plastics

The results of an experimental investigation of the residual stresses in wound glass-reinforced plastic rings are presented. The residual stresses were determined by the Davidenkov method. The dependence of the maximum tensile and compressive circumferential stresses on ring thickness and polymerization temperature is investigated. The experimental data are compared with the results of calculations based on the theory proposed in [1, 2].Moscow Power Engineering Institute. Translated from Mekhanika Polimerov, No. 6, pp. 1116–1119, November–December, 1970.     

Effect of the conditions of formation of glued joints on their thermophysical properties

A correlation has been experimentally established between the thermal resistance of adhesive films and the internal stresses that develop during the curing process. During cure the thermal resistance varies in parallel with the internal stresses. It is assumed that the development of thermal resistance is determined by the tension produced in the film by the development of the internal stresses.Voronezh Forest Engineering Institute. Translated from Mekhanika Polimerov, No. 4, pp. 754–756, July–August, 1973.     

Determination of the residual stresses in wound glass-reinforced plastic rings

The stresses that develop during winding in wound glass-reinforced plastic rings change during polymerization, when the modulus of elasticity in the radial direction is reduced by heating. Further changes occur in connection with cooling and removal from the mandrel. The theoretical relations obtained for determining these stresses are found to be confirmed by experiment.Bauman Moscow Higher Technical College. Translated from Mekhanika Polimerov, No. 5, pp. 892–898, September–October, 1969.     

Effect of a uniaxial load on moisture absorption by an epoxy binder

Conclusion The above-developed method of studying the effect of uniaxial compressive and tensile loads on moisture absorption in polymers was tested on epoxy binder EDT-10. It was established experimentally for this material that tensile stresses up to 50 MPa significantly increase the equilibrium moisture content (up to 20% of the initial value). There is a corresponding increase in the rate of moisture absorption during the initial stage of the sorption process — up to 80% of the initial value. No changes in the diffusion coefficient were seen in this case. The application of compressive stresses of up to 40 MPa also had no effect on the kinetics of moisture absorption.Deceased.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 1, pp. 110–115, January–February, 1993.     

Comparison of the temperature stresses in a free and in a constrained cylinder

The conditions under which the radial and peripheral stresses in a free and in a constrained cylinder coincide at the ends of the cylinder when the temperature distribution is axially symmetrical are considered.P. I. Baranov Central Institute for Aircraft Engine Construction, Moscow. Translated from Mekhanika Polimerov, No. 1, pp. 163–165, January–February, 1972.     

Calculation of the residual stresses and strains in wound reinforced-plastic products

A method is proposed for determining the residual stresses and strains in wound glass-reinforced plastic products. The fabrication process is divided into five stages: winding, heating polymerization, cooling, and removal from the mandrel. The initial stresses that develop during winding and the subsequent stress increment associated with heating are taken into account. Polymerization is treated as a process during which the mechanical and thermophysical properties of the material change. Chemical shrinkage of the resin and its filtration through the fiberglass are disregarded. Equations are derived for the residual radial and peripheral stresses in the finished product, for the residual change in inside diameter, and for the temperature at which the product is released from the mandrel during the cooling process. The experimental data relating to two types of wound products are discussed. The results of a computation of the residual stresses and the residual changes in inside diameter are compared with the experimental data.Moscow Power Engineering Institute. Translated from Mekhanika Polimerov, Vol. 5, No. 1, pp. 134–139, January–February, 1969.     

Effect of technological factors on the mechanical reliability of structures made from composites

Research on the effect of technological factors on the strength of reinforced-plastics structures is reviewed. Attention is concentrated on structures in the form of bodies of revolution fabricated by the winding technique. The influence of the winding parameters and the curing regime on the residual stresses is discussed. Data on the variation of the mechanical properties of the resin in the course of the curing process are examined. The contributions of chemical and thermal shrinkage to residual stress formation are compared. Methods of reducing the residual stresses are considered.Presented at the 2nd All-Union Conference on Polymer Mechanics, Riga, November 10–12, 1971.Moscow Power Engineering Institute. Translated from Mekhanika Polimerov, No. 3, pp. 529–540, May–June, 1972.     

The influence of coupled diffusion of heat and moisture on the state of stress in a plate

The fundamental results of previous reports on the coupling of the processes of diffusion of heat and moisture in solids are reviewed. The influence of the coupling on diffusion into an infinite plate from both its surfaces is discussed with the aim of clarifying what can and cannot be learned from such experiments. The nonuniformity of temperature and moisture content tends to cause nonuniform deformation. The stresses set up are computed for a homogeneous, isotropic plate. These self-equilibrating stresses first increase with time and then die out. For some combinations of material constants, the stresses undergo a reversal. For example, in some cases the surface stresses initially become compressive as moisture begins diffusing into the plate. Subsequently, as the interior of the plate increases in temperature due to the coupling effect, the surface stresses become tensile before eventually subsiding to zeroPublished in Mekhanika Kompozitnykh Materialov, No. 1, pp. 53–61, January–February, 1980.     

Determination of the magnitude and distribution of the initial stresses in glass-reinforced plastics

The stresses that develop in the resin at and near the glass-resin interface during the curing of polyester and epoxy glass-reinforced plastics have been experimentally studied by the photoelastic method. The volume state of stress in three mutually perpendicular directions in various sections and in the danger zones is qualitatively and quantiatively described. It is established that the stresses investigated may be the cause of cracking that reduces the tightness and strength of the glass-reinforced plastic.I. M. Gubkin Moscow Institute of the Petrochemical and Gas Industry. Translated from Mekhanika Polimerov, No. 4, pp. 661–667, July–August, 1973.     

Investigation of the temperature residual stresses and strains in thick-walled wound reinforced plastic products

The kinetics of the temperature residual stresses and strains in thick-walled reinforced-plastic cylinders and rings have been experimentally investigated employing a special procedure for continuously monitoring the internal strains and stresses in the various zones of the semifinished product during the heat treatment stage. The effect of the resin polymerization (polycondensation) temperature and the mandrel material on the magnitude and distribution of the temperature stresses is considered. The total residual stresses have been determined by a nondestructive strain-gauge method with differentiation of the components.Translated from Mekhanika Polimerov, No. 6, pp. 1040–1046, November–December, 1971.     

Compensation of thermal stresses in glass-fiber-reinforced plastic articles by the layerwise winding method

The contact pressures which must be created during winding with layerwise hardening in order to compensate radial stresses on the contact surfaces of the layers are determined. The tensions realizing the necessary pressures are calculated. The relations obtained are checked experimentally.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 4, pp. 640–645, July–August, 1972.     

Experimental study of the effect of technological parameters on the residual stresses in thin-walled coiled parts

The effect of the parameters of heat treatment and programmed winding under tension on the residual stresses in thin-walled coiled parts made from glass plastic by the "dry" winding of a heated glass strip on an unheated mandrel is studied experimentally. The effect of the thickness of the parts on the maximum radial residual stresses is considered. A method is proposed for regulating the residual stresses in parts with very thick walls.Translated from Mekhanika Polimerov, No. 1, pp. 75–80, January–February, 1972.     

Residual stresses in glass-reinforced polyethylene

The variation of the axial and radial components of the residual stresses in fiber-reinforced polyethylene with distance from the fiber has been investigated. It is shown that, irrespective of the agent employed, coupling leads to an increase in stresses. The values obtained for the residual stresses are compared with the adhesion strength determined by the shearing method. The effect of a structure-forming agent on the residual stresses is investigated.Mendeleev Moscow Chemical Engineering Institute. Translated from Mekhanika Polimerov, No. 4, pp. 722–724, July–August, 1971.     

Study of the residual (internal) stresses in reinforced epoxy resin

An optical polarization method has been used to study the residual (internal) stresses in reinforced ED-6 epoxy resin cured with maleic anhydride. The effects of "chemical" shrinkage, volume change relaxation during during curing, and the difference linear coefficients of thermal expansion for reinforcement and resin are elucidated. It is shown that adjacent reinforcing elements interact. The stress state is investigated with reference to a model of the elementary cell of the regular structure of a unidirectional glass-reinforced plastic. The residual stresses are found as a function of the resin/reinforcement ratio.Mekhanika Polimerov, Vol. 1, No. 4, pp. 76–80, 1965     

Effect of heat treatment on the distribution of residual stresses and the properties of epoxy polymers

Conclusions The analysis of the experimental data showed that heat treatment results in a reduction in the stressed state of a polymer, which affects the tensile strength of the material to a greater degree than the compressive strength. During heat treatment, significant changes take place in sections of the polymer damaged by the effect of residual compressive stresses and sections in which the residual stresses change sign. The quantitative relations in the change in the tensile strength of the material in these two sections make it possible to explain the mechanism of the effect of heat treatment and to predict its character.Translated from Mekhanika Kompozitnykh Materialov, No. 5, pp. 787–790, September–October, 1986.     

Polymerization stresses in linear viscoelastic media

It is proposed to use a model of the hereditary type to take into account the stresses developing in the process of polymerization. The effect of the degree of polymerization (cure) on the viscoelastic properties of the material is taken into account by introducing a function analogous to the temperature shift function in time-temperature superposition. In this case the system of equations consists of the above-mentioned system of equations of viscoelasticity, the kinetic equation of the curing process, and the equation of heat conduction with allowance for the presence of sources and variable thermophysical characteristics.M. V. Lomonosov Moscow State University. Translated from Mekhanika Polimerov, Vol. 4, No. 4, pp. 716–723, July–August, 1968.     

Anisotropy in the destruction of compact bone material

Conclusions 1. The nature of the destruction of compact bone material upon short-term static compressive and tensile stresses, as well as upon impact bending, is a function of the anistropy of the structure on the osteon level.2. The compact bone material of femoral bones of the age range studied is destroyed by shear for the types of stresses indicated.3. The nature of the destruction of samples of compact bone material for the stresses studied may be generalized for tubular bones.Kurgan Scientific-Research Institute of Experimental and Clinical Orthopedics and Traumatology. Translated from Mekhanika Polimerov, No. 2, pp. 319–324, March–April, 1978.     

Resistance of composite flywheel rim to radial tensile stresses from centrifugal forces based on results of pure bending of a rim segment

A method is proposed for evaluating the resistance of a flywheel rim to radial stresses in free rotation. The method is based on loading a rim segment in pure bending and calculating the limiting moment and the corresponding limiting angular velocity. Applicability of the method is substantiated theoretically by investigating the similarity of the radial stress diagrams in rotation and pure bending. The method is verified experimentally for the strained state of a rim segment in pure bending.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 4, pp. 521–526, July–August, 1993.     

Method of testing polymer monofilaments for compressive deformability in the radial direction

A method and an apparatus for testing polymer monofilaments in short-time and long-time compressive creep in the radial direction are proposed. By this means it is possible to test five specimens simultaneously with indenters of selected shape at a constant givenload.I. M. Gubkin Moscow Institute of the Petrochemical and Gas Industry. Translated from Mekhanika Polimerov, No. 6, pp. 1112–1114, November–December, 1971.