Solvent effects on the adsorption and self-organization of Mn12 on Au(111)

A sulfur-containing single molecule magnet, [Mn12O12(O2CC6H4SCH3)16(H2O)4], was assembled from solution on a Au(111) surface affording both submonolayer and monolayer coverages. The adsorbate morphology and the degree of coverage were inspected by scanning tunneling microscopy (STM), while X-ray photoelectron spectroscopy (XPS) allowed the determination of the chemical nature of the adsorbate on a qualitative and quantitative basis. The properties of the adsorbates were found to be strongly dependent on the solvent used to dissolve the magnetic complex. In particular, systems prepared from tetrahydrofuran solutions gave arrays of isolated and partially ordered clusters on the gold substrate, while samples prepared from dichloromethane exhibited a homogeneous monolayer coverage of the whole Au(111) surface. These findings are relevant to the optimization of magnetic addressing of single molecule magnets on surfaces.     

Bonding and structure of glycine on ordered Al2O3 film surfaces

The interaction between glycine (NH2CH2COOH) layers and an ultrathin Al2O3 film grown epitaxially onto NiAl(110) was studied by temperature-programmed desorption, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, work function measurements, and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. At monolayer coverages at 110 K, there are two coexisting molecular forms: the anionic (NH2CH2COO-) and the zwitterionic form (NH3+CH2COO-) of glycine. As deduced from the photoemission data, the buildup of multilayers at 110 K leads to a condensed phase predominantly in the zwitterionic state. In contrast to the monolayer at 110 K, the monolayer formed at 300 K consists primarily of glycine molecules in the anionic state. The latter species is adsorbed with the oxygen atoms of the carboxylic group pointing toward the substrate. The polarization-dependent C K- and O K-edge NEXAFS spectra indicate that the glycinate species in the monolayer at 300 K is oriented nearly perpendicular to the surface, with the amino group pointing away from the surface.     

Suppression of electron-transfer characteristics of ferrocene by OTS monolayer on a silicon/electrolyte interface

The passivating behavior of self-assembled monolayers (SAMs) of octadecyltrichlorosilane (OTS) on an n-type Si(100) electrode with and without a redox species like ferrocene in a polar non-aqueous medium has been investigated using techniques like contact angle measurements, Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) to understand the role of the monolayer. The electron-transfer behavior of ferrocene is found to be drastically affected by the presence of monolayer and the reasons for these are analyzed as a function of the change in resistance, dielectric thickness and coverage of the monolayer. Electrochemical impedance analysis in the presence of ferrocene gives the monolayer coverage as 0.998 and the apparent rate constant calculated from this gives 4.85 x 10(-12) cm s(-1) in comparison with 4.4 x 10(-8) cm s(-1) for a similar electrode without any monolayer. A positive shift of 200 mV in the flat-band potential after monolayer formation also suggests the covalent coupling of the silane monolayer offering a protective barrier.     

Probing the electronic properties of dichromium oxide clusters Cr2On- (n=1-7) using photoelectron spectroscopy

In an effort to elucidate the variation of the electronic structure as a function of oxidation and composition, we investigated an extensive series of dichromium oxide clusters, Cr2On- (n=1-7), using photoelectron spectroscopy (PES). Well-resolved PES spectra were obtained at several photon energies. While low photon energy spectra yielded much better spectral resolution, high photon energy data allowed both Cr 3d- and O 2p-derived detachment features to be observed. The overall spectral evolution of Cr2On- exhibits a behavior of sequential oxidation with increasing oxygen content, where low binding energy Cr 3d-based spectral features diminish in numbers and the spectra shift towards higher binding energies as a result of charge transfer from Cr to O. Evidence was obtained for the population of low-lying isomers for Cr2O2-, Cr2O3-, and Cr2O6-. The current data are compared with previous studies and with related studies on W2On- and Mo2On-.     

纳米晶镍-钼合金电沉积层的结构与性能

研究了Ｃｒ２Ｏ３、ＭｏＯ３、ＳＯ２－４和ＣｕＳＯ４在ＳｎＯ２表面的单层分散及其对ＳｎＯ２超细粉热稳定性的影响．结果表明,几种化合物在ＳｎＯ２上均能单层分散且分散阈值都接近按密置单层模型估算的分散容量极限值;表面单层覆盖能十分有效地抑制ＳｎＯ２的高温烧结,单层覆盖率与经５００℃焙烧后样品中ＳｎＯ２的粒径和比表面有很好的对应关系,表现出很强的阈值效应;单层覆盖率达到一定程度,ＳｎＯ２高温烧结便可基本得到抑制．     

Interfacial oxidation of ultrathin nickel and chromium films on yttria-stabilized zirconia

The substrate-induced oxidation upon prolonged annealing in UHV of ultrathin films of Ni and Cr vapor deposited on yttria-stabilized zirconia YSZ(100) was studied by X-ray photoelectron spectroscopy (XPS) to obtain information about the oxidation mechanism, determine the available quantity of reactive oxygen in YSZ, and investigate the thermal stability of the thin oxide films. Up to about 0.8 ML of Ni deposited at room temperature was oxidized to NiO at a constant rate at 650 K via the substrate, whereas at slightly higher coverage, the oxidation rate under identical conditions was drastically reduced. In contrast to Ni, up to 4.8 ML of Cr deposited at 275 K could be oxidized via the substrate to Cr2O3 upon extensive UHV annealing at increasing temperature up to 820 K, indicating a reactive oxygen content of at least 4 x 10(-6) with respect to the lattice oxygen in the YSZ specimen. The Cr2O3 decomposed to metallic Cr above about 800 K, whereas NiO was stable up to the maximum temperature of 875 K. These results indicate that the oxidation via the substrate is kinetically analogous to the gas-phase oxidation of bulk Ni and Cr. The reactive oxygen content of the single-crystal YSZ is larger than expected, and part of it is accommodated at the surface of the substrate. The thermal stability of the thin oxide films is determined by the oxygen exchange with YSZ and not by the respective bulk oxide thermodynamic decomposition temperature.     

Atomic imaging of nucleation of trimethylaluminum on clean and H2O functionalized Ge(100) surfaces

The direct reaction of trimethylaluminum (TMA) on a Ge(100) surface and the effects of monolayer H(2)O pre-dosing were investigated using ultrahigh vacuum techniques, such as scanning tunneling microscopy (STM), scanning tunneling spectroscopy (STS), and x-ray photoelectron spectroscopy (XPS), and density functional theory (DFT). At room temperature (RT), a saturation TMA dose produced 0.8 monolayers (ML) of semi-ordered species on a Ge(100) surface due to the dissociative chemisorption of TMA. STS confirmed the chemisorption of TMA passivated the bandgap states due to dangling bonds. By annealing the TMA-dosed Ge surface, the STM observed coverage of TMA sites decreased to 0.4 ML at 250?°C, and to 0.15 ML at 450?°C. XPS analysis showed that only carbon content was reduced during annealing, while the Al coverage was maintained at 0.15 ML, consistent with the desorption of methyl (-CH(3)) groups from the TMA adsorbates. Conversely, saturation TMA dosing at RT on the monolayer H(2)O pre-dosed Ge(100) surface followed by annealing at 200?°C formed a layer of Ge-O-Al bonds with an Al coverage a factor of two greater than the TMA only dosed Ge(100), consistent with Ge-OH activation of TMA chemisorption and Ge-H blocking of CH(3) chemisorption. The DFT shows that the reaction of TMA has lower activation energy and is more exothermic on Ge-OH than Ge-H sites. It is proposed that the H(2)O pre-dosing enhances the concentration of adsorbed Al and forms thermally stable Ge-O-Al bonds along the Ge dimer row which could serve as a nearly ideal atomic layer deposition nucleation layer on Ge(100) surface.     

V2O5／TiO2催化剂的表面结构和酸碱性及氧化还原性

 研究了一系列锐钛矿担载的钒氧化物催化剂的表面性质．X射线衍射和Raman光谱表明，8％V2O5／TiO2催化剂上的V2O5处于单层分散状态．程序升温还原研究表明，单层分散的钒物种较易被还原，而形成多聚态和晶态后钒物种的还原温度升高．NH3吸附量热结果表明，在钒物种达到单层分散前，催化剂的表面酸性随钒担载量的增加而减弱，超过单层分散后，表面酸位的数目和强度基本不变．异丙醇脱氢／脱水反应结果表明，有O2时V2O5／TiO2催化剂显示出很强的氧化还原性，无O2时催化剂的脱水选择性较高．通过异丙醇的脱氢／脱水反应，将V2O5／TiO2催化剂的表面结构与其酸碱性和氧化还原性进行了初步的关联．     

Thermal behavior of perfluoroalkylsiloxane monolayers on the oxidized Si(100) surface

The thermal stability of perfluoralkylsiloxane monolayers in a vacuum is investigated via X-ray photoelectron spectroscopy (XPS) for temperatures up to 600 degrees C. 1H,1H,2H,2H,-perfluorodecyltrichlorosilane (FDTS) monolayers are deposited on oxidized Si(100) surfaces from the vapor phase with various degrees of surface coverage. Significant monolayer desorption is observed to occur at temperatures below 300 degrees C regardless of the initial monolayer coverage. The desorption mechanism follows first-order kinetics and is independent of the initial coverage. Removal of FDTS is found to occur by the loss of the entire molecular chain, as evidenced by the fact that the CF(3)/CF(2) peak area ratios remain unaffected by the annealing process although CF(n)()/Si peak ratio declines with annealing. This is in sharp contrast to the behavior observed for octadecyltrichlorosilane monolayer for which elevated temperature leads to C-C bond breakage and successive shortening of the alkyl chain. It is also shown that the binding energy and the shape of the F 1s line are good indicators of the degree of disorder in the chain, as well as a measure of the interaction of the chain with the silicon surface.     

Oxidation of alkylsilane-based monolayers on gold

The oxidation of alkylsilane monolayers on Au has been studied by X-ray photoelectron spectroscopy, reflection-absorption infrared spectroscopy, contact-angle measurements, and scanning tunneling microscopy. Exposure of the monolayers at 298 K to pure O(2) or H(2)O (>5 x 10(-5) Torr and >150 000 L) does not cause oxidation. Ambient atmosphere only causes oxidation if direct sight lines are maintained to the sample. Ozone exposure results in rapid monolayer oxidation. Oxidation initially occurs only at the Si atom, resulting in formation of a cross-linked siloxane monolayer that retains alkyl surface termination. Prolonged ozone exposures result in the oxidation and subsequent loss of the alkyl chain.     

Photophysical and photocatalytic properties of SrTiO3 doped with Cr cations on different sites

Usually, SrTiO3 monodoped with Cr cations at the Ti4+ site hardly shows visible light photocatalytic activity. Revealing the origin of this issue is important for us to find an alternative approach to make SrTiO3 active under visible light irradiation. In this paper, two Cr-doped SrTiO3-(Sr0.95Cr0.05)TiO3 and Sr(Ti0.95Cr0.05)O3-were synthesized by a conventional solid-state reaction method, and their photophysical and photocatalytic properties were studied comparatively. It was found that both (Sr0.95Cr0.05)TiO3 and Sr(Ti0.95Cr0.05)O3 showed considerable absorption to visible light. However, their photocatalytic activities for H2 evolution from aqueous methanol solution under visible light irradiation were significantly different: the H2 evolution rate over (Sr0.95Cr0.05)TiO3 (approximately 21 micromol/h) was more than 100 times that over Sr(Ti0.95Cr0.05)O3 (approximately 0.2 micromol/h). X-ray photoelectron spectroscopy analysis results revealed that the Cr cations doped at the Sr2+ site were all trivalent state (Cr3+), while those doped at the Ti4+ site were mixed valent states (Cr3+ and Cr6+). The different photocatalytic activities of H2 evolution are supposed to closely relate to the different valent states of Cr doped at different sites (Sr2+ or Ti4+) in SrTiO3. Possible electronic structures of (Sr0.95Cr0.05)TiO3 and Sr(Ti0.95Cr0.05)O3 were proposed in relation to their photophysical and photocatalytic properties.     

Low-cost synthesis of flowerlike α-Fe2O3 nanostructures for heavy metal ion removal: adsorption property and mechanism

Flowerlike α-Fe(2)O(3) nanostructures were synthesized via a template-free microwave-assisted solvothermal method. All chemicals used were low-cost compounds and environmentally benign. These flowerlike α-Fe(2)O(3) nanostructures had high surface area and abundant hydroxyl on their surface. When tested as an adsorbent for arsenic and chromium removal, the flowerlike α-Fe(2)O(3) nanostructures showed excellent adsorption properties. The adsorption mechanism for As(V) and Cr(VI) onto flowerlike α-Fe(2)O(3) nanostructures was elucidated by X-ray photoelectron spectroscopy and synchrotron-based X-ray absorption near edge structure analysis. The results suggested that ion exchange between surface hydroxyl groups and As(V) or Cr(VI) species was accounted for by the adsorption. With maximum capacities of 51 and 30 mg g(-1) for As(V) and Cr(VI), respectively, these low-cost flowerlike α-Fe(2)O(3) nanostructures are an attractive adsorbent for the removal of As(V) and Cr(VI) from water.     

Localized surface plasmon resonance nanosensor: a high-resolution distance-dependence study using atomic layer deposition

Atomic layer deposition (ALD) is used to deposit 1-600 monolayers of Al(2)O(3) on Ag nanotriangles fabricated by nanosphere lithography (NSL). Each monolayer of Al(2)O(3) has a thickness of 1.1 A. It is demonstrated that the localized surface plasmon resonance (LSPR) nanosensor can detect Al(2)O(3) film growth with atomic spatial resolution normal to the nanoparticle surface. This is approximately 10 times greater spatial resolution than that in our previous long-range distance-dependence study using multilayer self-assembled monolayer shells. The use of ALD enables the study of both the long- and short-range distance dependence of the LSPR nanosensor in a single unified experiment. Ag nanoparticles with fixed in-plane widths and decreasing heights yield larger sensing distances. X-ray photoelectron spectroscopy, variable angle spectroscopic ellipsometry, and quartz crystal microbalance measurements are used to study the growth mechanism. It is proposed that the growth of Al(2)O(3) is initiated by the decomposition of trimethylaluminum on Ag. Semiquantitative theoretical calculations were compared with the experimental results and yield excellent agreement.     

Cr掺杂ZnO(10(¯1)0)表面的原子结构和电子性质研究

多相催化中ZnO基催化剂广泛应用于甲醇合成、水汽变换和合成气转化等诸多领域.近期发展的ZnCrOx-分子筛双功能催化剂(OX-ZEO)打破了传统合成气转化的ASF分布,能够高选择性地实现CO加氢转化为低碳烯烃.其中CO在ZnCrOx表面活化被认为是OX-ZEO催化的关键基元过程,但是ZnCrOx表面的活性位组成和结构目...     

Epitaxial growth of single-crystalline Al(2)O(3) films on Cr(2)O(3)(0001)

Thin, crystallographically oriented single-crystalline Al2O3 films can be grown epitaxially on Cr2O3(0001) by codeposition of Al vapor and O2 at a substrate temperature of 825 K. The properties and growth of these films were monitored by Auger electron spectroscopy (AES), low-energy electron diffraction (LEED), low-energy ion scattering (LEIS), and X-ray photoelectron spectroscopy (XPS). Two routes of preparation were investigated: (i) stepwise growth by alternating deposition of Al at room temperature and subsequent exposure to O2 at elevated temperatures; (ii) codeposition of Al and O2 at T > 800 K. The first route was consistently found to result in the growth of a complex interfacial oxide followed by the growth of polycrystalline Al2O3. The second mode of preparation provided homogeneous and ordered, probably (0001)-oriented, films of Al2O3 that maintained a LEED pattern up to a thickness around 10 A. The surface sensitive Cr MVV Auger transition at 34 eV was completely attenuated once the Al2O3 layer had reached a thickness of 6 A, pointing to film homogeneity at an early stage. This was confirmed by the absence of a significant Cr signal in LEIS spectra.     

Well-ordered self-assembled monolayers created via vapor-phase reactions on a monolayer template

The reaction of vapor-phase alkyl isocyanates (O=C=N-(CH2)n-1CH3) with OH-terminated alkanethiol template monolayers on Au produces well-organized self-assembled monolayers, containing intrachain carbamate linkages (Au/S(CH2)16O(C=O)NH(CH2)n-1CH3, where n = 1-8, 11, and 12). X-ray photoelectron spectroscopy, contact angle goniometry, and reflection absorption infrared spectroscopy suggest that the template surface completely reacts with the isocyanates yielding a monolayer that contains an interchain hydrogen-bonded carbamate network. Spectroscopic data indicates that the alkyl underlayer remains well ordered following reaction with the isocyanates. The order of the overlayer and the hydrogen-bonding interactions between adjacent chains increase as a function of the alkyl isocyanate chain length, n. The overlayer appears to be well ordered for n > or = 5.     

Growth and analysis of octadecylsiloxane monolayers on Al2O3 (0001)

On solvent-cleaned and piranha-etched single-crystal Al2O3(0001) surfaces, uniform, robust, self-assembled monolayers of octadecylsiloxane (ODS) are formed by 48 h exposure to a solution containing octadecyltrichlorosilane (OTS) in an anhydrous atmosphere. X-ray photoelectron spectroscopy, atomic force microscopy, ellipsometry, and water contact angle measurements confirm the presence of a uniform, complete monolayer. Reducing the exposure time or omitting the piranha-etch leads to much less uniform coverage. The ODS monolayers are stable when stored in ambient atmospheres for month-long periods. Thermal desorption in a vacuum environment (10(-9) Torr) shows the ODS monolayer is thermally stable up to at least 420 K. When heated in 200 mTorr of flowing forming gas (N2-10% H2) for 1 h at 520 K, slow loss of ODS was indicated. A schematic model is proposed which involves island nucleation by covalent bonding of OTS to surface hydroxyl groups followed by growth through the addition of mobile ODS species.     

Electronic structure study by means of x-ray spectroscopy and theoretical calculations of the "ferric star" single molecule magnet

The electronic structure of the single molecule magnet system {M[Fe(L(1))(2)](3)}4CHCl(3) [M=Fe,Cr;L(1)=CH(3)N(CH(2)CH(2)O)(2) (2-)] has been studied using x-ray photoelectron spectroscopy, x-ray-absorption spectroscopy, soft-x-ray emission spectroscopy, as well as theoretical density-functional-based methods. There is a good agreement between theoretical calculations and experimental data. The valence band mainly consists of three bands between 2 and 30 eV. Both theory and experiments show that the top of the valence band is dominated by the hybridization between Fe 3d and O 2p bands. From the shape of the Fe 2p spectra it is argued that Fe in the molecule is most likely in the 2+ charge state. Its neighboring atoms (O,N) exhibit a magnetic polarization yielding effective spin S=52 per iron atom, giving a high-spin state molecule with a total S=5 effective spin for the case of M=Fe.     

Kinetics of the CO oxidation reaction on Pt(111) studied by in situ high-resolution x-ray photoelectron spectroscopy

High-resolution x-ray photoelectron spectroscopy has been used to study the kinetics of the CO oxidation reaction on a Pt(111) surface in situ. The study focuses on the interaction of a preadsorbed p(2x2) layer of atomic oxygen with CO dosed using a supersonic molecular beam. Measurements of O 1s and C 1s spectra at 120 K show that CO adsorbs on the oxygen precovered substrate, but no reaction occurs. A maximum CO coverage of 0.23 ML (monolayer) is observed, with CO exclusively bound on on-top sites. In accordance with the literature, bridge sites are blocked by the presence of atomic oxygen. The reaction of CO with preadsorbed O to CO(2) is studied isothermally in a temperature range between 275 and 305 K. The reaction rate initially increases with CO pressure, but saturates at 9x10(-7) mbar. The data indicate that a certain amount of disordered oxygen within the p(2x2) layer acts as a starting point of the reaction and for a given temperature reacts with a higher rate than O in the well-ordered oxygen p(2x2) phase. For the reaction of CO with this ordered phase, the results confirm the assumption of a reaction mechanism, which is restricted to the edges of compact oxygen islands. The activation energy of the reaction is determined to (0.53+/-0.04) eV, with a prefactor of 4.7x10(6+/-0.7) s(-1).     

NO2 adsorption on BaO/Al2O3: the nature of nitrate species

Temperature programmed desorption, infrared spectroscopy, and (15)N solid state NMR spectroscopy were used to characterize the nature of the nitrate species formed on Al(2)O(3) and BaO/Al(2)O(3) NO(x) storage/reduction materials. Two distinctly different nitrate species were found: surface nitrates that are associated with a monolayer BaO on the alumina support, and a bulk-like nitrate that forms on this thin BaO layer. The surface nitrates desorb as NO(2) at lower temperatures than do the bulk-like nitrates, which decompose as NO+O(2) at higher temperatures. The amount of NO(x) stored in the monolayer nitrate is proportional to the surface area of the catalyst, while that in the bulk nitrate increases with BaO coverage.