Adsorption of cationic starch on cellulose studied by QCM-D

The adsorption of cationic starch (CS) from aqueous electrolyte solutions onto model cellulose film has been investigated by the quartz crystal microbalance with dissipation monitoring (QCM-D) and X-ray photoelectron spectroscopy (XPS). The influence of the electrolyte composition and charge density of CS was examined. The adsorption of CS onto cellulose followed the general trends expected for polyelectrolyte adsorption on oppositely charged surfaces, with some exceptions. Thus, as result of the very low surface charge density of the cellulose surface, highly charged CS did not adsorb in a flat conformation even at low ionic strength. The porosity of the film, however, enabled the penetration of coiled CS molecules into the film at high electrolyte concentrations. Differences between the adsorption behavior of CS on cellulose and earlier observations of the adsorption of the same starches on silica could be explained by the different morphologies and acidities of the hydroxyl groups on the two surfaces.     

Adsorption and viscoelastic properties of cationic xylan on cellulose film using QCM-D

The adsorption and viscoelastic properties of cationic xylan layers adsorbed from an aqueous electrolyte solution (NaCl 0, 1, 10, 100 mM) on a cellulose model surface were studied using quartz crystal microbalance with dissipation (QCM-D). Three cationic xylans with different charge densities were used (molecular weight, 9,600 g/mol with degrees of substitution, DS = 0.150, 0.191, and 0.259). The influences of the electrolyte concentration and charge density of cationic xylan on its adsorption onto a cellulose surface were investigated. Low charged cationic xylan was substantially more efficient in surface adsorption on cellulose compared to high charged cationic xylan at a low concentration of electrolytes. Adsorption of low charged cationic xylan decreased with increases in electrolyte concentration. However, adsorption of high cationic xylan increased with electrolyte concentration. The conformation and viscoelastic properties of the layers were interpreted by modeling the data under the assumption that the layers can be explained by the a Voigt model. Low charged cationic xylan adsorbed relatively weakly onto the cellulose surface, and formed a thicker, softer layer than high charged cationic xylan. On the other hand, high charged cationic xylan formed a thinner adsorption layer onto the cellulose surface.     

Quartz crystal microbalance with dissipation monitoring and surface plasmon resonance studies of carboxymethyl cellulose adsorption onto regenerated cellulose surfaces

Adsorption of anionic polyelectrolytes, sodium salts of carboxymethyl celluloses (CMCs) with different degrees of substitution (DS = 0.9 and 1.2), from aqueous electrolyte solutions onto regenerated cellulose surfaces was studied using quartz crystal microbalance with dissipation monitoring (QCM-D) and surface plasmon resonance (SPR) experiments. The influence of both calcium chloride (CaCl(2)) and sodium chloride (NaCl) on CMC adsorption was examined. The QCM-D results demonstrated that CaCl(2) (divalent cation) caused significantly greater CMC adsorption onto regenerated cellulose surfaces than NaCl (monovalent cation) at the same ionic strength. The CMC layers adsorbed onto regenerated cellulose surfaces from CaCl(2) solutions exhibited greater stability upon exposure to flowing water than layers adsorbed from NaCl solutions. Both QCM-D and SPR results showed that CMC adsorption onto regenerated cellulose surfaces from CaCl(2) solutions increased with increasing CaCl(2) concentration up to the solubility limit (10 mM). Voigt-based viscoelastic modeling of the QCM-D data indicated that the CMC layers adsorbed onto regenerated cellulose surfaces had shear viscosities of η(f) ≈ 10(-3) N·s·m(-2) and elastic shear moduli of μ(f) ≈ 10(5) N·m(-2). Furthermore, the combination of SPR spectroscopy and QCM-D showed that the CMC layers contained 90-95% water. Adsorption isotherms for CMCs in CaCl(2) solutions were also obtained from QCM-D and were fit by Freundlich isotherms. This study demonstrated that CMC adsorption from CaCl(2) solutions is useful for the modification of cellulose surfaces.     

Effect of introduced charge in cellulose gels on surface interactions and the adsorption of highly charged cationic polyelectrolytes

The interaction between cellulose surfaces in aqueous solution has been measured using colloidal probe microscopy. Cellulose thin films with varying charge through carboxyl group substitution were used in this study with the surface forces fit to DLVO theory. It was found that the surface potential increased, as expected, with increasing carboxyl substitution. Furthermore, for a given degree of substitution, the surface potential increased as a function of increasing pH. At low pH, the surface forces interaction were attractive and could be fit to the non-retarded Hamaker equation using a constant of 3 x 10(-21) J. At pH greater than 5, the force interactions were monotonically repulsive, regardless of the ionic strength of the solution for all charge densities of the cellulose thin films. The adsorption of polyDADMAC to these charged cellulose films was also investigated using the quartz crystal microbalance. It was found that for the low charge film, a low surface excess of PDADMAC was sensed and that the adsorbed conformation was essentially flat. However for the higher charged cellulose film, a spontaneous de-swelling was observed resulting in no possibility of quantitatively determining the sensed mass using QCM.     

Adsorption of polyelectrolyte multilayers and complexes on silica and cellulose surfaces studied by QCM-D

The adsorption of polyelectrolyte (PE) multilayers and complexes, obtained from both high- and low-charge polyelectrolytes, was studied on silica and on cellulose model surfaces by quartz crystal microbalance with dissipation (QCM-D). The film properties acquired with the different strategies were compared. When polyelectrolytes were added on an oppositely charged surface in sequence to form multilayers both the change in frequency and dissipation increased. The changes in frequency and dissipation were clearly higher if low-charge PEs were used in the multilayer formation. The substrate, silica or cellulose, did not affect the adsorption behaviour of low-charge PEs and only minor differences were seen in the adsorbed amounts and changes in dissipation of high-charge PEs between SiO₂ and cellulose. The complexes formed by low-charge PEs had higher changes in frequency and dissipation at low ionic strength on both surfaces, while the complexes formed from high-charge polyelectrolytes adsorbed more at high salt concentration. The complexes of low-charge polyelectrolytes adsorbed more on silica, while the complexes formed by high-charge PEs formed thicker layers on cellulose. The charge ratio had a significant effect on the adsorption and the highest changes in frequency and dissipation were obtained in the anionic/cationic charge ratio of 0.5–0.6. Generally, the multilayers and complexes formed by low-charge polyacrylamides adsorbed highly and formed rather thick layers on both surfaces, unlike the high-charge PEs which formed thin layers using either one of the addition techniques.     

Tuning the architecture of cellulose nanocrystal-poly(allylamine hydrochloride) multilayered thin films: influence of dipping parameters

Multilayered thin films consisting of alternating cationic polyelectrolyte, poly(allylamine hydrochloride) (PAH), and anionic cellulose nanocrystals (CNs) were constructed using the dipping procedure by screening different experimental parameters: the drying step between each layer adsorption, the dipping time, the ionic strength of the PAH solution, and the concentration of CNs dispersion. We showed that the drying process and the ionic strength of PAH solution were crucial parameters for the successful construction of 8-bilayer films. Film thickness is mainly influenced by dipping time and CN concentration when using the dipping procedure without drying. Two architectures of adsorbed CN layers-a single or a double layer of CNs-were revealed on the basis of the thickness increment per bilayer, depending on experimental conditions. The layer adsorption process was investigated in real-time using quartz crystal microbalance with dissipation (QCM-D) experiments in an aqueous environment or by incorporating a drying step. On the basis of in situ construction of PAH-CN films in wet media, QCM-D data were indicative of highly hydrated films for which the progressive layer stacking is disturbed or prevented. QCM-D monitoring of CNs and PAH layer adsorption was monitored by incorporating a drying process. The impact of experimental parameters on PAH-CN multilayered construction and on CN layer configuration is discussed. This study offers new opportunities for tailoring the architecture of CN-based multilayer films.     

Adsorption of bacteria and polycations on model surfaces of cellulose, hemicellulose and wood extractives studied by QCM-D

Quartz crystal microbalance with dissipation monitoring (QCM-D), atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM) were used as the tools to study the adsorption of bacteria onto surfaces of silica and polystyrene coated with materials related to papermaking. Cationic polyelectrolytes used as fixatives and retention aids in paper industry were found to promote irreversible adsorption of the ubiquitous white water bacterium, Pseudoxanthomonas taiwanensis, onto model surfaces of cellulose (pH 8). The high charged low molecular weight polyelectrolyte, poly(diallyldimethyl) ammonium chloride (pDADMAC) adsorbed to silica surface as a flat and rigid layer, whereas the low charged cationic polyacryl amide (C-PAM) of high molecular weight adsorbed as a thick and loose layer. AFM images showed that the polyelectrolytes accumulated as layers around each bacterial cell. In the presence of wood hemicellulose (O-acetyl-galactoglucomannan) the bacteria adsorbed massively, as large, tightly packed rafts (up to 0.05mm in size) onto the polystyrene crystal surface coated with wood extractives (pH 4.7). AFM and FESEM micrographs also showed large naked areas (with no bacteria) in between the bacterial rafts on the crystal surface. In this case, QCM-D only incompletely responded to the massiveness of the bacterial adsorption. The results indicate that cationic polymers can be used to increase the retention of bacteria from the process water onto the fibre web and that, depending on the balance between hemicelluloses and wood extractives and pH of the process waters, bacteria can be drawn from process waters onto surfaces.     

Adsorption of carboxymethyl cellulose on polymer surfaces: evidence of a specific interaction with cellulose

The adsorption of carboxymethyl cellulose (CMC), one of the most important cellulose derivatives, is crucial for many scientific investigations and industrial applications. Especially for surface modifications and functionalization of materials, the polymer is of interest. The adsorption properties of CMC are dependent not only on the solutions state, which can be influenced by the pH, temperature, and electrolyte concentration, but also on the chemical composition of the adsorbents. We therefore performed basic investigation studies on the interaction of CMC with a variety of polymer films. Thin films of cellulose, cellulose acetate, deacetylated cellulose acetate, polyethylene terephthalate, and cyclo olefin polymer were therefore prepared on sensors of a QCM-D (quartz crystal microbalance) and on silicon substrates. The films were characterized with respect to the thickness, wettability, and chemical composition. Subsequently, the interaction and deposition of CMC in a range of pH values without additional electrolyte were measured with the QCM-D method. A comparison of the QCM-D results showed that CMC is favorably deposited on pure cellulose films and deacetylated cellulose acetate at low pH values. Other hydrophilic surfaces such as silicon dioxide or polyvinyl alcohol coated surfaces did not adsorb CMC to a significant extent. Atomic force microcopy confirmed that the morphology of the adsorbed CMC layers differed depending on the substrate. On hydrophobic polymer films, CMC was deposited in the form of larger particles in lower amounts whereas hydrophilic cellulose substrates were to a high extent uniformly covered by adsorbed CMC. The chemical similarity of the CMC backbone seems to favor the irreversible adsorption of CMC when the molecule is almost uncharged at low pH values. A selectivity of the cellulose CMC interaction can therefore be assumed. All CMC treated polymer films exhibited an increased hydrophilicity, which confirmed their modification with the functional molecule.     

Adsorption of plasmid DNA to a natural organic matter-coated silica surface: kinetics, conformation, and reversibility

A quartz crystal microbalance with dissipation (QCM-D) has been used to determine the adsorption rate of ampicillin-resistant linear and supercoiled plasmid DNA onto a silica surface coated with natural organic matter (NOM). The structure of the resulting adsorbed DNA layer was determined by analyzing the viscoelastic properties of the adsorbed DNA layers as they formed and were then exposed to solutions of different ionic composition. The QCM-D data were complemented by dynamic light scattering measurements of diffusion coefficients of the DNA molecules as a function of solution ionic composition. The obtained results suggest that electrostatic interactions control the adsorption and structural changes of the adsorbed plasmid DNA on the NOM-coated silica surface. The adsorption of DNA molecules to the NOM layer took place at moderately high monovalent (sodium) electrolyte concentrations. A sharp decrease in solution ionic strength did not result in the release of the adsorbed DNA, indicating that DNA adsorption on the NOM-coated silica surface is irreversible under the studied solution conditions. However, the decrease in electrolyte concentration influenced the structure of the adsorbed layer, causing the adsorbed DNA to adopt a less compact conformation. The linear and supercoiled DNA had similar adsorption rates, but the linear DNA formed a thicker and less compact adsorbed layer than the supercoiled DNA.     

All-cellulose multilayers: long nanofibrils assembled with short nanocrystals

Self-organized multilayer films were formed by sequential addition of oppositely charged cellulose I nanoparticles. The all-cellulosic multilayers were prepared via adsorption of cationicially modified cellulose nanofibrils (cat NFC) and anionic short crystalline cellulose (CNC) at pH 4.5 and pH 8.3. The properties and build-up behavior of layer-by-layer-constructed films were studied with microgravimetry (QCM-D) and the direct surface forces in these systems were explored with colloidal probe microscopy to gain information about the fundamental interplay between cat NFC and anionic CNC. The importance of the first layer on the adsorption of the consecutive layers was demonstrated by comparing pure in situ adsorption in the QCM-D with multilayer films made by spin coating the first cationic NFC layer and then subsequently adsorbing the following layers in situ in the QCM-D chamber. Differences in adsorbed amount and viscoelastic behavior were observed between those two systems. In addition, a significant pH dependence of cat NFC charge was found for both direct surface interactions and layer properties. Moreover the underlying cellulose layer in multilayer film was established to influence the surface forces especially at lower pH, where the cat NFC chains extensions were facilitated and overall charge was affected by the cationic counterpart within the layers. This enhanced understanding the effect of charge and structure on the interaction between these renewable nanoparticles is valuable when designing novel materials based on nanocellulose.     

Interaction of the anionic surfactant SDS with a cellulose thin film and the role of electrolyte and poyelectrolyte. 2 Hydrophilic cellulose

The interaction of the anionic surfactant, sodium dodecylsulfate (SDS), with the hydrophilic surface of a thin cellulose film and the role of electrolyte (0.1 M NaCl) and the polyelectrolyte, poly(dimethyldiallyl ammonium chloride) [polydmdaac], have been studied by neutron reflectivity (NR). The thin cellulose films were prepared by Langmuir-Blodgett (LB) deposition of trimethylsilyl-cellulose (TMSC) on silicon, and the hydrophilic surface was produced by the cleaving of the terminal methyl groups of the TMSC by HCl vapor. Despite both the surfactant and cellulose surfaces being nominally anionic, SDS adsorption and swelling of the cellulose film occurred during adsorption. The results show that the nature of the adsorption and the extent of the penetration into the cellulose film can be controlled by the addition of electrolyte, NaCl, and cationic polyelectrolyte, polydmdaac.     

Lignin adsorption on cellulose fibre surfaces: Effect on surface chemistry, surface morphology and paper strength

The adsorption of lignin on cellulose fibres at neutral pH and the effects of calcium ions and a cationic polyelectrolyte (PDADMAC) on the adsorption have been studied. The surface coverage by lignin was determined by electron spectroscopy for chemical analysis (ESCA). The morphology of the lignin layer was studied by atomic force microscopy (AFM). The effect of adsorbed polyelectrolyte and lignin on the strength properties of the paper was also studied. The adsorbed amount of lignin increased monotonically with lignin concentration. Addition of calcium ions resulted in a very high surface coverage by lignin. PDADMAC did not enhance the adsorption of lignin, but without addition of polyelectrolyte the lignin was very weakly attached to the fibre surface. PDADMAC formed complexes with lignin in solution. At high polymer/lignin concentration ratios the charge of the complex was positive and it adsorbed irreversibly as large blobs. At low ratios the complex was easily washed away from the fibre surface. When PDADMAC was pre-adsorbed on the fibre surface the lignin adsorbed as small granules at all lignin concentrations. Neither PDADMAC nor lignin alone increased the strength of pulp sheets significantly. However, together they increased the bonding between fibres.     

Smooth model surfaces from lignin derivatives. II. Adsorption of polyelectrolytes and PECs monitored by QCM-D

For the first time to the knowledge of the authors, well-defined and stable lignin model surfaces have been utilized as substrates in polyelectrolyte adsorption studies. The adsorption of polyallylamine (PAH), poly(acrylic acid) (PAA), and polyelectrolyte complexes (PECs) was monitored using quartz crystal microgravimetry with dissipation (QCM-D). The PECs were prepared by mixing PAH and PAA at different ratios and sequences, creating both cationic and anionic PECs with different charge levels. The adsorption experiments were performed in 1 and 10 mM sodium chloride solutions at pH 5 and 7.5. The highest adsorption of PAH and cationic PECs was found at pH 7.5, where the slightly negatively charged nature of the lignin substrate is more pronounced, governing electrostatic attraction of oppositely charged polymeric substances. An increase in the adsorption was further found when the electrolyte concentration was increased. In comparison, both PAA and the anionic PEC showed remarkably high adsorption to the lignin model film. The adsorption of PAA was further studied on silica and was found to be relatively low even at high electrolyte concentrations. This indicated that the high PAA adsorption on the lignin films was not induced by a decreased solubility of the anionic polyelectrolyte. The high levels of adsorption on lignin model surfaces found both for PAA and the anionic PAA-PAH polyelectrolyte complex points to the presence of strong nonionic interactions in these systems.     

Polyelectrolyte adsorption on charged surfaces: study by electrokinetic measurements

In order to describe the influence of cationic polyelectrolytes on flocculation of disperse systems the adsorption of poly (diallyldimethylammonium chloride) (PDADMAC) onto silica, mica and acidic polymer latex was investigated. The plateau value of the adsorption isotherms grows with increasing surface charge density of the substrates and electrolyte concentration. The adsorbed layer of the polycation was characterized by zeta potential measurements with KCl solutions of constant ionic strength and varied pH. The zero point of the charge as well as the shape of the zeta potential–pH plot depends on the coverage of the surface with polycations. For fully covered substrates the zero point of the charge as well as the pK_A and pK_B values calculated by a stochastic search programme are independent of the substrate. Maximum flocculation was observed at about 30% of the plateau value of the adsorption isotherms.     

Adsorption kinetics of laponite and ludox silica nanoparticles onto a deposited poly(diallyldimethylammonium chloride) layer measured by a quartz crystal microbalance and optical reflectometry

A quartz crystal microbalance with dissipation (QCM-D) and an optical reflectometer (OR) have been used to investigate the adsorption behavior of Laponite and Ludox silica nanoparticles at the solid-liquid interface. The adsorption of both Laponite and Ludox silica onto poly(diallyldimethylammonium chloride) (PDADMAC)-coated surfaces over the first few seconds were studied by OR. Both types of nanoparticles adsorbed rapidly and obtained a stable adsorbed amount after only a few minutes. The rate of adsorption for both nanoparticle types was concentration dependent. The maximum adsorption rate of Ludox nanoparticles was found to be approximately five times faster than that for Laponite nanoparticles. The QCM data for the Laponite remained stable after the initial adsorption period at each concentration tested. The observed plateau values for the frequency shifts increased with increasing Laponite particle concentration. The QCM data for the Ludox nanoparticles had a more complex long-time behavior. In particular, the dissipation data at 3 ppm and 10 ppm Ludox increased slowly with time, never obtaining a stable value within the duration of the experiment. We postulate here that this is caused by slow structural rearrangements of the particles and the PDADMAC within the surface adsorbed layer. Furthermore, the QCM dissipation values were significantly smaller for Laponite when compared with those for Ludox for all nanoparticle concentrations, suggesting that the Laponite adsorbed layer is more compact and more rigidly bound than the Ludox adsorbed layer.     

Viscoelastic properties of cationic starch adsorbed on quartz studied by QCM-D

The adsorption and viscoelastic properties of layers of a cationic polyelectrolyte (cationic starch, CS, with 2-hydroxy-3-trimethylammoniumchloride as the substituent) adsorbed from aqueous solutions (pH 7.5, added NaCl 0, 1, 100, and 500 mM) on silica were studied with a quartz crystal microbalance with dissipation (QCM-D). Three different starches were investigated (weight-average molecular weights M(w) approximately 8.7 x 10(5) and 4.5 x 10(5) with degree of substitution DS = 0.75 and M(w) approximately 8.8 x 10(5) with DS = 0.2). At low ionic strength, the adsorbed layers are thin and rigid and the amount adsorbed can be calculated using the Sauerbrey equation. When the ionic strength is increased, significant changes take place in the amount of adsorbed CS and the viscoelasticity of the adsorbed layer. These changes were analyzed assuming that the layer can be described as a Voigt element on a rigid surface in contact with purely viscous solvent. It was found that CS with low charge density forms a thicker and more mobile layer with higher viscosity and elasticity than CS with high charge density. The polymers adsorbed on the silica even when the ionic strength was so high that electrostatic interactions were effectively screened. At this high ionic strength, it was possible to study the effect of molecular weight and molecular weight distribution of the CS on the properties of the adsorbed film. Increasing the molecular weight of CS resulted in a larger hydrodynamic thickness. CS with a narrow molecular weight distribution formed a more compact and rigid layer than broadly distributed CS, presumably due to the better packing of the molecules.     

Polymerized rodlike micelle adsorption at the solid-liquid interface

The adsorption of rodlike polymer-micelle aggregates of cetyltrimethylammonium 4-vinylbenzoate (p-C16TVB) at the silica-water interface has been characterized using a combination of quartz crystal microbalance with dissipation monitoring (QCM-D) and atomic force microscopy (AFM) studies. Adsorption isotherm data, recorded by QCM-D, indicate a two-stage mechanism: an adsorbed film of free CTA+ ions is initially produced at low concentrations until the surface is charge reversed, whereupon the weakly anionic aggregates can adsorb and the adsorbed mass is seen to increase dramatically. The adsorbed rodlike micelle aggregates are seen to form a close-packed monolayer from AFM images with a high degree of order over micrometer length scales. AFM force-distance data indicate that the adsorbed aggregates retain their cylindrical structure and little or no flattening is seen. Rinsing of the film did not result in removal of the adsorbed layer, and the persistence of these nanoscale ordered films at the solid-liquid interface suggests many possible applications.     

Preparation and characterization of polymer composite multilayers on SiO2

Poly(diallyldimethylammonium chloride) (PDADMAC) and poly(sodium 4-styrenesulfonate) (PSS) have been consecutively adsorbed onto 1.5-microm charged silica (SiO2) particles. Time-dependent adsorption studies indicate that, due to the strong ionic charge of the dissociated polycation in water, adsorption is complete in less than 30 min. Indications of the maximum adsorption density, changes in surface charge, and stability of the layered particles are demonstrated through adsorption isotherms and electrophoretic mobility (EPM) measurements. Further stability of the PDADMAC layer is demonstrated through multiwashing with ultra pure deionized water. Preliminary desorption studies of the PSS layer also illustrate a stabilized two-layer system. Due to the nature of the electrostatic charges on the surface of the SiO2 core particles and both polyelectrolytes in aqueous media, the use of polyelectrolytes as layering elements serves as a model for the assembly of time-released drug delivery particle systems.     

Adsorption of polyelectrolytes on colloidal latex particles, electrostatic interactions and stability behaviour

The stabilization and flocculation behaviour of colloidal latex particles covered with cationic polyelectrolytes (PE) is studied with photon correlation spectroscopy and zetapotential measurements. Diffusion coefficients, flocculation rate constants and zetapotentials have been determined as a function of adsorbed amount of cationic poly-(diallyl-dimethyl-ammoniumchloride) (PDADMAC) of different molar masses and of statistic copolymers of DADMAC and N-methyl-N-vinyl-acetamide (NMVA) of various compositions in water and at high ionic strength. Flocculation by van der Waals attraction can be observed if the zetapotential is low. This occurs, if the surface charge is screened by the oppositely charged cations. Furthermore, in the case of adsorption of high molecular polycations mosaic flocculation occurs if the adsorbed amount is low. At high ionic strength, flocculation takes place if the adsorbed amount is below the adsorption plateau. If the adsorption plateau is reached the suspensions become stabilized. In water the charge reversal at full coverage leads to electrosteric stabilization both with low and high molar mass polycations. At high ionic strength only polycations with high molar mass are able to stabilize the suspension. If a certain molar mass of the polycation is exceeded, steric stabilization of the suspension occurs due to the formation of long adsorbed PE tails and their osmotic repulsion. The layer thicknesses are determined as a function of the molar mass. Received: 4 July 2000/Accepted: 18 August 2000     

Layer-by-layer assemblies of chitosan and heparin: effect of solution ionic strength and pH

The growth of polysaccharide multilayers consisting of positively charged chitosan (CH) and negatively charged heparin (HEP) was monitored in situ by employing a quartz crystal microbalance (QCM-D) and dual-polarization interferometry (DPI). The main focus was on how the physicochemical properties of the solution affect the growth and structure of the resulting multilayer film. These results showed that when increasing the ionic strength of the polysaccharide solutions at a fixed pH, both the "dry" (optical) (DPI) mass and wet (QCM) mass of the adsorbed multilayer film increased. The same effect was found when increasing the pH while keeping the ionic strength constant. Furthermore, the growth of multilayers showed an exponential-like behavior independent of the solution conditions that were used in this study. It was also established that chitosan was the predominant species present in the chitosan-heparin multilayer film. We discuss the viscoelastic properties of the adsorbed layers and their variation during the multilayer buildup. Interestingly and contrary to common interpretation of the QCM-D results, we found that under one particular solution condition (pH 4.2 and 30 mM NaCl) the increase in the dissipation of oscillation energy from the adsorbed layer was a consequence of layer stiffening rather than indicating a more hydrated and viscous film. On the basis of the widely used Voigt viscoelastic model for an adsorbed layer, we show that it is the film viscosity and shear that define the layer viscoelasticity (structure) of the film and not the absolute value of energy dissipation, which in fact can be very misleading.