Electroreduction of molybdenum(VI) at a prehydrogenated platinum electrode

The use of hydrogenated platinum electrodes allows observation of the electroreduction of some oxygenated ions, which is otherwise masked by the reduction of the hydrogen ion. The present paper deals with the reduction of molybdenum(VI) at a prehydrogenated platinum electrode in acid solutions. The experimental conditions for the electrode hydrogenation process are the following: 90 min at a cathodic current density of about 7 A/cm(2) for microelectrodes with an area of 0.02-0.03 cm(2); about 120 min at a current density of 1.5-2 A/cm(2) for microelectrodes with an area of 0.25-0.35 cm(2). The reduction of molybdenum(VI) in 0.8-1.6M H(2)SO(4) occurs in two consecutive steps: the more cathodic wave [Mo(V) to Mo(III)] is for the most part masked by the reduction of the solvent; the less cathodic wave [Mo(VI) to Mo(V)] takes place at E(1 2 ) values of about +0.07 V, is well shaped, diffusion-controlled and usable for the determination of molybdenum down to 4 x 10(-5)M or 6 x 10(-5)M if a rotating disk electrode is used. Interferences from diverse ions have been studied. A generalization of the effect of electrode hydrogenation on the reduction of those oxygenated ions so far studied [i.e., vanadium(IV), uranium(VI) and molybdenum(VI)] is presented.     

Coulometric determination of uranium with a platinum working electrode

Experimental conditions have been established which enable uranium to be determined coulometrically by the reduction of uranium(VI) to uranium(IV) at a platinum working electrode, by controlled-potential or controlled-potential-limit techniques. The procedure has been used successfully as a subsidiary method in the routine determination of uranium in pure uranyl nitrate solutions. The platinum electrode has several important practical advantages over the well established mercury-pool electrode for the coulometric determination of uranium. The consecutive determination of iron(III) and uranium(VI), or plutonium(IV) and uranium(VI) can be carried out with the same working electrode in the same solution and the coulometric oxidation of uranium(IV) to uranium(VT) is practicable. The rate of stirring of the cell liquor is much less critical in the case of the platinum electrode. Two main problems had to be overcome before a practical procedure could be achieved; hydrogen evolution during the uranium(VI)-(IV) reduction had to be eliminated so that 100% current efficiency could be obtained for the desired reaction and electrode-surface poisoning phenomena had to be controlled so that reaction times could be kept reasonably short. It was found that selection of a hydrochloric acid base solution containing a small amount of bismuth(III) enabled hydrogen evolution to be avoided: also electrode-surface poisoning with this base solution was not particularly serious and could be maintained at a satisfactorily low level by occasionally anodizing the electrode in dilute sulphuric acid. Bismuth(III) forms a complex with chloride ions and its presence increases the hydrogen overvoltage at the working electrode: no visible deposit of bismuth metal forms on the electrode during the uranium reduction. Samples containing nitrate can be analysed provided sulphamic acid is added to this hydrochoric acid base solution.     

Voltamperometric determination of uranium and plutonium in alkaline solutions

The simultaneous determination of U(VI), Pu(VI), Pu(V) in 0.5–4.0 M NaOH has been elaborated by means of classical and differential pulse voltamperometry. U(VI) is determined with a dropping mercury electrode (DME) at the half-wave potential of E_1/2=–0.89 V vs. Ag/AgCl reference electrode due to reduction to U(V). The limiting current or peak heights are proportional to uranium(VI) concentration in the range of 1.3.10^–7–3·10^–4 M U(VI). Deviation from proportionality is observed for higher concentrations due to polymerization of uranates. Pu(VI) and Pu(V) are determined with a platinum rotating electrode at E_1/2=–0.02 V due to the reaction Pu(VI)+e^–»Pu(V) and with DME at E_1/2=–1.1 V due to the reduction to Pu(III). The limiting currents of both Pu(VI) and Pu(V) are proportional to their concentrations in the range of 4·10^–6–1.2·10^–3 M Pu. The determination of U(VI), Pu(VI), Pu(V) is not interfered by the presence of the following salts: 2M NaNO₃, 2M NaNO₂, 1.5M NaAlO₂, 0.5M NaF and ions of Mo(VI), W(VI), V(V), Cu(II). The presence of CrO ₄ ^2– and FeO ₂ ^– ions disturbs the determination of U(VI) in 1–4M NaOH, however, contribution of the reaction Fe(III)+e^–»Fe(II) to uranium reduction peak can be calculated from the height of the second peak Fe(II)+2 e^–»Fe(0).     

Constant-current coulometric determination of uranium in the pure metal

A new method is proposed for the highly precise and accurate constant-current coulometry of uranium in high-purity uranium. Precisely weighed amounts of uranium and pure iron are dissolved in 7 M sulfuric acid containing some hydrogen peroxide (40% $\text{v}\text{v}$). The solution is quantitatively transferred to the coulometric cell by rinsing with 1 M H₂SO₄, saturated with cerium(III) sulfate. The first step is the quantitative electro-chemical reduction to U(IV), Fe(II) and Ce(III) on a gold gauze electrode at constant current (100 mA) until evolution of hydrogen is observed. The hydrogen is then removed by flushing the solution with very pure nitrogen until the potential of a platinum gauze electrode reaches a constant value. Oxidation on the gold gauze electrode is carried out under precisely controlled constant current; after the quantitative oxidation of U(IV) to U(VI) and Fe(II) to Fe(III), and crossing the end-point, this end-point is determined very precisely potentiometrically through back-titration by successive current injections of 10 mA during 1 s. The method was tested on a NBS reference material, uranium (NBS 960).     

Formation and Oxidation of Hydrogen Molybdenum Bronze on Platinum Electrode in Sulfuric Acid Solution

Hydrogen molybdenum bronze (HxMoO3) can be electrodeposited on platinum and oxidized in two steps to the hydrogen molybdenum bronze with less amount of hydrogen HyMoO3 (y相似文献   

Kinetics and mechanism of chromate reduction with hydrogen peroxide in base

[Cr(VI)O(4)](2)(-) is reduced to [Cr(V)(O(2))(4)](3)(-) by hydrogen peroxide in strongly basic media where the acid dissociation of H(2)O(2) (pK(a) = 11.65) is appreciable. The reaction is first order in chromium(VI) and inhibited by hydroxide. The hydrogen peroxide dependence is defined by the form of the effective pseudo-first-order rate constant: k(eff) = [H(2)O(2)](3)/(K(1) + K(2)[H(2)O(2)] + K(3)[HO(2)(-)]) with K(1) = 175(43) s x M(3), K(2) = 403(18) s x M(2), and K(3) = 1422(34) s x M(2). Hydrogen peroxide anion initially attacks chromate, and subsequent equilibrium steps that exchange oxo groups for three peroxo groups precede a rate-determining, one-electron, intramolecular reduction step.     

超微量铂丶铑连续催化极谱测定及其催化波机理的探讨

For simultaneous determination of ultramicro amounts of platinum and rhodium the optimum condition has been described as 1.5N H2SO4-1.2% NH4Cl-0.0012M (CH2)6N4-0.003% N2H4XH2SO4. Both platinum and rhodium produce hydrogen catalytic waves with peak potential at-1.03 V and - 1.27 V (vs. S. C. E.) and the peak height of differential wave in single-sweep polarograph is directly proportional to the concentration of the metals in the range from 0.05 ppb to 1.0 ppb for platinum and from 0.0025 ppb to 0.1ppb for rhodium, respectively. The influence of other platinum group metals and some base metals on the height of catalytic waves has been examined. It has been shown that the method is very selective. It is applied even at 200:1 or at 1:10 (Pt:Rh). The mechanism of the catalytic waves has been discussed. The catalytic waves of both platinum and rhodium are due to "surface catalytic wave of hydrogen". The wave of rhodium can be attributed to catalytic discharge of hydrogen ion by the complex (Rh(CH2O)2Cl4)-. One of the ligands, formaldehyde, is the product of hydrolysis of hexamethylenetetramine. The wave of plainum can be attributed to catalytic discharge of hydrogen ion by the complex (PtACl5)-, where a denotes intermediate product (a substance containing CH2=N group) formed during the hydrolysis of hexamethylenetetramine. The role of hydrazine sulfate in catalytic system has been shown. Hydzazine can react with formaldehyde to from (CH2=N)2 which promotes the growth of platinum catalytic wave and in this way the concentration of formaldehyde in the system can be controlled.     

Comparative study of uranyl(VI) and -(V) carbonato complexes in an aqueous solution

Electrochemical, complexation, and electronic properties of uranyl(VI) and -(V) carbonato complexes in an aqueous Na2CO3 solution have been investigated to define the appropriate conditions for preparing pure uranyl(V) samples and to understand the difference in coordination character between UO22+ and UO2+. Cyclic voltammetry using three different working electrodes of platinum, gold, and glassy carbon has suggested that the electrochemical reaction of uranyl(VI) carbonate species proceeds quasi-reversibly. Electrolysis of UO22+ has been performed in Na2CO3 solutions of more than 0.8 M with a limited pH range of 11.7 < pH < 12.0 using a platinum mesh electrode. It produces a high purity of the uranyl(V) carbonate solution, which has been confirmed to be stable for at least 2 weeks in a sealed glass cuvette. Extended X-ray absorption fine structure (EXAFS) measurements revealed the structural arrangement of uranyl(VI) and -(V) tricarbonato complexes, [UO2(CO3)3]n- [n = 4 for uranyl(VI), 5 for uranyl(V)]. The bond distances of U-Oax, U-Oeq, U-C, and U-Odist are determined to be 1.81, 2.44, 2.92, and 4.17 A for the uranyl(VI) complex and 1.91, 2.50, 2.93, and 4.23 A for the uranyl(V) complex, respectively. The validity of the structural parameters obtained from EXAFS has been supported by quantum chemical calculations for the uranyl(VI) complex. The uranium LI- and LIII-edge X-ray absorption near-edge structure spectra have been interpreted in terms of electron transitions and multiple-scattering features.     

Preconcentration and determination of uranyl ions on electrodes modified by tri-n-octylphosphine oxide

The application of electrodes modified by tri-n-octylphosphine oxide (TOPO) to the determination of uranium in aqueous solutions is investigated. Selective preconcentration of uranium(VI) by chemical reaction with the modifying molecule is followed by cyclic voltammetry. A hanging mercury drop electrode (HMDE) can be modified easily but the reproducibility of results is not good. When a TOPO-modified glassy carbon electrode is used, uranium(VI) can be preconcentrated from stirred solutions, and the cathodic voltammograms show an increase of current or a peak at about -0.75 V vs. SCE, depending on the uranium concentration of the solution. The effects of preconcentration time, pH and electrode potential during the preconcentration are discussed. The detection limit is in the 10^-9 M range for 45 min of preconcentration. The procedure is fairly selective for uranyl ions, but oxidizing agents interfere. Some tests on sea water are reported.     

镉离子在H2SO4溶液中极谱行为的研究

本文研究了在没有动物胶的0.5M H_2SO_4溶液中镉离子的极谱行为,得到了如下的结果:(1)在0.050～20.0mM CdSO_4 0.5M H_2SO_4的十种溶液中测得的电流-电位曲线都有良好的波形、恒定的极限扩散电流和易于确定的半波电位.这些曲线上都没有极谱极大出现;其极限扩散电流(波高)与镉离子的浓度成正比.在镉离子低浓度(0.050～0.20mM)时,半波电位保持不变,在镉离子高浓度(1.00～20.0mM)时,也仅有很小的变化.故镉离子在0.5MH_2SO_4,溶液中的电流-电位曲线可供定量和定性测定之用.(2)镉离子在低浓度时的极谱波是一种可逆波.(3)前人在H_2SO_4溶液中研究镉离子时之所以没有能得到令人满意的极谱行为的原因是他们在H_2SO4溶液中添加了动物胶的缘故.(4)作者从得到的波形良好的电流-电位曲线上,测定了25±0.2℃时镉离子在0.5M H_2SO_4溶液中的扩散电流常数、半波电位和电极反应中得失的电子数.结果如下: i_d/cm~(2/3)t~(1/6)=3.97μA/mM·mg~(2/3)·s~(-1/2) E_(1/2)=-1.011V(0.5M硫酸亚汞电极)=-0.559V(饱和甘汞电极) n=2 这些数据比Lingane的数据,扩散电流常数2.6μA/mM·mg~(2/3)·s~(-1/2)和半波电位-0.59V(饱和甘汞电极)],要合理些.     

Voltammetric study and electrochemical detection of hexavalent chromium at gold nanoparticle-electrodeposited indium tinoxide (ITO) electrodes in acidic media

The voltammetric behavior of hexavalent chromium species (Cr(VI)) was respectively studied at ITO, bulk Au, and Au-electrodeposited electrodes in 0.01 M NaCl aqueous solutions containing 0.01 M HCl. It was found that performance degradation of the ITO electrodes toward the reduction of Cr(VI) can be suppressed by modifying the electrode surface with gold nanoparticles (AuNPs), which were formed on ITO electrodes by potential-sweeping or potential-step electrodeposition in a 0.01 M Na(2)SO(4) solution containing 1 mM HAuCl(4) x 3 H(2)O and 0.01 M H(2)SO(4). After the modification, the surface of ITO electrodes turned to the characteristically red or blue color exhibited by AuNPs. The gold nanoparticle-electrodeposited indium-tinoxide electrode (AuNP-ITO) demonstrates unique catalytic behavior, higher sensitivity and stability in the reduction of Cr(VI). Cr(VI) species was detected by either cyclic voltammetry or hydrodynamic amperometry. By cyclic voltammetry, the dependence of cathodic peak current on concentration was linear from 5 to 100 microM with a detection limit of 2 microM (sigma=3), and linearity was obtained from 0.5 to 50 microM by hydrodynamic amperometry where a constant potential of +0.2V (vs. Ag/AgCl) was applied and a batch-injection cell was employed. For hydrodynamic amperometry, the detection limit was 0.1 microM (sigma=3).     

Adsorptive stripping voltammetry determination of molybdenum(VI) in water and soil

A differential pulse stripping voltammetry method for the trace determination of molybdenum(VI) in water and soil has been developed. In 0.048M oxalic acid and 6 x 10(-5)M Toluidine Blue (pH 1.8) solution, Mo(V), the reduction product of Mo(VI) in the sample solution, can form a ternary complex, which can be concentrated by adsorption on a static mercury drop electrode at -0.1 V (vs. Ag/AgCl). The adsorbed complex gives a well-defined cathodic stripping current peak at -0.30 V, which can be used for determining Mo(VI) in the range 5 x 10(-10)-7 x 10(-9)M, with a detection limit of 1 x 10(-10)M (4 min accumulation). The method is also selective. Most of the common ions do not interfere but Sn(IV) and large amounts of Cu(2+), Ag(+) and Au(3+) affect the determination.     

The uranium-Xylidyl Blue I complex and its application in linear sweep polarography

The linear sweep polarographic wave of the uranium-Xylidyl Blue I complex in ethylenediamine-1,10-phenanthroline-hydrochloric acid medium has been studied. The complex, corresponding to UO(2)(XBI)(2-)(2) with log beta' = 9.09 (by polarography), 8.81 (by spectrophotometry), is strongly adsorbed on the surface of the mercury electrode. The polarographic wave is attributed to the reduction of Xylidyl Blue I in the complex. The method is very sensitive with a detection limit of 3 x 10(-8)M. The wave height is proportional to the concentration of uranium over the range 8 x 10(-8)-7 x 10(-6)M. Solvent extraction is used to separate possible interferences. The recommended procedure has been applied to the determination of trace amounts of uranium in ores.     

Synthesis, spectroscopy, and electrochemistry of copper(II) complexes with N,N'-bis(3,5-di-t-butylsalicylideneimine)polymethylenediamine ligands

Bulky salen CuL(x) derived from aliphatic polymethylene diamines, H(2)N-(CH(2))(x)-NH(2), where n = 2-6, and 3,5-di-t-butylsalicylaldehyde (H(2)L(x)) and some corresponding tetrahydrosalan complexes (CuL(x)') have been synthesized and characterized by their IR, UV-vis absorption and EPR spectra, by magnetic moments and by cyclic voltammetry in acetonitrile (for H(2)L(x)) and DMF (for CuL(x)). Complexes CuL(x) and CuL(x)' are magnetically normal (mu(exp) = 1.83-1.91 mu(B)). EPR spectra CuL(x) characterized by the axial g and A(Cu) tensors with g parallel > g perpendicular and without (14)N-shf resolution in CHCl(3)/toluene at 300 and 150K. The CV studies on acetonitrile solutions of H(2)L(x) revealed a well-defined quasi-reversible redox wave at E(1/2) = 0.95-1.15 V versus Ag/AgCl but CV of the CuL(x) complexes in DMF exhibit weak pronounced irreversible oxidation waves at E(pa)(1) = 0.51 - 098 V and E(pa)(2) = 1.16 - 1.33 V attributable to metal centered Cu(II/III) and ligand centered CuL(x)/CuL(x)*+ couples, respectively. A poorly defined wave was observed for the quasi-reversible reduction Cu(II)/Cu(I) at potentials less than -1.0 V.     

Determination of hydrogen peroxide based on a metal dispersed sol-gel derived ceramic-graphite composite electrode

A new copper dispersed ceramic-graphite composite electrode was fabricated by the initial mixing of copper nitrate and (3-mercaptopropyl)trimethoxy silane (MPS) followed by stirring with graphite powder. The combination of the metal catalysis and the advantages of the ceramic composite favored the electrocatalytic reduction of hydrogen peroxide (H2O2) at a reduced overpotential of -0.2 V with good sensitivity, stability and reproducibility. The sensor showed a good linear response to H2O2 in the range from 8.3 x 10(-6) M to 2.0 x 10(-3) M with a correlation coefficient of 0.9989 and the detection limit was 6.2 x 10(-6) M (S/N =3).     

Studies on the polarographic behaviour of estazolam

In 0.1M NH(3)-NH(4)Cl buffer (pH 9.2) a sensitive 2-electron reduction wave of estazolam is obtained by single-sweep oscillopolarography. The peak potential is -1.08 V (vs. SCE). The peak height is proportional to the concentration of estazolam over the range 1.0 x 10(-7)-9.0 x 10( partial differential)M. The detection limit is 5.0 x 10(-8)M. The behaviour of the reduction wave has been studied and applied to the determination of estazolam. The reduction process is irreversible and the wave shows adsorptive characteristics, the behaviour obeying the Frumkin adsorption isotherm. The adsorption coefficient beta is 1.16 x 10(6) 1./mole and the interaction factor alpha is -1.06. The mechanism of the electrode reaction is discussed.     

Controlled potential coulometry: the application of a secondary reaction to the determination of plutonium and uranium at a solid electrode

A method is described for the simultaneous determination of plutonium and uranium in mixed oxides by controlled potential coulometry at a gold working electrode in two stages: first a coulometric oxidation, at 0.73 V vs. a silver/silver chloride electrode, of Pu(III) and U(IV) to Pu(IV) and U(VI) by a combination of a direct electrode reaction and a secondary chemical reaction proceeding concurrently, and secondly, a coulometric reduction at 0.33 V of Pu(IV) to Pu(III), leaving uranium as U(VI). The determination is carried out in a mixture of sulphuric and nitric acids, and Ti(III) is used to reduce plutonium and uranium to Pu(III) and U(IV) before electrolysis. The precision (3sigma) of Pu:U ratio results obtained from mixtures containing about 30% and 2% plutonium was 0.5% and 1-5% respectively. The effect of experimental variables on the time taken to complete the coulometric determination is discussed.     

Chemical equilibria in the binary and ternary uranyl(VI)-hydroxide-peroxide systems

The composition and equilibrium constants of the complexes formed in the binary U(VI)-hydroxide and the ternary U(VI)-hydroxide-peroxide systems have been studied using potentiometric and spectrophotometric data at 25 °C in a 0.100 M tetramethylammonium nitrate medium. The data for the binary U(VI) hydroxide complexes were in good agreement with previous studies. In the ternary system two complexes were identified, [UO(2)(OH)(O(2))](-) and [(UO(2))(2)(OH)(O(2))(2)](-). Under our experimental conditions the former is predominant over a broad p[H(+)] region from 9.5 to 11.5, while the second is found in significant amounts at p[H(+)] < 10.5. The formation of the ternary peroxide complexes results in a strong increase in the molar absorptivity of the test solutions. The absorption spectrum for [(UO(2))(2)(OH)(O(2))(2)](-) was resolved into two components with peaks at 353 and 308 nm with molar absorptivity of 16200 and 20300 M(-1) cm(-1), respectively, suggesting that the electronic transitions are dipole allowed. The molar absorptivity of [(UO(2))(OH)(O(2))](-) at the same wave lengths are significantly lower, but still about one to two orders of magnitude larger than the values for UO(2)(2+)(aq) and the binary uranyl(VI) hydroxide complexes. It is of interest to note that [(UO(2))(OH)(O(2))](-) might be the building block in cluster compounds such as [UO(2)(OH)(O(2))](60)(60-) studied by Burns et al. (P. C. Burns, K. A. Kubatko, G. Sigmon, B. J. Fryer, J. E. Gagnon, M. R. Antonio and L. Soderholm, Angew. Chem. 2005, 117, 2173-2177). Speciation calculations using the known equilibrium constants for the U(vi) hydroxide and peroxide complexes show that the latter are important in alkaline solutions even at very low total concentrations of peroxide, suggesting that they may be involved when the uranium minerals Studtite and meta-Studtite are formed by α-radiolysis of water. Radiolysis will be much larger in repositories for spent nuclear fuel where hydrogen peroxide might contribute both to the corrosion of the fuel and to transport of uranium in a ground water system.     

Differential pulse polarographic determination of trace selenium(IV) and molybdenum(VI) using the catalytic hydrogen wave

In the presence of selenium(IV) and molybdenum(VI) a new polarographic peak appears which corresponds to a hydrogen catalytic wave. By differential pulse polarography a single, sharp peak at about -1.1 V is obtained, allowing trace determination of selenium(IV) and molybdenum(VI) in the range 1x10(-6)-5.0x10(-9) M with a linear calibration and a detection limit of 1.5x10(-9) M. The optimum conditions are found to be 0.1 M KNO(3) and a pH of about 3.2 (Britton-Robinson buffer). There is no serious interference from some ions when present at 1.0-40 times that of molybdenum. At higher amounts of interfering ions the interference is eliminated by the addition of EDTA.     

Direct electron transfer and bioelectrocatalysis of hemoglobin on nano-structural attapulgite clay-modified glassy carbon electrode

Direct electrochemistry of hemoglobin (Hb) on natural nano-structural attapulgite clay film-modified glassy carbon (GC) electrode was investigated. The interaction between Hb and attapulgite was examined using UV-vis, FTIR spectroscopy, and electrochemical methods. The immobilized Hb displayed a couple of well-defined and quasi-reversible redox peaks with the formal potential (E(0')) of about -0.366 V (versus SCE) in 0.1 M phosphate buffer solution of pH 7.0. The current was linearly dependent on the scan rate, indicating that the direct electrochemistry of Hb in that case was a surface-controlled electrode process. The formal potential changed linearly from pH 5.0 to 9.0 with a slope value of -48.2 mV/pH, which suggested that a proton transfer was accompanied with each electron transfer in the electrochemical reaction. The immobilized Hb exhibited excellent electrocatalytic activity for the reduction of hydrogen peroxide without the aid of an electron mediator. The electrocatalytic response showed a linear dependence on the H(2)O(2) concentration ranging from 5.4 x 10(-6) to 4.0 x 10(-4) M with the detection of 2.4 x 10(-6) M at a signal-to-noise ratio of 3. The apparent Michaelis-Menten constant K(M)(app) for the H(2)O(2) sensor was estimated to be 490 microM, showing a high affinity.