Development of a Poly(vinyl chloride)-based Nitrate Ion-selective Electrode

The authors developed a nitrate ion-selective electrode(ISE) based on poly(vinyl chloride)(PVC) membrane with methyltrioctylammonium nitrate as a carrier and 1-decanol as a plasticizer. The performance of the nitrate-sensitive membranes was optimized by tuning the composition of components. The electrode exhibits a linear response with a Nernstian slope of (52±1.0) mV per decade for the nitrate ion concentration ranging from 5.8×10^-5 mol/L to 1.0 mol/L. The electrode can be used to detect a low concentration of nitrate ions down to 3×10^-5 mol/L in a pH range of 2.1-11.5 without any compensation. The advantage of the electrode includes simple preparation, short response time and good repeatability. The detection performance of the novel electrode on nitrate ions has been tested for water samples.     

A nitrate-selective electrode based on tris(2,2',2"-salicylideneimino)triethylamine.

A new nitrate-selective liquid-membrane electrode based on the tris(2,2',2"-salicylideneimino)triethylamine-iron(III) complex has been developed. This electrode exhibits a linear Nernstian response over the range 10(-1)-10(-4) M of nitrate, with a slope of 54.3 +/- 0.9 mV per p[NO3]. The effects of the pH and the liquid-membrane composition were also investigated. The lifetime of the electrode is at least one month. The selectivity coefficients for ten monovalent ions were calculated. The preparation procedure of the electrode is very easy and inexpensive. Moreover, the proposed electrode was applied for the determination of nitrate in fertilizers.     

Measurement of nitrate and chlorate in swimming pool water by capillary zone electrophoresis

Capillary zone electrophoresis (CZE) of nitrate and chlorate in swimming pool water are described. Nitrate and chlorate were determined simultaneously with an indirect detection method in an electrolyte containing 10 mM chromate and 0.1 mM cetyltrimethylammonium bromide (CTAB). Where chloride concentration was so high that nitrate could not be determined satisfactorily because of interference, a direct detection technology was developed in which 10 mM sulfate and 0.1 mM CTAB were used as the buffer. The wavelength for indirect detection was 254 nm and 214 nm for direct detection. Relative standard deviations of the quantification of nitrate and chlorate in real samples were below 6%. The detection limits were 7 mug ml(-1) for chlorate, and 4 mug ml(-1) (indirect detection) and 0.4 mug ml(-1) (direct detection) for nitrate.     

Improvement of capillary zone electrophoresis sensitivity with artificial seawater as the background electrolyte utilizing transient isotachophoresis for the determination of nitrate and nitrate ions in seawater

We describe capillary zone electrophoresis (CZE) with transient isotachophoresis (ITP) for the determination of low concentrations of nitrite and nitrate ions in seawater. Bromide-free artificial seawater was adopted as background electrolyte (BGE) to eliminate the interference of high concentrations of salts in seawater. To reverse the electroosmotic flow (EOF), 3 mM cetyltrimethylammonium chloride (CTAC) was added to the BGE. High concentrations of chlorate were added to sample solutions as the terminating ion to generate the ITP process before the CZE separation. In general, the stacking effect increased with increasing amounts of chlorate injected into the capillary. The limits of detection (LODs) for nitrite and nitrate were 0.063 and 0.033 mg/L when the chlorate concentration was 600 and 200 mM, respectively; these were half of those obtained by CZE without the transient ITP. The LODs were obtained at a signal to noise ratio (S/N) of 3. The relative standard deviations (RSD, n = 10) of the peak areas for these ions were 3.2 and 2.9%. The RSDs of peak heights for these ions were 1.6 and 2.1%. The RSDs of migration times for these ions were 0.67 and 0.46%.     

Mercurous nitrate as a reductimetric reagent : The titration of various oxidising agents

It has been found that when excess of a solution containing ferrous ions is added to certain oxidising agents, the equivalent amount of ferric iron produced can be titrated accurately with mercurous nitrate, enabling the original oxidant to be assessed. Oxidising agents which have been determined in this way are potassium permanganate, potassium persulphate, ceric sulphate, sodium vanadate, potassium chlorate, hydrogen peroxide and potassium dichromate. The last substance provides a convenient primary standard for the standardisation of mercurous nitrate solutions.     

Chronocoulometric determination of nitrate on silver electrode and sodium hydroxide electrolyte

An electrochemical system that consists of a silver electrode in 0.01 M sodium hydroxide electrolyte was investigated in an effort to develop a sensitive in situ analytical method for nitrate. Cyclic voltammetry demonstrated that the proposed system has a high normalized sensitivity (2.47 A s(1/2) V(-1/2) M(-1) cm(-2)), compared to more complex electroanalytical schemes. Double-potential-step chronocoulometry was used to maximize the signal-to-noise ratio (SNR), and minimize interference from dissolved oxygen in the electrolyte. The integration period for double-potential-step chronocoulometry was determined by optimizing the extended Cottrell equation. The integrated current is proportional to nitrate up to 10 mM and the average detection limit is approximately 1.7 microM. Dissolved oxygen does not degrade performance. To examine the potential interference of other ions when analyzing nitrate, we measured the electrode response to 1000 microM each of NO(2-), Cl(-), PO(4)(3-), SO(4)(2-), F(-), CO(3)(2-), BO(2-), K(+), Ca(2+), and Sr(2+) with and without 1000 microM nitrate. Interference is negligible for most of the ions when nitrate is absent (i.e. <1% of the response to equimolar nitrate). However, interference is substantial (>20% increase or decrease in the electrode response to nitrate) for PO(4)(3-), Ca(2+), and Sr(2+) when equimolar nitrate is present.     

Normal pulse polarographic study on the effect of hydrolysis at an electrode, and the Mn(II)-catalysed reduction of nitrate and nitrite

In neutral unbuffered solutions containing dissolved oxygen, the normal pulse polarograms of certain metal ions [Pb(II), Cd(II), Zn(II), Co(II) and Mn(II)] produce peaks on the limiting plateaux. These peaks reflect the reduction of hydroxide species formed in the vicinity of the electrode. It has been found that Mn(OH)(2) formed at the electrode surface exerts a catalytic effect on the reduction of nitrate and nitrite ions, with formation of OH(-).     

Determination of chlorine containing species in explosive residues using chip-based isotachophoresis

A new method has been developed to allow the determination of the chlorate, chloride and perchlorate anions in inorganic explosive residues to be made using isotachophoresis (ITP). To enable a good separation of these species to be achieved the method involves the use of two complexing agents. Indium(III) is used to allow the determination of chloride whilst using nitrate as the leading ion and alpha-cyclodextrin is used to allow the separation of chlorate and perchlorate. Separations were carried out using a miniaturised poly(methyl methacrylate) (PMMA) separation device. The method was applied to analysing both model samples and actual inorganic explosive containing residue samples. Successful determinations of these samples were achieved with no interference from other anions typically found in inorganic explosive residues. Limits of detection (LOD) for the species of interest were calculated to be 0.80 mg l(-1) for chloride, 1.75 mg l(-1) for chlorate and 1.40 mg l(-1) for perchlorate.     

Studies with inorganic ion-exchange membranes

The pyridinium molybdoarsenate membrane shows a response to pyridinium ions and can be used to determine the concentration of these ions in the range 10(-3)-1M. The potentials generated across the membrane are reproducible and the response time is less than 1 min. There is no interference from certain inorganic and organic ions. The electrode can be used in the pH range 3-6 as well as in non-aqueous medium. Small additions of cetyltrimethylammonium bromide cause large shifts in the membrane potentials. A membrane, after being treated with this surfactant, shows a wider range of response to pyridinium ions. Precipitation titration of pyridinium nitrate has been monitored by using this membrane electrode.     

A nitrate-selective electrode based on bis(triphenylphosphine)iminium salts

A nitrate-sensitive electrode based on the ionic associates between bis(triphenylphosphine)iminium and nitrate ions in nitrobenzene solution is proposed. The electrode can be used for determinations of 10(-5) 0.1M nitrate in aqueous solutions.     

滴汞电极2.5次微分电分析法测定天然水中痕量钛

天然水中钛的定量分析有分光光度法、极谱法、催化波法等方法。微分电分析法尚未见报导。本文得出了以0.02M苦杏仁酸-4%氯酸钾(pH=3)为底液时,钛在滴汞电极上2.5次微分电分析法催化波,峰形明晰、干扰少、线性范围为1×10^-10-1×10^-7g/ml钛。可直接用于天然水中痕量钛的测定。     

Calixarene-based potentiometric ion-selective electrodes for silver

Four lipophilic sulphur and/or nitrogen containing calixarene derivatives have been tested as ionophores in Ag(I)-selective poly (vinyl chloride) membrane electrodes. All gave acceptable linear responses with one giving a response of 50 mV/dec in the Ag(I) ion activity range 10(-4)-10(-1)M and high selectivity towards other transition metals and sodium and potassium ions. This ionophore was also tested as a membrane coated glassy-carbon electrode where the sensitivity and selectivity of the conventional membrane electrode was found to be repeated. The latter electrode was then used in potentiometric titrations of halide ions with silver nitrate.     

Potentiometric detection in ion chromatography using a metallic copper indicator electrode

Summary A metallic copper electrode housed in a suitable flowcell is shown to be a sensitive and versatile potentiometric detector for ion chromatography. This electrode may be used for direct or indirect detection of many inorganic anions and cations and also for organic acids. In the direct detection mode, electrode response is based on either complexation of copper ions at the electrode surface by eluted species, or on oxidation and reduction reactions for eluted species which are strong oxidants or reductants. Direct detection is therefore applicable to such species as amino acids, organic acids, chloride, bromide, iodide, chlorate, bromate and iodate. Indirect detection is possible for anions which do not complex copper ions, provided a copper complexing ligand (such as phthalate) is used in the eluent; cations which complex this ligand are also detectable. Indirect detection may be used for species such as nitrite, nitrate, acetate, formate, succinate, benzoate, alkaline earth ions and transition metal ions. Electrode calibration relationships are discussed and sample separations are presented, together with some typical detection limits attainable in the direct and indirect detection modes.Presented in part at a National Symposium on Ion Chromatography, held at the University of New South Wales, Kensington, Australia, Nov. 21, 1984.     

基于三维纳米银修饰电极的硝酸根微型传感芯片研究

研制一种基于金叉指微电极阵列(IDA)的电流型硝酸根离子(NO-3)微传感电极芯片.基于微机电系统(Micro-Electro-Mechanical Systems,MEMS)工艺制备金IDA微电极,通过电化学沉积技术在IDA微电极表面修饰三维枝状结构纳米银敏感膜,利用敏感膜对硝酸根离子良好的电催化还原性能,采用脉冲方波伏安(SWV)电化学测量方法,实现对硝酸根离子在25～1000μmol/L浓度范围内的快速检测,灵敏度达9.5 nA/(μmol/L),线性度为99.98%,检测下限为10μmol/L.考察水体中常见的NO-2,F-,3PO 4-,SO 42-,2CO3-,NH+4,Na+和K+等离子对该传感芯片的干扰性能,传感芯片表现出较好的抗干扰性能.制备的三维枝状结构纳米银修饰IDA微电极可实现水环境(pH 5.0～9.0)中NO-3的电化学检测,对应用于自然水环境中硝酸根离子的现场检测具有积极意义.     

Flow Injection Analysis of Iodate Reduction on PEDOT Modified Electrode

Poly‐(3,4‐ethylenedioxythiophene) (PEDOT) films were electrodeposited by cyclic voltammetry on glassy carbon electrode at different anodic potentials in the range of 1.0–1.5 V (Ag/AgCl) and its electrocatalytic properties towards reduction of iodate were reported. The effect of the pH of the solution on the response of PEDOT electrode towards iodate also studied. The modified electrode was employed successfully as an amperometric sensor for iodate in a flow injection apparatus. The repeatability of the method for 14 injections of a μM iodate solution was 7%. Interference from other oxidant anions such as nitrate was not noticeable, whereas bromate, chlorate and nitrite interfere at slight levels.     

离子选择电极阵列土壤中硝态氮测定

土壤硝态氮反映土壤短期氮素供应水平,实时了解土壤硝态氮的含量为精准农业和农业面源污染防控提供支撑,因此,在线实时检测土壤硝态氮方法突破就显得十分迫切。土壤硝态氮中的硝酸根离子在土壤中的高水溶性和流动性为全固态硝酸根离子选择电极高敏感检测土壤中硝态氮提供了条件,固态硝态氮离子选择电极的离子选择膜反应硝酸根离子在被测溶液中的浓度。采用全固态硝酸根离子选择电极,且与温度电极和pH电极融合组成电极阵列对土壤饱和溶液中的硝态根离子进行检测。设计了高输入阻抗运算放大电路对电极信号进行采集,并通过微处理控制蠕动泵完成土壤硝态氮待测溶液连续流动测量及实时传输结果。实验结果表明,电极响应时间≤15 s,斜率-51.63 mV/decade,线性范围10-5-10-2.2 mol/L,最低检测限10-5.23 mol/L。相对标准差在0.78%-4.47%范围内,加标回收率均在90%-110%以内。与国家标准紫外可见分光光度法测试结果相比,相关系数（R2）为0.9952,为土壤硝态氮在现场检测奠定技术基础。     

Development of a novel electrochemical cell for slab optical waveguide spectroscopy for in situ observation of methylene blue and anions on an electrode/electrolyte interface

A new spectroelectrochemical cell for slab optical waveguide (SOWG) spectroscopy was developed in order to observe in situ an electrode/electrolyte interface for bulk electrolysis. The new SOWG spectroelectrochemical cell has been evaluated by simultaneous electrochemical-absorption experiments of methylene blue (MB) using cyclic voltammetry (CV) and SOWG spectrometry. CV was performed in the SOWG spectroelectrochemical cell using indium tin oxide (ITO) coated glass as the working electrode, platinum wire as the counter electrode and a silver/silver chloride electrode (Ag/AgCl) as the reference electrode. Based on the CV and SOWG spectrometric data, it was found that the SOWG spectra showed the MB spectra on the electrode surface selectively and that SOWG with the cell would be useful as a tool for in situ study of an electrode/electrolyte interface. Using this cell, the effects of the supporting electrolytes, NaNO₃, KNO₃, CH₃COONa, and CH₃COOK on the absorbance of MB were examined at the potential of +0.8 V versus Ag/AgCl. The decrease in MB absorbance by nitrate ions was greater than that of acetate ions. Therefore the competitive adsorption of nitrate ions was stronger than that of acetate ions. Thus, the decrease in absorbance of MB in the presence of anions demonstrates the competitive adsorption of anions. These results show that the extent of specific adsorption of electrolytes was observed by measuring the SOWG absorbance intensity of MB.     

氯酸盐电还原机理的研究

本文利用Mo盘-Pt盘旋转电极研究了ClO_3的电还原过程, 并根据实验事实提出了一较完整的反应机理。我们首次检测到了ClO_3还原的中间产物ClO_2和Cl(或Cl_2)。其最终产物为Cl~-离子。     

Determination of monovalent inorganic anions in high-ionic-strength samples by electrostatic ion chromatography with suppressed conductometric detection

A new ion chromatographic (IC) system has been established by using micelles of 3-(N,N-dimethylmyristylammonio)propanesulfonate (Zwittergent 3-14) loaded onto a reversed-phase packed column as the separation column with an electronic rotary switching valve packed-bed suppressor for conductometric detection of inorganic anions. An aqueous H3BO3-Na2B4O7 solution has been demonstrated to be the most desirable eluent for this IC system. The relationship between retention time and the concentration of the borate eluent was determined for a series of model anionic analytes and this relationship was found to be opposite to that exhibited in a conventional anion-exchange IC system. The rapid elution and complete separation of monovalent inorganic anions were obtained by initially using a high-concentration borate solution as the eluent for a short-period, and then switching to a lower-concentration borate eluent to complete the separation. Detection limits for nitrite, bromide, nitrate, and chlorate were 0.85, 0.88, 0.95 and 4.8 microM, respectively, when a 7.0 mM Na2B4O7 eluent was used. Moreover, the ability to directly detect these monovalent anions in samples containing high concentrations of sulfate and/or chloride ions provided a major advantage of this approach.