Thermal properties of rhodium(III) chloride

Thermal decomposition of rhodium(III) chloride under inert, oxidative and reductive gas atmospheres was investigated in order to determine its thermal properties. Stoichiometries of the reactions occurring during heating are described. it is suggested that the chemical formula of soluble rhodium(III) chloride should be presented as RhCl₃·HCL·xH₂O. Cold crystallisation of anhydrous rhodium(III) chloride at a temperature of about 500°C was established. The procedure for quantitative determination of volatile matter (water and hydrochloric acid) content and rhodium content by thermogravimetry is given and discussed. The repeatability and reproducibility of the method are estimated. This revised version was published online in July 2006 with corrections to the Cover Date.     

Separation preconcentration method for platinum and rhodium from environmental samples using a chelating resin

A method of determining trace levels of platinum and rhodium in different samples was investigated. The method involves separation and preconcentration of the platinum and rhodium from the matrix by flow injection (FI) on-line coupled with electrothermal atomic absorption spectrometry (ETAAS) with Zeeman effect background correction. Platinum and rhodium were adsorbed on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel). The sorbed metals were directly eluted with nitric acid into the graphite furnace and determined by AAS.     

Rhodium complex with ethylene ligands supported on highly dehydroxylated MgO: synthesis, characterization, and reactivity

Mononuclear rhodium complexes with reactive olefin ligands, supported on MgO powder, were synthesized by chemisorption of Rh(C(2)H(4))(2)(C(5)H(7)O(2)) and characterized by infrared (IR), (13)C MAS NMR, and extended X-ray absorption fine structure (EXAFS) spectroscopies. IR spectra show that the precursor adsorbed on MgO with dissociation of acetylacetonate ligand from rhodium, with the ethylene ligands remaining bound to the rhodium, as confirmed by the NMR spectra. EXAFS spectra give no evidence of Rh-Rh contributions, indicating that site-isolated mononuclear rhodium species formed on the support. The EXAFS data also show that the mononuclear complex was bonded to the support by two Rh-O bonds, at a distance of 2.18 A, which is typical of group 8 metals bonded to oxide supports. This is the first simple and nearly uniform supported mononuclear rhodium-olefin complex, and it appears to be a close analogue of molecular catalysts for olefin hydrogenation in solution. Correspondingly, the ethylene ligands bonded to rhodium in the supported complex were observed to react with H(2) to form ethane, and the supported complex was catalytically active for the ethylene hydrogenation at 298 K. The ethylene ligands also underwent facile exchange with C(2)D(4), and exposure of the sample to carbon monoxide led to the formation of rhodium gem dicarbonyls.     

Organotin Leachates in Drinking Water from Chlorinated Poly(vinyl chloride) (CPVC) Pipe

A solid-phase extraction method, using a phenyl-bonded silica sorbent, was developed for the isolation of mono- and di-methyltin, -butyltin and -octyltin from drinking water. Recoveries averaged 92% over two tested sample weights and spiking levels. Ethyl derivatives were made by Grignard reaction for determination by gas chromatography–atomic absorption spectrometry (GC–AAS). Static and repetitive extraction studies were conducted at 24 and 65°C. Butyltins rapidly leached into drinking water kept in chlorinated poly(vinyl chloride) (CVPC) pipe samples. Monobutyltin and dibutyltin levels reached 19.8 (13.4 as Sn) and 197 (100.4 as Sn) ng g⁻¹ respectively in water samples collected from CPVC pipe heated to 65°C. Butyltins were still leached from CPVC pipe after 20 repetitive extractions, suggesting that new CPVC water systems would contaminate water with organotins for some time after installation. © 1997 John Wiley & Sons, Ltd.     

Studies on optimization of conditions for separating rhodium and platinum by cation-exchange

It has been established that, owing to the amphoteric properties of rhodium(III) hydroxide, by making a rhodium chloride solution alkaline (pH approximately 13) with sodium hydroxide and then acidifying to pH 2 with nitric acid it is possible to convert at least 99% of the rhodium into cationic forms. This fact is utilized for separation of rhodium(III) and platinum(IV) from chloride solutions on a sulphonic acid cation-exchanger in hydrogen form. Loss of rhodium in the separation process is < 1%. Platinum elution is complete. This method is suitable for separation of mixtures of rhodium and platinum (present in molar ratio between 1:200 and 20:1).     

Synthesis of macroporous poly(vinyldiethylenetriamine) chelating resin and the enrichment—separation of rhodium and iridium

Poly(vinyldiethylenetriamine) chelating resin was synthesized from macroporous poly(vinyl chloride) and used for the enrichment-separation of rhodium and iridium. The efficiency, rate and equilibrium constant adsorption of rhodium and iridium on the resin were determined and real samples were analysed. The mechanism of rhodium and iridium enrichment is discussed.     

中药化橘红元素煎出率的初步研究

利用原子吸收光谱法测定了中药化州橘红原生药及水煎液中元素的分布及含量，研究了各元素的煎出特征，计算了煎出率，说明仅从原药中元素种类和含量推测各元素与中药的药效关系是不合适的，必须考虑元素的可利用量及在相应剂型中的存在状态。     

Determination of rhodium in waters by Mg-W cell-electrodeposition and electrothermal atomic absorption spectrometry

A new concentration method of rhodium using Mg-W cell-electrodeposition has been developed. The method was combined with electrothermal atomic absorption spectrometry (ETAAS) with a tungsten tube atomizer. The optimal immersing time was 120 s. The most suitable pH for rhodium electrodeposition was 1.0. Under optimal conditions, the detection limit of rhodium by the ETAAS with the preconcentration was 13 ng ml(-1) (3S/N). The severe interferences on the AAS signal of rhodium by large amounts of Ca, Cu, Fe, K, Na, Pb and Zn were eliminated by the Mg-W cell-electrodeposition method. The method was applied to the determination of rhodium in river and sea water. The recovery of rhodium spiked environmental samples was in the range of 95.6-109%. The present Mg-W cell-electrodeposition method can be utilized in in-situ sampling of trace elements in environmental samples (water). Furthermore, after sampling, it is easy to carry and store the W-sheet without contamination for a long time.     

In Process Citation

The sample (< 1 mg) is burnt in an oxygen flask for the determination of rhenium. It is destroyed by a wet process in a Kjeldahl flask for the determination of rhodium or tellurium (sample <4-5 mg) or zirconium (sample <1.5 mg). These elements are determined spectrophotometrically. The following reactions are used: reduction of perrhenate by tin(II) chloride in the presence of 2,2'-furildioxime or thiourea, complexation of rhodium(III) by sodium hypochlorite, formation of iodotellurite, complexation of zirconium(IV) with Xylenol Orange.     

New ammonium surfactant-stabilized rhodium(0) colloidal suspensions: influence of novel counter-anions on physico-chemical and catalytic properties

Novel anionic species, such as hydrogen carbonate (HCO(3)(?)), fluoride (F(?)), triflate (CF(3)SO(3)(?)), tetrafluoroborate (BF(4)(?)) and chloride (Cl(?)) were investigated as new partners of water soluble N,N-dimethyl-N-cetyl-N-(2-hydroxyethyl) ammonium salts, used as a protective agent of rhodium colloids. The effect of the surfactant polar head on the micellar behavior, size and morphology of the nanospecies was studied by adapted physico-chemical experiments (surface tension measurements, dynamic light scattering, thermogravimetric and TEM analyses) and discussed in terms of strong or weak stabilization of the growing nanoparticles surface. Finally, the influence of the nanoenvironment generated by the surfactant with various counter-anions was evaluated via the hydrogenation of aromatics.     

熔融萃取法富集痕量铂和铑─石墨炉原子吸收光谱测定

本文报道以２－硫基苯并噻唑（ＭＢＴ）为络合剂，用熔融萘萃取痕量的铂和铑，继用石墨炉原子吸收光谱法直接测定之。文中曾对一些有关参数作了试验，并找出各参数的最优值，对共存离子的允许量也作了试验。最后用国家标样和部级管理样核对本法，结果令人满意。     

The passivation phenomenon of rhodium in fused lithium chloride + potassium chloride eutectic

The passivation phenomenon of rhodium was investigated in fused lithium chloride + potassium chloride eutectic by means of the potential sweep method. The current-potential curve obtained showed a typical N-shaped negative impedance. An anodic current rise was observed at +0.3 V vs. Ag/AgCl (0.1). The current was controlled by mass transfer and was ascribed to the dissolution of rhodium into rhodium(III) ions. The observed Flade potential was +0.45 V at 400°C. The passivation was found to occur due to the precipitation of supersaturated Rh(III) chloride onto the electrode surface. The residual current for the passivation was fairly high and the current increased significantly as the temperature was made higher. The dissolution current of rhodium into Rh(III) ions decreased with increase in the concentration of oxide ions. The fact revealed that the rhodium was passivated preferentially due to the formation of Rh(III) oxide. The residual current of the oxide passivation film was low enough. The thickness of the film corresponded to 10–20 atomic layers of the parent metal. Rhodium showed another anomalous passivation due to the formation of oxide. The oxide was formed at ?0.3 V and was reduced at ?0.6 V. It was considered to be a low valence rhodium oxide, RhO or Rh₂O. Rhodium was found to have a low chlorine overpotential. However, it was redissolved at the chlorine evolution region, above +1.25 V. The dissolution was not prevented even in the oxide ion containing melts.     

Effect of ring methylation on the photophysical, photochemical and photobiological properties of cis-dichlorobis(1,10-phenanthroline)rhodium(III)Chloride

Methylated analogues of cis-dichlorobis(1,10-phenanthroline)rhodium(III)chloride (BISPHEN) have been prepared in order to increase the hydrophobicity of the parent compound, and thus create octahedral rhodium (III) complexes suitable for use as anticancer and antiviral agents that can be photoactivated. The parent complex has been shown in earlier work to be unable to cross through cell membranes. Octamethylation, as in the case of cis-dichlorobis(3,4,7,8-tetramethyl-1,10-phenanthroline)rhodium(III)chloride (OCTBP), provides enough hydrophobicity to be taken up by KB tumor cells. It also provides a higher level of ground-state association with double-stranded DNA and increases the quantum efficiency of photoaquation by greater than 10-fold, relative to BISPHEN. OCTBP forms covalent bonds to deoxyguanosine when irradiated with the nucleoside, as has been seen with the parent complex. Irradiation of OCTBP in the presence of the KB or M109 tumor cell lines using narrow-band UVB (lambda = 311 nm) irradiation initiates a considerable amount of phototoxicity. There is evidence that OCTBP acts as a prodrug (i.e. after passing through the cell membrane the metal complex is photolyzed to cis-chloro aquo OCTBP, which may be the active phototoxic agent). OCTBP and the tetramethyl analogue cis-dichlorobis(4,7-dimethyl-1,10-phenanthroline)rhodium(III)chloride (47TMBP) also show photoaquation upon excitation with visible light (lambda > 500 nm), and indeed, some phototoxicity of KB cells is observed at these wavelengths as well. This is attributed to direct population of photoactive triplet-excited states. These results, together with our earlier studies of cis-dichloro[dipyrido(3,2-a: 2',3'-c)phenazine (1,10-phenanthroline)rhodium(III)chloride (DPPZPHEN) demonstrate that such octahedral rhodium complexes are viable "photo-cisplatin" reagents.     

Polyurethane foams as selective sorbents for noble metals : Quantitative extraction and separation of rhodium from iridium in hydrochloric acid containing tin(II) chloride

The distribution of rhodium(III) between polyether-type polyurethane foam and 0.5–5.0 mol dm^?3 hydrochloric acid in the presence of small amounts of tin(II) chloride is described. The distribution of rhodium is affected by the extraction temperature, acid concentration and the Sn(II):Rh ratio. The capacity of the polyurethane foam for rhodium is in excess of 0.5 mmol g^?1. Rhodium is presumably sorbed in the form of a chloro(trichlorostannato)rhodium(III/I) complex anion. Iridium is not extracted by the foam under corresponding conditions and can be separated quantitatively from rhodium.     

Partial separation of rhodium and iridium using polyurethane foam

Rhodium/III/ solutions react with tin/II/ chloride to form a short-lived yellow complex which is extracted by polyurethane foam. Iridium/IV/ solutions are decolourised by tin/II/ chloride but the metal is poorly extracted by foam. The rhodium/III/ complex is readily desorbed from foam using hydrochloric acid and acetone.     

Extraction of rhodium and iridium with 4-(non-5-yl) pyridine

The extraction of rhodium and iridium with 4-(non-5-yl)pyridine (NP) was investigated. The rate of rhodium extraction increases with increasing concentration of NP and chloride ions. Spectroscopic studies indicate that the extracted species is an ion pair, RhCl^3?₆ 3HNP⁺. Under the conditions of optimum Rh extraction ([Cl^?]=3.7 M, [NP]=0.3 M, [H]=0.08 M), iridium is also extracted by NP with similar efficiency in the form of IrCl^3?₆ 3HNP⁺. The use of hypophosphorous acid to labilize rhodium results in a better extraction of rhodium without significantly changing the extraction of iridium. The efficiency and kinetics of the rhodium extraction improve with increasing chloride concentration. For [Cl^?] ? 3.7 M, [H₃PO₂]=2.5 M, [NP]=0.3 M and Ph ≈ 1.6, 82% of rhodium is extracted in 4 min and 95% in 30 min.     

C60正丙胺铂,铑配合物的合成及其催化硅氢化性能

Ｃ６０与正丙胺反应,然后分别与氯亚铂酸钾或三氯化铑配合,制得出含配位氮原子的富勒烯铂,铑 配合物,它们均能有效地催化烯烃与三乙氧基硅烷硅氢加成,铂配合物还对苯乙烯有独特的催化性能,以近１００％的区域选择性得到α－加成产物,对催化机理进行了初步的探讨。     

Graft polymerization of styrene initiated by covalently bonded peroxide groups on silica

The graft polymerization of styrene initiated by immobilized peroxide groups was investigated. Three different types of modification reactions were used to introduce peroxide groups which are directly attached onto the surface of two different silica supports. Silanol groups were chlorinated using thionyl chloride or tetrachlorosilane. In another reaction pathway 1,3,5-benzenetricarbonyl chloride enabled the introduction of free acid chloride residues bonded onto the surface of silica. tert-Butyl hydroperoxide (TBHP) was used to transform the chlorosilyl and the acid chloride groups into peroxide residues. In a further reaction step the covalently bonded peroxides initiated the polymerization of styrene to form grafted polystyrene directly attached onto the silica support. Solid-state 13C CP/MAS NMR spectroscopy, and thermogravimetric and scanning electron microscope measurements enabled a clear structure and property elucidation of the different bonded phases. The highest amount of grafted polystyrene was achieved employing the acid chloride synthesis pathway with silica-gel, whereas modification of spherical silica only led to minor amounts of grafted polymer. The results contribute to the evolving need to understand particle surface modifications and may have positive impact on development of new HPLC stationary phases for improved elutant resolution.     

Polyurethane foam for the extraction of rhodium and its separation from iridium

The rate of reaction of rhodium with thiocyanate at 90 degrees in the presence of lithium chloride or sufficient hydrochloric acid and the subsequent extraction of the metal from hydrochloric acid medium by polyether-type polyurethane foam was investigated. The effect of the chloride salts of different cations decreased in the order Li(+) > Na(+) > K(+) indicating that Rh(SCN)(6)(3-) is extracted through a simple solvent-extraction mechanism rather than the "cation-chelation" mechanism. The separation of rhodium and iridium was also examined and the results indicated that in the presence of 5-fold excess of iridium, an average of 95 +/- 2% iridium remained in the aqueous phase while an average of 93 +/- 2% rhodium was retained by the foam.