The laser-induced discoloration of stonework; a comparative study on its origins and remedies

For understanding the phenomena associated with the discoloration observed in some cases of infrared laser cleaned stonework surfaces, a comparative study of three different types and morphologies of pollution encrustation and stone substrates was undertaken. Fragments originating from monuments with historic and/or artistic value, bearing homogeneous thin soiling on Pentelic marble (Athens, Greece), thick encrustation on Hontoria limestone (Burgos, Spain) and compact thin crust on gypsum decorations (Athens, Greece), have been studied on the basis of their composition and origin, together with the conditions that may induce yellowing effects upon their laser cleaning with IR wavelengths. While irradiation in the UV (i.e. at 355 nm) could not effectively remove the encrustations studied, irradiation at 1,064 nm was found efficient to remove all the studied pollution accumulations. Discoloration towards yellow was evident in all cases and at different levels, including the samples with intentional patination layer. To the limit of Raman detection no chemical alterations were detected on the irradiated areas while the presence of yellow polar compounds in all the pollution crusts studied supports the argument that the discoloration of the stone surfaces upon their IR irradiation may be due to the uncovering of existing yellow layers as result of the migration of these compounds inwards to the original stone surface. To correct and/or prevent such undesired coloration the use of IR and UV radiation both in sequential and synchronous mode was considered, with positive results.     

Two- and three-wavelength laser multiphoton ionization for highly sensitive detection in solution

Novel two- and three-wavelength laser multiphoton ionization techniques for highly sensitive detection in solution have been established. The photocurrent signal obtained for benzo[a]pyrene by irradiation at 355 nm in n-heptane was effectively enhanced by additional simultaneous irradiation at 532 and/or 1064 nm. The additional irradiation at 532 nm (5 mJ) doubled the signal-to-noise ratio, while that at 1064 nm (30 mJ) increased it 5.5-fold relative to that obtained when only the 355 nm radiation was used. The simultaneous action of 355, 532 (5 mJ) and 1064 (25 mJ) nm radiation further improved the S/N ratio; the detection limit was as low as 1.9 x 10(-10)M. The 532 nm radiation enhanced the photocurrent signal more effectively than did the 1064 nm radiation.     

氯分子束与钛表面激光化学反应动力学

本文采用飞行时间质谱技术测定了在紫外(355nm), 可见(560nm)和近代红外(1064nm)脉冲激光作用下, 氯分子束与Ti表面反应产物的质量分布和速度分布。所得结果表明, 不同波长激光诱导反应的主要产物相同, 有Ti, TiCl, TiCl3和TiCl4。在高能量密度的紫外激光作用下, 首次测得具有很高动能的原生Ti+。各种含Ti氯化物的飞行时间谱, 能满意地用单组分或多组分Maxwell-Boltzmann公式拟合和分析。上述激光诱导气-固表面反应的机理主要由氯分子在Ti表面上的解离吸附,吸附态氯原子在表面上生成TiClx(X=1～4)的连串反应以及激光诱导脱附所组成。近红外激光主要引起热脱附, 而紫外激光的作用还原可能有非热脱附过程。     

Influence of wavelength,irradiance, and the buffer gas pressure on high irradiance laser ablation and ionization source coupled with an orthogonal Time of Flight Mass Spectrometer

Influence of laser wavelength, laser irradiance and the buffer gas pressure were studied in high irradiance laser ablation and ionization source coupled with an orthogonal time-of-flight mass spectrometer. Collisional cooling effects of energetic plasma ions were proved to vary significantly with the elemental mass number. Effective dissociation of interferential polyatomic ions in the ion source, resulting from collision and from high laser irradiance, was verified. Investigation of relative sensitivity coefficients (RSC) of different elements performed on a steel standard GBW01396, which was ablated at 1064 nm, 532 nm, 355 nm, and 266 nm, has demonstrated that the thermal ablation mechanism could play a critical role with the first three wavelengths, while 266 nm induces non-thermal ablation principally. Experimental results also indicated that there is no evident discrepancy for most metal elements on RSCs and LODs among four wavelengths at high irradiance, except that high boiling point elements like Nb, Mo, and W have higher RSCs at higher irradiance regions of 1064 nm, 532 nm, and 355 nm due to thermal ablation. A geological standard and a garnet stone were also used in the experiment subsequently, and their RSCs and LODs for metal elements show nonsignificant dependence on wavelength at designated irradiances. All results reveal that relatively uniform sensitivity can be achieved at any wavelength for metal elements in the solids used in our experiments at an appropriate irradiance for the low pressure high irradiance laser ablation and ionization source.     

纳秒强激光电离苯产生高价碳离子的波长效应

The photoionization of seeded benzene beam by 25 ns laser pulse at wavelengths of 266,355 and 1064 nm has been studied by the time-of-flight mass spectrometry. The observed mass spectra at 266 nm and 355 nm at intensities of 1010-1011 W/cm2 indicate a multiphoton ionization and dissociation（MPID）process,in which C+,C2Hx+,C3Hx+,C4Hx+ and C6H6+ are main products. While at 1064 nm laser of similar intensities,the domain ion is C4+ which is produced from Coulomb explosion. The longer wavelength facilities the energy absorption rate during inverse bremsstrahlung,which leads to the resulting wavelength dependence of the multicharged atomic ions.     

基于共轭聚合物的纳米粒子用于肿瘤的近红外二区荧光成像及光热治疗

为提高生物组织荧光成像质量以及对肿瘤的高效光热治疗,设计合成了一种新型的窄带隙共轭聚合物(BDT-TTQ),并通过纳米沉积的方式将聚合物制备成水溶性纳米粒子(BDT-TTQ NPs).该共轭聚合物纳米粒子在1000~1200 nm近红外二区范围具有较好的吸收,在1064 nm的激发光下能实现1200~1400 nm的近红外二区荧光成像. BDT-TTQ NPs纳米粒子粒径分布较窄,形貌呈规则的球形且分散均匀,具有好的生物相容性.该纳米粒子既可以在体外实现较高的近红外二区荧光成像穿透深度,又可以实现对小鼠活体血管的高清晰度的近红外二区荧光成像.此外,BDT-TTQ NPs纳米粒子在1064 nm激光下展现出优异的光热转换效率,具有较高的光毒性,对体外的肿瘤细胞以及小鼠的异质瘤具有高的光热杀伤能力.     

Wavelength dependence of polyyne preparation by liquid-phase laser ablation using pellet targets

The amount of polyynes produced by Nd:YAG laser (355, 532, and 1064 nm) ablation of fullerene and graphite pellet targets was the largest for 1064 nm ablation, contrary to the powder target in the previous report. This result is believed to come from the difference in the main polyyne-production area in liquids in the optical cell, depending on the pellet and powder targets.     

Studies of Sb and Bi cluster produced by laser desorption

Direct production of cations and anions of metal clusters of Sb and Bi by laser evaporation in a vacuum has been studied. Bulk sample substrates are irradiated by 1064, 532 and 355 nm beams at variable intensity, and the ions produced are accelerated and identified by time-of-flight mass spectrometry. At 1064 nm, the cation distributions show that Sb ₃ ⁺ and Bi ₃ ⁺ are the most abundant species, while the monomer and dimer cations are almost non-existent. The anion spectra indicate very low yields of Sb^? and Bi^? with dominant dimer anion species. These patterns persist with laser power variation within the stable operation domain. With lower incident laser wavelength, the mass distributions are modified, favouring the production of the light cluster ions. In no circumstances were Sb and Bi ions withn>5 observed. Many of the observed phenomena can be explained if one assumes that for these elements, clusters withn<6 are formed on the substrate surface. Cluster ions are produced via a prompt desorption process, and are subjected to photon induced reactions due to the same incident laser beam. However, more detailed investigation of the desorption properties will be necessary to confirm such a desorption mechanism.     

The influence of laser wavelength and fluence on palladium nanoparticles produced by pulsed laser ablation in deionized water

Homogeneous spherical palladium (Pd) nanoparticles were synthesized by pulsed laser ablation of a solid Pd foil target submerged in deionized water, without the addition of any external chemical surfactant. The influence of laser wavelength (355, 532, and 1064 nm) and fluence (8.92, 12.74, and 19.90 J/cm²) on nucleation, growth, and aggregation of Pd nanoparticles were systematically studied. Microstructural and optical properties of the obtained nanoparticles were studied by field emission transmission electron microscopy (FETEM), energy dispersive X-ray spectroscopy, and UV–vis spectroscopy. FETEM micrographs indicate that the average nanocrystallite sizes are relatively low (3–6 nm) and homogeneous for the particles synthesized at the laser wavelengths of 355 and 532 nm. However, at a laser wavelength of 1064 nm, the average nanocrystallite size is relatively large and inhomogeneous in nature. Moreover, we observe that the mean diameter and production rate of particles increases with an increase in laser fluence. The selected area electron diffraction patterns obtained from isolated Pd nanoparticles show the characteristic diffused electron diffraction rings of polycrystalline materials with a face-centered cubic structure. Absorbance spectrum of the synthesized nanoparticle solution shows a broad absorption band, which corresponds to a typical inter-band transition of a metallic system, indicating the production of pure palladium nanoparticles. The present work provides new insights into the effect of laser wavelength and fluence on the control of size and aggregation of palladium nanoparticles in the liquid medium.     

Multiphoton-ionization of hydrogen atoms in intense laserfields

The interaction of hydrogen atoms with strong laser fields at intensities up to some 10¹³ W cm^?2 was studied experimentally at the wavelengths λ=355 nm, 532 nm and 1064 nm. The ion yield, the energy spectrum of the photoelectrons and their angular distributions were measured. The angular distributions at λ=355 nm and λ=532 nm provide a sensitive test for theoretical calculations. Comparison with the calculations available shows that perturbation theory with proper inclusion of atomic structure yields results which agree with experiment. Intensity dependent changes of angular distributions at λ=532 nm are observed, which indicate that at 10¹³ W cm^?2 higher order processes become noticable. At λ=1064 nm the situation is more complicated, experimentally as well as theoretically. Intensities of some 10¹³ W cm^?2 are necessary to observe ionization. Strong distortions of the atomic structure can be expected. Presently only qualitative aspects of the angular distributions can be discussed.     

Studies of Silver Nanoparticles by Laser Ablation Method

The laser ablation technique has been employed to study silver colloidal formation. Laser intensities, irradiation wavelengths (1064 nm and 532 nm), and solvents (water, methanol, and isopropanol) were all considered. Changes of the maximum UV-Visible absorbance of the solutions with laser intensities exhibited nonlinear behavior for 1064 nm and 532 nm and displayed better ablation efficiency at 532 nm. Larger mean sizes were observed at 532 nm or at higher pulse energy. For solvent effect, the bigger particle sizes were generated in H₂O. As to colloidal stability, isopropanol, which has a lower dielectric constant than water, was found to stabilize Ag nanoparticles without protecting reagents over six months. Preliminary results in 2-butanol suggested that the viscosity of solvent may need to be considered in addition to the dielectric constant.     

Conservative restoration of the Augustus Arch of Fano: cleaning methodology as derived from preparatory analyses and sampling

The original appearance of Augustus Arch of Fano was compromised by a diffuse distribution of black scales and other deposits. In order to preserve the stone surface the restoration intervention operated with different cleaning techniques so that it was possible to use every method with a properly and not dangerous intensity. In particular it showed the possibility to use laser cleaning to destroy the external hard part of black scales, and complete the intervention with light chemical cleaning. In the case of Augustus Arch this way resulted useful for preserve signs on surface and cleaning every kind of deposits at the same time. Every intervention on such an important monument need to obtain at the same time the best result for materials conservation and the aim of image restore.     

Study of laser ablation of brass materials using inductively coupled plasma atomic emission spectrometric detection

A XeCl laser and a Q-switched Nd:YAG laser operating at 1064, 532, 355 and 266 nm were used to ablate brass materials with varying concentrations of Zn and Cu. The ablated material was transported to an inductively coupled plasma for further atomization, excitation and ionization with an atomic emission spectrometric detection. A Zn enhancement was observed, which could be suppressed by using a Nd:YAG laser working at 266 nm with fluences higher than 400 J cm⁻² (equivalent to 80 GW cm⁻²). In contrast, a lack of linearity was observed for Cu as a function of the concentration, regardless of the wavelength and the fluence. The Cu problem seemed to occur during the ablation and was related to the structure of the brass material. Lack of linearity was also observed for Zn and other contained elements when samples from different origins were used.     

Influence of laser irradiation on the optical properties of nano-sized powder of metal oxide

ZnO Nano powders were prepared by co-precipitation method which includes post-oxidation and annealing in air. Influence of laser irradiation was carried out using 355 nm laser on the physical properties of ZnO nanoparticles. SEM studies reveal agglomeration of grains resulting into enlargement and deformation of the nanoparticles. XRD pattern exhibited decrease in FWHM which is a clear evidence of the increase in crystallite size due to laser irradiation. Optical properties showed decrease in the band gap of the laser irradiated Nano powders. The observed results indicated the UV laser irradiation increases the ZnO nanoparticles crystallinity that affects the optical properties of the ZnO.     

Novel approach to the microscopic inspection during laser cleaning treatments of artworks

The present work focuses on the potential of 3D digital microscopy for assessing micro-morphological features during laser cleaning treatments of artworks. This application requires preliminary optimization studies aimed at defining operative irradiation parameters and practicable degree of cleaning, as well as in situ diagnostic assessments during the restoration work. To this goal, we developed and tested a dedicated 3D digital microscope by implementing the “shape-from-focus” technique. The significant potential of this instrument, which provides textural and chromatic information, was proven for the phenomenological characterization of black crust removal from stones, earthy concretion from bronzes and dark varnish from easel paintings. Comparative measurements using 3D digital microscopy and contact microprofilometry were performed after laser cleaning tests of prepared samples, genuine archaeological bronze artefacts and a stone sculptural element from Florence’s Dome. The results achieved demonstrate the effectiveness and reliability of the novel approach and the advantages it provides with respect to alternative techniques, which will allow the methods to be used in the wider restoration community.     

Influence of laser wavelength on LIBS diagnostics applied to the analysis of ancient bronzes

In this work the influence of laser wavelength upon the analytical results obtained from applying LIBS diagnostics to bronzes was investigated theoretically and experimentally at 1,064 nm and 355 nm. The laser ablation process was modeled for a set of reference samples of quaternary Cu/Sn/Pb/Zn alloys and the difference between plume composition and known target stoichiometry was estimated for both of the wavelengths considered. LIBS measurements were performed on the same set of reference samples and under the same experimental conditions to validate the model at different wavelengths. Results from the application of the model to calculate sample optical properties during laser irradiation, absorption in the plasma and plasma temperature are also presented.     

On the copper oxide neutral cluster distribution in the gas phase: detection through 355 nm and 193 nm multiphoton and 118 nm single photon ionization

The distribution of neutral copper oxide clusters in the gas phase created by laser ablation is detected and characterized through time-of-flight mass spectroscopy (TOFMS). The neutral copper oxide clusters are ionized by two different approaches: Multiphoton absorption of 355 and 193 nm radiation; and single photon absorption of 118 nm radiation. Based on the observed cluster patterns as a function of experimental conditions (e.g., copper oxide or metal sample, ablation laser power, expansion gas, etc.) and on the width of the TOFMS features, one can uncover the true neutral cluster distribution of CumOn species following laser ablation of the sample. Ablation of a metal sample generates only small neutral CumOn clusters for m less, similar 4 and n approximately 1, 2. Ablation of copper oxide samples generates neutral clusters of the form CumOm (m < or = 4) and CumO(m-1) (m > 4). These clusters are directly detected without fragmentation using single photon, photoionization with 118 nm laser radiation. Using 355 and 193 nm multiphoton ionization, the observed cluster ions are mostly of the form Cu2mOm+ for 4 < or = m < or = 10 (193 nm ionization) and CumO1,2 (355 nm ionization) for copper oxide samples. Neutral cluster fragmentation due to multiphoton processes seems mainly to be of the form CumO(m,m-1) --> CumO(m/2,m/2+1). Neutral cluster growth mechanisms are discussed based on the cluster yield from different samples (e.g., Cu metal, CuO powder, and Cu2O powder).     

Sampling modulation technique in radio-frequency helium glow discharge emission source by use of pulsed laser ablation

An emission excitation source comprising a high-frequency diode-pumped Q-switched Nd:YAG laser and a radio-frequency powered glow discharge lamp is proposed. In this system sample atoms ablated by the laser irradiation are introduced into the lamp chamber and subsequently excited by the helium glow discharge plasma. The pulsed operation of the laser can produce a cyclic variation in the emission intensities of the sample atoms whereas the plasma gas species emit the radiation continuously. The salient feature of the proposed technique is the selective detection of the laser modulation signal from the rest of the continuous background emissions, which can be achieved with the phase sensitive detection of the lock-in amplifier. The arrangement may be used to estimate the emission intensity of the laser ablated atom, free from the interference of other species present in the plasma. The experiments were conducted with a 13.56 MHz radio-frequency (rf) generator operated at 80 W power to produce plasma and the laser at a wavelength of 1064 nm (pulse duration:34 ns, repetition rate:7 kHz and average pulse energy of about 0.36 mJ) was employed for sample ablation. The measurements resulted in almost complete removal of nitrogen molecular bands (N₂⁺ 391.44 nm). Considerable reduction (about 75%) in the emission intensity of a carbon atomic line (C I 193.03 nm) was also observed.     

Controlled release of α-amylase from microchamber arrays containing carbon nanoparticle aggregates

Microchamber arrays have been prepared from a composite of polylactic acid and carbon nanoparticles. Due to the presence of the nanoparticles, the microchambers are sensitive to infrared laser irradiation. α-Amylase has been encapsulated in the microchambers and released under controlled laser irradiation at 1064 nm with retention of the enzyme activity.     

1064nm激光诱导Ge(111)与Cl2反应动力学

采用超声分子束和时间分辨质谱技术研究了1064nm脉冲激光辐照下Ge(111)与Cl₂的反应动力学。实验结果表明,该反应的主要产物为GeCl₂,提高入射氯分子的平动能将增加反应速率。激光能量密度对GeCl₂产率呈指数关系,而对GeCl₂的平动温度影响不大。升高Ge(111)表面温度也能提高反应产率。同时还讨论了近红外激光诱导GeCl₂反应的机理。