Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.     

Biodegradability of poly(3-hydroxybutyrate) film grafted with vinyl acetate: Effect of grafting and saponification

Radiation-induced graft polymerization of vinyl acetate (VAc) onto poly(3-hydroxybutyrate) (PHB) film was carried out. At a degree of grafting higher than 5%, the grafted films (PHB-g-VAc) completely lost the enzymatic degradability that is characteristic of PHB due to the grafted VAc covering the surface of the PHB film. However, the biodegradability of the PHB-g-VAc films was recovered when the films were saponified in alkali solution under optimum conditions. Graft chains of the PHB-g-VAc film reacted selectively to become biodegradable polyvinyl alcohol (PVA). The biodegradability of the saponified PHB-g-VAc film increased rapidly with time.     

Grafting of poly(methyl vinyl ketone) onto aluminum surface

Polymers were grafted on aluminum surfaces in order to modify the chemical and physical properties of the interface. The properly cleaned and activated surface of the aluminum substrate was first "silanized" either with 3-(trimethoxysilyl)propylamine or allyltrimethoxysilane. The grafting was carried out following two methods: (i) by the reaction of preformed poly(methyl vinyl ketone) with the aminosilane-modified surface; and (ii) by polymerization of methyl vinyl ketone with the vinylsilane-modified surface. The modified aluminum surfaces were characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The new surfaces were examined by contact-angle measurements, and determinations of the Lewis basicity.     

Photodegradation of poly(vinyl acetate)

Poly(vinyl acetate) (PVAc) films with different molecular masses were exposed to ultraviolet radiation. The infra-red spectra of all the samples showed a continuous attenuation of the intensity of the carbonyl stretching bands (1740 cm⁻¹) and of the symmetrical methyl bending vibration bands (1375 cm⁻¹), which suggests a steady loss of acetate side groups during irradiation.The electronic spectra showed an increase in the uv absorption at about 272 nm, suggesting the occurrence of polyene sequences in the polymer chains.In the low molecular mass sample there was almost no insoluble gel fraction formed, even after 20 h irradiation; in the high molecular mass polymer there was already a 50% insoluble fraction after 5 h irradiation, indicating a high degree of crosslinking, although the average viscometric molecular mass of the soluble fraction was only about one sixth of the initial value.     

Study of the miscibility of poly(vinyl pyridines) with poly(vinyl acetate), poly(vinyl alcohol) and their copolymers

Miscibility of poly(4-vinyl pyridine) (P4VP) and poly(2-vinyl pyridine) (P2VP) with poly(viny acetate) (PVAc), poly(vinyl alcohol) PVA and poly(vinyl acetate-co-alcohol) (ACA copolymers) has been investigated over a wide composition range. Differentiaal scanning calorimetry (DSC) results indicate that P2VP is immiscible with PVAC, PVA, and their copolymers over the whole composition range. In turn, P4VP appears to be immiscible with PVAC and PVA, but miscible with some ACA copolymers in certain range of composition. The P4VP-ACA phase diagram for different copolymer compositions has been determined. The variation of the glass transition temperature with composition for miscible mixtures was found to follow the Gordon-Taylor equation, with the parameter κ dependent upon copolymer composition. FTIR analysis of blends reveal the existence of specific interactions via hydrogen bonding between hydroxyl groups and the nitrogen of the pyridinic ring, which appear to be decisive for miscibility. © 1994 John Wiley & Sons, Inc.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). I. Crosslinking and crosslinking cleavage of poly(vinyl acetate)

A crosslinked network was formed by the reaction of partially saponified poly(vinyl acetate) and toluylene diisocyanate in benzene. The yield of gel was markedly dependent on the degree of saponification and the concentrations of polymer and diisocyanate. Crosslinked poly(vinyl alcohol) was obtained by treating the poly(vinyl acetate) with a catalytic amount of sodium hydroxide in methanol without any change of the urethane crosslinks. The crosslink based on the urethane linkage was quantitatively cleaved by acids, especially by hydrobromic acid, releasing polymers of the same molecular weight as the original.     

用DSC研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用示差扫描量热法（DSC）研究了线形多嵌段聚氨酯（PU）与聚氯乙烯（PVC）、氯化聚氯乙烯（CPVC）共混相容性，说明了PU／VC、PU／CPVC的相容是由于共混物中形成了新的氢键的缘故．聚酯型聚氨酯与PVC、CPVC的相容性要好子聚酸型聚氨酯，CPVC与PU的相容性又要好于PVC．聚氨酯中硬段的引入不利于PU／PVC、PU／CPVC的相容性．     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). IV. Polymerization of vinyl trimethylacetate in the presence of crosslinked poly(vinyl acetate)

In order to clarify the grafting behavior of vinyl trimethylacetate (VTMAc) onto poly-(vinyl acetate) (PVAc), the polymerization of a radioactive VTMAc in the presence of a crosslinked PVAc gel was studied in accordance with the experimental technique described in the previous papers. It was found that, at 60°C, the grafting onto the main chain of PVAc takes place about 2.8 times as readily as that onto the acetyl side group on PVAc.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.     

Seeded polymerization of vinyl acetate using monodisperse poly(vinyl acetate) latex particles

The seeded polymerizations of vinyl acetate, using monodisperse poly(vinyl acetate) latex particles prepared in the absence of emulsifiers with potassium persulfate, have been investigated at 70°C with potassium persulfate as an initiator. New small particles were formed in the system containing a small amount of seed particles, but were not observed in the system containing a large amount of seed particles. The size of the secondary particles increased, and their number decreased, with an increase in the seed particle number. The minimum diameter of PVAc particles, which are stabilized by the sulfate ion groups bound at the end of polymer chains during polymerization, was determined to be 0.12 μm diameter from the limiting total surface area of seed particles which prevented further secondary nucleation. The minimum diameter of the particles increased as the speed of the stirrer increased. The new small particle number calculated using this value agreed well with that formed in the seeded polymerization.     

Structural relaxation in poly(vinyl acetate)

Structural relaxation in poly(vinyl acetate) (PVAc) in and slightly above the glass-transition region has been studied by monitoring the time dependence of enthalpy using differential scanning calorimetry and the frequency dependence of electric polarization by dielectric loss measurements. The results have been analyzed to yield the kinetic parameters characterizing the structural relaxation and are compared with similar analyses of previously published shear compliance and volume relaxation experiments. Relaxation of enthalpy, electric polarization, volume, and shear stress in PVAc all appear to be characterized by somewhat different relaxation times. The difference between the volume and enthalpy relaxation times, coupled with the fact that PVAc exhibits a Prigogine–Defay ratio greater than unity, is evidence for a previously proposed connection between the thermodynamics and kinetics of structural relaxation in terms of an order parameter model.     

Effect of diluents on poly(vinyl acetate) dynamics

The effect of diluents and temperature on segmental motion in poly(vinyl acetate) was investigated by both NMR and ESR spectroscopy. Three classes of diluents were studied: chloroform, a thermodynamically good solvent; water, a poor solvent which slightly swells the polymer and lowers its glass transition temperature; and decane, a nonsolvent so poor it does not appear to swell the polymer nor lower the calorimetric glass transition temperature. At all temperatures investigated each type of diluent increased the segmental motion of the polymer over that of the bulk sample. Under the conditions studied, ¹³C and ²H NMR and nitroxide spin-label ESR data gave similar views of segmental motion of the polymer, indicating that in this amorphous polymer the segmental motion of the polymer may be safely inferred from spin-label data.     

Electrochemical AFM on surface grafted poly(ferrocenylsilanes)

Ethylenesulfide and trimethylenesulfide end‐functionalized poly(ferrocenyldimethylsilanes) (ES‐PFS and TMS‐PFS) with different degrees of polymerization were prepared via anionic ring‐opening polymerization. Molecular characterization of ES‐PFS was carried out by using ¹H‐NMR, GPC, FTIR, and elemental analysis. Thin films of ES‐PFS were prepared by immersing gold(111) substrates into 1.0 mg/ml solutions of the polymers in toluene. The polymeric films were characterized by FTIR, XPS, and contact angle measurements. Thicknesses of the grafted films were measured by SPR. Thicknesses determined by SPR and the theoretically calculated values are in a reasonable agreement. The morphology of the films was studied by tapping mode AFM. The electrochemical behavior of the films was monitored by cyclic voltammetry (CV). CVs show two reversible redox peaks, indicating a stepwise oxidation of the iron atoms in the polymer chains. Scanning Electrochemical Force Microscopy (SEFM) allowed us to study in situ the morphological changes occurring in the film upon electrochemical oxidation or reduction. AFM images indicated that in the oxidized form the chains were stretched due to electrostatic repulsion.     

Compatibility of binary systems of poly(methyl methacrylate), poly(vinyl chloride) and poly(vinyl acetate)

The influence of the thermal treatment on the stability in time of the dispersion degree of films containing binary polymer mixtures, poly(vinyl chloride)/poly(methyl methacrylate), poly(vinyl chloride)/poly(vinyl acetate) and poly(vinyl acetate)/poly(methyl methacrylate), was studied by thermogravimetry and optical microscopy with phase contrast. The dispersion degree depends particularly on the composition of the polymer mixture and can be improved by thermal treatment at temperatures above the glass temperatures of both homopolymers. It seems that this thermal treatment yields exclusively metastable structures with a general tendency to phase separation in a short time after thermal treatment, the heterogeneity mixtures (as film) being more pronounced.     

Strain birefringence studies on poly(vinyl acetate) networks

Atactic poly(vinyl acetate) prepared in a free-radical polymerization was crosslinked by means of benzoyl peroxide. The resulting elastomeric networks were studied in elongation, both unswollen and swollen with triethylbenzene, over the range 0–90°C. The most important experimental results obtained were values of the network birefringence, which is negative, as was recently also found to be the case for networks of atactic poly(methyl acrylate).Calculations carried out to interpret the birefringence were based on Monte Carlo simulations of the atactic structure, and on the rotational isomeric-state theory of chain configurations. The agreement between theory and experiment was very good, in fact much better than has usually been observed for other polymers studied to date.     

Low-frequency excitations in amorphous poly(vinyl acetate)

Raman-active modes have been detected in amorphous poly(vinyl acetate) in the frequency region 20–160 cm^?1. The low-frequency spectrum appears as a broad band for all three molecular weights examined. Spectra were recorded at two temperatures, 293 and 77 K, and found to show similar characteristics at both temperatures. The presence in solid amorphous polymers of broad structureless bands in general and their significance are discussed.     

Morphology of poly(ethylene oxide)/poly(vinyl acetate) blends

The morphology of poly(ethylene oxide)/poly(vinyl acetate) (PEO/PVAc) blends was examined using small angle X-ray scattering (SAXS) and optical microscopy. The morphological and structural parameters of the blends are dependent on both composition and crystallization conditions. Optical microscopy revealed that blend samples prepared by solution casting crystallized with volume-filling crystals up to a composition of 30/70 wt% PEO/PVAc; at higher PVAc content there was no evidence of crystallization in the temperature range studied. Pure PEO always crystallized with a spherulite-hedrite morphology. The formation of spherulites was relatively favoured at lower crystallization temperatures and by addition of PVAc to PEO. Small angle X-ray intensity profiles were analyzed using a recently developed methodology and it was found that, for a given crystallization temperature, the amorphous and interphase thicknesses increased with increasing PVAc content but that the average crystalline thickness was independent of composition. The morphological and structural properties of the PEO/PVAc blends were attributed to the presence of non-crystallizable material in both the interlamellar and interfibrillar regions.