Selective CO oxidation on a Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst in the surface ignition regime: 1. Fine purification of hydrogen-containing gases

Selective CO oxidation in a mixture simulating the methanol steam reforming product with an air admixture was studied over Ru/Al₂O₃ catalysts in a quasi-adiabatic reactor. On-line monitoring of the gas temperature in the catalyst bed and of the residual CO concentration at different reaction conditions made it possible to observe the ignition and quenching of the catalyst surface, including transitional regimes. A sharp decrease in the residual CO concentration takes place when the reaction passes to the ignition regime. The evolution of the temperature distribution in the catalyst bed in the ignition regime and the specific features of the steady-state and transitional regimes are considered, including the effect of the sample history. In selective CO oxidation and in H₂ oxidation in the absence of CO, the catalyst is deactivated slowly because of ruthenium oxidation. In both reactions, the deactivated catalyst can be reactivated by short-term treatment with hydrogen. A 0.1% Ru/Al₂O₃ catalyst is suggested. In the surface ignition regime, this catalyst can reduce the residual CO concentration from 0.8 vol % to 10–15 ppm at O₂/CO = 1 even in the presence of H₂O and CO₂ (up to ～20 vol %) at a volumetric flow rate of ～100 1 (g Cat)^?1 h^?1, which is one magnitude higher than the flow rates reported for this process in the literature.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Colloidal properties of aqueous dispersions of ultradispersed Al<Subscript>2</Subscript>O<Subscript>3</Subscript> prepared by explosion synthesis

The electrosurface properties of aluminum oxide particles prepared by shock—wave loading of aluminum powder in an oxygen-containing atmosphere and the aggregation stability of its aqueous dispersions are studied by the macroelectrophoresis method, potentiometric titration, and photometry. The enhanced stability of the dispersions in acid media and in the vicinity of the isoelectric point compared to that in alkaline media is explained by the effect of the structural component of the disjoining pressure, which appears due to the predominant hydration of the cationic forms of aluminum that are present on the surface of dispersed phase particles.Translated from Kolloidnyi Zhurnal, Vol. 67, No. 1, 2005, pp. 128–131. Original Russian Text Copyright © 2005 by Chiganova, Nafikova.     

One-pot synthesis of Nb-modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript> support for NiMo hydrodesulfurization catalysts

The effect of Nb as a support modifier on the NiMo₆/Al₂O₃–Nb₂O₅(x) (x?=?0, 1, 4, and 8?wt% Nb) catalysts was studied. The supports were prepared by one-pot coprecipitation from soluble precursors. The XRF analysis of the catalysts showed that the contents of Mo and Ni increased slightly with the presence of Nb. Micropore area and pore volume augmented importantly with Nb content, resulting in pore diameters between 5.3 and 9.3?nm. XPS analysis showed that the presence of Nb decreases the active metal–support interaction, improving the Mo and Ni sulfidation degree. The Raman spectra of sulfided catalysts suggested an increase in the number of layers of MoS₂ in the presence of Nb. Generally, the thiophene HDS activity at normal pressure of sulfided NiMo₆/Al₂O₃–Nb₂O₅(8) was greater than that of the sulfided catalysts with x?=?0, 1, and 4?wt% Nb, which can be attributed to the Nb promotion that would have an effect on the type of active site (Brønsted or Lewis acidic sites), since the number of sites by CO chemisorption for sulfided NiMo₆/Al₂O₃–Nb₂O₅(x) did not show correlation with the catalytic activity. The high-pressure HDS activity of dibenzothiophene was also greater in the presence of Nb, and the hydrogenation route was preferred for the Nb-promoted solid, while the unpromoted one showed a larger yield of direct desulfurization products.

Open image in new window

     

Kinetics and mechanism of carbon monoxide oxidation on the supported metal complex catalyst PdCl<Subscript>2</Subscript>-CuCl<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The kinetics of carbon monoxide oxidation with atmospheric oxygen on a PdCl₂-CuCl₂/γ-Al₂O₃ catalyst was studied at T = 27°C and an N₂-O₂-CO mixture pressure of 1 atm. The catalyst was prepared by cold impregnation. Three groups of mechanistic hypotheses are considered, and two of them are demonstrated to be consistent with kinetic data, although they differ in the roles of water and oxygen in carbon monoxide oxidation.     

An active phase transformation on surface of Ni-Au/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst during partial oxidation of methane to synthesis gas

It was studied the influence of gold addition on physico-chemical properties and catalytic activity of bimetallic Ni-Au/Al₂O₃ catalyst in partial oxidation of methane (POM). The reduction behavior in hydrogen, XRD crystal structure, XPS spectra and POM catalytic activity were investigated. The reduction of Ni-Au catalyst is a prerequisite condition to catalyze POM reaction. The formation of Ni-Au alloy during high temperature reduction in hydrogen and also in the conditions of POM reaction was experimentally proved. The addition of gold to Ni/Al₂O₃ system improves catalyst stability and activity in POM reaction.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Kinetic studies on the hydrogenation of nitrate in water using Rh/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Rh-Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Liquid-phase reduction NO ₃ ⁻ using monometallic and bimetallic catalysts (5% Rh/Al₂O₃, 5% Rh-0.5% Cu/Al₂O₃, 5% Rh-1.5% Cu/Al₂O₃, 5% Rh-5% Cu/Al₂O₃ and a physical mixture of 5% Rh/Al₂O₃ and 1.5% Cu/Al₂O₃) was studied in a slurry reactor operating at atmospheric pressure. Kinetic measurements were performed for a low concentration of nitrate (0.4 × 10⁻³−3.2 × 10⁻³ mol dm⁻³) and the temperature range 293–313 K. From the experimental data, it was found that the reduction of nitrate is first order with respect to nitrate. On the basis of the rate constants, the apparent activation energy was established using a graphic method. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 881–886. This article was submitted by the authors in English.     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Carbon black oxidation mechanism in loose and tight contacts with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript> catalysts

The catalytic combustion of carbon black was investigated in the presence of CeO₂ and Al₂O₃. The influence of contact type between carbon particles and these oxides was examined by thermal analysis, the BET specific area, and EPR spectroscopy. For tight contact carbon black-catalyst mixtures, a new paramagnetic species is observed and can be considered as a fingerprint of the contact between the two solids. These new paramagnetic species increase the reactivity of the catalytic reaction of carbon black (CB) combustion and take part in the oxidation mechanism of CB. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 899–904. This article was submitted by the authors in English.     

Reactivation of CoMo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalysts with chelating agents

Effect of various chelating components, multibasic carboxylic acids and glycols, used to prepare hydrotreating catalysts on the activity regeneration of calcined hydrotreating catalysts was studied. Reactivated catalyst samples were tested in a model reaction of hydrodesulfurization of dibenzothiophene. It was shown that the treatment of calcined catalysts with the chelating components leads to an increase in the catalytic activity. The best catalytic characteristics are observed for the catalyst reactivated with a solution containing citric acid and triethylene glycol.     

Laser-induced luminescence associated with surface hydroxide groups in Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Laser-induced luminescence of OH_s groups for undoped Al₂O₃ oxides of various phase compositions was excited by pulsed nitrogen laser radiation at 337.1 nm. The luminescence band at 500–650 nm assigned to hydroxide groups of Al₂O₃, actually, consists of several lines at 500–515, 553, 567, 577, 607, and 633 nm; these constituent bands can be assigned to various types of OH_s surface groups. In the low-temperature phases of the γ→δ→θ-Al₂O₃ series, excitation at a wavelength of 337.1 nm gave rise to a characteristic luminescence band associated with surface hydroxide groups of Al₂O₃ that appeared at 770 nm.     

The catalytic performance of different promoted iron catalysts on combined supports Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for carbon dioxide hydrogenation

Global warming, fossil fuel depletion and fuel price increases have motivated scientists to search for methods for the storage and reduction of the amount of greenhouse gases, especially CO₂. The hydrogenation process has been introduced as an emerging method of CO₂ capture and convertion into value-added products. In this study, new types of catalysts are introduced for CO₂ hydrogenation and are compared based on catalytic activity and product selectivity. The physical properties of the samples are specified using BET. Iron catalysts supported on γ-Al₂O₃ with different metal promoters (X = Ni, K, Mn, Cu) are prepared through the impregnation method. Moreover, Fe–Ni catalysts supported on HZSM5-Al₂O₃ and Ce–Al₂O₃ are synthesized. Samples are reduced by pure H₂ and involved in hydrogenation reaction in a fixed bed reactor (H₂/CO₂ = 3, total pressure = 10 MPa, temperature = 523 K, GHSV = 2000, 1250 nml/min). All catalysts provide high conversion in hydrogenation reactions and the results illustrate that the selectivity of light hydrocarbons is higher than that of methane and CO. It is found that Ni has a promoting effect on the conversion fluctuations throughout the reaction with 66.13% conversion. Using combined supported catalysts leads to enhancing catalytic performance. When Fe–Ni/γ–Al₂O₃—HZSM5 is utilized, CO₂ conversion is 81.66% and the stability of the Fe–Ni catalyst supported on Al₂O₃ and Ce–Al₂O₃ furthey improves.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Reaction of indoles with ethyl bromopropynoate over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> surface

1H-Indole and 2-methyl-1H-indole reacted with ethyl 3-bromopropynoate over aluminum oxide to give mixtures of the corresponding ethyl 3-(1H-indol-3-yl)propynoates and ethyl 3,3-bis(1H-indol-3-yl)-acrylates, the latter prevailing.     

Thermal stability and surface structure of Mo/CeO<Subscript>2</Subscript> and Ce-doped Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

In order to explore the influence of CeO₂ on the structure and surface characteristics of molybdena, an investigation was undertaken by using N₂ adsorption (BET method), thermal analysis and in-situ diffuse reflectance infrared (DRIFT) techniques. In this work, the Mo/CeO₂ and Ce-Mo/Al₂O₃ samples were prepared by impregnation and co-precipitation methods with high Mo loadings. Combining the results one may notice that the presence of ceria led to the increase of polymerized surface Mo species so as to forming Mo-O-Ce linkages besides the formation of coupled O=Mo=O bonds indicative of polymeric MoO₃. From thermal analysis, it can be inferred that Mo/Al₂O₃ is the thermally most stable material in the temperature range used in the experiment (up to 900°C), whereas Ce-Mo/Al₂O₃ and Mo/CeO₂ samples undergo morphological modifications above 700°C resulting in lattice defects, which motivate the mobility of Mo and Ce ions and thus enhance the possibility of interaction between them. Additionally, their activity towards CO adsorption needs reduced ceria and molybdena containing coordinatively unsaturated sites (CUS), oxygen vacancies and hydroxyl groups to form various carbonate species.     

Oxidative desulfurization of thiophene derivatives with H<Subscript>2</Subscript>O<Subscript>2</Subscript> in the presence of catalysts based on MoO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> under mild conditions

The catalysts based on MoO₃/Al₂O₃ were synthesized and tested using aqueous hydrogen peroxide as the oxidant in the oxidative desulfurization of thiophene, benzothiophene (BT) and dibenzothiophene (DBT) into the corresponding sulfones. Among catalysts tested, 15%(MoO₃–WO₃)/Al₂O₃ prepared by a conventional impregnation method was considerably active for the oxidation of thiophene, BT and DBT, which could achieve higher than 99.2% conversions at lower reaction temperature (≤338 K). The use of hexadecyltrimethyl ammonium bromide as the phase-transfer reagent in small amounts could promote the reaction efficiently.     

Hydrogenolysis of glycerol to propanediols over heteropolyacids promoted AgCu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Various amounts and different types of heteropolyacids promoted 5Ag15Cu/Al₂O₃ catalysts were prepared by impregnation method and analyzed through many techniques. The synthesized catalysts were evaluated for hydrogenolysis of glycerol to propanediols. The results demonstrated that heteropolyacids loading facilitated the reduction, promoted the dispersion, enhanced the acidity, and increased Broensted acid sites of the AgCu catalysts, which benefited the generation of 1,3-propanediol. Compared with phosphotungstic acid and phosphomolybdic acid, silicotungstic acid promoted AgCu catalyst had a better performance for 1,3-propanediol due to the better Cu dispersion and higher Broensted acidity. In addition, when the reaction was performed at 220 °C under 3.5 MPa for 8 h, the chosen 5Ag15Cu-10HSiW/Al₂O₃ achieved a 69.6% glycerol conversion with 35.6% 1,2-propanediol selectivity and 21.5% 1,3-propanediol selectivity.     

Selective catalytic oxidation of ammonia into nitrogen and water vapour over transition metals modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, TiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>

Copper or iron supported on commercially available oxides, such as γ-Al₂O₃, TiO₂ (anatase) and monoclinic tetragonal ZrO₂ (mt-ZrO₂) were tested as catalysts for selective catalytic oxidation of ammonia into nitrogen and water vapour (NH₃-SCO) in the low temperature range. Different commercial oxides were used in this study to determine the influence of the specific surface area, acidic nature of the support and crystalline phases as well as of the type of species and aggregation state of transition metals on the catalytic performance in selective ammonia oxidation. Copper modified oxide supports were found to be more active and selective to nitrogen than catalysts impregnated with iron. Activities of both transition metal modified samples decreased in the following order: mt-ZrO₂, TiO₂ (anatase), γ-Al₂O₃. Quantitative total ammonia conversion was achieved with the Cu/ZrO₂ catalytic system at 400°C. Characterisation techniques, e.g. H₂-temperature programmed reduction, UV-VIS-diffuse reflectance spectroscopy, suggest that easily reducible copper oxide species are important in achieving high catalytic performances at low temperatures.