复合功能布的动态力学性能及本构关系

针对复合功能布的物理特性,利用材料试验机和分离式Hopkinson压杆装置,展开了准静态和动态条件下单层和双层复合功能布材料的单轴抗压实验,获得了两种材料在不同应变率下的应力应变曲线和材料的失效应力、应变.实验结果表明:复合功能布的动态失效强度明显高于准静态失效强度,而且随着应变率的增加其动态失效强度呈现增加的趋势,即该材料具有明显的应变率硬化效应.对应力应变曲线进行拟合,给出了材料的动静态粘弹性本构关系.并对复合功能布在不同应变率下的失效应变及材料的损伤结果进行了初步的分析.     

准一维应变下Al2O3陶瓷动态压缩失效的实验研究

为了考察Al2O3陶瓷准一维应变下的力学性能,采用LY12铝套筒和45钢套筒对陶瓷试样进行了环向约束,在准静态和动态下分别进行了压缩实验,得到了材料的应力-应变曲线。实验结果表明,Al2O3陶瓷的轴向压缩强度基本上随围压的增大而增大,动态压缩加载下的轴向压缩强度随应变率增大而增大。Al2O3陶瓷在准一维应变下的破坏形式为裂纹破坏,准静态的脆性失效行为可以用Mohr-Coulomb失效准则来描述。     

干燥和饱和混凝土动态力学特性及其机理

采用分离式Hopkinson杆装置,对混凝土进行干燥和饱和状态下的SHPB实验,并与准静态实验进行对比。结果表明:干燥和饱和混凝土均具有明显的应变率效应,中等应变率条件下的应力应变曲线上升段比准静态的曲线陡;饱和混凝土动态强度提高的幅度接近干燥混凝土的2倍,具有更强的应变率敏感性;存在一个应变率临界值,仅当应变率大于临界值时,饱和混凝土的动态强度才大于干燥混凝土的的动态强度;基于实验结果,给出了不同饱和度混凝土强度与应变率的关系。     

三种加载方向下云杉静动态力学性能研究

利用INSTRON和Hopkinson压杆对含水率为12.72%, 密度为413kg/m^{3}云杉木材试件沿顺纹、横纹径向和横纹弦向进行准静态和动态压缩实验, 获得了云杉木材3个方向的抗压模量、准静态压缩应力应变曲线和3种应变率下的动态应力应变曲线. 结果表明云杉木材沿顺纹方向加载破坏形式表现为木材纤维轴向屈曲、褶皱; 横纹径向和弦向加载失效行为表现为木材纤维间的滑移破坏. 云杉顺纹方向抗压弹性模量最大, 分别约为横纹径向抗压弹性模量的21倍和横纹弦向抗压弹性模量的32倍; 横纹径向和弦向准静态压缩屈服应力基本相等, 试件沿顺纹方向准静态压缩屈服应力约为横纹径向和弦向屈服应力的9倍; 动态压缩屈服强度具有率敏感性, 在应变率为500-1000s^{-1}动态压缩实验中顺纹、横纹径向和弦向动压屈服强度均随着应变率的增加而显著提高. 同时对不同方向压缩下木材胞壁失效行为进行了理论分析, 表明产生完全压缩失效的平均极限载荷与胞壁屈服强度、胞元结构和产生的褶皱长度相关.      

不同应变率下聚乙烯材料的压缩力学性能

为了研究聚乙烯材料在不同应变率下的压缩力学性能,通过准静态实验和动态实验获得聚乙烯材料不同应变率下的应力应变曲线,分析发现:聚乙烯的弹性模量和屈服强度随应变率增大而增大,具有明显的黏弹塑性;聚乙烯材料进入塑性阶段,其应力应变曲线在不同应变率下具有相近的变化趋势,即塑性切向模量近似相同。根据聚乙烯材料的压缩力学性能,建立了弹性区、屈服点和塑性区的分段本构模型。该模型的屈服点和塑性段与实验结果吻合较好,由于弹性段采用线弹性模型,与实验结果存在一定偏差,可近似描述材料的弹性行为。     

NEPE推进剂低高应变率下改进的黏-超弹本构模型

为研究低高应变率条件下NEPE推进剂的力学特性,通过电子万能试验机和分离式霍普金森杆装置,对NEPE推进剂进行了准静态和冲击实验,得到了不同应变率下（1.667×10?4～4 500 s?1）的应力-应变曲线。实验结果表明NEPE推进剂具有明显的非线性弹性和应变率敏感性,随着应变率的增加,材料的强度、屈服应力和弹性模量显著增加,与低应变率相比,高应变率条件下材料的应变率敏感性更高。在高速冲击下材料内部瞬间产生大量热量无法及时散发出去,使得材料内部温度升高,导致材料出现软化效应,力学性能降低。本文建立了一个非线性黏超弹本构模型,其中采用Rivlin应变能函数来描述稳态超弹响应部分,采用积分型本构模型来描述材料的动态黏弹性响应部分,考虑到松弛时间具有应变率相关性,本文采用了一个率相关松弛函数来替代传统的Prony级数形式。使用极慢速压缩实验数据对本构模型中的超弹部分进行拟合获得超弹参数,然后用准静态和动态实验数据对本构模型进行拟合得出其他参数。不同应变率下的预测曲线与实验曲线具有较好的重合度,证明了该模型可以很好地描述低高应变率下NEPE推进剂的力学特性。     

基于J-C模型的Q235钢的失效准则

使用Instron材料试验机、霍普金森拉杆（SHTB）对Q235钢试件进行了不同温度下的准静态和动态拉伸实验,研究了温度、应变率及应力三轴度对Q235钢失效应变的影响,结果表明:Q235钢失效应变随温度的升高而增加,随应变率的增加而减小,随应力三轴度的增加先减小后增加再减小。基于实验结果对Q235钢J-C失效模型中的温度项进行了修正,并结合数值模拟提出了基于J-C失效模型的应力三轴度三分段式失效准则,通过Taylor撞击实验和数值模拟对给出的模型相关参量进行了验证,实验与模拟结果吻合较好。     

低应变率下硅铝质泡沫陶瓷复合材料的力学性能研究

以泡沫陶瓷复合材料在防护工程中的应用为背景,利用MTS(Material Test System,材料试验机)对该型材料进行了准静态压缩实验。得到了应变率在10-5~10-3s-1范围内的应力应变曲线,并对实验结果进行了理论分析和数值模拟。研究表明,泡沫陶瓷复合材料的力学性能在准静态一维应力压缩条件下显示出明显的应变率效应,同时其应力应变曲线可用一种经验的脆性材料本构模型进行较好地拟合。而在一维应变压缩条件下,材料的应力应变曲线则显示出明显的三段式特征:弹性段、平台段和密实段,同时材料的吸能幅值随着应变率的增大而增加。     

7A04铝合金的本构关系和失效模型

使用万能材料试验机、扭转试验机和Taylor撞击实验研究了高强铝合金7A04在常温至250 ℃的 准静态、动态本构关系和失效模型。基于实验结果,修改了Johnson-Cook强度模型中的应变强化项以及 Johnson-Cook失效模型中的温度软化项,并结合数值模拟标定了模型参数。实验结果表明,7A04铝合金的 应变和应变率强化效应不显著,失效应变随温度的增加、应力三轴度的减小和应变率的减小而增加。     

MDYB-3有机玻璃在不同应变率下的一维屈服行为

对MDYB-3有机玻璃进行了多组不同应变率(10-3~3 000 s-1)下的压缩实验, 得到准静态下的屈服应力与动态下的峰值应力。沿其增强与面内2个方向进行准静态压缩实验, 以分析定向拉伸对屈服应力的影响, 修正了Ree-Eyring模型与Cooperative模型以描述定向有机玻璃的屈服行为。采用Johnson-Cook模型描述屈服后的黏塑性行为。结果表明Cooperative屈服模型比Ree-Eyring屈服模型更接近实验结果, 且能准确描述准静态屈服应力。动态压缩下的峰值应力为失效应力, 说明试样在1 500 s-1以上应变率下未达到屈服应力时已经发生破坏。Johnson-Cook模型对于单条曲线拟合良好, 但无法准确描述材料的应变率相关性。     

The 7th International Conference on Fluid Mechanics May 24-27,2015,Qingdao,China

正http://www.icfm7.org First Announcement and Call for PapersThe objective of International Conference on Fluid Mechanics(ICFM)is to provide a forum for researchers to exchange new ideas and recent advances in the fields of theoretical,experimental,computational Fluid Mechanics as well as interdisciplinary subjects.It was successfully convened by the Chinese Society of Theoretical and Applied Mechanics(CSTAM)in Beijing(1987,     

INFORMATION FOR CONTRIBUTORS

Contributions： The Journal, Acta Mechanica Solida Sinica, is pleased to receive papers from engineers and scientists working in various aspects of solid mechanics. All contributions are subject to critical review prior to acceptance and publication.     

基于鲁棒滤波的捷联导引头视线角速度估计方法

针对捷联导引头无法直接获取视线角速度等信息的问题,研究了鲁棒滤波在大气层外飞行器捷联导引头视线角速度估计中的应用。为了建立非线性滤波估计模型,考虑目标视线角速度的慢变特性,采用一阶马尔科夫模型建立了状态方程;推导了视线角速度的解耦模型,并建立了量测方程;考虑到实际应用中存在系统噪声统计特性失准的问题,基于Huber-Based鲁棒滤波方法,设计了视线角速度滤波器,并完成了基于Huber-Based滤波方法和扩展卡尔曼滤波方法的数学仿真。仿真结果表明Huber-Based滤波方法的视线角、视线角速度及视线角加速度估计精度分别达到0.1140'、0.1423'/s、0.0203'/s2,而扩展卡尔曼滤波方法的视线角、视线角速度及视线角加速度估计精度仅分别为0.6577'、0.6415'/s、0.0979'/s~2。仿真结果证明了该方法可以有效地估计出相对视线角速度等信息,并且在非高斯噪声的条件下,依然可获得较高的估计精度,具有一定的鲁棒性。     

Guide for authors

正Each of the sections below provides essential information for authors.We recommend that you take the time to read them before submitting a contribution to Acta Mechanica Sinica.We hope our guide to authors may help you navigate to the appropriate section.How to prepare a submission This document provides an outline of the editorial process involved in publishing a scientific paper in Acta Mechanica     

Use specification of multiscale materials for life spanned over macro-, micro-, nano-, and pico-scale

Multiscale material intends to enhance the strength and life of mechanical systems by matching the transmitted spatiotemporal energy distribution to the constituents at the different scale, say—macro, micro, nano, and pico,—, depending on the needs. Lower scale entities are, particularly, critical to small size systems. Large structures are less sensitive to microscopic effects. Scale shifting laws will be developed for relating test data from nano-, micro-, and macro-specimens. The benefit of reinforcement at the lower scale constituents needs to be justified at the macroscopic scale. Filling the void and space in regions of high energy density is considered.Material inhomogeneity interacts with specimen size. Their combined effect is non-equilibrium. Energy exchange between the environment and specimen becomes increasingly more significant as the specimen size is reduced. Perturbation of the operational conditions can further aggravate the situation. Scale transitional functions and/or f_j/j+1 are introduced to quantify these characteristics. They are represented, respectively, by , and (f_mi/ma,f_na/mi,f_pi/na). The abbreviations pi, na, mi, and ma refer to pico, nano, micro and macro.Local damage is assumed to initiate at a small scale, grows to a larger scale, and terminate at an even larger scale. The mechanism of energy absorption and dissipation will be introduced to develop a consistent book keeping system. Compaction of mass density for constituents of size 10⁻¹², 10⁻⁹, 10⁻⁶, 10⁻³ m, will be considered. Energy dissipation at all scales must be accounted for. Dissipations at the smaller scale must not only be included but they must abide by the same physical and mathematical interpretation, in order to avoid inconsistencies when making connections with those at the larger scale where dissipations are eminent.Three fundamental Problems I, II, and III are stated. They correspond to the commonly used service conditions. Reference is made to a Representative Tip (RT), the location where energy absorption and dissipation takes place. The RT can be a crack tip or a particle. At the larger size scales, RT can refer to a region. Scale shifting of results from the very small to the very large is needed to identify the benefit of using multiscale materials.     

Impact non-pénétrant sur le thorax : influence de la courbure sur la propagation des ondesNonpenetrating impact on the thorax: influence of curvature on wave propagation

Theoretical studies of the propagation of impact waves through the thorax are needed to improve the design of bulletproof jackets and blast protections (Fung in ‘Biomechanics Motions, Flow, Stress, and Growth’, Springer-Verlag, 1990; Cooper et al., J. Trauma 40 (1996) S38–S41). The influence of the weak acoustic coupling at the interface between the thoracic wall and the lung were described in (Grimal et al., C. R. Acad. Sci. IIB 329 (2001) 655–662); in this work, we study, within the frame of elastodynamics and with an approximate analytical method, the effects of the curvature of this interface. Results are given in terms of strain energy for the pressure wave, transmitted or converted. Focalisation of energy in the medium representing the lung is important for curvatures measured in humans. To cite this article: Q. Grimal et al., C. R. Mecanique 330 (2002) 569–574.     

Vérification expérimentale de la relation de réciprocité d'Onsager pour l'électro-osmose et l'électro-filtration dans une argile naturelleExperimental verification of the Onsager's reciprocal relations for electro-osmosis and electro-filtration phenomena on a saturated clay

This Note is devoted to the experimental verification of the Onsager's reciprocal relations in the particular case of electro-osmosis and electro-filtration. A special set up has been designed to carry out the measurements of both the electro-osmotic permeability and the streaming potential. This has been performed by using a natural material i.e., saturated kaolinite. To cite this article: K. Beddiar et al., C. R. Mecanique 330 (2002) 893–898.