盐引发阴离子/非离子表面活性剂复配体系中囊泡自发形成

在无盐时, 阴离子表面活性剂十二烷基苯磺酸钠(SDBS)与非离子表面活性剂壬基酚聚氧乙烯(10)醚(TX-100)的复配体系中只有混合胶束存在, 而盐的加入即可以引发体系中囊泡的自发形成, 这使得囊泡的形成变得更加简单. 引发机理可以归因于盐对离子表面活性剂的极性头双电层的压缩作用, 减少了极性头的面积, 加上非离子表面活性剂的参与使得堆积参数P增加, 导致了半径更大的聚集体的形成. 制作了SDBS/TX-100/盐水拟三元相图, 通过目测和表面张力的变化确定了囊泡形成的带状区域, 并用负染色电镜(TEM)对囊泡进行了表征, 同时测定了盐度以及相同盐度下表面活性剂浓度对囊泡粒径的影响, 发现囊泡的粒径随着盐度的增加而增加, 而在同一盐度下, 囊泡的粒径基本不受表面活性剂浓度的影响.     

Vesicles Formation Induced by Layered Double Hydroxides in Mixture of Lauryl Sulfonate Betaine and Sodium Dodecyl Benzenesulfonate

This paper reports that structurally positively charged layered double hydroxides (LDHs) nanoparticles induce the vesicle formation in a mixture of a zwitterionic surfactant, lauryl sulfonate betaine (LSB), and an anionic surfactant, sodium dodecyl benzenesulfonate (SDBS). The existence of vesicles was demonstrated by negative‐staining (NS‐TEM) and freeze‐fracture (FF‐TEM) transmission electron microscopy and confocal laser scanning microscopy (CLSM). The size of vesicles increased with the increase of volume ratio (Q) of Mg₃Al‐LDHs sol to the SDBS/LSB solution. A new composite of LDHs nanoparticles encapsulated in vesicles was formed. A possible mechanism of LDHs‐induced vesicle formation was suggested. The positive charged LDHs surface attracted negatively charged micelles or free amphiphilic molecules, which facilitated their aggregation into a bilayer membrane. The bilayer membranes could be closed to form vesicles that have LDHs particles encapsulated. It was also found that an adsorbed compound layer of LSB and SDBS micelles or molecules on the LDHs surface played a key role in the vesicle formation.     

Salinity Controlled Vesicle Formation and Growth in Aqueous Mixture of Aerosol OT/Triton X‐100

Mixed vesicles can be formed spontaneously from aqueous mixture of the double‐tailed anionic surfactant sodium bis(2‐ethylhexyl) sulfosuccinate (AOT) and the nonionic surfactant octylphenoxypolyethoxyethanol (Triton X‐100) under the inducement of salt, the formation mechanism of which should be attributed to the compression of salt on the electric bilayers of the head groups. The stability and the polydispersity of the vesicles are superior to single‐component AOT vesicles, which can be proved by the TEM image and visual observation. The vesicle region was presented in a pseudo‐ternary diagram of AOT/TX‐100/brine. The size of the vesicle was measured using dynamic light scattering. It is found that the vesicle size increases with the salinity but decreases with the content of TX‐100 in the mixture at the same salinity. Especially, the vesicle size is independent of the surfactant concentration at fixed salinity.     

Encapsulation and Releasing of Calcein by Spontaneously Formed Zwitterionic/Anionic Vesicle without Separation

The encapsulation and releasing of fluorescence dye calcein by spontaneously formed vesicle, from the mixtures of anionic surfactant (sodium dodecyl benzene sulfonate) and zwitterionic surfactant (Lauryl sulfonate betaine), was characterized with a simple but sensitive and accurate fluorescence method, using cobalt chloride as a quenching agent. Different from the separation method, the whole process proceeded in the same solution without removing the free calcein. After cobalt chloride quenching the outer calcein, the releasing of the calcein from the vesicle to bulk solution starts and finally reaches a steady value depending on the equilibrium between the osmotic pressure and resistance of membrane. The entrapment quantity of the SDBS/LSB vesicles to the calcein could then be deduced according to the difference of fluorescence intensity before and after the quenching, which varies with the mixing ratios of the two kinds of surfactants. The addition of additives such as salt and especially the polymer (polyvinylpyrrolidone) reduces the releasing velocity by strengthening the bilayers, and increases the encapsulation quantity, even 3times at the most.     

Transition from micelle to vesicle in aqueous mixtures of anionic/zwitterionic surfactants studied by fluorescence, conductivity, and turbidity methods

Vesicles form spontaneously in a aqueous mixture of sodium bis(2-ethylhexyl) sulfosuccinate (Aerosol OT) and lauryl sulfonate betaine (LSB). Different from catanionic vesicles, the formation or disaggregation of such zwitterionic/anionic vesicles may be easily controlled by adjusting the relative amount of LSB and salinity. The participation of LSB reduces the polydispersity of the vesicles and even results in the formation of monodispersed vesicles at a certain salinity. But as LSB exceeds a certain proportion, vesicles cannot form at any concentration and salinity, making convenient the study of the structural transitions. We applied pyrene as a fluorescence probe and monitored the transition among the monomer, micelle, and vesicle through the variation of I(1)/I(3), accompanied by conductivity and turbidity measurements. In LSB solution and LSB-rich mixture, an abrupt change of the ratio of I(1)/I(3) was found in the transition from monomer to micelle with increasing concentration, as well as in the transition from micelle to vesicle with increasing salinity, which shows that a difference of the polarity of the microenvironment between the micelle and the vesicle bilayer resulted from the composition change. But in AOT solution and AOT-rich mixture, only a gradual change in the transition is observed due to the existence of intermediate structures, which have different microenvironments from micelles and vesicles. So the formation of vesicle experiences a process of monomer to premicelle to micelle to bilayer segment with increasing concentration by combining the conductivity method. The ratio of I(1)/I(3) is independent of the vesicle size once formed.     

Photochemical control of molecular assembly formation in a catanionic surfactant system

Photochemical control of vesicle disintegration and reformation in aqueous solution was examined using a mixture of 4-butylazobenzene-4'-(oxyethyl)trimethylammonium bromide (AZTMA) as the photoresponsive cationic surfactant and sodium dodecylbenzenesulfonate (SDBS) as the anionic surfactant. Spontaneous vesicle formation was found in a wide-ranging composition of the trans-AZTMA/SDBS system. AZTMA molecules constituting vesicles underwent reversible trans-cis photoisomerization when irradiated with ultraviolet and visible light. Transmission electron microscopy observations using the freeze-fracture technique (FF-TEM) showed that UV light irradiation caused the vesicles to disintegrate into coarse aggregates and visible light irradiation stimulated the reformation of vesicles (normal control). A detailed investigation of the phase state and the effects of UV and visible light irradiation on the AZTMA/SDBS system with the use of electroconductivity, dynamic/static light scattering, and surface tension measurements and FF-TEM observations revealed that in the AZTMA-rich composition (AZTMA/SDBS 9:1) a micellar solution before light irradiation became a vesicular solution after UV light irradiation and visible light irradiation allowed the return to a micellar solution (reverse control). Thus, we could photochemically control the disintegration (normal control) and reformation (reverse control) of vesicles in the same system.     

可聚合囊泡体系(烯丙基-二甲基-十二烷基溴化胺和十二烷基硫酸钠)在溶液中的盐效应

高稳定的囊泡广泛用于制作生物模型、药物输送以及合成纳米材料的模板。获得高稳定囊泡结构的重要方法之一是用聚合反应固定囊泡结构。作为可聚合囊泡制备的前期基础工作,研究了一种可聚合的囊泡体系：1-丙烯基－2,2,二甲基－十二烷基溴化胺（ADDB）和ADDB与十二烷基磺酸钠（SDS）的等摩尔比混合体系。该囊泡体系即使在高浓度盐水中也能够自发地形成均相的囊泡溶液。在聚合之前,采用动态激光光散射（DLS）、冷冻蚀刻透射电镜（FF-TEM）技术研究了可聚合囊泡的盐效应。DLS测试发现没有盐存在时,囊泡大小为83 nm,盐的浓度增加到250 mmol/L时,囊泡尺寸增大到250 nm。然而继续增大盐浓度到1000 mmol/L, 囊泡尺寸减小到180nm. FF-TEM结果发现盐浓度小于150 mM时, 单个囊泡为70 nm左右,然而明显存在囊泡的絮凝与融合;当盐浓度增加到400 mM时,单个囊泡尺寸减小到20 nm. 因此DLS 观测到囊泡尺寸增大的原因是由于囊泡的絮凝与融合;而尺寸减小的原因是由于在高盐浓度下,盐屏蔽了带电颗粒之间的静电相互作用,在熵增的驱使下,大囊泡变成小囊泡。     

Dynamics of spontaneous vesicle formation in fluorocarbon and hydrocarbon surfactant mixtures

The spontaneous self-assembly of unilamellar vesicles was investigated by means of time-resolved synchrotron small-angle X-ray scattering. The self-assembly process was initiated by rapid mixing of anionic surfactant micelles with either zwitterionic or cationic surfactant micelles in equimolar ratio using a stopped-flow device. For the zwitteranionic systems, transient disklike mixed micelles are observed as structural intermediates prior to the onset of vesiculation. These disklike micelles display an exponential growth law, and above a critical size they close to form unilamellar vesicles. In the catanionic system, the earliest observable structures within the mixing time of 4 ms are unilamellar vesicles. Nevertheless, in both systems a narrow distribution of the vesicle size was observed at the initial stages of their formation. The subsequent evolution of the vesicle size distribution depends on the subtle differences in the bilayer composition and properties.     

Influences of the concentration and the molar ratio of mixed surfactants on the performance of vesicle pseudostationary phase

In our previous work, it was found that the vesicles were formed spontaneously by mixing octyltriethylammonium bromide (C₈NE₃Br) with sodium dodecyl benzene sulfonate (SDBS), and the vesicles have been developed as a pseudostationary phase (PSP) in EKC. In the present work, the effects of the concentration and the molar ratio of cationic to anionic surfactant on the vesicle properties and the performances of vesicle PSP in EKC have been investigated. The aggregates at all mixing ratio were negatively charged regardless of which surfactant surplus. As C₈NE₃Br proportion increased, the microviscosity of the vesicle became larger. With the increase in the total surfactant concentration, the migration time window broadened at the molar ratio of C₈NE₃Br to SDBS of 3:7. Unexpectedly, the window became narrowed at molar ratio of 5:5 and 6:4. However, the methylene selectivity of vesicle PSP at all above‐mentioned molar ratios enhanced as the total surfactant concentration increased, no matter whether the migration time window enlarged or narrowed. It implied that the vesicle PSP at molar ratio of 5:5 and 6:4 made it possible to obtain a better separation in a shorter time. When the total surfactant concentration was fixed at 20 mM, the methylene selectivity of the vesicle PSP of molar ratio of 5:5 was comparable to that of 3:7, but the migration time shortened by a half.     

Fluid mixing in growing microscale vesicles conjugated by surfactant nanotubes

This work addresses novel means for controlled mixing and reaction initiation in biomimetic confined compartments having volume elements in the range of 10(-12) to 10(-15) L. The method is based on mixing fluids using a two-site injection scheme into growing surfactant vesicles. A solid-state injection needle is inserted into a micrometer-sized vesicle (radius 5-25 microm), and by pulling on the needle, we create a nanoscale surfactant channel connecting injection needle and the vesicle. Injection of a solvent A from the needle into the nanotube results in the formation of a growing daughter vesicle at the tip of the needle in which mixing takes place. The growth of the daughter vesicle requires a flow of surfactants in the nanotube that generates a flow of solvent B inside the nanotube which is counterdirectional to the pressure-injected solvent. The volume ratio psi between solvent A and B inside the mixing vesicle was analyzed and found to depend only on geometrical quantities. The majority of fluid injected to the growing daughter vesicle comes from the pressure-based injection, and for a micrometer-sized vesicle it dominates. For the formation of one daughter vesicle (conjugated with a 100-nm radius tube) expanded from 1 to 200 microm in radius, the mixing ratios cover almost 3 orders of magnitude. We show that the system can be expanded to linear strings of nanotube-conjugated vesicles that display exponential dilution. Mixing ratios spanning 6 orders of magnitude were obtained in strings of three nanotube-conjugated micrometer-sized daughter vesicles.     

Equilibrium surface adsorption behavior in complex anionic/nonionic surfactant mixtures

Neutron reflectivity (NR) and small angle neutron scattering (SANS) have been used to investigate the equilibrium surface adsorption behavior and the solution microstructure of mixtures of the anionic surfactant sodium 6-dodecyl benzene-4 sulfonate (SDBS) with the nonionic surfactants monododecyl octaethylene glycol (C12EO8) and monododecyl triiscosaethylene glycol (C12EO23). In the SDBS/C12EO8 and SDBS/C12EO23 solutions, small globular mixed micelles are formed. However, the addition of Ca2+ ions to SDBS/C12EO8 results in a transition to a vesicle phase or a mixed vesicle/micellar phase for SDBS rich compositions. In contrast, this transition hardly exists for the SDBS/C12EO23 mixture, and occurs only in a narrow composition region which is rich in SDBS. The adsorption of the SDBS/C12EO8 mixture at the air-solution interface is in the form of a mixed monolayer, with a composition variation that is not consistent with ideal mixing. In water and in the presence of NaCl, the nonideality can be broadly accounted for by regular solution theory (RST). At solution compositions rich in SDBS, the addition of Ca2+ ions results in the formation of multilayer structures at the interface. The composition range over which multilayer formation exists depends upon the Ca2+ concentration added. In comparison, the addition of a simple monovalent electrolyte, NaCl, at the same ionic strength does not have the same impact upon the adsorption, and the surface structure remains as a monolayer. Correspondingly, in solution, the mixed surfactant aggregates remain as relatively small globular micelles. In the presence of Ca2+ counterions, the variation in surface composition with solution composition is not well described by RST over the entire composition range. Furthermore, the mixing behavior is not strongly correlated with variations in the solution microstructure, as observed in other related systems.     

Stability and Size Control of Reverse Vesicles

The stability and size control of reverse vesicles have been investigated for a sucrose monoalkanoate/hexaethylene glycol hexadecyl ether/decane/water system. The stability is highly dependent on the surfactant mixing ratio, amount of added water, and vesicle size. The size distribution of reverse vesicles produced by simple mixing is very large, but larger vesicles can be removed by means of the extrusion method and reasonably homogeneously size-distributed reverse vesicles can be obtained. If a probe-type ultrasonicator is used, the reverse vesicles obtained are homogeneous and of very small size (50-70 nm in diameter) and they are considered to be of the unilamellar type.     

Silicone nanocapsules templated inside the membranes of catanionic vesicles

A simple and effective way to synthesize hollow silicone resin particles of controlled diameter is presented. The synthesis utilizes catanionic vesicles as templates for the polycondensation/polymerization processes of 1,3,5,7-tetramethylcyclotetrasiloxane (D4H) within their membranes. Two different surfactant systems were used to form the vesicular templates: mixtures of dodecyltrimethylammonium bromide (DTAB) and sodium dodecylbenzenesulfonate (SDBS) in the cationic (the DTAB/SDBS system) or anionic (the SDBS/DTAB system) rich region of the phase diagram. The templates obtained from these surfactant mixtures form spontaneously unilamellar vesicles in aqueous solution. The vesicular templates swell upon addition of D4H, thus increasing their size. The silicone resin was obtained in acid- or base-catalyzed polycondensation and ring-opening polymerization processes of D4H. In the case of the DTAB/SDBS system the formation of a densely cross-linked silicone material with SiO3/2 units allowed the nanocapsules to retain the vesicular shape after removal of the template, whereas in the SDBS/DTAB system, the polymer produces capsules which are too smooth to support surfactant lysis. The morphology of the silicone nanocapsules was analyzed using transmission electron microscopy (TEM) and, in some cases, atomic force microscopy (AFM). TEM and AFM reveal discrete hollow particles with a small amount of linked or aggregated hollow silica shells.     

Effects of salt and temperature on single‐chained cationic surfactant/oligodeoxynucleotide vesicle formation

Recently, we found oligodeoxynucleotide could induce single‐chained cationic surfactant to organize into vesicles. In this article, we will report the effects of NaCl and temperature on the surfactant/oligodeoxynucleotide vesicle formation. A moderate content of NaCl can facilitate vesicle formation and high content of NaCl makes vesicle degraded. The enhanced hydrophobic interaction between surfactant and oligodeoxynucleotide with NaCl plays a key role for facilitating vesicle formation. Moreover, surfactant/oligodeoxynucleotide vesicles tend to aggregate at high temperature and the change is irreversible. However, the presence of NaCl makes this change reversible. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Hydrotropic salt promotes anionic surfactant self-assembly into vesicles and ultralong fibers

Molecular self-assembly has become a versatile approach to create complex and functional nanoarchitectures. In this work, the self-assembly behavior of an anionic surfactant (sodium dodecylbenzene sulfonate, SDBS) and a hydrotropic salt (benzylamine hydrochloride, BzCl) in aqueous solution is investigated. Benzylamine hydrochloride is found to facilitate close packing of surfactants in the aggregates, inducing the structural transformation from SDBS micelles into unilamellar vesicles, and multilamellar vesicles. The multilamellar vesicles can transform into macroscale fibers, which are long enough to be visualized by the naked eye. Particularly, these fibers are robust enough to be conveniently separated from the surfactant solution. The combined effect of non-covalent interactions (e.g., hydrophobic effect, electrostatic attractions, and π-π interactions) is supposed to be responsible for the robustness of these self-assembled aggregates, in which π-π interactions provide the directional driving force for one-dimensional fiber formation.     

Preparation of crystalline gold nanoparticles at the surface of mixed phosphatidylcholine-ionic surfactant vesicles

The formation of gold nanoparticles and the crystal growth at the surface of mixed phosphatidylcholine (PC)-ionic surfactant vesicles was investigated. The PC-bilayer surface was negatively charged by incorporating sodium dodecyl sulfate (SDS) and positively charged by adding hexadecyltrimethylammonium chloride (CTAB). The mass ratio phosphatidylcholine:surfactant was fixed in both cases at 1:1. The gold nanoparticle formation was studied by using transmission electron microscopy (TEM) combined with dynamic light scattering (DLS) and UV-vis absorption spectroscopy. TEM micrographs confirm that the particle formation occurs on the vesicle surface. However, the reduction process depends on the ionic surfactant incorporated into the vesicles, the vesicle size distribution, as well as the temperature used for the reduction process. Thereby, it becomes possible to control the crystal growth of the individual spherical gold nanoparticles in a characteristic way. Red colored colloidal dispersions consisting of monodisperse spherical nanoparticles with an average particle size between 2 and 8 nm (determined by dynamic light scattering) can be obtained by using a monodisperse SDS-modified vesicle phase. When the temperature is increased to 45 degrees C, a crystallization in rod-like or triangular structures is observed. In the CTAB-based template phase in general larger gold particles of about 35 nm are formed. In similarity to the anionic vesicles a temperature increase leads to the crystallization in triangular structures.     

Facilitation effect of oligonucleotide on vesicle formation from single‐chained cationic surfactant—Dependences of oligonucleotide sequence and size and surfactant structure

The interaction between DNA and surfactant has both biological and technological significances. Recently, we reported for the first time that oligo d(C)₂₅ can induce single‐chained cationic surfactant molecules to aggregate into vesicles. In this article, we studied systematically the formation of vesicles from traditional single‐chained cationic surfactant molecules in the presence of a series of oligonucleotides and found that the facilitation efficiency of oligonucleotide on vesicle formation depends on its size and base composition. Oligo d(T)_n cannot induce vesicle formation, whereas the other oligonucleotides can. Moreover, the oligonucleotide with a bigger size or with a hairpin structure favors vesicle formation more, and the increases in the size of the head group and/or the length of the alkyl group of surfactant decrease the facilitation efficiency of oligonucleotide. Since so far, there is very limited report about the vesicle formation in DNA/single‐chained cationic surfactant solution, this study could be expected to increase the efficiency and applicability for DNA/amphiphile system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 434–449, 2009     

阴离子Gemini表面活性剂和阳离子传统表面活性剂混合体系双水相中囊泡形貌的转变

通过电子显微镜观察了阴离子gemini表面活性剂C₁₁- p-PhCNa和阳离子传统表面活性剂DTAB混合体系双水相中囊泡形貌随体系组成和浓度的转变。结果表明,双水相较浓的一相中形成了多层囊泡,囊泡的大小和壁厚随相的组成和浓度而改变,两组分等电荷混合有利于形成较大且壁较厚的囊泡。分析表明, gemini表面活性剂在聚集体中采取的反式构象可能是其容易形成厚壁多层囊泡的重要原因,C₁₁- p-PhCNa联接链上的苯氧基与DTA⁺之间的p-阳离子相互作用以及两组分相反电性头基之间的静电吸引使囊泡壁的多层结构更加稳定。     

Self-assembly of organic-inorganic hybrid amphiphilic surfactants with large polyoxometalates as polar head groups

Mn-Anderson-C6 and Mn-Anderson-C16, A type of inorganic-organic hybrid molecules containing a large anionic polyoxometalate (POM) cluster and two C6 and C16 alkyl chains, respectively, demonstrate amphiphilic surfactant behavior in the mixed solvents of acetonitrile and water. The amphiphilic hybrid molecules can slowly assemble into membrane-like vesicles by using the POM clusters as polar head groups, as studied by laser light scattering and TEM techniques. The hollow vesicles have a typical bilayer structure with the hydrophilic Mn-Anderson cluster facing outside and long hydrophobic alkyl chains staying inside to form the solvent-phobic layer. Due to the rigidity of the POM polar heads, the two alkyl tails have to bend significantly for the vesicle formation, which makes the vesicle formation more difficult compared to some conventional surfactants. This is the first example of using hydrophilic POM macroions as polar head groups for a surfactant system.     

Controlled initiation of enzymatic reactions in micrometer-sized biomimetic compartments

We present a technique to initiate chemical reactions involving few reactants inside micrometer-scale biomimetic vesicles (10(-12) to 10(-15) L) integral to three-dimensional surfactant networks. The shape of these networks is under dynamic control, allowing for transfer and mixing of two or several reactants at will. Specifically, two nanotube-connected vesicles were filled with reactants (substrate and enzyme, respectively) by microinjection. Initially, the vesicles are far apart and any diffusive mixing (on relevant experimental time scales) between the contents of the separated vesicles is hindered because of the narrow diameter and long axial extension of the nanotube. To initiate a reaction, the vesicles were brought close together, the nanotube was consumed by the vesicles and at a critical distance, the nanotube-vesicle junctions were dilated leading to formation of one spherical reactor, and hence mixing of the contents. We demonstrate the concept using a model enzymatic reaction, which yields a fluorescent product (two-step hydrolysis of fluorescein diphosphate by alkaline phosphatase), where product formation was measured as a function of time using a FRAP fluorescence microscopy protocol. By comparing the enzymatic activity with bulk measurements, the enzyme concentration inside the vesicle could be determined. Reactions could be followed for systems having as few as approximately 15 enzyme molecules confined to a reactor vesicle. To describe the experiments we use a simple diffusion-controlled reaction model and solve it using a survival probability approach. The agreement with experiment is qualitative, but the model describes the trends well. It is shown that the model correctly predicts (i) single-exponential decay after a few seconds, and (ii) that the substrate decay constant depends on the number of enzymes and geometry of reaction container. The numerical correction factor Lambda is introduced in order to ensure semiquantitative agreement between experiment and theory. It was shown that this numerical factor depends weakly on vesicle radius and number of enzymes, thus it is sufficient to determine this factor only once in a single calibration measurement.