Internal electrolyte temperatures for polymer and fused-silica capillaries used in capillary electrophoresis

Polymers are important as materials for manufacturing microfluidic devices for electrodriven separations, in which Joule heating is an unavoidable phenomenon. Heating effects were investigated in polymer capillaries using a CE setup. This study is the first step toward the longer-term objective of the study of heating effects occurring in polymeric microfluidic devices. The thermal conductivity of polymers is much smaller than that of fused silica (FS), resulting in less efficient dissipation of heat in polymeric capillaries. This study used conductance measurements as a temperature probe to determine the mean electrolyte temperatures in CE capillaries of different materials. Values for mean electrolyte temperatures in capillaries made of New Generation FluoroPolymer (NGFP), poly-(methylmethacrylate) (PMMA), and poly(ether ether ketone) (PEEK) capillaries were compared with those obtained for FS capillaries. Extrapolation of plots of conductance versus power per unit length (P/L) to zero power was used to obtain conductance values free of Joule heating effects. The ratio of the measured conductance values at different power levels to the conductance at zero power was used to determine the mean temperature of the electrolyte. For each type of capillary material, it was found that the average increase in the mean temperature of the electrolyte (DeltaT(Mean)) was directly proportional to P/L and inversely proportional to the thermal conductivity (lambda) of the capillary material. At 7.5 W/m, values for DeltaT(Mean) for NGFP, PMMA, and PEEK were determined to be 36.6, 33.8, and 30.7 degrees C, respectively. Under identical conditions, DeltaT(Mean) for FS capillaries was 20.4 degrees C.     

Variation of zeta-potential with temperature in fused-silica capillaries used for capillary electrophoresis

The temperature variation of electroosmotic mobility corrected for the effects of Joule heating (muEOF0) was employed to investigate the variation of the zeta-potential (zeta) with temperature in fused-silica capillaries. Experimentally determined values for zeta increased at 0.39% per degrees C, a rate that is about four to five times smaller than reported previously. Experimentally determined values of zeta were directly proportional to the absolute temperature although values were also influenced slightly by changes to the dielectric constant. It was found that the effective charge density at the inner surface of the capillary was independent of temperature.     

Preparation of a sulfonated fused-silica capillary and its application in capillary electrophoresis and electrochromatography

In the present paper, two new methods, sol-gel and chemical bonding methods, were proposed for preparation of sulfonated fused-silica capillaries. In the sol-gel method, a fused-silica capillary was coated with the sol solution obtained by hydrolysis of 3-mercaptopropyltrimethoxysilane (MPTS) and tetramethoxysilane, and followed by age; while in the chemical bonding method, a capillary was chemically bonded directly with MPTS. Then, both the resulting capillaries were oxidized with an aqueous solution of hydrogen peroxide solution (H2O2) (30%, m/m) to obtain the sulfonated capillaries. The electroosmotic flow (EOF) for the sulfonated capillaries was found to remain almost constant within the studied pH range, and greater than that of the uncoated capillary. However, the coating efficiency of the capillary prepared by chemical bonding method was higher than that by sol-gel method, by comparing their magnitude of the EOF, the degree of disguise of the silanol and reproducibility of preparation procedure. The effects of the electrolyte's concentration and the content of methanol (MeOH) on the EOF were also studied. Especially, the study of the apparent pH (pH*) on the EOF in a water-MeOH system was reported. Finally, capillary electrophoretic separation of seven organic acids was achieved within 6.5 min under optimal condition using the chemically bonded sulfonated capillary. Moreover, separation of four alkaloids on the sulfonated capillary was compared with that on uncoated capillary in different conditions. Ion-exchange mechanism was found to play a key role for separation of these four basic analytes on the sulfonated capillary.     

Immobilization of phospholipid-avidin on fused-silica capillaries for chiral separation in open-tubular capillary electrochromatography

Phospholipid-coated fused-silica capillaries with immobilized avidin were applied in the chiral separation of D,L-tryptophan, D,L-PTH-serine, and D,L-PTH-threonine at pH 7.4 by open-tubular CEC. Liposomes prepared from 1,2-dipalmitoyl-sn-glycero-3-phosphocholine, 1,2-dipalmitoyl-sn-glycero-3-phosphoethanolamine-N-(Cap biotinyl), or 1,2-dipalmitoyl-sn-glycero-3-phosphoethanolamine-N-(Biotinyl) with different amounts of phosphatidylserine were assessed as phospholipid coating materials. The stability of the coating and the success of the coating procedure were evaluated in terms of the repeatability of the enantiomer migration times and the resolution of enantiomers. The coating procedure itself significantly affected the migration times and resolution of the enantiomers. Reliable chiral separations with high separation efficiencies were achieved through careful choice of the coating method.     

Butyl acrylate porous polymer monoliths in fused-silica capillaries for use in capillary electrochromatography

Capillary electrochromatography incorporates features of both capillary electrophoresis and liquid chromatography. Butyl acrylate polymers, cast in-situ with heat initiated polymerization and no retaining frits have been made. Van Deemter plots of chrysene have been examined at a variety of operating temperatures to examine column behavior. Hmin moves to faster flow-rates and increases slightly in magnitude as temperature is increased. The longevity and reproducibility of the columns have been examined with a homologous series. Performance is very reproducible between two different columns of different diameters, operated on different systems and prepared from the same polymeriation batch. The relative standard deviation of retention factors is a maximum of 3.1% with most values calculated at less than 1%. The uniformity of the polymers as a function of length has also been studied with a series of polycyclic aromatic hydrocarbons, and the columns have proved to be very uniform across their length as measured by the consistency of retention factors with a maximum relative standard deviation of 3.4% and most values calculated between 1 and 2%. Plate numbers of between 65000 and 80000 plates/m have been attained for compounds with retention factors of 3 to 12. These columns have proved easy to make, are quite reproducible, and long lived.     

Joule heating in packed capillaries used in capillary electrochromatography

Effective heat dissipation is critical for reproducible and efficient separations in electrically driven separation systems. Flow rate, retention kinetics, and analyte diffusion rates are some of the characteristics that are affected by variation in the temperature of the mobile phase inside the column. In this study, we examine the issue of Joule heating in packed capillary columns used in capillary electrochromatography (CEC). As almost all commonly used CEC packings are poor thermal conductors, it is assumed that the packing particles do not conduct heat and heat transfer is solely through the mobile phase flowing through the system. The electrical conductivity of various mobile phases was measured at different temperatures by a conductivity meter and the temperature coefficient for each mobile phase was calculated. This was followed by measurement of the electrical current at several applied voltages to calculate the conductivity of the solution within the column as a function of the applied voltage. An overall increase in the conductivity is attributed to Joule heating within the column, while a constant conductivity means good heat dissipation. A plot of conductivity versus applied voltage was used as the indicator of poor heat dissipation. Using theories that have been proposed earlier for modeling of Joule heating effects in capillary electrophoresis (CE), we estimated the temperature within CEC columns. Under mobile and stationary phase conditions typically used in CEC, heat dissipation was found to be not always efficient. Elevated temperatures within the columns in excess of 23 degrees C above ambient temperature were calculated for packed columns, and about 35 degrees C for an open column, under a given set of conditions. The results agree with recently published experimental findings with nuclear magnetic resonance (NMR) thermometry, and Raman spectroscopic measurements.     

Free solution capillary electrophoresis of proteins using untreated fused-silica capillaries.

Numerous efforts have been made to separate proteins by capillary zone electrophoresis (CZE). The most common optimization techniques are changing the pH of the running buffer, coating the capillary surface with a hydrophilic polymer, or using additives in the sample solution. Surface coatings and solution additives can reduce the adsorption of the protein onto the capillary surface, but they diminish the separation efficiency and the resolution of CZE. This paper reports the successful separation of proteins in a untreated fused-silica capillary by raising the pH of the running buffer and washing between runs with 1.0 M sodium hydroxide. Under these conditions, model proteins and proteins in human serum have been determined by CZE. It is shown that the results from CZE are compatible with those of sodium dodecyl sulphate-polyacrylamide gel electrophoresis.     

Novel polyamine coating providing non-covalent deactivation and reversed electroosmotic flow of fused-silica capillaries for capillary electrophoresis

A new polycationic coating for use in capillary electrophoresis has been developed that enables chemical modification of fused-silica capillary surfaces for analysis of compounds like basic proteins. The cationic polyamine, containing short aliphatic blocks of combined 2 and 3-carbon length, was physically adsorbed onto the negatively charged fused-silica surface through ionic interaction by flushing the capillary with a polyamine solution, followed by a self-stabilization step. The polyamine coated capillaries generated an anodal electroosmotic flow that was independent of pH in the investigated range of pH 4-8. The capillary performance was demonstrated by fast separations of basic proteins with peak efficiencies in the range of 265,000-584,000 plates.     

Carbon nanotubes in capillary electrophoresis, capillary electrochromatography and microchip electrophoresis

Carbon nanotubes are among the plethora of novel nanostructures developed since the 1980s. Nanotubes have attracted considerable interest by the scientific community thanks to their extraordinary physical and chemical properties. Research areas have flourished in recent years and now include the nano-electronic, (bio)sensor and analytical field along with many others. This review covers applications of carbon nanotubes in capillary electrophoresis, capillary electrochromatography and microchip electrophoresis. First, carbon nanotubes and a range of electrophoretic techniques are briefly introduced and key references are mentioned. Next, a comprehensive survey of achievements in the field is presented and critically assessed. The merits and downsides of carbon nanotube addition to the various capillary electrophoretic modes are addressed. The different schemes for fabricating electrochromatographic stationary phases based on carbon nanotubes are discussed. Finally, some future perspectives are offered.      

Overview of capillary electrophoresis and capillary electrochromatography.

This paper provides an overview on the current status of capillary electrophoresis (CE) and capillary electrochromatography (CEC). The focus is largely on the current application areas of CE where routine methods are now in place. These application areas include the analysis of DNA, clinical and forensic samples, carbohydrates, inorganic anions and metal ions, pharmaceuticals, enantiomeric species and proteins and peptides. More specific areas such the determination of physical properties, microchip CE and instrumentation developments are also covered. The application, advantages and limitations of CEC are covered. Recent review articles and textbooks are frequently cited to provide readers with a source of information regarding pioneering work and theoretical treatments.     

Stationary phases for capillary electrophoresis and capillary electrochromatography

An overview of the most recent developments in column technology employed in capillary electrophoresis (CE) and capillary electrochromatography (CEC), mainly for the separation of small molecules and ions, is presented. Particular emphasis is laid on permanent coating. The wall modification methods in CE include covalent modification, adsorbed coatings and polymeric coatings, while those in CEC include packed columns, open-tubular columns and fritless columns. A short discussion on the characterization and selectivity of the bonded phases is also given.     

Recent advances in capillary electrophoresis and capillary electrochromatography of pollutants

Recent advances in capillary electrophoresis (CE) and capillary electrochromatography (CEC) separation, detection and sample preparation methodologies applied for the determination of a variety of pollutants is overviewed. The reviewed literature illustrates the wide range of CE applications, indicating the continuing interest in CE and CEC in the environmental field.     

Recent advances in capillary electrophoresis and capillary electrochromatography of pollutants

Recent advances in the CE and CEC separation, detection, and sample preparation methodologies applied to the determination of a variety of compounds having current or potential environmental relevance have been overviewed. The reviewed literature has illustrated the wide range of CE applications, indicating the continuing interest in CE and CEC in the environmental field.     

Recent advances in capillary electrophoresis and capillary electrochromatography of pollutants

An overview of major developments in capillary electrophoresis and capillary electrochromatography systems in the environmental field is presented, covering relevant publications between the second half of 1999 and early 2001. Contributions are reviewed in relation to developments in detection, sample preparation/preconcentration, precision and applications. Many interesting examples are shown and the influence of important parameters on the performance of developed methods is discussed.     

Recent developments in capillary electrophoresis and capillary electrochromatography of carbohydrate species

This review article is concerned with the recent developments in capillary electrophoresis (CE) and capillary electrochromatography (CEC) of carbohydrates. The literature shows that CE possesses impressive potential in the analysis of carbohydrates. On the other hand, CEC has just started to show promise in the analysis of carbohydrates. Advances in separation and detection approaches of derivatized and underivatized carbohydrates are discussed based on the available literature. In addition, important applications are illustrated.     

Titanium dioxide coated surfaces for capillary electrophoresis and capillary electrochromatography

The potential of titanium dioxide coatings to control the electroosmotic flow and to affect the migration behavior of analytes in capillary electrophoresis and open-tubular capillary electrochromatography was evaluated. The inner wall of a fused-silica capillary was applied with a solution of a titanium peroxo complex, followed by heating at an elevated temperature. The resultant product was ascertained to be titanium dioxide in a crystalline form of anatase by the results of Fourier transform-infrared spectrometry (FT-IR), X-ray photoelectron spectroscopy, and Raman spectroscopy. The capillary thus made had anodic or cathodic electroosmotic flow, depending on the pH and composition of the background electrolyte used. The titanium dioxide surface of the capillary was readily modified by a silanizing reagent. The performance of the titanium dioxide surfaces with or without chemical modifications was examined with inorganic anions, neutral compounds and peptides.     

Capillary electrophoresis and capillary electrochromatography of organic pollutants

Capillary electrophoresis (CE) has a unique capability for separation of analytes of environmental concern, particularly those that are more polar and ionic, based on the complementary separation principle of electrophoresis. In the past few years, CE has been selectively used to analyze various classes of compounds having current or potential environmental relevance. This review outlines the current status of CE for the determination of environmental pollutants, based predominantly on research results published from the beginning of 1997 to early 1999. Covered are environmental pollutants of all types except pesticides and inorganics. Certain naturally produced toxins are also covered because of their significant impacts upon human health and the environment. CE methods, as with all methods, must be judged on their ability to provide approaches that are reliable, sensitive, selective, and rapid, while meeting "green chemistry" initiatives for pollution prevention. We also compare CE methods to benchmark environmental techniques involving gas chromatography-mass spectrometry (GC-MS), liquid chromatography-mass spectrometry (LC-MS), and high performance liquid chromatography (HPLC).