Gold electrodes from recordable CDs for mercury quantification by flow injection analysis

The development of a new methodology for the construction of very efficient flow cells for mercury detection by potentiometric stripping analysis, employing the thin gold layer of recordable CDs as working electrode is reported. This new source of electrodes (CDtrodes) show very attractive performance, similar to that obtained with commercial gold electrodes, with superior versatility. The low cost of this new source of "gold electrodes" allows a frequent replacement of the electrode, avoiding cumbersome clean-up treatments. Various experimental parameters have been optimized to yield low detection limits (0.25 ng/mL of mercury for 5 min deposition at 0.3 V) and good precision (standard deviation of 1.9% was obtained for 15 repetitive measurements using 10 ng/mL of mercury). Standard curves were found to be linear over the range of 0.5-100 microg L(-1) of mercury. The flow cells developed were used for the quantification of mercury in oceanic and tap water.     

Gold electrodes from recordable CDs for mercury quantification by flow injection analysis

The development of a new methodology for the construction of very efficient flow cells for mercury detection by potentiometric stripping analysis, employing the thin gold layer of recordable CDs as working ¶electrode is reported. This new source of electrodes (CDtrodes) show very attractive performance, similar to that obtained with commercial gold electrodes, with superior versatility. The low cost of this new source of “gold electrodes” allows a frequent replacement of the electrode, avoiding cumbersome clean-up treatments. Various experimental parameters have been optimized to yield low detection limits (0.25 ng/mL of mercury for 5 min deposition at 0.3 V) and good precision (standard deviation of 1.9% was obtained for 15 repetitive measurements using 10 ng/mL of mercury). Standard curves were found to be linear over the range of 0.5–100 μg L^–1 of mercury. The flow cells developed were used for the quantification of mercury in oceanic and tap water.     

Surface Microreliefs and Voltage–Current Characteristics of Gold Electrodes and Modified Thick-Film Graphite-Containing Electrodes

The surface microreliefs and voltage–current characteristics of gold electrodes and modified thick-film graphite-containing electrodes were studied. The relationship between the formation of an analytical signal of mercury(II) and the surface microrelief was determined. It was found that the surface of a modified graphite-containing electrode is a self-organizing ensemble of microelectrodes.     

Differential-pulse anodic stripping voltammetry of mercury with gold-film micro-electrodes

Cylindrical gold film micro-electrodes are easily produced by plasma-sputtering of gold onto carbon fiber electrodes. The micro-electrodes produced were found to maintain their cylindrical geometry indefinitely, unlike gold wire electrodes of similar dimensions. Application of these electrodes in differential-pulse anodic stripping voltammetry provides a method for quantifying trace levels of mercury(II). Up to 100 μg l^?1 Hg(II) the area of the mercury stripping peak varied linearly with mercury concentration; the detection limit was 3.7 μg l^?1. With more than 100 μg l^?1 Hg(II) a new mercury stripping peak grows in at less positive potentials; its peak height is linear with Hg(II) concentration.     

Effect of the modification of mercuric oxide on the properties of mercury films at HgO-modified carbon paste electrodes

The influence of modifications of the mercuric oxide on the voltammetric properties of mercury film carbon paste electrodes was studied. The mercury film was formed electrochemically from the bulk red or yellow mercuric oxide-modified carbon paste electrodes. Differential pulse anodic stripping voltammetry and optical microscopy in polarised light were used to characterise the properties of the mercury films. The results were compared with those obtained using the conventional preparation of mercury-plated carbon paste electrodes when the mercury film is deposited on the surface of the electrode by reduction of Hg(II) ions in solution utilising a sufficient negative potential. It was shown that the mercury film formed from the yellow modification of the mercuric oxide provides better voltammetric characteristics than the red one owing to the high distribution of its small particles, i.e. the mercury droplets after electrochemical treatment. Such a mercury film has similar properties to those of a mercury film generated from solution. Received: 06 December 1999 / Accepted: 16 March 2000     

铜锌超氧化物歧化酶(Cu2Zn2SOD)在汞电极上的吸附研究

金属氧化还原蛋白质的电化学行为作为生物电化学领域中一个重要的研究内容,受到了广泛的关注犤1～3犦,生物体系一些重要的反应均与基本电荷运动有关,如生物催化、神经传导、光合作用以及呼吸作用等均涉及到一些重要氧化还原蛋白质的氧化还原过程。利用电化学的基本原理和实验方法,不但能在生命体系和有机组织的整体水平上,更主要是能在分子和细胞水平上研究氧化还原蛋白质体系中的电子转移以及氧化态转化的化学本质和规律。铜锌超氧化物歧化酶(Cu2Zn2SOD)是一个二聚体,由两个等同的亚单位组成,每一个亚单位含有咪唑桥联的铜?和锌?离子,催…     

Advantages of using a mercury coated, micro-wire, electrode in adsorptive cathodic stripping voltammetry

A mercury coated, gold, micro-wire electrode is used here for the determination of iron in seawater by catalytic cathodic stripping voltammetry (CSV) with a limit of detection of 0.1 nM Fe at a 60 s adsorption time. It was found that the electrode surface is stable for extended periods of analyses (at least five days) and that it is reactivated by briefly (2 s) applying a negative potential prior to each scan. Advantages of this electrode over mercury drop electrodes are that metallic mercury use is eliminated and that it can be readily used for flow analysis. This is demonstrated here by the determination of iron in seawater by continuous flow analysis. It is likely that this method can be extended to other elements. Experiments using bismuth coated, carbon fibre, electrodes showed that the bismuth catalyses the oxidation of the important oxidants bromate and hydrogen peroxide, which makes it impossible to use bismuth based electrodes for catalytic CSV involving these oxidants. For this reason mercury coated electrodes retain a major advantage for catalytic voltammetric analyses.     

Potentiometric Determination of Mercury with Iodide-Selective Electrodes

The conditions for the application of commercial Radelkis OR-I-7111-D (Hungary) and Crytur 53–17 (Czech Republic) iodide-selective electrodes to the determination of mercury were found. A procedure for the direct potentiometric determination of mercury in industrial products and anthropogenic chemical wastes was proposed.     

Comparison of Mercury Vapor Pressure of Silver Amalgam-Based Electrode Materials Using AAS

Nowadays, several amalgam-based electrodes are commonly used in electrochemistry as a less toxic alternative to mercury electrodes. Therefore, a comparison of the mercury vapor pressure of several silver amalgam-based electrode materials with the mercury vapor pressure of liquid mercury and of dental amalgam using AAS was done in this study. Method was optimized to get the highest mercury signal. Results showed that the mercury vapor pressure of amalgam-based electrode materials not containing liquid mercury is far lower than the mercury vapor pressure of liquid mercury (about two orders of signal magnitude) and comparable with mercury vapor pressure of dental amalgam.     

Simultaneous determination of cadmium(II), lead(II) and copper(II) by using a screen-printed electrode modified with mercury nano-droplets

We are presenting a strategy for the fabrication of disposable screen-printed electrodes modified with mercury nano-droplets and capable of sensing heavy metal ions. They were prepared by coating electrodes with a mixture of multi-walled carbon nanotubes and chitosan, this followed by adsorption of mercury. The resulting sensor was characterized by cyclic voltammetry and impedance spectroscopy. Also the effects caused by adsorption of mercury were investigated. It is shown that square wave anodic stripping voltammetry enables simultaneous determination of cadmium(II), lead(II) and copper(II), for which detection limits of 12, 23 and 20 nM, respectively, are found. Relative standard deviations for ten determinations at 0.6 µM concentrations of these ions are in the range of 3.0 to 5.7%. The applicability was tested by analyzing river water and showed recoveries between 94.1 and 104.6%, thus demonstrating its utility for in-field monitoring of these heavy metal ions.     

General characteristics of the copper-based mercury film electrode

The optimum conditions for the preparation, storage, conditioning and renewal of copper-based mercury film electrodes (CBMFEs) are given. The voltammetric results obtained at these electrodes are compared with the predictions of the theory of cyclic and stripping voltammetry at the mercury film electrode, as well as with the results obtained at the silver-based and the platinum-based mercury film electrodes. The advantage of a CBMFE is prolonged life-time, whereas the disadvantages ar the decreased range of usable positive potentials and the possibility of interfering reactions of the electrodeposited metals with the copper substrate or copper dissolved in the mercury phase. The presence of copper has no essential influence on the behaviour of lead and thallium; it affects the behaviour of zinc markedly and that of cadmium and indium slightly. The conditions allowing the minimization of the harmful action of copper on the behaviour of cadmium and indium have been found.     

Nafion-coated mercury thin film electrodes for batch-injection analysis with anodic stripping voltammetry

Batch-injection analysis exhibits the advantages of rapid and simple electroanalysis of microlitre samples. Nafion-coated mercury thin film electrodes have been evaluated for use in batch-injection analysis with anodic stripping voltammetry (BIA-ASV). The advantages of Nafion-coated electrodes in reducing electrode contamination by components of complex matrices are combined with the analysis of small microlitre sample volumes. The measurement of traces of lead and cadmium is used to illustrate the approach. An optimised procedure for formation of Nafion-coated mercury thin film electrodes is evolved. The relative sensitivity for BIA-ASV at electrodes with and without Nafion coatings is 0.9 and 0.8 for cadmium and lead respectively; detection limits are 2 x 10(-9) M and 4 x 10(-9) M. Studies were done concerning the influence of surfactants and their effect was found to be much less with the Nafion film coating. Applications to real environmental samples are demonstrated.     

Stripping Potentiometry of Lead,Cadmium and Copper at a Nafion Coated Glassy Carbon Electrode with Encapsulated Mercury Acetate

Abstract

The stripping potentiometric determination of lead, cadmium and copper with mercury film glassy-carbon electrodes coated with a Nafion membrane was investigated. The mercury film was plated using either mercury(II) acetate encapsulated within the Nafion membrane or a mercury(II) solution. Dissolved dioxygen was used as the stripping agent. The electrodes showed promising properties, particularly robustness and response repeatability. A linear dependence of the stripping time on concentration was found in the μg l^?1 concentration range (s.d. of intercept ≤ 0.3 μg l^?1, r.s.d. of slope ≤ 1%, for both lead and cadmium).     

Preconcentration and voltammetric measurement of mercury with a crown-ether modified carbon-paste electrode

Carbon-paste electrodes modified with crown-ethers were constructed by mixing the crown-ethers into a graphite powder/Nujol oil matrix. The electrodes so formed were able to bind mercuric ions chemically, and gave greater voltammetric response to mercury than that of ordinary carbon-paste electrodes. The response was characterized with respect to paste composition, crown-ether, preconcentration period, mercury concentration, reproducibility, possible interferences, and other variables. Best results were obtained with 18-crown-6 and an acetate buffer (pH 4.0). The electrode gave good linearity for 1 x 10(-5)-6 x 10(-6)M mercury, a detection limit of 2 x 10(-6)M, and a relative standard deviation of 11%. The investigation may lead to a new class of modified (complexing) electrodes, with different patterns of reactivity.     

Silver based mercury film electrode: Part II. The influence of aging of electrode on the electrode processes of various metal ions

The cyclic voltammetric behaviour of 8 metal ions at solid silver amalgam electrodes prepared by aging of a thin silver based mercury film electrode (SBMFE) and by deposition of silver and mercury on platinum were investigated. It was established that such electrodes behave in relation to some metals (Pb, Bi, Sn) similarly as silver electrodes i.e. the cyclic curves obtained with these electrodes at concentration 10^?3M range show a prepeak-postpeak system corresponding to deposition and dissolution of the monolayer of deposit. On the other hand under the same conditions no prepeaks were observed for cadmium, zinc and thallium. In all cases investigated the heights of anodic stripping peaks were lower on curves obtained with aged SBMFE than on those obtained with fresh SBMFE having a mercury layer 1 μm thick.     

Electroreduction of some pyridine carboxamides on carbon electrodes in aqueous solutions

The electroreductions of the NAD⁺ model compounds nicotinamide (I), N₁-methyl nicotinamide (II), N′-methyl nicotinamide (III) and isonicotinamide (IV) on carbon electrodes have been studied in aqueous media in the pH range 0–12 by linear-sweep cyclic voltammetry (Scheme 1, I-IV). Logarithmic analyses of the reduction peaks were performed by computing the convolution of the current with time as a function of the potential. On the basis of the experimental results it was concluded that the irreversibility of the electron transfers increased when a glassy carbon electrode was used, and this irreversibility being more marked when a plastic formed carbon electrode was employed. The reduction processes occurred with more difficulty on carbon electrodes than on mercury electrodes. Both the reduction and the reoxidation (when occurred) processes changed with respect to those observed on mercury electrodes, being irreversible electron transfers the rate-determining steps in most cases. Thus, for compounds I, II and III at pH < 2 the reductions occurred by the uptake of two electrons and two H⁺ ions, and the rate determining step was found to be the first one-electron transfer, for I and III, and the irreversible second electron transfer, preceded by the uptake of an H+ ion, for II. At pH>3 the processes consisted of electrodimerization reactions, preceded by the protonation of the heterocyclic nitrogen in cases I and III. The second electron transfer of the electroreduction of IV always appeared irreversible, in contrast with that found for mercury electrodes.     

Behaviour of Ion Selective Electrodes Based on Silver or Mercuric Sulfide Selenide and Telluride Matrices

Abstract

The analytical behaviour of solid state, ion-selective electrodes based on silver or mercury sulfide, selenide, or telluride matrices was studied. As the active component, the chalcogenides of Cu, Pb, Cd, Zn, Ni, Co, and Bi for the cation electrodes and silver or mercurous halides for the anion electrodes were included. It was found that all possible combinations of matrix compounds are suitable for the preparation of the electrodes, silver being superior to mercury in respect to redox sensitivity. Prepared Ag⁺, Hg²⁺, Pb²⁺, Cu²⁺ and Cd²⁺ electrodes performed well, whereas Zn²⁺, Ni²⁺, Co³⁺ and Bi³⁺ electrodes showed unsatisfactory performances. Anion-selective electrodes constructed from mercuric chalcogenide-mercurous halide were more sensitive than those made from silver chalcogenide-silver halide system. The performance characteristics of all electrodes are described in terms of sensitivities, selectivities, response times, stabilities, reproducibilities, effect of pH and redox potential.     

The effects of CopperZinc and CopperCadmium intermetallic compounds in different systems used for anodic stripping voltammetry

The CuZn intermetallic compound resulting from simultaneous deposition of copper and zinc at a hanging mercury drop electrode (HMDE) and at preformed mercury film electrodes (MFE) has been studied. Goals were to determine what conditions can be used to avoid intermetallic compound formation and to reduce errors that result from the method of standard additions. For Cu²⁺ and Zn²⁺ concentrations in the ng ml⁻¹ range, the use of shortened preconcentration times in conjunction with a differential pulse stripping waveform and the HMDE show significant reduction in the extent of the interference. The CuCd interference was also characterized at performed MFE's and at MFE's deposited in situ from 5–300 μg ml⁻¹ mercury(II) solutions. No significant interference with the cadmium stripping were was observed with preformed MFE's, but peak depression was observed when the electrodes were deposited in situ. The degree of interference was found to decrease with both increased mercury(II) concentrationa and decreased copper(II) concentration. Errors in the standard addition method are minimal when the copper(II) concentration is not significantly altered.     

Polarography��past, present, and future

Polarography was first developed as an automated method of voltage-controlled electrolysis with dropping mercury electrode. The spontaneously renewed pure electrode surface provided reproducible electrochemical results which enabled scientists to work out adequate theory and rich analytical applications. The original method was then instrumentally modified in various ways. Later, hanging mercury drop was added as an alternative indicator electrode??in this way, polarography turned formally into voltammetry with mercury drop electrodes. Beside, in potential-controlled electrolysis, the mercury drop electrodes have been also used in current-controlled electrolysis (chronopotentiometry)??there, it has provided new experimental effects. Polarography has thus gradually covered a wide field of electrolytic methods based on the use of mercury electrodes, in which it continues developing.     

Mercury-coated platinum microelectrodes for steady-state voltammetry in aqueous solutions at high temperature

Sphere-cap mercury microelectrodes fabricated on a platinum disk substrate were tested in aqueous solutions over the temperature range 295–353 K. The performance of these electrodes was assessed in solutions containing Ru(NH₃)₆Cl₃ and LiClO₄ as supporting electrolyte. From the steady-state limiting current obtained at three different mercury microelectrodes, the diffusion coefficient of the electroactive species at different temperatures was determined. It was found that the diffusion coefficient values were consistent with the Stokes–Einstein and activation energy models. The results obtained also allowed us to conclude that sphere-cap mercury microelectrodes can be useful for elevated temperature electroanalysis in aqueous solutions.