四(4-三甲铵苯基)卟啉荧光熄灭法测定痕量镉(Ⅱ)

利用TPPS₄催化动力学荧光测定痕量镉(Ⅱ)已有报道^[1],而利用四(4-三甲铵苯基)卟啉(TAPP)的荧光熄灭测定痕量镉(Ⅱ)的工作尚未见报道.本文研究了室温下Cd(Ⅱ)-TAPP反应体系的荧光光谱特性,发现Cd(Ⅱ)-TAPP的形成使TAPP的荧光发生静态熄灭.利用咪唑(Imid)、十二烷基硫酸钠(SDS)和乙醇增敏、增稳,最低可检测3×10^-4ppmCd(Ⅱ),灵敏度高于其它方法^[2].测定了胶印锌片和人发中的镉,结果与标准值或方法对照值吻合.     

Bioanalysis of Naproxen by High Performance Reversed Phase Liquid Chromatography with Photometric and Fluorimetric Detection

Abstract

Methods for the quantitative determination of NAPROXEN and its main metabolite in plasma and urine are described. The separation is based on reversed phase liquid chromatography with LiChrosorb RP 8 (5 μm) as the support and methanol/phosphate buffer pH 7 as mobile phase, in some cases with addition of tetrabutyl ammonium ion as ion-pairing agent to improve the chromatographic selectivity. With UV-detector and a simple filter fluorometer an extraction-evaporation procedure is used for both plasma and urine determinations, while the high selectivity and sensitivity of a sophisticated fluorescence detector permits the direct injection of diluted samples on to the column. Use of an internal standard improves the within-run precision (s_rel%), which for plasma determinations of NAPROXEN are - with UV-detection, 0.2 – 1.7% (range 10 – 40 μg/ml), with filter fluorometer, 2.4 – 5.9% (range 12 – 58 μg/ml), and with fluorescence detector, 0.8 – 4.1% (range 5 – 20 μg/ml).     

Determination of enantiomeric excess by capillary electrophoresis

Capillary electrophoresis (CE) is becoming an established method for the determination of chiral trace impurities. This paper provides an overview of the state of the art of CE for such determinations. Detection limits of 0.1% impurity is widely accepted as a minimum requirement for chiral trace impurity determinations. This can be relatively easily achieved with CE. However, determination of lower concentrations requires careful optimization of the separation system. Four factors that are of particular significance for trace enantiomeric determinations: resolution, limit of detection, linear range and type of detection, are discussed. Further, the advantages and disadvantages of derivatization in this context are treated as well as the separation approach, ie., direct chiral separation or separation after the formation of diastereomers. It is concluded that the limit of impurity detection can be about 0.05% when UV detection is employed. Using laser-induced fluorescence detection, a quantitative determination at the 0.005% level is often possible.     

Organic analysis by luminescence methods

This review presents the major features of luminescence methods relating to the estimation of organic compounds in solution. A notation for reporting fluorimetric determinations is proposed. The outstanding factors affecting the fluorescence of solutions are briefly reviewed, and determinations of compounds offering a native fluorescence are illustrated by selected examples. Special attention is paid to functional fluorimetry and to the determination of non-fluorescent compounds by means of chemical reactions giving rise to fluorescent species. Some enzymatic reactions are described, as far as they allow the estimation of definite chemicals. Phosphorimetry and chemiluminescence are exemplified. An appendix presents some new functional fluorimetric determinations developed by the authors.     

表面活性剂存在下铽-镥(钆、钇)-乙酰水杨酸共发荧光体系的研究

本文研究了镥等三种稀土离子与铽-乙酰水杨酸配合物产生的共发荧光效应。在最佳条件下,Lu³⁺、Gd³⁺、Y³⁺的存在可使铽-乙酰水杨酸配合物的荧光分别增强108,58和73倍。讨论了共发光体系的形成条件和荧光特性。利用Tb-Lu-乙酰水杨酸体系和Tb-Lu-乙酰水杨酸-乙二胺四乙酸-十六烷基三甲基溴化铵体系分析了合成稀土样品和包头稀土标准氧化物中的铽,结果满意,加标回收率为90.5～105.6%,并对共发光的机理和表面活性剂的作用进行了初步探讨。     

铝(Ⅲ)-桑色素-十二烷基硫酸钠体系在滤纸基质的荧光反应研究及其分析应用

本文探讨了在滤纸基质上表面活性剂SLS对铝-桑色素荧光反应的增敏作用及最佳实验条件。铝含量在0～6.0ng范围的工作曲线呈良好的线性关系(r=0.9998),方法的检测限为0.001ng。含铝4.0ng的溶液11次测定结果的相对标准偏差为4.3％。方法用于含铝水样的测定获得满意结果,回收率为96.0～100.5％。     

Development of a pulsed-laser,fiber-optic-based fluorimeter: determination of fluorescence decay times of polycyclic aromatic hydrocarbons in sea water

A fiber-optic-based system for remote measurement of time-resolved fluorescence emission spectra is described and characterized. A pulsed nitrogen laser is used to induce fluorescence and a time-gated, one-dimensional photodiode array is used to measure the decay of the fluorescence emission spectra. The results compare favorably with reported values for well characterized compounds having fluorescence decay times in the range 4–50 ns. The potential of using time-resolved fluorimetry (TRF) over fiber-optic cables as a means of improving the specificity of remote fluorescence determinations of spectrally similar polycyclic aromatic hydrocarbons in sea water is demonstrated.     

Determination of molybdenum and cobalt in hydrodesulfurization catalysts using a computerized radioisotope x-ray fluorescence system

A rapid, non-destructive method is presented for the determination molybdenum and cobalt in hydrodesulfurization catalysts employing a PDP-11/05 computer-base radioisotope x-ray fluorescence technique. Precision for molybdenum and cobalt better than 2.5% and 4.0%, respectively, are achieved in 100 sec of fluorescent time. The values obtained by this method are in agreement with values from atomic absorption and neutron activation methods. Besides being nondestructive, only about 50 mg of sample is needed, and no time-consuming acid dissolution is required as in atomic absorption and colorimetric methods. The results for six different commercial catalysts are compared with determinations by atomic absorption, neutron activation analysis methods as well as an x-ray fluorescence system with manual calculations of the percentage of molybdenum and cobalt.     

Simultaneous determination of sixteen major and minor elements in river sediments by energy-dispersive x-ray fluorescence spectrometry after fusion in lithium tetraborate glass

Fluvial sediments, including the NBS SRM-1645 Standard River Sediment, were fused in lithium tetraborate to form glass discs on which determinations of 16 elements (K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr and Pb) were obtained simultaneously at a single set of x-ray conditions by energy-dispersive x-ray fluorescence spectrometry (e.d.x.r.f.). Relatively high sample-to-flux ratios of 1:3 were employed to obtained determinations of several minor as well as major elements on a single disc. Lower sample concentrations 1:6 and 1:10 were also used with the NBS SRM-1645. Inter-element corrections for absorption by iron were significant for detectable elements heavier than iron. In the NBS SRM-1645 samples, corrections were made for the fluorescence of chromium by the Fe K lines as well as the absorption of the Fe K lines by chromium. A background correction was also necessary for manganese in NBS SRM-1645. At the lowest sample-to-flux ratio (1:10) good agreement was obtained between the e.d.x.r.f. determinations and the NBS values for all quantifiable elements except zinc. At higher sample-to-flux ratios, agreement with the NBS values was generally poorer with increasing sample concentration. The relative standard deviation (RSD) of the eight quantifiable major and minor elements (K, Ca, Ti, Mn, Fe, Zn, Sr and Zr) determined under a single set of x-ray conditions ranged from 2 to 9% (RSD) with a mean RSD of 4.4% for a set of replica discs fused with Lake Pueblo/Arkansas River sediment samples.     

Simultaneous determination of metals in two-component mixtures with 5-sulfo-8-quinolinol by using phase-resolved fluorimetry

Determinations of metals in two-component mixtures are described in which 5-sulfo-8-quinolinol is used to produce fluorescent chelates of the metals. The metal chelates have broad, overlapping fluorescence spectra but the fluorescence lifetimes (τ) of the chelates are sufficiently different to permit phase-resolved fluorimetric determinations in which the fluorescence contributions of the two chelates can be resolved. Average determination errors ranged from ?4.1% to 2.1% for each metal chelate in mixtures of zinc and cadmium (Δτ = 1.0 ns), gallium and indium (Δτ = 1.7 ns) and aluminum and gallium (Δτ = 5.3 ns). Limits of detection and determination for each individual metal chelate were found to be three times and five times greater, respectively, for the phase-resolved measurements relative to steady-state measurements under the same experimental conditions. Effects of pH on the fluorescence lifetimes and intesities of the metal chelates were studied.     

Determination of Mercury by Nondispersive Atomic Fluorescence Spectrometry

A nondispersive atomic fluorescence spectrometer for the determination of mercury by the cold-vapor technique has been developed. The conditions for mercury vapor generation in a hydride generator (the concentration and volume of the reagents, reaction and purge times, and argon flow rate) are optimized for fluorescence measurements. An algorithm is proposed for the calculation of the analytical signal that leads to an increase in the signal-to-noise ratio by a factor of 3 as compared to the conventional procedure. On the basis of the results obtained, procedures for the determination of mercury in soil and semolina samples are developed with a detection limit of 60 pg and RSD = 10%. The accuracy of the determinations is verified by an analysis of standard reference samples of soil and semolina.     

富硒酵母中硒的连续浸提原子荧光法形态分析

采用连续浸提、氢化物发生一原子荧光法测定研究了富硒酵母中硒的赋存形态。结果表明,富硒酵母中不同形态的硒所占比例从高到低顺序为：碱溶态,水溶态,盐溶态,醇溶态,残渣态;酵母硒中有机态硒达78％以上,主要以碱溶态形式存在。     

X-ray fluorescence determination of total sulfur in fly ash

Standard addition, double dilution and standard calibration were used for x-ray fluorescence (XRF) determinations of sulfur in fly ashes. Samples were analysed as pellets prepared by mixing with acrylate copolymer or with microcrystalline cellulose (in the case of the double dilution method). Lithium sulfate was used for the standard addition method and also as standard with known sulfur content for the double dilution method. Fly ashes analysed by optical emission spectrometry with an inductively coupled plasma (ICP-OES) were used as standards for the standard calibration XRF method. Sulfur was determined in the range of ca. 10^–1–10⁰ % S. For the fly ashes from the North-Bohemian brown coals, the differences between the XRF determinations and the ICP-OES determinations ranged from ca. 1.4 to 10% rel. and precision (repeatability) was better than 10% (RSD). The standard calibration method is suitable for routine analyses of real samples of similar nature. The methods of standard addition and double dilution are rather laborious in sample preparation compared with the standard calibration. Received: 27 October 1998 / Revised: 5 March 1999 / Accepted: 11 March 1999     

Determination of Rb and Sr concentrations in rocks by radioisotope X-ray fluorescence analysis

A method is described for Rb and Sr concentration determinations in rocks by radioisotope X-ray fluorescence analysis. The yield/concentration ratios were established by increasing the concentrations of the examined elements in the sample and recording each spectrum. The analytical error in the 100-1,000 ppm concentration range was 2–4%, and for 50 ppm about 10%, and the detection limit was 5–10 ppm.     

Wavelength-modulated,continuum-source excited atomic fluorescence spectrometric system for wear metals in jet engine lubricating oils using electrothermal atomization

A system for measuring atomic fluorescence of atoms produced via an electrically-heated graphite filament in a flame (acetylene/air or acetylene/nitrous oxide) and excited with a 300-W Eimac xenon are lamp is described. The experimental system also included wavelength modulation for background emission/fluorescence/scatter correction and an optically-triggered electronic integrator for efficient monitoring of the analyte fluorescence signal. Copper, aluminum and molybdenum were determined in jet engine lubricating oil samples (1 μl) with no pretreatment. The determinations are evaluated with respect to the accuracy and repeatability criteria of the U.S. Joint Oil Analysis Program.     

Laser-induced low-temperature fluorescence spectroscopy

The absorption and fluorescence spectra of molecules are often very sharp under cryogenic sampling conditions. When a tunable laser is used to excite fluorescence, selective determinations of individual constituents of very complex samples are possible, and the highly resolved fluorescence spectra can serve as 'molecular fingerprints'     

Fluorimetric determination of trace amounts of aluminium and gallium with salicylaldehyde-1-phthalazinohydrazone

Fluorimetric determinations of aluminium and gallium, based on the formation of fluorescence complexes between Al(III) or Ga(III) and salicylaldehyde-1-phthalazinohydrazone, SAPhH, are proposed. The Al(III)-SAPhH complex exhibits fluorescence with maximum emission at 475 nm when excited at 414 nm; the Ga(III)-SAPhH chelate has emission and excitation maxima at 480 and 410 nm, respectively. For both determinations the range of application is 10–100 ng/ml. Aluminium has been determined in waters, and gallium in aluminium and nickel alloys.     

High selective determination iron(II) by its enhancement effect on the fluorescence of pyrene-tetramethylpiperidinyl (TEMPO) as a spin fluorescence probe

A novel fluorescence method determination for iron(II) with a high selectivity and sensitivity has been proposed, based on the enhancement of fluorescence signals resulting from specific redox reaction between synthesized spin fluorescence probe pyrene-tetramethylpiperidinyl (TEMPO) and iron(II). Under the experimental conditions, fluorescent probe displayed a rapid and linear response for iron(II) over the concentration range from 2.4 x 10(-7) to 3.6 x 10(-6) mol/L. The limit of detection was 4.0 x 10(-8) mol/L. The relative standard deviation of six replicate measurements was 1.90% for 3.0 x 10(-7) mol/L iron(II). Because of the specific redox reaction between developed spin fluorescence probe and iron(II), there are few interference by other ions, especially in the presence of relative high concentration iron(III). The method has been successfully applied for iron(II) determinations in two different kinds of real samples. Results determined by the proposed method agree favorably with those determined UV-vis spectrometry method with 1,10-phenanthroline.     

A Fluorescence Spot Test for Salicylate Determination

Abstract

A procedure based on a spot test for salicylate is presented. The method is simple, rugged and is based on the salycilate native fluorescence measurement on the surface of a filter paper by using optical fibers for light conduction. The fluorescence was linear at concentration range of 0.01–0.4 mmol l^?1. The relative standard deviation of 5% (n=10) was observed. Detection and quantification limits were 4 and 14 µmol l^?1, respectively. The results obtained in pharmaceutical salicylate determinations showed that practically no statistical difference existed with the pharmacopeical method (95% confidence level). The recovery studies in biological samples spiked with salicylic acid at overdose concentration levels showed that the matrix sample did not interfere in the method.     

Rapid determination of total sulfur in fuels using gas chromatography with atomic emission detection

The purpose of this study is to determine whether gas chromatography (GC)-atomic emission detection (AED) can be used in a low-resolution mode for rapid, accurate determinations of total sulfur in fuels at trace levels to complement other popular methods of total sulfur analysis. A method for the rapid determination of total sulfur in fuels (called "fast GC-AED") is developed. The method is tested on gasoline, jet fuel, kerosene, and diesel fuel with sulfur concentrations ranging from 125 mg/L down to 2.5 mg/L. Fast GC-AED shows better performance than traditional GC-AED for total sulfur determinations, especially for complex mixtures containing many different sulfur-containing compounds at trace levels. This method also shows that GC-AED can be used for both rapid determinations of total sulfur and traditional determinations of speciated sulfur without requiring equipment changes. Fast GC-AED is competitive with other popular methods for sulfur analysis. The 5-min program that is developed for fast GC-AED is comparable with the time scale of other methods, such as wavelength dispersive X-ray fluorescence and UV-fluorescence (2 to 5 min). Fast GC-AED also compares favorably with UV-fluorescence for trace sulfur determinations, demonstrating accuracy down to 2.5-mg/L sulfur.