Design and characterization of a fiber optic-based fluorimeter

The design and preliminary charaterization of a novel fiber optic-based fluorimeter are reported. It includes a white light source, optical fibers for light transmission and an intensified photodiode array for detection. A bifurcated sensing configuration is used to transmit excitation and emission radiation to and from the analyte solution. Detection limits in the nanomolar range are reported for several test compounds.     

Impedimetric immunosensor using avidin-biotin for antibody immobilization

A newly developed electrochemical method--Elimination Voltammetry with Linear Scan (EVLS)--has been applied to the electrochemical study of nucleic acids (NAs) on a silver electrode. Using the linear combination of the currents measured at different scan rates, the EVLS is capable of eliminating one or two selected particular currents. It was shown that the elimination function conserving the reversible diffusion current and eliminating the charging and kinetic currents provides the significant increase of voltammetric signals of DNA. Due to the high sensitivity and resolution power, the EVLS can contribute to study behaviour of nucleic acids on the charged interface and can be applied to nucleic acid analyses and the development of DNA sensors.     

Oriented antibody immobilization for atrazine determination by a flow-through fluoroimmunosensor

An atrazine flow-through fluoroimmunosensor was developed, based on an oriented antibody covalently bound to Protein-A (Prot-A) immobilized on Controlled Pore Glass (CPG). Atrazine was detected “in-situ” by placing the immobilized antibody in the optical path of the flow cell. Immobilization of 30 μg of polyclonal anti-atrazine antibody on 0.5 g of Prot-A-CPG provided the highest sensitivity. The effect of several solvents on the covalently immobilized antibodies regeneration was evaluated, the optimum conditions being achieved by pumping 5% acetonitrile (pH = 3) at 0.15 mL/min for 100 s. The detection limit of the immunosensor was 0.7 μg/L and the reproducibility was 2% and 4% for 5 μg/L and 40 μg/L, respectively, in the optimum working concentration range (0.7–50 μg/L). This device allowed 12 samples per hour to be analyzed and had a life-time of 200 assays. Simazine and desisopropylatrazine (DIA) were not cross-reactive, desethylatrazine (DEA) has a cross-reactivity of 8% and propazine and prometryn of 44% and 27%, respectively. The immunosensor was applied to the determination of atrazine in tap and ground water samples spiked at the ?10 and 30 μg/L concentration level. Received: 30 April 1999 / Revised: 16 July 1999 / Accepted: 21 July 1999     

Oriented antibody immobilization for atrazine determination by a flow-through fluoroimmunosensor

An atrazine flow-through fluoroimmunosensor was developed, based on an oriented antibody covalently bound to Protein-A (Prot-A) immobilized on Controlled Pore Glass (CPG). Atrazine was detected “in-situ” by placing the immobilized antibody in the optical path of the flow cell. Immobilization of 30 μg of polyclonal anti-atrazine antibody on 0.5 g of Prot-A-CPG provided the highest sensitivity. The effect of several solvents on the covalently immobilized antibodies regeneration was evaluated, the optimum conditions being achieved by pumping 5% acetonitrile (pH = 3) at 0.15 mL/min for 100 s. The detection limit of the immunosensor was 0.7 μg/L and the reproducibility was 2% and 4% for 5 μg/L and 40 μg/L, respectively, in the optimum working concentration range (0.7–50 μg/L). This device allowed 12 samples per hour to be analyzed and had a life-time of 200 assays. Simazine and desisopropylatrazine (DIA) were not cross-reactive, desethylatrazine (DEA) has a cross-reactivity of 8% and propazine and prometryn of 44% and 27%, respectively. The immunosensor was applied to the determination of atrazine in tap and ground water samples spiked at the ¶10 and 30 μg/L concentration level.     

Hapten immobilization for antibody sensing using a dynamic modification protocol

Optical fiber (OF) sensors are often limited by the immobilization technique used to associate a specific sensing ligand with the OF surface. This is particularly true when the ligand is biologically active as, for example, in the case of immobilized haptens or antibodies. The dynamic modification protocol is a regenerable and experimentally simple way to immobilize a variety of sensing molecules on an OF surface. Furthermore, the protocol is immune to hydrolysis and not limited by diffusion through a membrane or sol–gel. In this publication the approach is extended by immobilizing the hydrophobic hapten (octadecyl 6-(2,4 dinitrophenyl)aminohexanoic acid) as a means to prepare an OF sensor for antibodies specific for 2,4 dinitrophenyl (DNP). The LOD for anti-DNP is 0.5 nanomolar and the K_apparent is 1.0±0.2×10⁶. Nonspecific antibody adsorption is problematic in this sensing approach and was found to limit the quantitative capabilities of the sensor. However, time discrimination can be used to allow the nonspecific antibody to desorb prior to measurement thus minimizing the influence of nonspecific binding on sensor performance.     

Novel hollow fiber immobilization techniques for whole cells and advanced bioreactors

A novel microporous hollow fiber membrane-based immobilization technique for whole cells has been developed. Yeast cells (Saccharomyces cerevisiae) were grown on chopped hydrophobic microporous hollow fibers as well as on hydrophilic hollow fibers. This immobilization support was used to carry out fermentation in a tubular bioreactor. Air was passed from time to time to facilitate cell growth. The microbial culture reached a very high cell density level of around 10¹⁰/mL of fiber lumen volume. An ethanol concentration of 45 g/L and productivity of 41 g/L-h were obtained with an initial glucose concentration of 100 g/L. The present technique does not have the shortcomings of conventional immobilization methods.     

Permanently oriented antibody immobilization for digoxin determination with a flow-through fluoroimmunosensor

This paper reports a new flow-through fluoroimmunosensor, the function of which is based on antibodies immobilized on an inmunoreactor of controlled-pore glass (CPG), for determination of digoxin, used in the treatment of congestive heart failure and artery disease. The immunosensor has a detection limit of 1.20 microg L(-1) and provides high reproducibility (RSD=4.5% for a concentration of 0.0025 mg L(-1), and RSD=6.7% for 0.01 mg L(-1)). The optimum working concentration range was found to be 1.2 x 10(-3)-4.0 x 10(-2) mg L(-1). The lifetime of the immunosensor was about 50 immunoassays; if stored unused its lifetime can be extended to three months. A sample speed of about 10-12 samples per hour can be attained. Possible interference from substances with structures similar to digoxin (morphine, heroin, tebaine, codeine, pentazocine and narcotine) was investigated. No cross-reactivity was seen at the highest digoxin: interferent ratio studied (1:100). The proposed fluoroimmunosensor was successfully used to determine digoxin concentrations in human serum samples.     

Improving immunobinding using oriented immobilization of an oxidized antibody

Recent technical advances in biorecognition engineering and microparticle fabrication enabled us to develop a single-step purification process using magnetic particles (MPs). The process is simple, efficacious, easy to automate, and economical. The method immobilizes the ligand molecule in a particular orientation on commercial MPs that have surface carboxyl groups. Mouse IgG and anti-mouse IgG antibody were the model capture and ligand molecules for this study. The immunobinding efficacy of anti-mouse IgG antibody using "oriented immobilization" was compared with the efficacy of a conventional amine-coupling system that results in random orientation and of another standard method, the biotin-streptavidin system. The oriented immobilization was accomplished by oxidizing the sugar moiety in the CH(2) domain of the antibody's Fc and covalently conjugating the moiety to the hydrazine-coated MP. The specific binding affinity of the oriented immobilization process was about 2.5 times that of the amine-coupling system, and selectivity from a binary mixture was about 2 times greater for the oriented immobilization method. Results were nearly identical for the biotin-streptavidin system and the oriented immobilization system, matching the calculated binding stoichiometry between mouse IgG and anti-mouse IgG antibody. The binding improvement over the amine-coupling system shown by assay was confirmed by a separate surface plasmon resonance experiment. In summary, the oriented immobilization method was as effective as the streptavidin-biotin system, yet simpler and cost-effective.     

Surface modification of polyacrylonitrile fiber for immobilization of antibodies and detection of analyte

Pendent nitrile groups of multifilamentous polyacrylonitrile (PAN) fibers were reduced to amino groups using lithium aluminum hydride for different time of reduction and amine content was estimated by performing acid-base titrations. Attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR) and Differential Scanning Calorimetry (DSC) were used for the characterization of the generated amino groups and thermal properties of the reduced fibers, respectively. The surface morphology of the fibers after reduction and immobilization was characterized using Scanning Electron Microscope (SEM). The newly formed amino groups of the fibers were activated by using glutaraldehyde for the covalent linking of Goat anti-Rabbit IgG-HRP (GAR-HRP) antibody enzyme conjugate. Modified PAN fibers were evaluated as a matrix for sandwich ELISA by using Goat anti-Rabbit antibody (GAR-IgG), Rabbit anti-Goat (RAG-IgG) as analyte and enzyme conjugate GAR-HRP. The fibers reduced for 24 h were able to detect the analyte RAG-IgG at a concentration as low as 3.75 ng mL⁻¹ with 12% skimmed milk as blocking reagent for the optimized concentration of primary antibody GAR-IgG 3 μg mL⁻¹ and peroxidase conjugate GAR-HRP dilution of 8000 fold. The sensitivity, specificity and reproducibility of the developed immunoassay was further established with antibodies present in human blood using Rabbit anti-Human (RAH-IgG) antibody and the corresponding HRP enzyme conjugate. As low as 0.1 μL of human blood was sufficient to perform the assay with the modified fibers.     

On-line pre-concentration of atrazine by antibody immobilization capillary electrophoresis

Antibody coupled capillary electrophoresis was employed in the pre-concentration and detection of atrazine at the parts per billion (ppb) level. A 1000-fold increase in detection has been demonstrated in the use of IgG anti-atrazine monoclonal antibodies for the analysis of atrazine in well water by capillary zone electrophoresis (CZE) with UV-VIS detection. These results were confirmed by an enzyme linked immunosorbent assay (ELISA) specific for atrazine.     

Evaluation of supports and methods for immobilization of enzyme cyclodextringlycosyltransferase

An experimental design with factorial planning was used for the immobilization of the enzyme cyclodextringlycosyltransferase (CGTase) from Bacillus firmus (strain no.37) to select the best combination of support, method of immobilization, and conditions that gives primarily higher average values for the specific immobilized enzyme activity, and secondarily, higher average values for the percentage of protein fixation. The experimental design factors were as follows: supports—controlled-pore silica, chitosan, and alumina; immobilization methods—adsorption, and two covalent bonding methods, either with γ-aminopropyltriethoxysilane or hexamethylenediamine (HEMDA); conditions—7°C without agitation and 26°C with stirring. The best combination of factors that lead to higher average values of the response variables was obtained with immobilization of CGTase in silica with HEMDA at 7°C. However, immobilization in chitosan at 7°C gave the highest immobilized CGTase specific activity, 0.25 μmole of β-CD/(min·mg protein). Physical adsorption gave low specific enzyme activities, and, in general, a high load of enzyme leads to lower specific enzyme activity.     

Selection and optimization of monoclonal antibody immobilization procedure for its use in IRMA

Immobilization of monoclonal antibody (McAb) on polystyrene support is an integral part of any immunoassay (IA) procedure. Two different immobilization approaches (direct and indirect) were evaluated for their effectiveness. In case of direct immobilization, mouse monoclonal antibody was adsorbed ‘passively’ on polystyrene tubes. The same antibody was immobilized as ‘pre-formed complex’ in case of indirect approach via mouse IgG as linker. Both the approaches displayed comparable Bmax using different buffer systems. However, NSB observed via mouse IgG linker was always on the higher side (0.8–4.0 %). This could be significantly reduced (up to <0.4 %) by controlling the concentration of mouse IgG.Theoretical advantages envisaged via indirect approach viz. economy and stability of immobilized antibody were similar to that of simple passive adsorption. Hence, we have selected simple passive adsorption method using bicarbonate buffer (pH 8.4). Our study also confirmed the need for ‘tube maturation’ in order to retain the immunological integrity of the immobilized antibody. The performance of the tubes prepared by direct immobilization method was evaluated in an immunoradiometric assay for human Luteinizing hormone (LH).The developed method is simple, convenient and amenable for large scale production of antibody immobilized polystyrene tubes.     

Layer-by-layer immobilization of carbon dots fluorescent nanomaterials on single optical fiber

We report within this paper the development of a fiber-optic based sensor for Hg(II) ions. Fluorescent carbon nanoparticles were synthesized by laser ablation and functionalized with PEG₂₀₀ and N-acetyl-l-cysteine so they can be anionic in nature. This characteristic facilitated their deposition by the layer-by-layer assembly method into thin alternating films along with a cationic polyelectrolyte, poly(ethyleneimine). Such films could be immobilized onto the tip of a glass optical fiber, allowing the construction of an optical fluorescence sensor. When immobilized on the fiber-optic tip, the resultant sensor was capable of selectively detecting sub-micromolar concentrations of Hg(II) with an increased sensitivity compared to carbon dot solutions. The fluorescence of the carbon dots was quenched by up to 44% by Hg(II) ions and interference from other metal ions was minimal.     

Interfacial immobilization of monoclonal antibody and detection of human prostate-specific antigen

Antibody orientation and its antigen binding efficiency at interface are of particular interest in many immunoassays and biosensor applications. In this paper, spectroscopic ellipsometry (SE), neutron reflection (NR), and dual polarization interferometry (DPI) have been used to investigate interfacial assembly of the antibody [mouse monoclonal anti-human prostate-specific antigen (anti-hPSA)] at the silicon oxide/water interface and subsequent antigen binding. It was found that the mass density of antibody adsorbed at the interface increased with solution concentration and adsorption time while the antigen binding efficiency showed a steady decline with increasing antibody amount at the interface over the concentration range studied. The amount of antigen bound to the interfacial immobilized antibody reached a maximum when the surface-adsorbed amount of antibody was around 1.5 mg/m(2). This phenomenon is well interpreted by the interfacial structural packing or crowding. NR revealed that the Y-shaped antibody laid flat on the interface at low surface mass density with a thickness around 40 ?, equivalent to the short axial length of the antibody molecule. The loose packing of the antibody within this range resulted in better antigen binding efficiency, while the subsequent increase of surface-adsorbed amount led to the crowding or overlapping of antibody fragments, hence reducing the antigen binding due to the steric hindrance. In situ studies of antigen binding by both NR and DPI demonstrated that the antigen inserted into the antibody layer rather than forming an additional layer on the top. Stability assaying revealed that the antibody immobilized at the silica surface remained stable and active over the monitoring period of 4 months. These results are useful in forming a general understanding of antibody interfacial behavior and particularly relevant to the control of their activity and stability in biosensor development.     

A novel antibody immobilization and its application in immunoaffinity chromatography

A novel antibody immobilization and its application in immunoaffinity chromatography (IAC) were presented. Using acrylamide (AM) as monomer, ethylene glycoldimethacrylate (EGDMA) as cross-linker and bulk polymerization as synthetic method, we prepared a polymer in which the Cu(II) was embedded. The Cu(II)-embedded polymer was tested for its binding with protein. It was found that Cu(II)-embedded polymer displayed a strong binding with bovine serum albumin (BSA). At 80% of methanol, no BSA was released from Cu(II)-embedded polymer. The Cu(II)-embedded polymer was then used as a novel solid support for antibody immobilization. IAC column was prepared by immobilizing polyclonal antibody (pAb) against clenbuterol (CL) on Cu(II)-embedded polymer and packing the Cu(II)-embedded polymer-pAb into a common solid phase extraction (SPE) cartridge. Under optimal extraction conditions, the IAC column was characterized in terms of maximum binding capacity for target analyte, extraction efficiency and reusability. It was revealed that, for IAC column packed with 0.1 g of solid support immobilized with antibody, the maximum capacity for CL was 616 ng; the extraction recoveries of the column for CL from three spiked food samples were 84.4-95.2% with relative standard deviation (RSD) of 9.3-15.5%; after more than 30 times repeated usage, there was not significant loss of specific recognition. The results demonstrated the feasibility of the prepared IAC column for CL extraction. The proposed antibody immobilization method exhibiting the properties of simplicity, low cost, strong binding for target analyte, no leaching of antibody, etc., would be a very useful tool applied in the field of IAC.     

A new antibody immobilization strategy based on electrodeposition of nanometer-sized hydroxyapatite for label-free capacitive immunosensor

A new antibody immobilization strategy was proposed for the fabrication of a label-free capacitive immunosensor based on electrodeposition of nanometer-sized bioactive hydroxyapatite (HAP). By a procedure of constant current cathodal electrodeposition, a nano-HAP film with bioactivity was formed on a self-assembled β-mercaptoethanol monolayer-modified gold electrode. A suitable amount of chitosan was added into the electrodeposition solution with the aim of obtaining a strong and homogeneous HAP-coating film. After blocking with long-chain alkylthiol and then embedding antibody by coupling with divinylsulphone, the electrode was possessed of a higher initial capacitance value, which was suitable for capacitive transduction. The sensitive layer was characterized by Fourier transform infrared spectrum, scanning electron microscopy and electrochemical method. Human transferrin immunoassay was selected as the testing system. The linear response range of the sensor for transferrin was between 1 and 100 ng/mL with a detection limit of 0.15 ng/mL. After simply rinsing with subacidity solution, the regenerated sensor achieved up to 10 assay cycles without significant loss of sensitivity.     

Influence of antibody immobilization strategy on molecular recognition force microscopy measurements

A systematic evaluation of the effects of antibody immobilization strategy on the binding efficiency and selectivity (e.g., ability to distinguish between specific and nonspecific interactions) of immunosurfaces prepared with F(ab') antibody fragments of rabbit Immunoglobulin G (IgG) is described. F(ab') was attached to gold surfaces either (1) directly via the formation of a gold-thiolate bond or (2) indirectly through a series of a bifunctional linkers containing an alkane chain or ethylene glycol spacer. Immobilization of F(ab') via the sulfhydryl reactive group located opposite the antigen binding site ensured optimum orientation of the antigen binding site. X-ray photoelectron spectroscopy (XPS) and surface plasmon resonance (SPR) were used to confirm surface modification with the bifunctional linkers and antibody immobilization, respectively. Binding efficiency assays performed with SPR indicated that increasing the length of the linker increased the antigen binding efficiency. Atomic force microscopy (AFM) adhesion force measurements indicated that AFM probes functionalized with directly immobilized F(ab') more effectively discriminated between specific and nonspecific surface-bound proteins than probes modified indirectly via linker-immobilized F(ab'). In addition, a greater number of antibody-antigen binding events were observed with directly immobilized F(ab')-functionalized probes.     

pH-controlled construction of chitosan/alginate multilayer film: characterization and application for antibody immobilization

In this work, a chitosan/alginate multilayer film was constructed via layer-by-layer self-assembly and studied by in situ surface plasmon resonance monitoring and contact angle measurements. The results demonstrate that the surface composition of the self-assembled multilayer film can be simply tailored through pH control during the assembly process. The biological property of the assembled film was further characterized via antigen-antibody interactions, showing that the loading capacity of the antibody on the multilayered film and the binding activity of the antigen to the immobilized antibody could be also well-tuned by pH control. This work can provide more scientific insight in the interaction between protein and polymer matrix and render a novel simple approach to build high-performance biointerfaces through pH control for potential applications of highly sensitive immunosensors.