Determination of Molybdenum in Human Urine by Spectrophotometric Method using Thiazolylazo Compounds as Chromogenic Reagents

ABSTRACT

Four azo compounds based on diazotization of 2-aminobenzothiazole have been synthesized and characterized by elemental analysis as well as different spectroscopic techniques. The potentiality of the prepared compounds as new chromogenic reagents for the spectrophotometric determination of Mo⁶⁺ was studied by extensive investigation of optimum conditions favouring the formation of the coloured complexes. Beers law is obeyed in the concentration range 0.2-8.5 μg ml^?1 whereas Ringbom optimum concentration range was 0.8-7.5 μg ml^?1. The detection limit was 0.05 μg ml^?1. The molar absorptivity and Sandell sensitivity of the formed complexes are calculated. The effect of interfering ions on the determination of Mo⁶⁺ was investigated. The relative standard deviations for six replicate determinations of 5.0 μg ml^?1 of Mo⁶⁺ are 1.23, 1.47, 1.05 and 1.38 % using reagents I, II, III and IV, respectively. The proposed method has been applied to investigate the amount of Mo⁶⁺ in human urine samples. The molybdenum levels found between 0.5-2.1 μg/100 ml.     

Simultaneous Determination of Valsartan and Hydrochlorothiazide in Tablets by High-Performance Liquid Chromatography

ABSTRACT

A method for the simultaneous determination of valsartan and hydrochlorothiazide in tablets is described. The procedure, based on the use of reversed-phase high-performance liquid chromatography, is linear in the concentration range 5.0-10.0 μg ml^?1 for valsartan and 0.5-2.0 μg ml^?1 for hydrochlorothiazide, is simple and rapid and allows accurate and precise results. The limit of detection was 1.0 μg ml^?1 for valsartan and 0.05 μg ml^?1 for hydrochlorothiazide.     

Direct detection of acetaminophen in urine by liquid chromatography with electrochemical detection using dual electrodes. Preliminary application to a single-dose pharmacokinetic study

A method for the direct determination of acetaminophen in urine based on liquid chromatography with series dual-electrode detection has been developed. No sample pretreatment steps are required except for filtration. The method gives a linear range from 0.5 to 300 μg ml^?1 and a detection limit of 0.2 μg ml^?1 (10 μl). The analysis time of the assay is less than 7 min. The pharmacokinetics of acetaminophen in urine from a subject who had orally ingested 450 mg (table form) of the drug were studied and various pharmacokinetic parameters were determined.     

Amperometric determination of formaldehyde via the hexacyanoferrate(III) -coupled dehydrogenase reaction

An enzymatic method with amperometric detection was developed for the determination of formaldehyde. Formaldehyde is first oxidized by reaction with NAD⁺ in the presence of formaldehyde dehydrogenase. The resulting NADH is then oxidized by hexacyanoferrate(III) in the presence of diaphorase to produce hexacyanoferrate(II). The anodic current generated by oxidation of the hexacyanoferrate(II) at the surface of a glassy carbon working electrode, held at a potential of 0.40 V vs. an Ag/AgCl reference electrode, is measured. The effects of solution conditions are examined and a linear relationship between rate of current change and formaldehyde concentration is obtained from 0.01 to 0.5 μg ml^?1 with a correlation coefficient of 0.9998. The relative standard deviation for the proposed method is 6.4% at 0.01 μg ml^?1 formaldehyde and 0.88% at 0.5 μg ml^?1.     

Atomic absorption spectrometric studies of the atomization of boron from a carbon rod atomizer

Boron (<20 μg ml^?1) in aqueous solutions gives no absorbance but addition of ascorbic acid, especially with titanium greatly enhances the signal, leading to a detection limit of 0.2 μg ml^?1 boron. The presence of uranium (<10 mg ml^?) only slightly decreases the boron signal.     

Isomeric Transformation Of 4-Aminobiphenyl by U.V. Radiation and its Influence on the Determination by Flow Injection Analysis with Amperometric and Spectrophotometric Detection.

Abstract

Two flow-injection methods for the determination of 4-aminobiphenyl by amperometry (glassy carbon electrode) and spectrophotometry are proposed. A sample volume of 200 or 400 μl containing an analyte concentration of 0.1–1.0 μg ml^?1 or 0.8–24.0 μg ml^?1 for amperometric or spectrophotometric detection, respectively, is injected into a carrier stream containing 0.04 or 0.02 M Britton-Robinson buffer at pH 10.0 or 8.0, respectively.

The throughput thus achieved is 200 (amperometry) and 240 samples/h (spectrophotometry) and the relative standard deviation less than 2.5% and 4.2% respectively.

Both methods were applied to the determination of 4-aminobiphenyl in commercially available, legally permitted food colouring additive.     

Sensitivity enhancement for inductively-coupled plasma atomic emission spectrometry of cadmium by suction-flow on-line ion-exchange preconcentration

A column of iminodiacetate chelating resin is used to preconcentrate cadmium by a factor of 25-fold for a 5-ml sample. The sampling rate was 25 h^?1, and the detection limit 0.05 ng Cd²⁺ ml^?1. The r.s.d. for 0.1 μg Cd²⁺ ml^?1 was 2.2% (n = 10). This technique was applied to the determination of cadmium in certified biological reference materials and waste-water samples.     

Colorimetric Determination of Propofol in Bulk form,Dosage Form and Biological Fluids

ABSTRACT

Propofol is coupled with 2, 6-dichloroquinone-4-chlorimide (DCQ) in a reaction buffered at pH 9.6 to give a colored product having an analytically useful maximum at 635 nm. The factors affecting the color generation were optimized and incorporated in the procedure. The reacted propofol has a molar absorptivity of 3.9 × 10^?4 L mol^?1 cm^?1, and Beer's law is obeyed for concentrations 1-5 μg ml^?1 with detection limit 0.25 μg ml^?1. The method was found applicable to biological fluids (plasma and urine) spiked with propofol at concentration levels 1-5 μg ml^?1 for plasma and 1-5 μg 0.5 ml^?1 urine (less sensitivity is obtained with urine volumes above 0.5 ml) with detection limits 0.28 μg ml^?1 for plasma and 0.4 μg 0.5 ml^?1 urine. The average recovery for the commercial preparation (1% w/v propofol emulsion intravenous injection for infusion) was 99.54% with an RSD of 1.05%. The method was validated by an adopted HPLC method. The results obtained by the HPLC method for the commercial preparation were statistically compared with the proposed method and evaluated at the 95% confidence limits.     

Kinetic-Spectrophotometric Determination of Molybdenum(VI) Based on Its Catalytic Effect on the Thionine-Hydrazine Reaction

Abstract

A kinetic method for the determination of trace amounts of Mo(VI) (0.05-4 μg ml^?1) based on its catalytic effect on the reduction of thionine by hydrazine monochloride in strongly acidic media is reported. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of thionine at 605 nm after a fixed time (5 min.). The detection limit of the method is 23 ng ml^?1 and the relative standard deviation (RSD) for 0.05 μg ml^?1 of Mo(VI) is 1.2% (n=7). The method is almost free from interferences, especially from large amounts of tungsten. The procedure was successfully applied to the determination of trace amounts of molybdenum in steel.     

Fluorimetric determination of mebendazole and flubendazole in pharmaceutical dosage forms after alkaline hydrolysis

The selective and very sensitive fluorimetric determination of mebendazole and flubendazole is based on alkaline hydrolysis and adsorption on Whatman 42 filter paper. Limits of detection are 0.1 μg ml^?1 and 0.5 μg ml^?1, respectively, with linear response sponse up to 10 μg ml^?1 and 50 μg ml^t?1. The fluorescence produced is very stable (λ_em = 460 nm) and the method is applicable to anthelmintic pharmaceutical preparations.     

ABTS‐Multiwalled Carbon Nanotubes Nanocomposite/Bi Film Electrode for Sensitive Determination of Cd and Pb by Differential Pulse Stripping Voltammetry

A 2,2′‐azinobis (3‐ethylbenzothiazoline‐6‐sulfonate) diammonium salt (ABTS)‐multiwalled carbon nanotubes (MWCNTs) nanocomposite/Bi film modified glassy carbon (GC) electrode was constructed for the differential pulse stripping voltammetric determination of trace Pb²⁺ and Cd²⁺. This electrode was more sensitive than ABTS‐free Bi/GC and Bi/MWCNTs/GC electrodes. Linear responses were obtained in the range from 0.5 to 35 μg L^?1 for Cd²⁺ and 0.2 to 50 μg L^?1 Pb(II), with detection limits of 0.2 μg L^?1 for Cd²⁺ and 0.1 μg L^?1 for Pb²⁺, respectively. This sensor was applied to the simultaneous detection of Cd²⁺ and Pb²⁺ in water samples with satisfactory recovery.     

A Fluorosensor with Immobilized Cyclodextrin As A Substrate

Abstract

A flow-through optosensor for phenylalanine and tyrosine is described in this paper. The sensor is developed in conjunction with a flow-injection analysis system and uses immobilized β-cyclodextrin as the sensing agent. The analytical performance characteristics of the proposed sensor for analysis of very low levels of phenylalanine and tyrosine were as follows: the detection limits for phenylalanine and tyrosine were 0.20 μg ml^?1 and 8.9 ng ml^?1, respectively. The observed relative standard deviations were 1.03% for 50 μg ml^?1 of phenylalanine (n = 7) and 3.6% for 0.1 μg ml^?1 of tyrosine (n = 7), respectively.     

Direct determination of biacetyl in fats by sensitized room temperature phosphorescence

A direct method for the determination of biacetyl in butter and margarine by sensitized room temperature phosphorescence (SRTP) is described. After dissolution of the sample in hexane, biacetyl is isolated by distillation, and its native phosphorescence is sensitized by a non-polar linear furocoumarin, 4′5′-dihydro-3-carbethoxypsoralen. The limit of detection is 0.05 ng ml^?1 biacetyl, with a linear response from 1 × 10^?4 to 1 μg ml^?1 (r = 0.999). The RSD is 3.5% at 100 ng ml^?1.     

Cathodic Electrochemical Detection of Nitrophenols at a Bismuth Film Electrode for Use in Flow Analysis

The bismuth film electrode (BiFE) is presented for use in both batch voltammetric and flow injection (FI) amperometric detection of some nitrophenols (2‐nitrophenol, 2‐NP; 4‐nitrophenol, 4‐NP; 2,4‐dinitrophenol, 2,4‐DNP). The bismuth film was deposited ex situ (batch measurements) and in‐line (FI) onto a glassy carbon substrate electrode. Batch analysis of the nitrophenols was carried out in 0.04 M Britton Robinson (BR) buffer pH 4, while for FI measurements, a carrier/electrolyte solution composed of 0.1 M BR buffer pH 4 mixed with methanol (20+80, v/v%) was employed to resemble media used in preconcentration/clean‐up and flow separation sample pretreatment procedures. Under batch conditions, the voltammetric behavior of the nitrophenols was examined for dependence on medium pH in the range of 2 to 10. Employing the square‐wave voltammetry mode, the limits of detection were 0.4 μg L^?1, 1.4 μg L^?1, and 3.3 μg L^?1 for 2‐NP, 4‐NP, and 2,4‐DNP, respectively. Under flow conditions, a simple in‐line electrochemical bismuth film renewal procedure was tested and shown to provide very good inter‐ and intra‐electrode reproducibility of the current signals at low μg L^?1 analyte concentrations. The limits of detection for 2‐NP, 4‐NP and 2,4‐DNP obtained using FI and amperometric detection at ?1.0 V (vs. Ag/AgCl) were 0.3 μg L^?1, 0.6 μg L^?1 and 0.7 μg L^?1, respectively, with linear ranges extending up to 20 μg L^?1. The attractive performance of the BiFE under flow analysis conditions offers great promise with respect to its detection capability and to its use for a prolonged period of time with no need for inconvenient removal of the electrode from the system for mechanical surface treatment.     

Flow-injection spectrophotometric determination of arylamines and sulphonamides by diazotization and coupling in a micellar medium

In a sodium dodecyl sulphate (SDS) micellar solution, the rate of coupling of a diazonium ion with N-(1- naphthyl)ethylenediamine (NED) increases greatly, the protonation of the resulting azo dyes takes place at higher pH values and the dyes are more soluble. These favourable features were applied to the development of a simple flow-injection spectrophotometric procedure for the determination of diazotizable substances of pharmaceutical interest. Limits of detection in the range 0.2–0.5 μg ml^?1 (signal-to-noise ratio=3), with relative standard deviation of 0.7–3% (n=3) for 5 μg ml^?1 standards, were obtained.     

Determination of phosphorus in biological tissues by aluminium block digestion and flow-injection spectrophotometry

Biological tissues are digested with nitric and perchloric acids in a heated aluminium block. Flow-injection spectrophotometry is then used to measure phosphate via the phosphovanadomolybdate complex at 413 nm. The detection limit is 0.3 μg ml^?1 phosphorus; relative standard deviations are 0.7% and 0.4% at 1 μg ml^?1 and 25 μg ml^?1 phosphorus, respectively. Interferences are discussed. The decomposition procedure is evaluated for model compounds and standard reference materials.     

Sensitivity enhancement by palladium addition in the electrothermal atomic absorption spectrometry of mercury

In graphite-furnace atomic absorption spectrometry of mercury, addition of 50 μg ml^?1 palladium improves the peak height for 5 μg Hg ml^?1 50 times. Further addition of 20 μg ml^?1 platinum doubles the enhanced peak height. The effect is due to amalgam formation. The best sensitivity is 0.3 ng (1% absorption) and the detection limit is 0.1 ng. The method allows higher ashing temperatures than for solutions without noble metal addition and can be applied to solutions containing substantial amount of organic matter.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Determination of mixtures of ampicillin and cloxacillin in pharmaceuticals by second-derivative spectrophotometry

Mixtures of ampicillin-Na and cloxacillin-Na are assayed by peak-to-baseline and zero-crossing second-derivative spectrophotometry. The procedure does not require any separation step. Calibration plots are linear (r = 0.9999) up to 30 μg ml^?1 of ampicillin-Na at 216 nm and up to 40 μg ml^?1 ampicillin-Na or cloxacillin-Na at 228 nm or 248.8 nm, respectively, in the presence of one another. Detection limits at the p = 0.05 level of significance, range from 0.15 pg ml^?1 to 0.33 μg ml^?1. The method was successfully applied to commercial injections and capsules containing these penicillins.     

Inductively-coupled plasma atomic emission spectrometric determination of boron based on generation of methyl borate

Boron is converted to methyl borate, distilled and condensed, and selectively volatilized at 50°C into the plasma without interference from methanol, which quenches the plasma. The 3σ detection limit is 40 ng ml^?1 boron, the calibration graph is linear up to 10 μg ml^?1 and the r.s.d. 3.0% for 2.0 μg ml^?1 (n = 10). Boron is determined in plant-tissue and steel standards.