Kinetic spectrophotometric method for gold(III) determination

The kinetic spectrophotometric method for Au(III) determination was developed and validated. It was based on the catalytic effect of gold on the oxidation of methylene blue B (3,7di-(dimethyl amino)-10-dehydro-phenotiazin chloride) by ammonium peroxo-disulfate in citric buffer solution. There was the linearity of the calibration curve in the concentration range from 0.09 to 2.90 μg ml⁻¹ Au(III). The relative standard deviation was 2.50% and correlation coefficient of 0.9999. The limit of detection was determined as signal to noise ratio (3:1) and it was 5.5 ng ml⁻¹. The limit of quantification, based on signal to noise ratio 10:1 was 19.25 ng ml⁻¹. The selectivity was tested on the basis of influence of known amounts of different ions in the reaction mixture, upon the reaction rate. Kinetic and thermodynamic parameters were reported for both catalytic and non-catalytic reactions. The method was verified by Au(III) determination in anti-rheumatic drug “Tauredon” and in human urine samples, using ICP-AES as the comparative method. As the method is accurate, reliable, quick and simple it could be useful for clinical and toxicological practice.     

Extraction and spectrophotometric determination of thallium(III) with thiothenoyltrifluoroacetone

A procedure is described for the extractive photometric determination of thallium(III) with thiothenoyltrifluoroacetone in carbon tetrachloride. Thallium(III) is extracted quantitatively at pH 4-5 and the bright yellow extract obeys Beer's law over the Tl(III) concentration range 2.5-17.5 mug/ml, at 440 nm. Thallium(III) can be determined in the presence of a large number of cations and anions.     

Synergetic extraction and spectrophotometric determination of gold(III)

Summary A method is described for the synergetic extraction and subsequent spectrophotometric determination of gold(III). The gold--furil dioxime-pyridine complex extracted into chloroform has a characteristic yellow colour with an absorption maximum at 330 nm. Beer's law is obeyed in the concentration range [Au(III)]45g/ 10 ml organic phase. A scheme to separate gold from interfering elements by extraction with 4-methyl-2-pentanol in benzene has been proposed.

---

Zusammenfassung Ein Verfahren zur synergetischen Extraktion und nachfolgenden spektrophotometrischen Bestimmung von Gold(III) wurde beschrieben. Die Komplexverbindung des Goldes mit-Furildioxim und Pyridin ist in chloroformischer Lösung gelb gefärbt. Ihr Absorptionsmaximum liegt bei 330 nm. Bis 45g Au(III)/10 ml organischer Phase wird das Beersche Gesetz befolgt. Die Trennung des Goldes von störenden Elementen durch Extraktion mit 4-Methyl-2-pentanol in Benzol wurde vorgeschlagen.

     

Titration of methylene blue with chloromolybdate(III)

The reaction of Methylene Blue with aquomolybdenum(III) chloride and chloromolyb-date(III) in hydrochloric acid media has been investigated. Chloromolybdate(III) can be satisfactorily used as a reductometric titrant for Methylene Blue in 6-8M hydrochloric acid medium. The end-point can be detected either potentiometrically or visually. Aquomolybdenum(III) chloride is not useful as a titrant for this estimation.     

Extraction and spectrophotometric determination of cobalt(II) with isonitroso-5-methyl-2-hexanone

A simple and selective method is proposed for the extraction of cobalt(II) for its spectrophotometric determination using (HIMH) as an extractant. Cobalt(II) forms a yellow coloured complex with HIMH which can be extracted into chloroform. The calibration curve is rectilinear in the concentration range 0.1–5.0 μg ml⁻¹ of cobalt(II). The extracted species shows an absorption maximum at 400 nm with molar absorptivity of 1.135×10⁴ l mol⁻¹ cm⁻¹. The method has been applied for the determination of cobalt in synthetic mixtures, pharmaceutical, biological and high speed steel samples.     

Flotation—spectrophotometric determination of osmium with thiocyanate and methylene blue

A sensitive flotation—spectrophotometric method, based on the ion associate formed by the anionic thiocyanate complex of osmium with the basic dye methylene blue (MB) is described. The ion associate precipitates when the aqueous solution is shaken with toluene, and the separated and washed compound is dissolved in acetone. The molar absorptivity is 2.2 × 10⁵ l mol^-1 cm^-1 at 655 nm. Beer's law is obeyed. The molar ratio of Os:SCN:MB in the separated and washed ion associate is 1:6:3. Ruthenium reacts similarly. The method is applied to the determination of traces of osmium in crucible platinum after separation of osmium by distillation as tetroxide.     

Synthesis of 4-(3-hydroxyalkyl)pyrimidines by ring transformation reactions of 2-alkylidenetetrahydrofurans with amidines

Domino reactions of amidines with 2-alkylidenetetrahydrofurans, prepared by cyclization of 1,3-dicarbonyl dianions or 1,3-bis-silyl enol ethers with various dielectrophiles, provided an efficient access to 4-(3-hydroxyalkyl)pyrimidines.     

Selective extraction of melamine using 11-mercaptoundecanoic acid-capped gold nanoparticles followed by capillary electrophoresis

This study describes the use of 11-mercaptoundecanoic acid-capped gold nanoparticles (MUA-AuNPs) for selective extraction of melamine prior to analysis by capillary electrophoresis with UV detection. The highest degree of melamine-induced aggregation of MUA-AuNPs was found to occur at pH 5.0, indicating that the NP aggregation is mainly because of hydrogen bonding between the carboxylate groups of MUA and the amine groups of melamine. Moreover, the degree of melamine-induced NP aggregation gradually increased when the chain length of the mercaptoalkanoic acid was increased from two to 12 carbon atoms. At pH 5.0, the extraction efficiency of melamine was highly dependent on the concentration of MUA-AuNPs, the concentration of dithiothreitol (DTT), the extraction time between MUA-AuNPs and melamine, and the incubation time between melamine-adsorbed AuNPs and DTT. The separation of the extracted melamine and DTT (releasing agent) was accomplished using a solution of 10 mM phosphate (pH 6.0) containing 1.6% (v/v) poly(diallyldimethylammonium chloride). Under the optimum extraction and separation conditions, the limit of detection at a signal-to-noise ratio of 3 was estimated to be 77 pM for melamine, with linear range of 1-1000 nM. The proposed method was successfully applied to the determination of melamine in tap water and in milk.     

Extraction of palladium from nitric acid medium and its spectrophotometric determination using arsenazo III

Summary Di-octyl sulphoxide in xylene was successfully employed for extracting palladium from 0.5 to 1.5 mol/l nitric acid medium. The extracted species was found to be Pd(NO₃)₂·2DOSO. The palladium was back extracted into a mixture of 2 mol/l sodium carbonate and 0.05 mol/l ammonia. The recovery was found to be quantitative. A spectrophotometric method using Arsenazo III was developed in nitric acid medium for the determination of palladium. The colour development was found to be maximum in the acid range of 2.5 to 5 mol/l. Beer's law was found to be obeyed in 1 to 100 g range of palladium. The molar extinction coefficient was found to be 2.26×10⁴ l/mol/cm. The RSD obtained at 16 g of palladium was 5%.     

Extraction of Ce(III), Gd(III) and Yb(III) from Citrate Medium by High Molecular Weight Amines

Abstract

High molecular weight amines have been used for the extraction of citrate complexes of Ce(III), Gd(III) and Yb(III). The effect of different variables on extraction has been studied. The citrate species extracted in the organic phase have been proposed as [(RNH₃ ⁺)₃] [M(Cit)₂]^3-.     

Determination of gold in ore by flame atomic absorption spectrometry with flow-injection on-line sorbent extraction preconcentration

Gold in ores was determined by flame atomic absorption spectrometry following on-line preconcentration by sorbent extraction in a flow-injection system. The medium polarity adsorption resin Amberlite XAD-8 packed in a 220-μl micro-column was used to collect gold(III) from hydrochloric acid sample solutions for 40 s at 7.6 ml/min. Ethanol was used to elute the adsorbed analytes into the nebulizer. Optimization studies were made on sample loading rate, elution rate and sample acidity. Some possible interferences on the determination are discussed. A 35-fold enrichment was achieved at a sampling frequency of 60 h^?1 and with an RSD of 1.4%. The detection limit (3σ) and 2 μg l^?1. Results for gold in ore samples showed good agreement with those obtained using activated carbon adsorption preconcentration. The recoveries were 97–108%.     

Photocured thiol-ene based optical fluorescence sensor for determination of gold(III)

This study describes the preparation and the characterization of a new thiol-ene based polymeric fluorescence sensor by photo initiated polymerization of trimethylolpropane tris(3-mercaptopropionate), 2-hydroxyethylacrylate, and 2,4,6-triallyloxy-1,3,5-triazine which are used as monomers and also a photo initiator (2,2-dimethoxy-2-phenylacetophenone) for its usage as optical sensor for gold ions. The thiol-ene based polymeric membrane sensor was characterized by using attenuated total reflectance-fourier transform infrared spectroscopy (ATR-FTIR) and scanning electron microscopy (SEM). The response characteristics of the sensors including dynamic range, pH effect, response time, and the effect of foreign ions were investigated. Fluorescence spectra showed that the excitation/emission maxima of the membrane were at 379/425 nm, respectively     

Extraction of lead(II) with cyanex 302 and its spectrophotometric determination with PAR

A method is developed for the extraction of lead(II) from an aqueous solution of pH 2.1-8.3 with cyanex 302 [bis(2,4,4-trimethylpentyl monothiophosphinic acid)] in toluene as an extractant. Lead(II) was stripped with 0.1 mol dm(-3) nitric acid and determined spectrophotometrically with PAR. The method is most sensitive and permits the separation of lead(II) from binary mixtures containing commonly associated metal ions. The method is applicable for the separation and determination of lead in alloys and environmental samples.