生物功能电极 III. 葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合, 将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响, 并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现, 由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性, 酶反应表观上遵循Michealis-Menten动力学。     

生物功能电极 Ⅲ.葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合,将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响,并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现,由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性,酶反应表观上遵循Michealis-Menten动力学。     

Detection of phenolic compounds in flow systems based on tyrosinase-modified reticulated vitreous carbon electrodes

The fabrication and performance of a reticulated vitreous carbon (RVC)-based tyrosinase flow-through electrode, in which the enzyme was covalently immobilized, is reported. The bioelectrode was tested as an amperometric detector for phenolic compounds. Variables affecting the construction of the enzyme flow-through electrode such as the RVC chemical pretreatment procedure, the enzyme immobilization method in the RVC matrix, the enzyme loading and the pH value of the buffer solution used, were optimized by flow-injection with amperometric detection. A good immobilization of the enzyme in the RVC matrix, in spite of the hydrodynamic conditions, was found. The same tyrosinase-RVC electrode could be used with no significant loss of the amperometric response for around 20 days, and reproducible responses could be achieved with different electrodes constructed in the same manner. Moreover, the operational stability of the bioelectrode was tested under continuous monitorization conditions. Calibration plots by flow injection with amperometric detection at -0.20 V were obtained for phenol, 2,4-dimethylphenol; 3-chlorophenol; 4-chlorophenol; 4-chloro-3-methylphenol and 2-aminophenol, with detection limits ranging from 2 mug l(-1) (4-chloro-3-methylphenol) to 2 mg l(-1).     

Determination of underivatized amino acids by high-performance liquid chromatography and electrochemical detection at an amino acid oxidase immobilized CuPtCI6 modified electrode

An amperometric sensor for amino acids based on the immobilization of amino acid oxidase on the surface of a CuPtCl(6)/GC is described. The amperometric current is due to the oxidation of H2O2 liberated during the enzyme reaction on the surface of the enzyme electrode. The electrode response characteristics as well as kinetic parameters have been evaluated. The enzyme electrode was characterized as an electrochemical biosensor, which was used as detector in high performance liquid chromatography (HPLC) for the determination of a mixture of amino acids with satisfactory results.     

Determination of underivatized amino acids by high-performance liquid chromatography and electrochemical detection at an amino acid oxidase immobilized CuPtCl6 modified electrode

An amperometric sensor for amino acids based on the immobilization of amino acid oxidase on the surface of a CuPtCl₆/GC is described. The amperometric current is due to the oxidation of H₂O₂ liberated during the enzyme reaction on the surface of the enzyme electrode. The electrode response characteristics as well as kinetic parameters have been evaluated. The enzyme electrode was characterized as an electrochemical biosensor, which was used as detector in high performance liquid chromatography (HPLC) for the determination of a mixture of amino acids with satisfactory results. Received: 31 Jaunary 2000 / Revised: 31 March 2000 / Accepted: 3 April 2000     

Immobilization of histidine-tagged proteins on electrodes

The development of new enzyme immobilization techniques that do not affect catalytic activity or conformation of a protein is an important research task in biotechnology including biosensor applications and heterogeneous reaction systems. One of the most promising approaches for controlled protein immobilization is based on the immobilized metal ion affinity chromatography (IMAC) principle originally developed for protein purification. Here we describe the current status and future perspectives of immobilization of His-tagged proteins on electrode surfaces. Recombinant proteins comprising histidine-tags or histidine rich native proteins have a strong affinity to transition metal ions. For metal ion immobilization at the electrode surface different matrices can be used such as self-assembled monolayers or conductive polymers. This specific technique allows a reversible immobilization of histidine-tagged proteins at electrodes in a defined orientation which is an important prerequisite for efficient electron transfer between the electrode and the biomolecule. Any application requiring immobilized biocatalysts on electrodes can make use of this immobilization approach, making future biosensors and biocatalytic technologies more sensitive, simpler, reusable and less expensive while only requiring mild enzyme modifications.     

Immobilization of glucose oxidase on carbon paper electrodes modified with conducting polymer and its application to a glucose fuel cell

A carbon paper electrode was modified with the conducting copolymer of 3-methylthiopene and thiophene-3-acetic acid prepared electrochemically on the electrode, and an enzyme electrode was fabricated by covalent immobilization of glucose oxidase on the modified electrode. The modification with the conducting copolymer increased the surface area of the electrode and the amount of the immobilized enzyme. As a result, the enzyme electrode showed a high catalytic activity. Moreover, it was found that the increased surface area led to a high rate of electron transfer reaction between the electrode and p-benzoquinone employed as an electron mediator. The enzyme electrode fabricated with the modified carbon paper gave a larger glucose oxidation current than that fabricated with the bare one. In addition, the glucose oxidation current was found to increase with increasing content of the conducting copolymer in the modified carbon paper. Corresponding to the large glucose oxidation current, high performance was confirmed for the glucose fuel cell constructed with the enzyme electrode based on the modified carbon paper.     

亲水金和憎水二氧化硅纳米颗粒对葡萄糖生物传感器响应灵敏度的增强作用

用亲水金、憎水二氧化硅纳米颗粒固定葡萄糖氧化酶(GOD),采用聚乙烯醇缩丁醛(PVB)为辅助固酶膜基质来制备葡萄糖生物传感器,并考察了亲水金、憎水二氧化硅纳米颗粒对酶电极电流响应的影响.实验表明,引入纳米粒子可显著增强电极响应灵敏度.并对两种不同性质纳米颗粒所起作用的可能机理进行讨论,从理论和实验上证明了纳米颗粒对固定酶的作用.为制备有实用价值的葡萄糖生物传感器提供了可供参考的实验和理论依据.     

过氧化氢在磺酸二茂铁掺杂的聚苯胺上的电催化氧化

在含有磺酸二茂铁溶液中合成的聚苯胺（PAnFc）和不含磺酸二茂铁溶液中合成的聚苯胺（PAn）,在pH 5.0的缓冲溶液中均能催化过氧化氢的氧化,但PAnFc的催化活性高于PAn.催化效应的证据是过氧化氢在裸铂电极上的氧化电位为0.59 V(vs SCE),而在PAnFc电极仅是0.48 V,以及过氧化氢在PAnFc电极上的阳极峰电流是裸铂电极上的5.3倍.根据这种催化特性,用PAn和PAnFc固定葡萄糖氧化酶形成酶电极.实验结果表明,PAnFc酶电极的响应电流比PAn酶电极高得多,而且响应快.这是由于PAnFc在pH 5.0缓冲液中的电化学活性高于PAn,以及掺杂在聚苯胺中的磺酸二茂铁起着重要的电荷传递作用.     

Highly sensitive sensors based on the immobilization of tyrosinase in chitosan

A novel tyrosinase biosensor has been developed for a subpicomolar detection of phenols, which is based on the immobilization of tyrosinase in a positively charged chitosan film on a glassy carbon electrode. It was found that chitosan cross-linked with (3-aminooryloxypropyl) dimethoxymethylsilane is beneficial for the immobilization of tyrosinase. The large microscopic surface area and porous morphology of chitosan matrix lead to high enzyme loading, and the enzyme entrapped in this matrix can retain its bioactivity and the positively charged surface of chitosan can also display a good anti-interference ability to the substances with positive charge. Hence, the resulting sensor offers a high-sensitivity (150 nA.nM(-1)) for the monitoring of phenols, and the detection limit is as low as 5.0 x 10(-11) M. Its response time is less than 2 s reaching 95% of the steady-state value. It may retain 75% of the activity for at least 70 days.     

An Amperometric Biosensor Based on Laccase Immobilized in Polymer Matrices for Determining Phenolic Compounds

An amperometric enzyme electrode based on laccase for determining phenolic compounds is proposed. The following three types of polymer materials were used for enzyme immobilization on the surface of a glassy-carbon electrode: positively charged cetyl ethyl poly(ethyleneimine) (CEPEI) and negatively charged commercial Nafion and Eastman AQ 29D polymers. The advantages and disadvantages of each of the above polymers for enzyme immobilization are discussed. The detection limits of the model phenolic compounds hydroquinone and pyrocatechol in a buffer solution on laccase immobilization in a Nafion membrane were 3.5 × 10⁻⁸ and 5.0 × 10⁻⁸ M, respectively, at a signal-to-noise ratio of 3. Electrodes with laccase immobilized in Nafion and Eastman AQ 29D membranes exhibited the shortest response time. The operating stability and the stability in storage can be significantly improved by the additional incorporation of gelatin in the polymer matrices. Gelatin prevents enzyme inactivation as a result of enzyme modification by the free-radical oxidation products of phenolic compounds.__________Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 624–628.Original Russian Text Copyright © 2005 by Yaropolov, Shleev, Morozova, Zaitseva, Marko-Varga, Emneus, Gorton.Presented at the VI All-Russia Conference (with international participation) on Electrochemical Methods of Analysis (EMA-2004, Ufa, May 23–27, 2004).     

Enzyme immobilization procedures on screen-printed electrodes used for the detection of anticholinesterase pesticides: Comparative study

A comparison between several acetylcholinesterase (AChE) immobilization procedures on the 7,7,8,8-tetracyanoquinodimethane (TCNQ)-modified graphite working electrodes is presented. The immobilization methods employed crosslinking with glutaraldehyde in presence of BSA protein and photopolymerization with poly(vinyl alcohol) bearing styrylpyridinium groups (PVA-SbQ). The main variations were related to the enzyme charge in each electrode and the enzyme conditioning and storage conditions after immobilization. Initially, the enzyme-substrate reaction was carried out and the following parameters were chrono-amperometrically and -coulometrically monitored: current intensities, time to stabilize the current response, and the mass transfer represented by the Coulomb charge. The screen-printed biosensors that presented best characteristics were then used to perform the inhibition assays and to verify the sensitivity against the following NMC insecticides: aldicarb, carbaryl, carbofuran, and methomyl.In general, diffusion of electrons into the sensitive layer, mass transfer, and time to stabilize the current were adequate in all cases. The Cottrell law was followed before the 1 min of enzyme-substrate reaction. Adequate reproducibility within electrochemical measurements was also observed, with relative standard deviations varying from 6.5 to 18.6%.AChE immobilization with glutaraldehyde allow to obtain robust and reproducible biosensors, but they need a much higher enzyme content (80 mUA per electrode) to achieve current values comparable to that constructed by immobilizing the AChE through photopolymerization with PVA-SbQ (0.7 to 1 mUA per electrode). The limits of detection were determined with a minimum 10% inhibition, and varied from 10⁻⁹ to 8×10⁻⁹ M (0.2 to 1.5 ppb) by employing the enzyme immobilization through photopolymerization with PVA-SbQ. In practice, this kind of immobilization procedure is much simpler and produces good results: fast response, adequate reproducibility, large pesticides working ranges, and excellent sensitivities to N-methylcarbamates (NMCs) which in general do not present enzyme inhibition power as elevated as for the organophosphate pesticides.     

Parameters important in fabricating enzyme electrodes using self-assembled monolayers of alkanethiols.

The fabrication of enzyme electrodes using self-assembled monolayers (SAMs) has attracted considerable interest because of the spatial control over the enzyme immobilization. A model system of glucose oxidase covalently bound to a gold electrode modified with a SAM of 3-mercaptopropionic acid was investigated with regard to the effect of fabrication variables such as the surface topography of the underlying gold electrode, the conditions during covalent attachment of the enzyme and the buffer used. The resultant monolayer enzyme electrodes have excellent sensitivity and dynamic range which can easily be adjusted by controlling the amount of enzyme immobilized. The major drawback of such electrodes is the response which is limited by the kinetics of the enzyme rather than mass transport of substrates. Approaches to bringing such enzyme electrodes into the mass transport limiting regime by exploiting direct electron transfer between the enzyme and the electrode are outlined.     

Ferrocene branched chitosan for the construction of a reagentless amperometric hydrogen peroxide biosensor

Chitosan was chemically branched with ferrocene moieties and further used as a support for the immobilization of horseradish peroxidase on a glassy carbon electrode. The reagentless biosensor device showed a linear amperometric response toward hydrogen peroxide concentrations between 35 x 10(-6) M and 2.0 x 10(-3) M. The biosensor reached 95% of the steady-state current in about 20 s and its sensitivity was 28.4 x 10(-3) microA x M(-1). The enzyme electrode retained 94% of its initial activity after 2 weeks of storage at 4 degrees C in 50 x 10(-3) M sodium phosphate buffer at pH 7.0.     

Immobilization of DNA onto poly(dimethylsiloxane) surfaces and application to a microelectrochemical enzyme-amplified DNA hybridization assay

This paper describes immobilization of DNA onto the interior walls of poly(dimethylsiloxane) (PDMS) microsystems and its application to an enzyme-amplified electrochemical DNA assay. DNA immobilization was carried out by silanization of the PDMS surface with 3-mercaptopropyltrimethoxysilane to yield a thiol-terminated surface. 5'-acrylamide-modified DNA reacts with the pendant thiol groups to yield DNA-modified PDMS. Surface-immobilized DNA oligos serve as capture probes for target DNA. Biotin-labeled target DNA hybridizes to the PDMS-immobilized capture DNA, and subsequent introduction of alkaline phosphatase (AP) conjugated to streptavidin results in attachment of the enzyme to hybridized DNA. Electrochemical detection of DNA hybridization benefits from enzyme amplification. Specifically, AP converts electroinactive p-aminophenyl phosphate to electroactive p-aminophenol, which is detected using an indium tin oxide interdigitated array (IDA) electrode. The IDA electrode eliminates the need for a reference electrode and provides a steady-state current that is related to the concentration of hybridized DNA. At present, the limit of detection of the DNA target is 1 nM in a volume of 20 nL, which corresponds to 20 attomoles of DNA.     

Bioelectrocatalytic Oxygen Reduction by Laccase Immobilized on Various Carbon Carriers

Laccase is an enzyme that is used for fabricating cathodes of biofuel cells. Many studies have been aimed at searching the ways for enhancing specific electrochemical characteristics of cathode with the laccase- based catalyst. The electroreduction of oxygen on the electrode with immobilized laccase proceeds under the conditions of direct electron transfer between the electrode and active enzyme center. In this work, the effect of oxygen partial pressure on the electrocatalytic activity of laccase is studied. It is shown that, at the concentrations of oxygen dissolved in the electrolyte higher than 0.28 mM, the process is controlled by the kinetics of the formation of laccase–oxygen complex, whereas at lower concentrations and a polarization higher than 0.3 V, the process is limited by the oxygen diffusion. A wide range of carbon materials are studied as the carriers for laccase immobilization: carbon black and nanotubes with various BET specific surface areas. The conditions, which provide the highest surface coverage of carbon material with enzyme in the course of spontaneous adsorptive immobilization and the highest specific characteristics when using a “floating” electrode simulating a gas-diffusion electrode, are determined: 0.2 M phosphate-acetate buffer solution; oxygen atmosphere; the carrier material (nanotubes with a BET surface area of 210 m²/g and a mesopore volume of 3.8 cm³/g); and the composition of active mass on the electrode (50 wt % of carbon material + 50 wt % of hydrophobized carbon black).     

电极处理对葡萄糖传感器稳定性的影响

针对目前在共价键法固定葡萄糖氧化酶传感器过程中,存在影响传感器稳定性的封装,氧化和后处理3个问题,通过选择新的封装材料,进行多层复合封装,解决了因封装失效影响传感器稳定性的问题。研究了铂电极的氧化方法和氧化程度对传感器稳定性的影响,优化了铂电极的氧化工艺;采用了新的电极通电后处理方法,制得了性能良好的传感器,使电极的稳定性显著提高,经连续测试15天,传感器的相对活性为91％,存放3个月后,传感器的相对活性达到90％。     

Amperometric probe for 3-hydroxybutyrate with immobilized 3-hydroxybutyrate dehydrogenase

The enzyme 3-hydroxybutyrate dehydrogenase is immobilized on a graphite electrode suitable for determination of NADH. Of the several procedures tested for the immobilization, direct adsorption on the electrode surface was most satisfactory, with useful lifetimes of up to 3 days. The best calibration graphs for the NADH, and for 3-hydroxybutyrate were obtained at pH 7.5 (phosphate buffer). 3-Hydroxybutyrate was determined in the range 5–100 μmol l^?1 at pH 7.5 with good precision. Interferences are discussed.     

Catalase‐Modified Carbon Electrodes: Persuading Oxygen To Accept Four Electrons Rather Than Two

We successfully exploited the natural highly efficient activity of an enzyme (catalase) together with carbon electrodes to produce a hybrid electrode for oxygen reduction, very appropriate for energy transformation. Carbon electrodes, in principle, are cheap but poor oxygen reduction materials, because only two‐electron reduction of oxygen occurs at low potentials, whereas four‐electron reduction is key for energy‐transformation technology. With the immobilization of catalase on the surface, the hydrogen peroxide produced electrochemically is decomposed back to oxygen by the enzyme; the enzyme natural activity on the surface regenerates oxygen, which is further reduced by the carbon electrode with no direct electron transfer between the enzyme and the electrode. Near full four‐electron reduction of oxygen is realised on a carbon electrode, which is modified with ease by a commercially available enzyme. The value of such enzyme‐modified electrode for energy‐transformation devices is evident.     

超细Ag颗粒对葡萄糖氧化酶生物传感器响应灵敏度的增强效应

生物传感器在临床医学、环境和食品工业等方面都有重要的用途［１］,且由于其具有体积小、精度高、灵敏度好和便于现场测定等优点,已成为当前研究的热点课题之一．其中研究得较多的是氧化酶电流型生物传感器,特别是介体型,由于其响应快,灵敏而倍受重视．现已报道的可...