Separation and determination of metals as complexes of 1-nitroso-2-naphthol-6-suiphonic and 2-nitroso-1-naphthol-6-sulphonic acids. II. Liquid chromatography on c18 bonded and copolymer stationary phases

An ion-pair Chromatographic system for the separation of copper(II), palladium(II), iron(III) and cobalt(III) as ion-associates of their l-nitroso-2-naphthol-6-sulphonate and 2-nitroso-l-naphthol-6-sulphonate anionic complexes with organic ammonium compounds and inorganic cations has been studied. Isocratic and gradient elution methods were used, and the effects of column material, organic and aqueous modifiers, and pH of the eluent on the retention were examined. The elution time for the metal complex anions depends on the eluent, the proportion of organic solvent in the mobile phase, the pH of the eluent and the extraction coefficient of the compounds. The compounds were identified photometrically with a diode-array detector at wavelengths of 229, 254, 260, 298, 320 and 400 nm. The detection limits for the metals are at the ng/ml level.     

Note on the use of reciprocity of chiral recognition in designing liquid chromatographic chiral stationary phases

The effect of methanol, acetone and acetonitrile on the sensitivity, selectivity and the detection limits (LODs) of the determination of chromium species by ion chromatography was investigated. A collinear dual-beam thermal lens spectrometer was used for the direct detection of chromium complexes [pre-column derivatized Cr(III)–pyridine-2,6-dicarboxylic acid, and post-column derivatized Cr(VI)–1,5-diphenylcarbazide] following the ion chromatographic separation on a Dionex HPIC-CS5A solvent compatible column. Different amounts of organic solvents were added directly to the eluent (up to 30%) and to the post-column reagent (up to 60%) to improve the thermooptical properties of the solvents. Consequently, the sensitivity of the technique was increased by a factor of 2–3 and LODs of 0.1 and 10 μg dm⁻³ were achieved for Cr(VI) and Cr(III), respectively, when the eluent reaching the detector contained 30% of acetonitrile. The addition of organic solvents also resulted in significant changes in retention times, which improved the Cr(III)/Cr(VI) separation.     

Development of a novel multi-element detection system for trace metal determination based on chemiluminescence after separation by ion chromatography

A highly sensitive, non-selective trace metal detector based on chemiluminescence has been developed. The metals, separated by simple ion-exchange chromatography, bring about the displacement of cobalt from a Co-EDTA post-column reagent. The liberated cobalt is then detected by the luminol-peroxide chemiluminescence reaction using a modified spectrofluorimeter as the detector. The metals determined are Mg, Ca, Sr, Ba, Fe(II), Fe(III), Co, Ni, Cu, Zn, the lanthanides, Th, Al, Ga, In, Pb and Bi. The detection limits (three times the baseline noise) range between 2 and 100 μg l^?1, depending on the analyte, for a 200-μl injection. To demonstrate the quantitative performance of the detector, the zinc and aluminium contents of a fresh water certified reference material was determined and gave good agreement with the certificate values.     

Photocatalytic oxidation in aqueous titanium dioxide suspensions: the influence of dissolved transition metals

The influence of type, species distribution, standard reduction potential, and concentration of several transition metals on the rate of photocatalytic oxidation of toluene was investigated. A significant increase in reaction rate was observed in the presence of 10⁻⁵ M Cu(II), Fe(III), and Mn(II) at pH 3, with decreased rates at higher concentrations and pH values. There was no clear correlation between reaction rate and aqueous metal species distribution, nor did the oxidation states of Cu or Fe alter their effects on the reaction rate. Neither Ni(II) nor Zn(II) had a significant influence on the rate of organic oxidation. Negligible adsorption of metals onto TiO₂ was measured at the metal concentrations and pH values for which the highest reaction rates were observed, indicating that dissolved metals increase the reaction rate via a homogeneous pathway rather than a TiO₂ surface reaction. A mechanism involving formation of a reactive complex between the metal, the organic or its oxidation intermediate, and an oxygen-containing species is proposed to explain the experimental data. The rate of the photocatalytic reaction is described by a Langmuir—Hinshelwood rate form, modified to account for homogeneous catalytic pathways and decreased UV transmittance in the presence of dissolved metals.     

The effect of temperature on single-column ion-chromatography of metal ions

Temperature is shown to be a valuable parameter for optimizing single-column ion-chromatographic separations of metal ions. With a perchloric acid eluent, retention times of bivalent metal ions decrease with an increase in system temperature, but with doubly protonated amines as eluents the retention times increase with an increase in temperature. Consequently, increasing the system temperature improves separations of bivalent metal ions when p-phenylenediamine dilhydrochloride is used as the eluent. Both conductivity detection and post-column reaction followed by spectrophotometric detection are suitable detection methods at above-ambient temperatures.     

Determination of trace alkaline earth metals in brines using chelation ion chromatography with an iminodiacetic acid bonded silica column

The chromatographic behaviour of alkaline earth metals on iminodiacetic acid bonded silica was studied. It was found that the ionic strength of the eluent greatly affected both retention time and selectivity by controlling the extent to which either simple ion exchange or surface complexation was responsible for retention. With a 0.1 M KNO3 eluent, the retention order was Mg(II), Sr(II), Ca(II) and Ba(II), indicating a strong contribution to retention from ion exchange. However, when using a 1.5 M KNO3 eluent, Ba(II) was found to elute first, indicating complexation to be more dominant under these conditions (pH 4.2). The effect of the ionic strength of the sample was also studied and it was found that by matching the eluent cation with that of the sample matrix, efficient separations of alkaline earth metals in 1.0 M NaCl and KCl brines could be obtained without matrix system peaks. Using post-column reaction with o-cresolphthalein complexone, trace levels of Ca(II) and Mg(II) were determined in medicinal NaCl saline solution and laboratory-grade KCl.     

Determination of metal ions by on-line complexation and ion-pair chromatography

An ion-pair chromatographic method utilizing on-line complexation and ion-pair formation in a post-column reactor was developed for the determination of copper, palladium, cobalt and iron in mixtures. The system features a reversed-phase column and a second eluent line feeding the ligand reagent, connected after the column via a T-piece, to a mixer and through that to a knitted tubing reactor. The ion-pair former was added to the eluent before the column and the ligand after it. The separation was studied using a binary eluent system containing cetyltrimethylammonium bromide (CTMABr) or tetradecyltrimethylammonium bromide (TDTMABr) in water-methanol (99:1, v/v) as ion-pair former and methanol. In addition, water-methanol (99:1, v/v) containing 1-nitroso-2-naphthol-6-sulphonate (126NNS) as ligand was added to the eluent, through the T-piece, after the column. Mixing of the two eluents took place in the mixer. Methanol was used both isocratically and in gradient addition. Selective UV-VIS detection of the metal-126NNS ion pairs was at wavelengths 230, 260, 310 and 400 nm and their identification was effected in wavelength range 190–600 nm. The metal complex formation in the aqueous methanol eluent evidently governed the retention of the ion pairs, while the selectivity of the method was provided by the different rates of reaction of the metal, the ligand and the ion-pair former in the mixer-reactor system. The detector response for copper, palladium, cobalt and iron was linear up to concentrations of 10 μM. In spiked water-methanol samples the detection limits for these metals ranged from 1·10⁻³ to 1 mg/l. When the on-line complexation and ion-pair formation method was tested with nickel, mercury and zinc, the results proved that these ion pairs were unstable. Because of the insufficient reproducibility of the absorption intensities of these metal ion pairs, their qualitative study could be performed only in the pH range 7–8. The method was successfully applied to real samples after removal of the organic material.     

Simultaneous determination of copper(II) and cobalt(II) by ion chromatography coupled with chemiluminescent detection.

In the absence of any special luminescent reagents, a weakly chemiluminescent emission was observed during the decomposition of hydrogen peroxide, catalyzed by transition-metal ions, such as Cu(II) and Co(II), in basic aqueous solution. The chemiluminescent intensity was significantly enhanced by the addition of ethyldimethylcetylammonium bromide and uranine. The signal-to-noise ratio (S/N) was proportional to the concentrations of Cu(II) and Co(II). Based on these phenomena, a flow-injection chemiluminescent method for the simultaneous separation and determination of Cu(II) and Co(II) was developed. The detection limits of the present chemiluminescent method for Cu(II) and Co(II) were 7.5 and 0.01 ng/ml, respectively. After ion chromatographic separation of Cu(II) and Co(II) by an IonPac CS5A column with oxalic acid and lithium hydroxide monohydrate as the eluent, the present chemiluminescent system was used as a post-column detector for these two transition metal ions in natural water samples.     

Determination of beryllium in a stream sediment by high-performance chelation ion chromatography

High-performance chelation ion chromatography (HPCIC), involving a chelating silica substrate bonded with aminomethylphosphonic acid, has been developed as a novel technique for the quantitative determination of beryllium in complex matrices. An isocratic separation method, using an eluent containing 1 M KNO3, 0.5 M HNO3 and 0.08 M ascorbic acid, allowed the Be2+ to elute away from the sample matrix peak in under 6 min in a sample containing in excess of 800 mg l(-1) matrix metals. A detection limit of 35 microg l(-1) Be(II) was found using a post-column reaction involving Chrome Azurol S (CAS), 1 M hexamine and 10 mM EDTA buffered at pH 6. The standard addition curve gave excellent linearity (R2>0.999). The procedure was applied to the determination of trace beryllium in a certified sediment sample. The results obtained compared well with the certified value for beryllium.     

Separation and analysis of aluminium(III) by cation exchange ion chromatography

A method for the determination of aluminium(III) ions based on separation by cation exchange column chromatography and detection by conductivity detector has been developed. It is fast and reliable, and can be used for the separation and analysis of aluminium(III) ions from other metal ions like Mg(II), Mn(II), Zn(II), Co(II), Ca(II), Sr(II), rare earth elements like Lu(III), Tm(III), and Gd(III), which are eluted at different times and so do not interfere. Effect of p-phenylene diamine concentration present in the eluent, presence of other metal ions and effect of various anions present in the injection sample on the separation and analysis of aluminium(III) ions have also been studied.     

Simultaneous ion-chromatography of alkali, alkaline earth and heavy metal ions with conductivity and indirect UV detection: Comparison of eluents containing organic complexing acids and copper sulfate

Summary The simultaneous ion-chromatography of mono-and divalent metal ions on the weak cation-exchange column Nucleosil-PBDMA (polymer coated silica with polybutandiene-maleic acid) with conductivity and indirect UV-detection is presented. The influences of eluents containing organic complexing acids (-hydroxy-isobutyric, tartaric, citric, oxalic, pyridine-2,6-dicarbonic acid and EDTA etc.) as well as UV-absorbing, displacing counterions [Cu(II), Ce(III) etc.] on the retention times of metal ions was investigated in detail. With the combination of citric acid-PDCA as eluent all alkali and alkaline earth ions could be completely separated within 12 min. Alkali, alkaline earth and heavy metal ions [Cu/Zn/Co/Fe(II)] were separated by the combination of tartaric and oxalic acid as eluent in a single run. Trace amounts of Na, K and Ca were successfully separated from the Mg-matrix by an EDTA-PDCA eluent. For the IC with indirect UV-detection the eluent consisting of CuSO₄ or CuCl₂ was used to separate Na, K, Mg and Ca with baseline resolution within 10 min.The detection limits of metal ions with conductivity detection were found beween 0.5 g/l for Li and 8 g/l for Cs. They were 10 times more sensitive than those with indirect UV-detection.This IC-method was applied to determine alkali, alkaline earth and Mn ions in the water, food, ore-cinder and sole-brine samples with satisfactory results.Dedicated to Prof. Dr. G. Schulze on the occasion of his 60th birthday     

Simultaneous determination of seven metal ions in water samples by solid-phase extraction on polyacrylonitrile activated carbon fibres

A new solid-phase extraction method utilising polyacrylonitrile activated carbon fibres (PAN-ACFs) as adsorbent was developed for the preconcentration of trace metal ions prior to their determination by inductively coupled plasma optical emission spectrometry (ICP-OES). The PAN-ACFs oxidised with nitric acid were characterised by FT-IR, XRD, SEM and BET analysis. Then the resulting PAN-ACFs were used as solid-phase adsorbent for simultaneously determination of trace Al(III), Be(II), Bi(III), Cr(III), Cu(II), Fe(III) and Pb(II) ions in aqueous solutions. The influences of the analytical parameters on the recoveries of the studied ions were investigated. The optimum experimental conditions of the proposed method were pH: 6.0; eluent concentration and volume: 3.0 mL of 1.5 mol L^?1 nitric acid; flow rates of sample and eluent solution: 1.5 mL min^?1. The preconcentration factors were found to be 67 for Al(III), Bi(III); 83 for Cr(III), Cu(II), Fe(III) and 50 for Be(II), Pb(II). The precision of this method was in range of 1.5%~3.5% and the detection limit of this metal ions was between 0.06~1.50 μg L^?1. The developed method was validated by the analysis of a certified reference sample and successfully applied to the determination of trace metal ions in water samples with satisfactory results.     

Chromatography of Uranium on High-Performance Ion Exchangers

Abstract

The potential of high-performance liquid chromatography (HPLC) for the determination of U(VI) in ground waters and urine has been examined under a variety of HPLC experimental conditions. Conventional cross-linked and bonded-phase ion exchangers, both cation and anion, were studied with aqueous mobile phases containing tartrate, citrate, or α-hydroxyisobutyrate. The best chromatography was obtained on bonded-phase cation exchangers with an α-hydroxyisobutyrate eluent. The metal ions were detected either by visible spectrophotometry after a post-column reaction with a complexing reagent, or with a polarographic detector. Dectection after post-column reaction gave the best sensitivity; the detection limit (2 × baseline noise was 6 ng or 60 ng.ml^?1 for 100 μl samples. In-line trace enrichment was used to decrease detection limits and linear calibration curves were observed in the ranges studied; 0.5 to 50 ng.mL^?1 for ground waters and 25 to 400 ng.mL^?1 for artificial urine.     

Determination of iron and copper in seawater at pH 1.7 with a new commercially available chelating resin, NTA Superflow

The use of a commercially available chelating resin with NTA-type functional groups for concentration of trace metals from seawater is described. Trace metal recoveries from this NTA Superflow chelating resin are pH dependent. At a pH of ≤2 only iron(III) and copper are quantitatively recovered from the resin. Iron(II) cannot be quantitatively recovered from this resin below a pH of 5. However, oxidation of acidified seawater samples (pH 1.7) with H₂O₂ prior to loading onto the resin has been demonstrated to allow quantitative recovery of total dissolved iron. Deferrioxamine and Rhodoturlic Acid, two commercially available siderophores were used to investigate the effect of strong Fe(III)-binding organic ligands on the ability to retain iron at different pH values. Acidification of seawater samples to pH 1.7 dissociates the iron complexed to these organic ligands, thereby allowing total dissolved iron and copper to be determined. Acidified samples from Monterey Bay were analyzed by a flow injection method coupled to ICP-SFMS detection using the NTA Superflow resin in the pre-concentration step. Results from this study show that when seawater samples are stored acidified (pH 1.7) over time, a portion of iron(III) is reduced to iron(II), thus necessitating the use of H₂O₂ to reoxidize the Fe(II) to Fe(III) prior to analysis. Total dissolved concentrations of iron and copper can be directly obtained on seawater samples at pH 1.7 with this method, eliminating the need to buffer the sample to a higher pH prior to column loading. This resin has the potential to be used in shipboard or in situ flow injection methods.     

螯合离子色谱法分析复杂基体中痕量金属离子的研究

发展了应用螯合离子色谱法分析复杂基体中痕量金属离子的新方法。针对不同的检测目的,利用螯合柱（ＭｅｔＰａｃＣＣ－１）和浓缩柱（ＴＭＣ－１）,采用适当的洗脱液在线将基体中的阴离子、一价阳离子、碱土金属离子以及其它干扰离子除去,同时,浓缩富集待测的痕量金属离子,然后再选择适当的梯度淋洗体系,在含有双功能基的分析柱上分离Ｐｂ,Ｃｕ,Ｃｄ,Ｃｏ,Ｚｎ和Ｎｉ等过渡金属离子和１４种镧系金属离子,继而用在线柱后衍生和光度法检测。方法简单快速,样品经适当的酸消解成溶液后即可进样,灵敏度高,检测限为１０－９级甚至更低。     

Determination of Metal Ions by High Performance Liquid Chromatography

The mixture of metal ions [Bi(III), Fe(III), Fe(II), Cu(II), Zn(II), Ni(II), Co(II), Pb(II), Cd(II), Mn(II)] were separated in the bonded-phase strong cation exchange column (Vydac-401 SA) and monitored at 540 nm after a postcolumn reaction with 4-(2-pyridylazo)-resorcinol (PAR). Citrate, tartrate, lactate and α-hydroxyisobutyrate buffer were used as eluent and it has been found that the elution order of some metal ions were changed with different eluents. The detection limits and the calibration curves of metal ions were also studied.     

Solid phase extraction of trace metals in water and leafy vegetables using a resin functionalized with potassium 2-benzoylhydrazinecarbodithioate and determination by ICP–AES

A solid phase extraction method for the determination of Cu(II), Mn(II) and Zn(II) metal ions in natural water and leafy vegetable samples by ICP-AES was developed. The method was based on the sorption of metal ions onto Amberlite XAD-16 functionalized with a new chelating ligand potassium 2-benzoylhydrazinecarbodithioate (Amberlite XAD-16-PBHCD) and elution with nitric acid. The optimum experimental conditions for the quantitative sorption of the three metal ions, namely, effect of pH, sample volume, flow rate, concentration of eluent, sorption capacity, kinetics of sorption, and the effect of diverse ions on the sorption of analytes have been investigated. All the metal ions were quantitatively retained by the functionalized resin at pH 5.0 and sorbed metals could be eluted with 2.0?M HNO₃. The detection limits were 5.6, 4.5 and 1.8?µg?L^?1 for Cu(II), Mn(II) and Zn(II), respectively. The developed method was applied for the determination of Cu(II), Mn(II) and Zn(II) in water and leafy vegetable samples.     

Acetohydroxamate Resin as Column Packing for Ion Chromatography

A chelating resin with acetohydroxamate functional groups was synthesized and used as the stationary phase in ion chromatography for the determination of copper. As the reaction mechanism was mainly complexation, the coordination behavior of the synthesized resin toward Cu(II) was studied by means of EPR, IR and electronic spectrometry and potentiometry. The kinetic study shows that the resin is suitable for use in ion chromatography. We employed a resin column 250 mm long by 3 mm I.D. in conjunction with a mixture of hydrochloric acid and acetone as mobile phase for the determination of Cu(II). Detection of the chromatography system was carried out via post-column derivatisation of the column effluent with PAR at 520nm. The detection limit is 0.22ppm, and the relationship was linear in the range 0.25-1.20ppm. We investigated the effect of other metal ions, As(V), Cd(II), Cr(III), Hg(II), Ni(II), Pb(II) and Zn(II), or foreign ligands, EDTA, ascorbic acid, humic acid or sodium chloride on the determination of Cu(II) ion. A concentration column packed with acetohydroxamate resin combined with the above separation system was also used to determine of copper ion; the dynamic range is 2-15 ppb and the detection limit is 0.70ppb. The proposed system was applied to the analysis of Cu(II) in sea water.     

Use of 1-(2-pyridylazo)-2-naphthol as the post column reagent for ion exchange chromatography of heavy metals in environmental samples

Ion exchange chromatography (IEC) using a bi-functional column (quaternary ammonium and sulfonate groups), followed by post-column reaction (PCR) with 1-(2-pyridylazo)-2-naphthol (PAN), was used to separate and quantitate Cu(II), Ni(II), Zn(II), Co(II), Cd(II), Mn(II) and Hg(II) at low concentration levels. IEC-PCR separation was achieved within 14 min using the mobile phase containing 3 mmol L^− 1 2,6-pyridinedicarboxylic acid (PDCA) and 3 mmol L^− 1 oxalate at pH 12.5. Effects of pH as well as PAN, detergent and chloride ion concentrations during post-column reaction on detector response were examined. Detection limits were less than 4.5 μg L^− 1 for all metals except Hg(II) (19 μg L^− 1) using spectrophotometric measurements at 550 nm. Analytical validations showed good linearity for detection up to 6.0 mg L^− 1, with R² higher than 0.99. Precisions based on retention time evaluation for intra-day and inter-day measurements with the relative standard deviation (RSD) were less than 2.9% and 3.6%, respectively. The method gave good accuracy with the recoveries ranged from 80.5 to 105% for all metal ions studied. The proposed method was applied to the analysis of metal ions in environmental samples (leachate, soil and sediment) in Northeastern Thailand. The results were in good agreement with atomic spectroscopic measurements on the same samples.     

Synthesis of a rare‐metal adsorbing polymer by three‐component polyaddition of diamines,carbon disulfide,and diacrylates in an aqueous/organic biphasic medium

Three‐component polyaddition of diamines, carbon disulfide (CS₂), and diacrylates in an aqueous/organic biphasic medium produced a polymer capable of adsorbing rare metals. By using a 1:1 mixture of toluene and H₂O, the polyaddition reaction of 1,3‐di‐4‐piperidylpropane (1), CS₂, and 1,6‐hexanediol diacrylate (2) proceeded efficiently in the presence of Et₃N to produce a poly(dithiourethane‐amine) with a high proportion of dithiourethane units almost quantitatively. Quantitative formation of 1‐CS₂ adducts in the aqueous phase was followed by efficient reaction with diacrylate at the biphasic interface. The resulting poly(dithiourethane‐amine) adsorbed Pd(II) and Pt(IV) efficiently under acidic conditions due to the high affinity of thiocarbonyl sulfur atoms for soft metal ions. The polymers showed highly selective adsorption of Pd(II) from a mixture of metal ions [Pd(II), Cr(III), Cu(II), Fe(III), Mn(II), Pb(II), and Zn(II)], indicating their potential utilization for selective recovery of rare‐metals. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010