Enthalpy characteristics of dilute solutions of acetonitrile

The enthalpies of mixing of acetonitrile with formamide,N-methylformamide,N,N-dimethylformamide, and hexamethylphosphoric triamide were measured in the temperature interval from 283.15 to 328.15 K. The enthalpy coefficients of binary and ternary interactions were calculated by the methods of the McMillan-Mayer theory. The contributions to the enthalpy of solution due to the formation of a cavity in the solvent, Δ_cav H°, and those due to the interaction of the solute with the solvent, Δ_int H°, were determined. The enthalpies of the specific and non-specific solvation of acetonitrile in the corresponding amides were calculated. Specific interactions were found to contribute the most to the solvation enthalpy of acetonitrile. The obtained values were compared with analogous values for solutions of acetonitrile in water and alcohols. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 289–293, February, 1997.     

The investigation of the electronic effects of polyfluoro-aryl group by means of nmr spectroscopy

The relationship between NMR ¹⁵N, ¹⁷O, ³¹P, ⁷⁷Se, ¹³C spectral parameters and electronic structure of number of polyfluoroaromatic compounds has been discussed. The increase of the nuclei shielding has been found in all classes of investigated polyfluorinated compounds in respect to the corresponding hydrocarbon analogues. That effect has been discussed in terms of decrease of the conjugation between the unshared electron density of heteroatoms and the π-system of polyfluorinated benzene ring. The conductivity of substituent electronic effects on the π-system of the polyfluoroaryl group by the heteroatom has been estimated from NMR ¹³C data. The sensitivity of nuclei shielding towards interamolecular electronic effects has been noticed to increase from oxygen to selenium and the analysis of the influence of the intramolecular electronic effects on the ¹⁷O and ⁷⁷Se shifts has been given. The influence of the substituents either in pentafluorophenyl ring or adjacent to heteroatom have been shown to correspond those in the hydrocarbon analogues.The conclusion about the influence of polyfluoroaryl group on the character of bonds between different atoms in functional group has been made from the NMR ¹⁷O and ¹⁵N data for aromatic nitro-derivatives. Polyfluorophenyl group in respect to phenyl one deshields the oxygen atom and shields the nitrogen atom. The same effect of pentafluorophenyl group has been observed by other spectral methods.The different screening of ¹⁷O, ¹⁵N, ³¹P and ⁷⁷Se nuclei due to the action of substituents adjacent to the element and variation of the coordination number of heteroatom have been used to the solvation of a number of problems in chemistry of the heteroanalogues of carbenium ions and the detail investigation of the mechanism of electrophylic substitution in the field of polyfluoroaromatic compounds.     

Evaluation of the effect of silicon on the carbonization process of Colombian semi-anthracites

The environmental impacts associated with the exploitation and transformation of fossil resources aggravate the planet's situation in terms of climate change. Due to this, this paper studies an alternative use of mineral coal as a precursor to obtaining new materials with different properties to the starting coals. The thermal degradation of two Colombian semi-anthracites is analyzed through the thermogravimetry (TG) technique coupled to a Fourier transform infrared spectroscopy (FTIR) equipment from room temperature (25 °C) to 900 °C, at a heating rate of 10 K min^?1 in an inert atmosphere. The catalytic effect of the addition of silicon to these samples before being subjected to a carbonization process is evaluated during this process. The results indicated that the primary reaction occurs in the temperature range between 400 and 680 °C, where the highest mass loss rate was observed. At the end of the heating process, the TG profile of the samples with silicon addition showed losses between 14.33 and 18.82% in mass, these values being slightly higher compared to the starting and demineralized samples. The release of water, light gases such as CO₂, CH₄, and species such as toluene, phenol and formic acid was identified in most of the samples. The presence of silica seems to favor the release of all these species, being more evident in one of the semi-anthracites studied. According to the results obtained, it is proved that the presence of silicon in samples subjected to carbonization processes has a catalytic effect that improves some characteristics of the new materials obtained, thus contributing to the use of carbon to get new materials.

     

Viscosity of aqueous solutions of polysaccharides and hydrophobically modified polysaccharides: Application of Fedors equation

Amphiphilic polysaccharides have been obtained by hydrophobic modification of a neutral bacterial polysaccharide, dextran. Various amounts and types of aliphatic hydrocarbon groups have been attached to dextran.The solution behaviour of unmodified dextran samples and amphiphilic dextran derivatives is characterized by viscometric measurements. The overall viscosity behaviour of unmodified polysaccharides is described up to C × [η] = 3, using the equation of Fedors [Fedors RF. Polymer 1979;20:225] which involves only a concentration parameter. The latter is shown to depend on the hydrodynamic volume of the macromolecules in solution.The equation of Fedors is shown to conveniently estimate the viscosity behaviour of amphiphilic dextran derivatives up to C × [η] = 1. The interdependence between Fedors parameter and other viscometric characteristics (intrinsic viscosity, Huggins coefficient) is evidenced. These results are extended to the data of other authors.     

Theoretical study of formation mechanism of aluminosilicate in the synthesis of zeolites

Abstract  The condensation of silicic acid with aluminate in alkaline environment, the essential reaction of zeolite synthesis, is studied using the density functional theory, with the hybrid functional B3LYP in conjunction with the 6-311++G(d, p) basis set. The Si(OH)₄ monomer and Al(OH)₄⁻ anion are used as the reactant models to study the condensation pathway in basic solution. The solvent effect is included by the COSMO-RS model. The study includes the complete geometry optimization and frequency calculation of reactants, products, reaction intermediates, and transition states, as well as the calculation of the activation energy of the different pathways involved. The intrinsic reaction coordinate method is used to verify the reactant and product corresponding to the transition state. The calculation shows that the formation of Si–O–Al linkage can proceed via two possible reaction pathways. The first is a single-step process, in which the formation of SiO···Al bond and removal of water are synchronous, with the activation energy of 83.7 kJ/mol. The second is a stepwise route, in which the AlO···Si bond is first formed to give a 5-coordianted Si intermediate, and then water is removed to yield a dimer aluminosilicate, with the barriers of 62.7 and 69.3 kJ/mol for the two steps, respectively. Index Abstract   Theoretical study of formation mechanism of aluminosilicate in the synthesis of zeolites Guo-Feng Jiao, Min Pu, Biao-Hua Chen      

Photocatalytic activity of nanoparticles of metal sulfides in the degradation of organic dyes

The photocatalytic degradation of dyes at the nanosized sulfides of transition metals in aqueous solutions was investigated. The rate of degradation increases with decrease in the synthesis temperature of the nanoparticles and with the addition of alcohol. The substitution of Cd²⁺ cations by Ag⁺ or Cu²⁺ leads to a decrease in the photoactivity of the CdS, while substitution by In³⁺ leads to an increase. The substitution of Ni²⁺ and Co²⁺ cations in the corresponding sulfides by Cd²⁺ leads to an increase in the rate of degradation. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 5, pp. 276–280, September–October, 2006.     

Dilation of polyethylene by sorption of carbon dioxide

The dilation of low-density polyethylene accompanied by the sorption of CO₂ was measured by microscopy under pressures up to 50 atm at temperatures from 25 to 55°C. The dilatometry measurement, which is also applied to the determination of the thermal expansion coefficient, is directly performed by a cathetometer. The dilation of LDPE by sorbed CO₂ is linear with concentration. The buoyancy correction is described for the CO₂ sorption isotherms in LDPE. The partial molar volume of CO₂ in LDPE, calculated from the dilation and the sorption isotherms, is almost independent of temperature.     

Enthalpy characteristics of dilute solutions of amides in acetonitrile

The enthalpy of mixing of formamide,N-methylformamide,N,N-dimethylformamide, and hexamethylphosphoric triamide with MeCN was measured in the 283–328 K range. The enthalpic coefficients of the binary and ternary interactions between the amide molecules are calculated within the framework of the McMillan-Mayer theory. The contributions to the enthalpy of dissolution due to cavity formation in the solvent (Δ_cav H ⁰) and due to solute-solvent interaction (Δ_int H ⁰) were determined. The enthalpies of specific and nonspecific solvation of amides in MeCN were calculated. The main contribution to the enthalpy of solvation of formamide andN-methylformamide is from specific interactions, while forN,N-dimethylformamide and hexamethylphosphoric triamide it is from nonspecific interactions. The values obtained are compared with those for solutions of the amides mentioned in water and methanol. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1730–1735, October, 1993.     

Kinetics and mechanism of thermal decomposition of hydroxylammonium nitrate

The kinetics of thermal decomposition of melted hydroxylammonium nitrate have been investigated by the rate of heat production in the temperature range 84.8–120.9°C. The decomposition proceeds with autocatalysis and up to 60 % of conversion the rate of the process increases proportionally to the square of the degree of decomposition. The initial rate is proportional to the square of the concentration of HNO₃ formed due to dissociation of the salt. The activation energy of this process is 15.3±1.8 kcal/mol. It is suggested that the initial stage the process proceeds via interaction between N₂O₃ and NH₃OH⁺, whereas the subsequent acceleration is due to oxidation of NH₃OH⁺ by nitrogen oxides formed as well as by nitrous acid.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 1897–1901, November, 1993.     

The mechanism of cooxidation of isobutyraldehyde and octene-2

The mechanism of isobutyraldehyde-octene-2 cooxidation at 20°C has been investigated. The ratio of cis to trans epoxides in the reaction products shows that, at aldehyde concentrations lower than 1.0M, the epoxide is formed mainly by a radical route. The difference in the ΔH of formation of cis and trans epoxides is around 0.8 kcal/mole at 20°. The isobutyraldehyde involved in the radical epoxidation chain has been found almost quantitatively to be isopropylhydroperoxide, which is formed through the decarboxylation of i-PrCO₂· radicals, addition of oxygen, and abstraction of hydrogen atoms from the aldehyde. A rate constant of about 14 M^?1 sec^?1 at 20° has been determined for the latter reaction. The chain length for the cooxdination reaction decreases from 75 to 20 as the isobutyraldehyde concentration goes from 1.0 to 0.3M. The termination step seems to involve mainly the interaction of two i-PrO₂ · radicals. The cooxidation of octene-2 with pivalaldehyde follows a similar mechanism, but the chain length is about ten times higher under the same experimental conditions.     

Determination of neutron fluence using the plot of isotope variation of cadmium and gadolinium

The method described to determine the neutron fluence is based on the plot of the isotopic variation of Cd and Gd subjected to neutron irradiation in a research reactor. The isotopic ratios are measured by thermal ionization mass spectrometry. The results indicate that the fluence values obtained, using the variation in the ratios¹¹⁴Cd/¹¹³Cd,¹⁵⁶Gd/¹⁵⁵Gd and¹⁵⁸Gd/¹⁵⁷Gd show standard deviations varying from 0.3 to 6.6%. These values agree with the extrapolated values calculated using the short time Au activation method. The method appears to be useful for determining paleo neutron flux in natural samples and irradiated fuels.     

Mechanism of the decomposition of cobaltous compounds in vacuo

The decomposition of cobaltous compounds (nitrate, hydroxide, carbonate, oxalate and oxyhydroxide) in vacuo has been investigated by magnetic methods and thermogravimetry. The mechanism is shown to be similar to that in air and begins with the formation of Co³⁺ ions in octahedral coordination. The formation of different final products (Co₃O₄, CoO and Co) has been attributed to the nature of the initial cobaltous compound. The results are in agreement with thermodynamic calculations.     

The solubility and kinetics of decomposition of ozone in aqueous solutions of nitrates

The influence of the concentration of NaNO₃ on the solubility of ozone in water was studied at 20, 30, and 40°C. The solubility coefficients of ozone were calculated, and the Henry constants and Sechenov coefficients determined. The Sechenov coefficients (K _c ) were found to decrease insignificantly as the temperature increased. The kinetics of dissolved O₃ transformations was analyzed. The decomposition of ozone was described by a pseudofirst-order equation with respect to salt concentration. The rate constant (k _c ) for the decomposition of ozone in the presence of NaNO₃ was found to be 3.5 × 10^?4 l mol^?1 s^?1.     

Optimization of the process parameters of synthesis of vinblastine imprinted polymer

Molecularly imprinted polymers (MIPs) are tailor-made polymers with high selectivity for the template molecule. This selectivity arises from the synthetic procedure followed to prepare the MIP. In this work, the influence of process parameters on the preparation of vinblastine (VLB) imprinted polymers was presented. In the procedure of polymerization, VLB (0.1 mmol) was used as the template molecule and a commonly used initiator, azobisisobutyronitrile (AIBN), was employed to initiate the reaction at 60 °C. The influence of the following parameters was investigated: the moles of functional monomer (MAA, 0.3-1.0 mmol), the moles of cross-linker (EDMA, 1.5-5.0 mmol) and the porogenic solvent (toluene or acetonitrile). A mathematical method of uniform design was applied to optimize these selected parameters in order to increase the selectivity of MIP for template molecule. The experimental data were analyzed to obtain the regression model and the optimal conditions were achieved by optimization with uniform design software. The MIP was synthesized under the optimal conditions that 1.0 mmol of MAA and 5.0 mmol of EDMA copolymerized in toluene in the presence of 0.1 mmol of VLB. After removal of the template molecule, the obtained MIP was then employed as the sorbents of solid-phase extraction (SPE) to separate VLB from Catharanthus roseus extract. The results showed that the polymer exhibited high affinity to the template molecule and could separate and enrich VLB from C. roseus extract effectively. The recovery of VLB on the optimal MIP was 89.00%, which agreed closely with the predicted recovery. Therefore it is possible to further improve the nature of the polymer by optimizing the polymerization parameters with the method of uniform design.     

Kinetics of biodesulfurization of a high-sulfur coal

The apparent activation and deactivation energies and the corresponding frequency factors of coal desulfurization byThiobacillus ferrooxidans have been determined to be ΔE _a = 60.9 kJ,A _a = 1.45 s^-1 and ΔE_d = 178.3 kJ,A _d = 5.65×10²⁷ s^-1, respectively. The thermo-dynamic values (AG^?, ΔH ^?, and ΔS^?) of the activated complex were calculated. Kinetic parameters of the Monod equation were determined to beV _m = 55.9 mg dm^-3 h^-1 andK = 24.1% pulp density. The maximum rate of desulfurization of coal was found to beV _m = 55.7 mg dm^-3 h^-1 for the particle size. The generalized second order regression equation relating the yield of desulfurization to the leaching parameters was shown to adequately predict coal extraction data and optimum values of process variables. Tank leaching studies using optimum conditions resulted coal desulfurization about 90%. The iron hydrolysis reactions involving the formation of mono- and poly-nuclear, hydroxo- and sulfato complexes of amorphous and crystalline precipitates were discussed.     

The Effect of Active Carbon on the Kinetics of Polymerization of Methyl Methacrylate

Rates of 2–2¹?azobisisobutyronitrile initiated polymerization of methyl methacrylate in benzene were determined at 77.2, 65.0, and 50.0°C. The variation of molecular weight of the polymer with temperature and conversion was also studied. At a fixed conversion of 2.0%, the molecular weight decreased from 2.05 × 10⁵ at 50°C to 1.4 × 10⁵ at 77.2°C. The ratio of the propagation rate coefficient to the square root of the termination rate coefficient was found to be 0.61, 0.397, and 0.374 at 77.2, 65.0, and 50.0°C, respectively, with an uncertainty of ±0.5°C in temperature. The effect of active carbon on the rates of polymerization at 77.2°C was measured. Rates of polymerization decreased in the presence of active carbon. For example, the initial rate of polymerization decreased from 7.8 × 10^?4 mole/(liter min) to 4.6 × 10^?4 mole/(liter min) when the carbon concentration was varied from 0 to 9.65 g/liter. The molecular weight of the polymer increased from an average of 1.4 × 10⁵ in the absence of carbon to 1.5 × 10⁵ when carbon was present.     

Experimental Study of the Effect of Temperature,Pressure, and Concentration on the Viscosity of Aqueous KBr Solutions

The viscosity of five (0.1240, 0.2378, 0.4645, 0.9440, and 2.2310 mol⋅kg⁻¹) binary aqueous KBr solutions have been measured with a capillary flow technique. Measurements were made at pressures up to 30 MPa for the temperature range 298 to 577 K. The total uncertainties of the viscosity, pressure, temperature, and composition measurements were estimated to be less than 1.6%, 0.05%, 15 mK, and 0.02%, respectively. The temperature and pressure coefficients of the viscosity of KBr(aq) were studied as a function of molality and temperature. The measured viscosities were compared with data, predictions and correlations previously reported in the literature. The viscosity data were used to accurately calculate the physical-meaningful parameters (viscosity A- and B-coefficients) of the extended Jones-Dole equation for the relative viscosity (η/η ₀). Various theoretical models {absolute rate theory, Tammann-Tait-Gibson (TTG) model, and extended Einstein model} were used to accurately represent the measured viscosities. Values of hydrodynamic molar volume V _k (effective rigid molar volume of the salt) were calculated using the present experimental data. The high-pressure viscosity measurements were used to test the predictive capability of the TTG model.     

Theoretical calculation of vertical ionization potentials of B2H6 by means of ΔESCF procedures

The vertical ionization potentials (IPS ) of B₂H₆ are calculated by means of the ΔE_SCF procedure, within the scheme of ab initio LCAO-MO-HF-SCF . The basis set used is LEMAO -3G. The scaling factors of the various atomic orbitals for the ground state and for the various hole states are optimized independently. The iteration procedure is specially designed to avoid the changes of the symmetry of the remaining occupied orbitals. The 1 ag (B1s) hole is found to be localized. The vertical IP of the 1 ag electron is calculated to be 196.5 eV, in fair agreement with experimental value. The D_2h symmetry is thereby broken and reduced to C_2V symmetry. The valence holes are found to be delocalized. The calculated vertical IPS are: 21.781, 16.974, 14.842, 14.389, 13.599, and 12.380 eV for the 2ag, 2b1u, 1b3u, 1b2u, 3ag, and 1b3g electrons, respectively. The agreement with experimental values is much better than the Koopmans' values. All these results are in favor of the concept that the nature of the convelent bond should be considered as a result of the mutual interactions and mutual conditioning between the wave nature of the electronic motion on the one side and the various attractive and repulsive factors on the other side.     

Kinetics of the thermal decomposition of dinitramide

The kinetic regularities of the thermal decomposition of dinitramide in aqueous solutions of HNO₃, in anhydrous acetic acid, and in several other organic solvents were studied. The rate of the decomposition of dinitramide in aqueous HNO₃ is determined by the decomposition of mixed anhydride of dinitramide and nitric acid (N₄O₆) formed in the solution in the reversible reaction. The decomposition of the anhydride is a reason for an increase in the decomposition rates of dinitramide in solutions of HNO₃ as compared to those in solutions in H₂SO₄ and the self-acceleration of the process in concentrated aqueous solutions of dinitramide. The increase in the decomposition rate of nondissociated dinitramide compared to the decomposition rate of the N(NO₂)₂ ⁻ anion is explained by a decrease in the order of the N−NO₂ bond. The increase in the rate constant of the decomposition of the protonated form of dinitramide compared to the corresponding value for neutral molecules is due to the dehydration mechanism of the reaction. For Part 1, see Ref. 1. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 41–47, January, 1998.