羧酸和环氧化合物加成酯化反应的新型催化剂及其应用

研究了取代呋喃甲酸,取代水杨酸和脂肪酸铬类型螯合物作为羧酸和环氧化合物加成酯化反应的新型催化剂,并以其中的5-叔丁基呋喃甲酸铬作催化剂研究了环氧乙烷上的取代基和羧酸的酸性对反应速度的影响。合成了一系列羧酸β-羟基丙酯类衍生物。     

Rh(Ⅰ),Co(Ⅰ)和Ru(Ⅱ)双齿磷氢化物的合成.结构表征和催化加氢活性

膦配位的过渡金属氢化物被看作是烯烃及其他一些不饱含有机化合物催化加氢反应及氢甲酰化反应的催化活性物种,关于它们的结构与催化活性关系的研究,有着重要的理论意义和实际意义,通常单齿膦配位表现出较高的催化活性,而不同的金属中心在催化活性和选择性上也表现出明显的差别,反映了催化功能与催化活性物种的电子结构和空间结构之间存在着依存关系.膦配体过渡金属氢化物,通常是以它们的相应卤化物经氢化锂铝或硼氢化钠或肼还原得     

环氧树脂潜伏性固化促进剂的研究

对环氧树脂/桐油酸酐/乙酰丙酮钕体系的热固化反应进行了研究。用DSC、TBA和固化仪等手段测定了凝胶化时间和表观反应活化能,计算了反应动力学参数。结果表明,乙酰丙酮钕对体系的固化具有潜伏性促进作用。     

环氧/酸酐/DMPA体系固化动力学与溶解性研究

在环氧/酸酐固化体系中引入4-二甲氨基吡啶(DMPA)作为酯交换反应催化剂和固化反应促进剂,以制备具有动态交联网络的环氧树脂。用差示扫描量热仪(DSC)对环氧/酸酐/DMPA体系的固化行为进行了研究,考察了催化剂的含量和固化剂比例对环氧/酸酐/DMPA体系固化行为的影响和固化动力学。通过乙二醇溶解实验,研究交联网络中的可交换键。结果表明反应体系中有高温和低温两种固化机理发生反应,催化剂和固化剂含量较少时,固化反应温度高,固化反应中含较多环氧自聚反应,不利于酯交换反应,溶解效果差;反之,固化反应温度向低温移动,利于酯键的形成,样品的溶解速度就越快。当环氧/酸酐为1:1.5,催化剂用量为3%时,具有较好的溶解性能。     

钼(Ⅵ)螯合物催化辛烯-1环氧化

本文研究了在钼(Ⅵ)螯合物催化下,用叔丁基氢过氧化物进行辛烯-1环氧化反应动力学。比较了不同配位基的钼(Ⅵ)螯合物催化性能的差异。配位基与钼(Ⅵ)的结合愈不牢固,反应速度常数愈大,而催化剂稳定性愈差。当存在过量给予体时,钼(Ⅵ)螯合物因解离受到抑制,则没有催化活性。如给予体适量,既可以保持催化剂的活性,又可增加催化剂的稳定性。     

酸酐固化环氧树脂/蒙脱土复合材料的等温固化动力学

用等温差示扫描量热法(DSC)研究了酸酐固化环氧树脂/蒙脱土复合材料的等温固化过程，考察了未处理的蒙脱土(MMT)和有机蒙脱土(OMMT)对环氧树脂固化动力学的影响. 实验表明， 环氧树脂的固化过程包含自催化机理，加入蒙脱土没有改变固化反应机理. 用Kamal方程对该体系的固化过程进行拟合，得到反应级数m、n，反应速率常数k1、k2，总反应级数(m + n)在2.4～3.0之间. MMT的加入使环氧树脂体系的k1、k2有所降低，而OMMT的加入对体系的k1、k2影响较为复杂，加入蒙脱土对环氧树脂固化体系的活化能影响较小.     

酰氧基硅烷和环氧化合物的开环反应动力学及其机理

酰氧基硅烧和环氧化合物的开环反应可用于环氧树脂的改性.但对该反应的研究不多.我们发现5-叔丁基呋喃甲酸铬是酰氧基硅烷和环氧化合物开环反应的较好催化剂,认为有必要研究这一催化反应的动力学和反应机理.我们以三甲基乙酰氧基硅烷和环氧氯丙烷为模型化合物,研究了在5-叔丁基呋喃甲酸铬的存在下,以甲苯为溶剂,酰     

基于松香酸酐的环氧树脂体系固化动力学及TTT图绘制

研制了基于松香酸酐固化剂的生物质环氧树脂体系,采用全动态DSC法研究了树脂体系的固化反应动力学,通过半经验的唯象模型拟合得到了固化反应参数,活化能Ea为59.68 kJ/g,指前因子A0为1.28×1015s-1,反应级数n为2.483,由此建立了体系固化温度/时间/固化度间的关系;采用恒温DSC及DMA方法测试玻璃化转变温度,应用DiBenedetto经验方程拟合得到了玻璃化转变温度与固化度间的关系.应用锥板旋转黏度计测试了树脂体系不同温度下的凝胶时间,通过线性回归分析得到了凝胶时间与温度之间的关系.由唯象模型和DiBenedetto方程分别计算得到凝胶时的固化度为0.386,玻璃化转变温度为26.22°C.由上述工作绘制了基于松香酸酐生物质树脂体系的TTT(time-temperature-transition diagram)固化图,可确定树脂体系在不同温度任意时间下的状态.     

烯烃齐聚锆及铬族均相催化剂研究进展

综述近年来烯烃齐聚锆及铬族均相催化剂研究的最新成果，分别介绍锆及铬类均相催化体系的特色和研究侧重点，并对各种催化体系中不同中心金属及其配体对催化活性和选择性的影响进行了分析比较。     

热致性液晶聚合物的种类对液晶/环氧树脂共混物固化反应动力学的影响

采用等温DSC固化动力学研究方法,用自催化动力学模型对反应型热致性液晶聚合物/环氧树脂共混体系进行研究.结果表明,EP/DDS未改性体系,在α＜40%范围遵循自催化反应机理;EP/DDS/LCPU共混改性体系,在α＜60%范围遵循自催化动力学反应机理,而且自催化反应速率和非催化反应速率均大于未改性体系,表明反应型热致性液晶聚合物的活性基团对固化反应起到了催化促进作用;EP/DDS/PHBHT共混改性体系能够较好符合n级反应机理,固化反应的活化能较大,说明没有反应基团的液晶聚合物(PHBHT)对固化反应无明显促进作用.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.