Synthesis and investigation of the luminescent properties of carbon doped lanthanum aluminate (LaAlO3) for application in radiation dosimetry

LaAlO₃ single crystals grown under hydrothermal conditions and co-doped with Ce and Dy atoms have been recently reported to show high thermoluminescent (TL) outputs for ultraviolet (UV) radiation fields (Oliveira et al., 2011). Due to this property, they have been considered for further investigation for applications in UV dosimetry. Encouraged by these results, we start an investigation about the TL properties of polycrystalline LaAlO₃ grown by an alternative method. In this method, equimolar amounts of Al₂O₃ and La₂O₃ are sintered, producing polycrystalline LaAlO₃ powder. Polycrystals doped with amounts of carbon ranging from 0.0 to 5.0 at.% were synthesized by sintering under hydrogen reducing atmosphere. After irradiation with a UV commercial lamp, the best TL outputs were observed for the undoped sample. The recorded TL glow curves show a main TL peak centered at 175 °C. The TL emission spectrum show a broad emission peak centered at 634 nm and another three narrow peaks centered at 724 nm, 738 nm and 754 nm, respectively. The undoped material show a huge TL output response for UV spectral irradiances ranging from 0.04 to 1.68 mJ cm⁻² that can be fitted by a 2nd order polynomial regression. The investigation demonstrates that undoped polycrystalline LaAlO₃ crystals sintered under reducing atmosphere are very attractive to be investigated as high sensitivity ultraviolet TL dosimeters.     

Thermoluminescence and opitical absorption of BaF2 crystals

Abstract

Nominally pure and Dy-doped BaF₂ crystals were investigated concerning their optical absorption (OA) and thermoluminescence (TL) properties. Peaks at 120—150 and 200°C were observed for a heating rate of 1.7°C/s. The TL response for γ-rays and the TL emission spectra were obtained for these peaks. Except for the purest crystal, all BaF₂ crystals produced OA bands before irradiation typical of Ce³⁺ ions. After irradiation, Dy doped crystals showed bands due to Dy²⁺ ions. A nominally pure sample gave bands related to Ce²⁺ ions and photochromic centers of Ce³⁺ ions. and photochromic centres of Ce³⁺ ions. The correlation between some OA bands and TL peaks is discussed.     

Pulsed-laser crystallization and epitaxial growth of metal-organic films of Ca-doped LaMnO3 on STO and LSAT substrates

Ca-doped LaMnO₃ (LCMO) thin films have been successfully prepared on SrTiO₃ (STO) and [(LaAlO₃)_0.3-(SrAlTaO₆)_0.7] (LSAT) substrates using the excimer laser assisted metal-organic deposition (ELAMOD) process. The crystallization and the epitaxial growth of the amorphous metal-organic LCMO thin films have been achieved using a KrF excimer laser irradiation while the substrates were kept at constant temperature of 500 °C. Epitaxial films were obtained using laser fluence in the interval of 50-120 mJ/cm². The microstructure of the LCMO films was studied using cross-section transmission electron microscopy. High quality of LCMO films having smooth surfaces and sharp interfaces were obtained on both the STO and the LSAT substrates. The effect of the laser fluence on the temperature coefficient of resistance (TCR) was investigated. The largest values of TCR of the LCMO grown on the LSAT and the STO substrates of 8.3% K⁻¹ and 7.46% K⁻¹ were obtained at different laser fluence of 80 mJ/cm² and 70 mJ/cm², respectively.     

Dosimetric properties of rare earth doped LiCaBO3 thermoluminescence phosphors

Lithium Calcium borate (LiCaBO₃) polycrystalline thermoluminescence (TL) phosphor doped with rare earth (RE³⁺) elements has been synthesized by high temperature solid state diffusion reaction. The reaction has produced a very stable crystalline LiCaBO₃:RE³⁺ phosphors. Among these RE³⁺ doped phosphors thulium doped material showed maximum TL sensitivity with favorable glow curve shape. TL glow curve of gamma irradiated LiCaBO₃:Tm³⁺ samples had shown two major well-separated glow peaks at 230 and 430 °C. The glow peak at 430 °C is almost thrice the intensity of the glow peak at 230 °C. The TL sensitivity of the phosphor to gamma radiation was about eight times that of TLD-100 (LiF). Photoluminescence and TL emission spectra showed the characteristic Tm³⁺ peaks. TL response to gamma radiation dose was linear up to 10³ Gy. Post-irradiation TL fading on storage in room temperature and elevated temperatures was studied in LiCaBO₃:Tm³⁺ phosphor.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Luminescence studies on swift heavy ion irradiated nanocrystalline aluminum oxide

Pellets of nanocrystalline aluminum oxide synthesized by a combustion technique are irradiated with 120 MeV Au⁹⁺ ions for fluence in the range 5×10¹¹-1×10¹³ ions cm⁻². Two photoluminescence (PL) emissions, a prominent one with peak at ∼525 nm and a shoulder at ∼465 nm are observed in heat treated and Au⁹⁺ ion irradiated aluminum oxide. The 525 nm emission is attributed to F₂²⁺-centers. The PL intensity at 525 nm is found to increase with increase in ion fluence up to 1×10¹² ions cm⁻² and decreases beyond this fluence. Thermoluminescence (TL) of heat-treated and swift heavy ion (SHI) irradiated aluminum oxide gives a strong and broad TL glow with peak at ∼610 K along with a weak shoulder at 500 K. The TL intensity is found to increase with Au⁹⁺ ion fluence up to 1×10¹³ ions cm⁻² and decreases beyond this fluence.     

Spectral properties of Nd-doped Sr3Ga2Ge4O14 crystal

Neodymium doped strontium gallogermanate crystals were grown successfully by the Bridgman technique. The linear thermal expansion coefficients for the c- and a-axes were measured as 5.8 × 10⁻⁶ °C⁻¹ and 6.5 × 10⁻⁶ °C⁻¹. Absorption spectra, and fluorescence spectra, as well as fluorescence decay curves of Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal, have been recorded at room temperature and used to calculate the absorption and stimulated emission cross-sections. Based on the Judd-Ofelt theory, three intensity parameters were obtained. The luminescent quantum efficiency of the ⁴F_3/2 level was determined to be approximately 73.8% for this material. Compared with other Nd³⁺-doped laser crystals, Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal displays special laser properties due to its disorder structure.     

VUV spectroscopy of pure and Tm-doped LicaAlF6 crystals

Nominally pure and Tm³⁺-doped LiCaAlF₆ crystals were grown by the Czochralski technique in a reducing atmosphere. The optical properties of transparent single crystals were studied using absorption and time-resolved luminescence spectroscopy in the VUV spectral range (330-100 nm). The strongest VUV emission peaking at 60 800 cm⁻¹ with a decay time of 5.6 μs (7 μs) at 300 K (7.4 K) was assigned to the spin-forbidden 4f¹¹5d-4f¹² transition of Tm³⁺. The fine structure observed in the VUV emission and corresponding excitation spectra indicate intermediate strength of electron-phonon coupling in this system. The efficient excitation of f-f emissions above 72 000 cm⁻¹, higher than the onset of f-d absorption at 63 000 cm⁻¹, is mainly caused by the F⁻ to Tm³⁺ charge transfer absorption. The nature of various host-related excitation processes in the energy transfer to the Tm³⁺ ions is discussed.     

Investigation of defect centres responsible for TL/OSL in MgAl2O4:Tb

Magnesium aluminate doped with Tb³⁺ (MgAl₂O₄:Tb³⁺) was prepared by combustion synthesis. Three thermoluminsence (TL) peaks at 120, 220 and 340 °C were observed. PL and TL emission spectrum shows that Tb³⁺ acts as the luminescent centre. Optically stimulated luminescence (OSL) was observed when stimulated by 470 nm blue light.Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the TL and OSL processes in MgAl₂O₄:Tb³⁺. Two defect centres were identified in irradiated MgAl₂O₄:Tb³⁺ phosphor by ESR measurements which was carried out at room temperature and these were assigned to V and F⁺ centres. V centre (hole centre) is correlated to 120 and 220 °C TL peaks and F⁺ centre (electron centre), which acts as a recombination centre is correlated to 120, 220 and 340 °C.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.     

Studies of the phosphorescence of polycrystalline hafnia

Persistent phosphorescence induced by ultraviolet light in polycrystalline HfO₂ and enhancement of the phosphorescence by sintering are investigated. The phosphorescence afterglow emission is in the 1.8-3.2 eV spectral range, with a peak at 2.53 eV. The afterglow intensity is significantly increased by sintering in either inert atmosphere or air. The afterglow light sum measured at room temperature for samples sintered at 1500 °C is more than an order of magnitude higher than that before sintering. In the temperature range −50 to 200 °C, three thermoluminescence (TL) peaks are observed near −10, 30, and 100 °C. The relative contribution of the low-temperature TL peak to the total TL intensity decreases after sintering, and this effect is more pronounced upon sintering in inert atmosphere. Conversely, the contribution of the TL peak near 100 °C increases after sintering. The enhancement of the afterglow by sintering is associated with the observed increase in the intensity of TL peaks at and above room temperature and attributed to an increase in the number of deep charge traps. The room-temperature afterglow time decay has a form consistent with the second-order mechanism, ∝(t₀+t)⁻ⁿ, and the best-fit values of both fitting parameters t₀ and n tend to increase with the sintering temperature.     

Electrical properties vs. microstructure of nanocrystallized V2O5-P2O5 glasses — An extended temperature range study

An electronically conducting nanomaterial was synthesized by nanocrystallization of a 90V₂O₅·10P₂O₅ glass and its electrical properties were studied in an extended temperature range from − 170 to + 400 °C. The conductivity of the prepared nanomaterial reaches 2 ? 10^− 1 S cm^− 1 at 400 °C and 2 ? 10^− 3 S cm^− 1 at room temperature. It is higher than that of the original glass by a factor of 25 at room temperature and more than 100 below − 80 °C. A key role in the conductivity enhancement was ascribed to the material's microstructure, and in particular to the presence of the large number of small (ca. 20 nm) grains of crystalline V₂O₅. The observed conductivity dependencies are discussed in terms of the Mott's theory of the electronic hopping transport in disordered systems. Since V₂O₅ is known for its ability to intercalate lithium, the presented results might be helpful in the development of cathode materials for Li-ion batteries.     

Crystallization of 21.25Gd2O3-63.75MoO3-15B2O3 glass induced by femtosecond laser at the repetition rate of 250 kHz

We report the formation of β′-Gd₂(MoO₄)₃ (GMO) crystal on the surface of the 21.25Gd₂O₃-63.75MoO₃-15B₂O₃ glass, induced by 250 kHz, 800 nm femtosecond laser irradiation. The morphology of the modified region in the glass was clearly examined by scanning electron microscopy (SEM). By micro-Raman spectra, the laser-induced crystals were confirmed to be GMO phases and it is found that these crystals have a strong dependence on the number and power of the femtosecond laser pulses. When the irradiation laser power was 900 mW, not only the Raman peaks of GMO crystals but also some new peaks at 214 cm⁻¹, 240 cm⁻¹, 466 cm⁻¹, 664 cm⁻¹ and 994 cm⁻¹which belong to the MoO₃ crystals were observed. The possible mechanisms are proposed to explain these phenomena.     

Spectroscopic analysis of Er transition in Mg/Er-codoped LiNbO3 crystal

We present a Judd-Ofelt spectroscopic analysis on the Mg/Er-codoped congruent lithium niobate (LiNbO₃) crystals. The Judd-Ofelt model is applied to the room temperature unpolarized absorption intensities of Er³⁺ ions on eleven transition bands to determine their intensity parameters: Ω₂=2.36×10⁻²⁰ cm², Ω₄=0.76×10⁻²⁰ cm², Ω₆=0.30×10⁻²⁰ cm² in Er:LiNbO₃ crystal heavily codoped with MgO. The radiative lifetime of ²H_9/2 becomes longer when MgO is added into Er:LiNbO₃ crystal. The experimental lifetimes are obtained using microsecond time-resolved spectra at 400 nm femtosecond pulse excitation to predict radiative quantum efficiency. Combining higher radiative quantum efficiency with longer radiative lifetime, we conclude that Mg/Er-codoped LiNbO₃ crystals are more suitable than Er: LiNbO₃ ones in laser materials.     

Point defects and orientation-dependent transport of matter and charge in iron-containing olivines

The variation of the oxygen content, x_O, of synthetic fayalite (Fe₂SiO₄) single crystals was investigated thermogravimetrically at 1130 °C as a function of the oxygen activity, a_O2 (= P_O2/P_O2° ≈ f_O2/f_O2° with P_O2° ≈ f_O2° = 1 bar ≈ 1 atm). It was found that x_O varies less in fayalite single crystals than in polycrystalline Fe₂SiO₄ studied earlier. The majority defects are most likely cation vacancies, (V_Me²⁺)″, ferric ions on M-sites, (Fe³⁺_Me²⁺), and ferric ions on Si-sites, (Fe³⁺_Si⁴⁺)′. Furthermore, the diffusion of iron in synthetic olivine single crystals ((Fe_xMg_1 − x)₂SiO₄) was studied at 1130 °C as a function of orientation, oxygen activity, and cationic composition. The observed oxygen activity dependencies suggest that cations move via different types of cation vacancies, most likely isolated vacancies, (V_Fe²⁺)″, and possibly neutral associates, {2(Fe³⁺_Me²⁺) ⋅ (V_Me²⁺)^′ ? ′}^x, the latter being minority defects. In addition, the electrical conductivity, σ, of fayalite single crystals was investigated as a function of orientation and oxygen activity within the stability field of fayalite at 1130 °C. The observed oxygen activity dependencies are compatible with (V_Me²⁺)^′ ? ′, (Fe³⁺_Me²⁺), and (Fe³⁺_Si⁴⁺)′ being the majority point defects at high a_O2 and with h^⋅ and e′ as the majority defects at low a_O2. The electrical conduction in fayalite is governed by contributions of electrons and holes. This extended point defect model for fayalite is also compatible with data for the variation of the oxygen content and for the iron tracer diffusion.     

Intense ultraviolet and blue upconversion emissions in Yb-Tm codoped stoichiometric Y7O6F9 powder

Stoichiometric Y₇O₆F₉ powder codoped with Yb³⁺-Tm³⁺ was synthesized via co-precipitation and subsequent calcining route. The results of X-ray diffraction and transmission electron microscopy reveal that when the calcining temperature is beyond 800 °C, orthorhombic YF₃ nanoparticles can be completely oxidized into orthorhombic Y₇O₆F₉ powder. Under the excitation of a 980 nm laser, Y₇O₆F₉ powder exhibits multicolor UC emission in regions spanning the UV to the NIR. In addition, the upconversion emission intensities of YF₃, Y₇O₆F₉ and Y₂O₃ powders were compared under the same dopant condition (Yb/Tm=5/0.5 mol%). The low phonon energy revealed by Raman spectra helped to understand the high efficient upconversion emission of Y₇O₆F₉ and the main phonon vibration of Y₇O₆F₉ lies at 472 cm⁻¹, which is far lower that of Y₂O₃ (at 708 cm⁻¹). Our results indicate that orthorhombic rare earth ions doped Y₇O₆F₉ is an efficient matrix for UV and blue UC emission, and has potential applications in color displays, anti-counterfeiting and multicolor fluorescent labels.     

Spectra and intensity parameters of Tm ion in YAlO3 crystal

High quality Tm-doped YAlO₃ (Tm:YAlO₃) single crystals were obtained along crystallographic b-axis by the Czochralski technique. Optical absorption and fluorescence spectra for Tm³⁺ in YAlO₃ crystals were investigated at room temperature. Based on Judd-Ofelt approach, the intensity parameters Ω_t (t = 2, 4, 6) of Tm:YAlO₃ were calculated to be Ω₂ = 0.93 × 10⁻²⁰  cm², Ω₄ = 2.23 × 10⁻²⁰ cm², and Ω₆ = 1.12 × 10⁻²⁰ cm². The spectral parameters such as experimental and theoretical oscillator strengths, radiative transition probabilities, radiative lifetime and the fluorescence branching ratio were also obtained. All results indicate that Tm:YAlO₃ is a potential candidate for compact, efficient mid-infrared lasers with laser diode pumping.     

Energy transfer and upconversion of Nd doped RbY2Cl7

Single crystals of Nd³⁺:RbY₂Cl₇ were grown by the Bridgman-Stockbarger method. The host crystal contains two slightly inequivalent Y³⁺ ions, each with an approximate C_2v site symmetry. Anti-Stokes emission from the ⁴G_7/2 and ⁴D_3/2 levels was observed after laser excitation of the ⁴F_3/2 and ⁴F_9/2 multiplets. Laser excitation at 413 cm⁻¹ or 453 cm⁻¹ above the ⁴F_3/2 multiplet resulted in emission from the ²P_1/2 level. Laser site-selective upconverted emission spectra have been measured, as well as their emission transients and power dependence. Possible excited state absorption and energy-transfer upconversion (ETU) mechanisms are proposed and discussed. Due to the smaller crystal field and a somewhat different energy level structure for the Nd³⁺ ions in RbY₂Cl₇ as compared with those observed for Nd³⁺ in fluoride or oxide hosts, the ⁴G_7/2 and ⁴D_3/2 multiplets are populated under ⁴F_3/2 excitation in a three and four step ETU process, respectively, instead of in a two and three step process as observed for the lighter hosts.     

Preparation of the La0.8Sr0.2MnO3 films on STO and LAO substrates by excimer laser-assisted metal organic deposition using the KrF laser

La_0.8Sr_0.2MnO₃ films were prepared on SrTiO₃ (STO) and LaAlO₃ (LAO) substrates using excimer laser-assisted metal organic deposition (ELAMOD). For the LAO substrate, no epitaxial La_0.8Sr_0.2MnO₃ film was obtained by laser irradiation in the fluence range from 60 to 110 mJ/cm² with heating at 500 °C. On the other hand, an epitaxial La_0.8Sr_0.2MnO₃ film on the STO substrate was formed by laser irradiation in the fluence range from 60 to 100 mJ/cm² with heating at 500 °C. To optimize the electrical properties for an IR sensor, the effects of the laser fluence, the irradiation time and the film thickness on the temperature dependence of the resistance and temperature coefficient of resistance (TCR: defined as 1/R·(dR/dT)) of the LSMO films were investigated. An LSMO film on the STO substrate that showed the maximum TCR of 3.9% at 265 K was obtained by the ELAMOD process using the KrF laser.