Fiber-optic-coupled RbMgF3:Eu for remote radiation dosimetry

A portable fiber optic dosimeter has been developed that incorporates RbMgF₃:Eu²⁺ at the end of a multimode polymer fiber. It uses two stimulation sources and takes advantage of the range of stimulable traps in this compound. We observe radioluminescence (RL) during gamma ray irradiation and show that the low-dose RL increases linearly with increasing dose rate where the minimum detectible dose rate is ∼0.015 μSv/s. We show that pulsed infrared-stimulated (940 nm) optically stimulated luminescence (OSL) can be used for real time dose monitoring. The cumulative dose can be readout after irradiation where a linear OSL dose response was observed when stimulating at 505 nm and the minimum detectable dose is ∼50 μSv.     

Medical dosimetry using a RL/OSL prototype

A portable and robust instrument has been developed for the routine assessment of patient exposure to ionizing radiation during radiotherapy treatments. The design principles of hardware and software are described, along with preliminary measurements that illustrate the operation of the system and its capabilities. In this study the authors used radioluminescence (RL) and Optically Stimulated Luminescence (OSL) from Al₂O₃:C detectors coupled to a PMMA optical fibre to acquire dose in medical dosimetry. The RL/OSL prototype can provide two independent dose estimates from the same in vivo treatment: one integrated dose estimate (OSL) and one real-time dose estimate (RL), which can be compared to one another. The authors first characterized the dose–response to a calibration source (¹³⁷Cs), analysing the OSL and the RL signal to doses from 0.5 to 3 Gy. Later the percentage dose depth from RL is presented for two gamma (6 and 15 MV) and two electron (6 and 12 MeV) medical beams.     

Ionization density dependence of the curve shape and ratio of blue to UV emissions of Al2O3:C optically stimulated luminescence detectors exposed to 6-MV photon and therapeutic proton beams

In this work we characterized the dose and linear energy transfer (LET) (ionization density) dependence of commercial Al₂O₃:C optically stimulated luminescence (OSL) detectors (OSLDs) exposed to clinical photon and proton beams. We characterized the dose-dependence of the OSL signal, OSL curve shape, and the relative intensities of the blue and ultraviolet (UV) OSL emission bands using different readout protocols and beam qualities. We irradiated OSLDs with absorbed doses ranging from 0.1 Gy to 100 Gy in a 6-MV photon beam and from 0.1 Gy to 50 Gy in 140- and 250-MeV proton beams. Readouts were done with both continuous-wave (CWOSL) and pulsed (POSL) stimulation. The linearity of the OSLD dose–response depended on readout protocol and radiation type. Improved linearity was found for OSLDs irradiated with beams of increased LET, and for OSL signals containing only the blue emission band of Al₂O₃:C (which remained linear for doses up to 10 Gy for 140-MeV proton beam irradiations). The OSL curve shape did not vary with dose in the low-dose region (below 5 Gy depending on readout protocol), but beyond this, curves decayed more rapidly with increasing dose. Similarly, the ratio of blue to UV emission band intensities in the OSL signal did not vary with dose up to 5 Gy (depending on readout protocol), beyond which the ratio decreased with increasing dose. Because both the OSL curve shape and the ratio of blue to UV emission intensities have been investigated as potential parameters for measurements of LET, the constancy of these two quantities at doses relevant to radiotherapy is encouraging for the potential development of novel OSL methods to measure LET. Our findings are expected to contribute to the development of (i) improved readout protocols for commercially available Al₂O₃:C OSLDs and (ii) methods to measure radiation quality and LET.     

Characteristics of LiAlO2 – Radioluminescence and optically stimulated luminescence

Radioluminescence (RL) and optically stimulated luminescence (OSL) results of LiAlO₂ were compared with Al₂O₃:C. For blue (470 nm) optical stimulation, RL + OSL signal in LiAlO₂ exhibited a sharp initial increase followed by a decay within the first 20 s of continuous wave (CW)-OSL and a very slow increase thereafter. The RL + OSL signal was about 1.25 times of its RL signal in LiAlO₂ as compared to 2.5 times in Al₂O₃:C. With the continued beta irradiation, the RL signal exhibited a faster growth in LiAlO₂ than that in Al₂O₃:C. Emission spectrum of LiAlO₂ exhibited multiple emission peaks in the range from 320 to 380 nm as against 410 nm of Al₂O₃:C. RL and OSL emission spectra were similar in both LiAlO₂ and Al₂O₃:C. The intense RL in LiAlO₂ (about 300 times of that of its background signal) for a beta ray dose rate of 4.6 mGy/s appears attractive for radiation dosimetry including real time/online dosimetry and dose mapping.     

Role of Ti in the luminescence process of Al2O3:Si,Ti

Al₂O₃:Si,Ti, prepared under oxidizing condition at high temperature, gives PL emission around 430 nm when excited with 240 nm. The Al₂O₃:C, TL/OSL phosphor, also shows emission around 430 nm, which corresponds to characteristic emission of F-center. Thus, to identify the exact nature of luminescent center in Al₂O₃:Si,Ti, fluorescence lifetime measurement studies were carried out along with the PL,TL and OSL studies. The PL and TL in Al₂O₃:Si,Ti show emission around 430 nm and the time-resolved fluorescence studies show lifetime of about 43 μs for the 430 nm emission, which is much smaller than the reported lifetime of ∼35 ms for the 430 nm emission (F-center emission) in Al₂O₃:C phosphor. Therefore, the emission observed in Al₂O₃:Si,Ti phosphor was assigned to Ti⁴⁺ charge transfer transition. Fluorescence studies of Al₂O₃:Si,Ti do not show any traces of F and F⁺ centers. Also, Ti⁴⁺ does not show any change in the charge state after gamma-irradiation. On the basis of the above studies, a mechanism for TSL/OSL process in Al₂O₃:Si,Ti is proposed.     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

Piezoelectric properties of [Li0.03(K0.48Na0.52)0.97](Nb0.97Sb0.03)O3-(Ba0.85Ca0.15)(Ti0.90Zr0.10)O3 lead-free piezoelectric ceramics

[Li_0.03(K_0.48Na_0.52)_0.97](Nb_0.97Sb_0.03)O₃-(Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ [(1−x)LKNNS-xBCTZ] lead-free piezoelectric ceramics were prepared by the conventional solid state method, and effects of BCTZ content on the piezoelectric properties of LKNNS ceramics were mainly investigated. A stable solid solution has been formed between LKNNS and BCTZ, and a morphotropic phase boundary of (1−x)LKNNS-xBCTZ ceramics is identified in the range of 0 < x ≤ 0.02. The Curie temperature of (1−x)LKNNS-xBCTZ ceramics decreases with increasing BCTZ content. A higher ?_r value and a lower tan δ value are demonstrated for the (1−x)LKNNS-xBCTZ ceramic with x = 0.02. The (1−x)LKNNS-xBCTZ ceramic with x = 0.02 has an enhanced electrical behavior of d₃₃ ∼ 237 pC/N, k_p ∼ 48.6%, ?_r ∼ 1451, tan δ ∼ 0.037, and T_c ∼ 335 °C. As a result, (1−x)LKNNS-xBCTZ ceramics are promising candidate materials for the field of lead-free piezoelectric materials.     

Phase stability,elastic, electronic,thermal and optical properties of Ti3Al1−xSixC2 (0≤x≤1): First principle study

The structural parameters with stability upon Si incorporation and elastic, electronic, thermodynamic and optical properties of Ti₃Al_1−xSi_xC₂ (0≤x≤1) are investigated systematically by the plane wave pseudopotential method based on the density functional theory (DFT). The increase of some elastic parameters with increasing Si-content renders the alloys to possess higher compressive and tensile strength. The Vickers hardness value obtained with the help of Mulliken population analysis increases as x is increased from 0 to 1. The solid solutions considered are all metallic with valence and conduction bands, which have a mainly Ti 3d character, crossing the Fermi level. The temperature and pressure dependences of bulk modulus, normalized volume, specific heats, thermal expansion coefficient, and Debye temperature are all obtained through the quasi-harmonic Debye model with phononic effects for T=0−1000 K and P=0−50 GPa. The obtained results are compared with other results available. Further an analysis of optical functions for two polarization vectors reveals that the reflectivity is high in the visible–ultraviolet region up to ∼10.5 eV region showing promise as a good coating material.     

Energy transfer and luminescent properties of Ce, Cr co-doped Y3Al5O12

The phosphors in the system Y_3−xAl_5-yO₁₂:xCe³⁺,yCr³⁺ were synthesized by solid-state reactions and their photoluminescence properties were investigated. These phosphors have absorption in the visible light region and give luminescence in the far-red region (∼688 nm), which are suitable for the application in the device of luminescent solar concentrator (LSC). In these phosphors, Ce³⁺ located at Y³⁺ site can effectively transfer its absorbed energy to Cr³⁺ at Al³⁺ site.     

Investigation of a fibre-coupled beryllium oxide (BeO) ceramic luminescence dosimetry system

The purpose of this study is to investigate the potential use of a beryllium oxide (BeO) ceramic as a radioluminescence (RL) and optically stimulated luminescence (OSL) probe material for fibre-coupled luminescence dosimetry. A portable dosimetry system, named RL/OSL BeO FOD was developed, consisting of a 1 mm diameter, 1 mm long BeO ceramic cylinder coupled to a silica/silica optical fibre. The reader measures the RL signal and also uses a 450 nm laser diode to stimulate the BeO ceramic. A second background optical fibre is used to remove the stem effect. The RL/OSL BeO FOD was characterised in a solid water phantom, using a 6 MV x-ray beam. The RL was found to be reproducible and have a linear response to doses ranging from 30 cGy–15 Gy and dose rates from 100 cGy/min – 600 cGy/min. The OSL response was linear to doses of 10 Gy, becoming supralinear at higher doses. Measured percentage depth curves using the RL/OSL BeO FOD agreed with those measured using an IC15 ion chamber to within 5%, beyond the build up region. It was also found that the RL from BeO ceramic is unaffected by the delivered dose to the probe and hence, it remains constant for a given dose-rate. The insensitivity of the RL to accumulated dose makes BeO ceramic potentially capable of accurate dose-rate measurements without any corrections for the accumulated dose. This study demonstrates the feasibility of BeO ceramic as a versatile fibre-coupled luminescence dosimeter probe.     

Luminescence of Ce and Pr doped Sr2Mg(BO3)2 under VUV-UV and X-ray excitation

This report presents the luminescence properties of Ce³⁺ and Pr³⁺ activated Sr₂Mg(BO₃)₂ under VUV-UV and X-ray excitation. The five excitation bands of crystal field split 5d states are observed at about 46 729, 44 643, 41 667, 38 314 and 29 762 cm⁻¹ (i.e. 214, 224, 240, 261 and 336 nm) for Ce³⁺ in the host lattice. The doublet Ce³⁺ 5d→4f emission bands were found at about 25 840 and 24 096 cm⁻¹ (387 and 415 nm). The influence of doping concentration and temperature on the emission characteristics and the decay time of Ce³⁺ in Sr₂Mg(BO₃)₂ were investigated. For Pr³⁺ doped samples, the lowest 5d excitation band was observed at about 42017 cm⁻¹ (238 nm), a dominant band at around 35714 cm⁻¹ (280 nm) and two shoulder bands were seen in the emission spectra. The excitation and emission spectra of Ce³⁺ and Pr³⁺ were compared and discussed. The X-ray excited luminescence studies show that the light yields are ∼3200±230 and ∼1400±100 photons/MeV of absorbed X-ray energy for the samples Sr_1.86Ce_0.07Na_0.07Mg(BO₃)₂ and Sr_1.82Pr_0.09Na_0.09Mg(BO₃)₂ at RT, respectively.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Optically stimulated luminescence from CaSO4:Eu – Preliminary results

A new OSL phosphor CaSO₄:Eu was developed. The phosphor shows good OSL sensitivity which is about 55% of commercially available Al₂O₃:C. The phosphor also shows good TL sensitivity and the dosimetric peak, which appears around 186 °C, has sensitivity nearly 50% of Al₂O₃:C. After OSL readout of the irradiated sample, the TL peak around 250 °C depletes completely, with partial depletion of peak around 186 °C. Since the traps responsible for the high temperature peak are involved for the observed OSL, the sample shows low post-irradiation fading. The OSL decay is similar to Al₂O₃:C. Thus this phosphor due to its good OSL sensitivity, linear dose response, low fading and simple preparation technique could be useful for radiation dosimetry applications.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

Optical properties of Mn-activated Na2SnF6 and Cs2SnF6 red phosphors

Alkaline hexafluorostantanate red phosphors Na₂SnF₆:Mn⁴⁺ and Cs₂SnF₆:Mn⁴⁺ are synthesized by chemical reaction in HF/NaMnO₄ (CsMnO₄)/H₂O₂/H₂O mixed solutions immersed with tin metal. X-ray diffraction patterns suggest that the synthesized phosphors have a tetragonal symmetry with the space group D_4h¹⁴ (Na₂SnF₆:Mn⁴⁺) and a trigonal symmetry with the space group D_3d³ (Cs₂SnF₆:Mn⁴⁺). Photoluminescence (PL) analysis, PL excitation (PLE) spectroscopy, and the Raman scattering techniques are used to investigate the optical properties of the phosphors. The Franck-Condon analysis of the PLE data yields the Mn⁴⁺-related optical transitions to occur at ∼2.39 and ∼2.38 eV (⁴A_2g→⁴T_2g) and at ∼2.83 and ∼2.76 eV (⁴A_2g→⁴T_1g) for Na₂SnF₆:Mn⁴⁺ and Cs₂SnF₆:Mn⁴⁺, respectively. The crystal field parameters (Dq) of the Mn⁴⁺ ions in the Na₂SnF₆ and Cs₂SnF₆ hosts are determined to be ∼1930 and ∼1920 cm⁻¹, respectively. Temperature-dependent PL measurements are performed from 20 to 440 K in steps of 10 K, and the obtained results are interpreted by taking into account the Bose-Einstein occupation factor. Comprehensive discussion is given on the phosphorescent properties of a family of Mn⁴⁺-activated alkaline hexafluoride salts.     

Fiber-coupled Al2O3:C radioluminescence dosimetry for total body irradiations

In vivo dosimetry can be important and relevant in radiotherapy, especially when commissioning new treatment techniques at hospitals. This study investigates the potential use of fiber-coupled radioluminescence (RL) dosimetry based on Al₂O₃:C or organic plastic scintillators for this purpose in the context of Total Body Irradiations (TBIs) where patients are treated with large fields of 6 or 18 MV photons at an extended source-to-surface distance (SSD). The study shows that Al₂O₃:C dosimetry using the saturated-RL protocol may be suitable for real-time in vivo dosimetry during TBI treatments from the perspective of the good agreement with alanine dosimetry and other critical phantom tests, including the ability to cope with the large stem signal experienced during TBI treatments at extended SSD. In contrast, the chromatic stem removal technique often used for organic plastic scintillators did not work well in large fields with the tested calibration procedure and instrumentation. An apparent dose-rate effect discussed in a previous study of the RL properties of Al₂O₃:C (Andersen et al., 2011) was found to have resulted from an overlooked dead time problem in the counting system, and this potential caveat can therefore be removed from the list of potential problems associated with fiber-coupled Al₂O₃:C dosimetry using the saturated-RL protocol. This further has implications for TBI dosimetry using the RL Al₂O₃:C system due to large dose-rate differences between calibrations at the iso-center and in vivo measurements at extended source-to-surface distances.     

Oxide coatings on Y3Al5O12:Tb particles

A coating method with precipitating process was developed to reduce the particle size and to improve the particle dispersion of Y₃Al₅O₁₂:Tb³⁺ phosphor prepared by sol-gel method. The particle morphology was observed by using SEM and TEM; and the particle size and its dispersion was measured by using laser scattering technique. Several coating materials were tested. Among them, Al₂(SiO₃)₃ coating not only reduced the particle size from several micrometers to ∼1 μm and improved the particle dispersion, but also well kept luminescent intensities and improved the duration of the phosphor under the bombardment of cathode ray. The mechanism of the particle size reduction was proposed.     

Magnetic anisotropy of UFe6Al6

A comparative study of magnetization in UFe₆Al₆ and LuFe₆Al₆ single crystals gives clear evidence for the magnetic state of uranium in UFe₆Al₆. Both compounds exhibit the easy-plane type of magnetic anisotropy, however, the anisotropy energy in UFe₆Al₆, characterized by the anisotropy constants K₁=−7.3 MJ m⁻³ and K₂=−1.25 MJ m⁻³ at 2 K, exceeds by an order of magnitude that in LuFe₆Al₆. Anisotropy within the easy plane in the ferromagnetic state and anisotropy in the paramagnetic range, both absent in LuFe₆Al₆, are observed in UFe₆Al₆.     

Theoretical research on optical properties and quantum efficiency of Ga1−xAlxN photocathodes

In order to design the optimal component structure of transmission-mode (t-mode) Ga_1−xAl_xN photocathode, the optical properties and quantum efficiency of Ga_1−xAl_xN photocathodes are simulated. Based on thin film principle, optical model of t-mode Ga_1−xAl_xN photocathodes is built. And the quantum efficiency formula is put forward. Results show that Ga_1−xAl_xN photocathodes can satisfy the need of detectors with “solar blind” property when the Al component is bigger than 0.375. There is an optimal thickness of Ga_1−xAl_xN layer to get highest quantum efficiency, and the optimal thickness is 0.3 μm. There is close relation between absorptivity and quantum efficiency, which is in good agreement with the “three-step” model. This work gives a reference for the experimental research on the Ga_1−xAl_xN photocathodes.