CONCERTED H-BONDING TEMPLATE SYNTHESIS OF AN ORDERED LADDER POLYSILSESQUIOXANE

A novel soluble regular ladder poly（benzoyl-3-aminopropyl） silsesquioxane （LPBAS） was facilely prepared under effective assistance of concerted H-bonding self-assembly of amido groups of side chains and silanol groups, respectively, of a new template monomer [1,3-bis（benzoyl-3-aminopropyl）-1,1,3,3-tetraethoxydisiloxane] （M）. The ordered ladder structure of LPBAS is manifested in： （1） the presence of two Bragg peaks representing the ladder width （d） and ladder thickness （t） in X-ray diffraction （XRD） pattern; （2） narrow base-line width （w = 6） of resonance absorption for -CH2SiO3/2 moiety in 29Si-NMR and （3） high glass transition temperature Tg = 1 12℃ in differential scanning calorimetry （DSC） analysis.     

Supramolecular template-directed synthesis of perfect phenelenediimino-bridged ladderlike polyphenylsiloxanes

A template synthesis of the soluble, high molecular weight (Mw), and perfect p-phenylenediimino (p-PDA)-bridged ladderlike polyphenylsiloxane (PLPS) is reported. First, N,N'-bis(phenyldichlorosilyl)-p-PDA monomers were self-assembled into a perfect ladder superstructure (LS) by concerted interaction of aromatic pi-pi stacking and hydrogen bonding. Then the LS underwent a novel stoichiometric hydrolysis/dehydrochlorination-condensation reaction instead of the usual hydrolysis/dehydration-condensation reaction, leading to the PLPS. The perfect ladder structures of both the PLPS and, in particular, the unstable supramolecular LS were confirmed as follows. 1) There are two Bragg peaks in solid and/or solution X-ray diffraction (XRD) spectra representing the ladder width (w) and ladder thickness (t); these peaks were consistent with those calculated by molecular simulation. 2) Both the PLPS and LS have extremely sharp absorption peaks with small half-peak widths (Delta(1/2) < 0.3 ppm) in 29Si NMR spectra, suggesting the presence of the perfect ladder structure for PLPS and LS. 3) Moreover, no noticeable absorption peaks for the Si-OH and NH2 groups were observed in FT-IR and 29Si NMR spectra, indicating that the Si-N bond of the [triple bond]Si-NH-C6H4-NH-Si[triple bond] ladder rung of PLPS and LS is not cleaved. 4) Both PLPS and LS show similar emission peaks (in fluorescence spectroscopy) attributed to the excimer formed by face-to face pi-pi stacking of phenyl groups along the ladder chain rather than a branched direction. 5) Differential scanning calorimetry (DSC) measurements indicate a high glass temperature (Tg = 176.4 degrees C) for PLPS. As circumstantial evidence, this result further indicates very high stiffness of PLPSs ladder backbone as compared with flexible single-chain polyphenylmethylsiloxane with a low Tg = -69.4 degrees C.     

SYNTHESIS AND CHARACTERIZATION OF AN ORDERED LADDER POLYESTER

An ordered ladder polyester （LPE） was first synthesized through the ladder superstructure （LS） constructed by concerted interactions of hydroxyl- and aramide-based H-bonding and p-terphenyl （TP）-based π-stacking by dehydrochlorination condensation using phosgene （COCl2） as coupling agent. LPE was characterized by GPC, FTIR, NMR, XRD, DSC and AFM. Among them, a distinct image of regularly linear alignment corresponding to the ladder main chain of LPE was first revealed by high-resolution AFM.     

H-BONDING SELF-ASSEMBLED TEMPLATE-CONTROLLED SYNTHESIS OF A NOVEL SOLUBLE AND REACTIVE AMIDE-BRIDGED LADDERLIKE POLYHYDROSILOXANE

A novel soluble and reactive amide-bridged ladderlike polyhydrosiloxane （ALPHS） was first synthesized by an amido H-bonding self-assembled template. ALPHS with molecular weight M^-a = 18300 has very highly ordered ladderlike structure, which was confirmed by a sharp resonance absorption peak of [-Si（H）O2/2 ] moiety with the half peak width △1/2 〈 0.5 in^29Si-NMR spectrum. Presence of the reactive Si-H groups gives ALPHS an opportunity to further derive a variety of functional polymers by versatile Si-H reactions such as hydrosilylation, condensation, and so on.     

金纳米粒子的非线性共振散射及光强度函数研究

液相金纳米粒子在320nm、470nm、580nm720nm处产生四个共振散射峰。它是一种非线性光学介质,当入射光的频率v不同时可获得金纳米粒子的2v倍频、v/2分频、v/3分频、2v/3 分频、3v／2分频散射峰。探讨了影响液相金纳米粒子散射光信号强度I（λ）的主要因素即散射光能量分布、粒径d、△λ（λem-λex)和散射光辐射度Rλex。给出了共振散射光强度与△λ之间的高斯分布函数。建立了一个合理的金纳米粒子的共振散射光强度函数。     

柑桔溃疡菌的共振散射光谱

研究了柑桔溃疡菌的共振散射光谱,在330、425、465和695 nm产生四个共振散射峰.当激发波长为330 nm （9.09×1014 Hz）时,溃疡菌溶液在330 nm（9.09×1014 Hz）、660 nm（1/2×9.09×1014 Hz）和990 nm（1/3×9.09×1014 Hz）分别产生一共振散射峰和1/2、1/3两个分频散射峰;当激发波长为465 nm（6.45×1014 Hz）时,在456 nm(6.45×1014 Hz)和930 nm(1/2×6.45×1014 Hz)分别产生一个共振散射峰和一个1/2分频射峰; 当激发波长为930 nm(3.23×1014 Hz)时,在930 nm (3.23×1014 Hz)、620 nm(3/2×3.23×1014 Hz)、465 nm(2×3.23×1014 Hz) 和310 nm (3×3.23×1014 Hz)分别产生一个共振散射峰,一个3/2分频共振散射峰,一个2倍频共振散射峰和一个3倍频共振散射峰.柑桔溃疡菌是一种非线性散射光学介质.分频散射和倍频散射峰与共振散射峰具有相似的散射行为.     

超分子构筑调控合成结构规整的梯形聚合物及其应用研究

综述了"超分子构筑调控的逐步偶联/聚合法",该方法将高分子化学与超分子化学相结合,利用多种类型的超分子弱键协同作用首先构筑预期的梯形超分子结构,再经聚合得到共价键梯形高分子.利用该方法合成了一系列结构规整的氧桥基和有机桥基梯形聚硅氧烷以及碳基梯形聚酯,并利用侧基间π-π叠加作用实现了对聚合物立体构型控制.扼要介绍了梯形聚合物在先进材料方面的应用,例如梯形聚硅氧烷液晶光致取向膜;由梯形聚硅氧烷合成的管状聚硅氧烷在高室温储存期微电子环氧塑封料方面的应用;以及基于梯形聚硅氧烷的拟筛板聚合物在二阶非线性光学材料方面的应用等.     

Modern spectrum analysis in multidimensional NMR spectroscopy: comparison of linear-prediction extrapolation and maximum-entropy reconstruction

NMR spectroscopy is an inherently insensitive technique, and many challenging applications such as biomolecular studies operate at the very limits of sensitivity and resolution. Advances in superconducting magnet, cryogenic probe, and pulse sequence technologies have resulted in dramatic improvements in both sensitivity and resolution in the past decade. Conversely, the signal-processing method used most widely in NMR spectroscopy, extrapolation of the time domain signal by linear prediction (LP) followed by discrete Fourier transformation (DFT), was developed in the early 1980s and has not been subjected to detailed scrutiny for its impact on sensitivity and resolution. Here we report the first systematic investigation of the accuracy and precision of spectra obtained by LP extrapolation followed by DFT. We compare the results to spectra obtained by maximum-entropy (MaxEnt) reconstruction, which was developed contemporaneously to LP extrapolation but is not widely employed in NMR spectroscopy. Although it reduces truncation artifacts and increases the amplitudes of strong peaks, we find that LP extrapolation generates false-positive peaks and introduces frequency errors. These defects of LP extrapolation become less pronounced for longer data records and higher signal-to-noise ratio. MaxEnt generally yields more detectable peaks for a given number of data samples, more accurate peak frequencies, and fewer false-positive peaks than LP extrapolation. MaxEnt also permits the use of nonlinear sampling, which can give dramatic improvements in resolution. These results show that the use of MaxEnt together with nonlinear sampling, rather than LP extrapolation, could reduce the amount of instrument time required for adequate sensitivity and resolution by a factor of 2 or more.     

用质谱和光电子能谱研究飞秒强场中的电离动力学

报导了用自制飞秒激光器通过飞秒多光子电离质谱和光电子能谱对飞秒强激光场与分子（氨、苯）相互作用的研究。飞秒激光脉宽约100fs,二倍频中心波长407.5nm,聚焦后脉冲功率密度达到1012W/cm2。氨的光电子能谱显示了（2+2）REMPI和（2+2）+1ATI、（2+2）+2ATI三组电子峰,每组峰又包括伸缩振动v1的带系,ATI峰的振动布居出现反转。随着光强增加,谱峰加宽而且振动能级出现平移。这些强场效应可用PonderomotivePotential解释。苯的飞秒质谱图与纳秒情况不同,分子离子为主,碎片峰很少。     

Influence of static strain on dynamic mechanical behavior of amorphous networks prepared from aromatic polyesters

Dynamic mechanical experiments were performed between ?140 and 50°C on both poly(diethylene glycol isophthalate) and poly(triethylene glycol terephthalate) networks. Plots of loss tangent versus temperature show a well-defined α peak, associated with the transition from glasslike to rubberlike consistency, and two overlapping peaks (β₁ and β₂) in the glassy region. Dynamic deformations of small amplitude were superimposed on large static deformations. It was found that the position of the β₁ and β₂ peaks as well as their intensities are independent of the static elongation ratio. However, the intensity of the loss tangent associated with the glass–rubber transition tends to decrease with increasing static deformation. Moreover, the position of the maximum of the α peaks shifts to lower temperatures as the elongation ratio increases. This behavior suggests that for both networks the volume effects (shifting the α peaks to lower temperatures with increasing elongation ratio) overcome the entropic effects (shifting the α peaks to higher temperatures with decreasing entropy).     

Polarographic study of uracil derivatives

Eighteen uracil derivatives were studied by d.c. polarography, differential-pulse (d.p.)polarography and d.p. cathodic stripping voltammetry. In a borax buffer at ca. pH 7.6, uracil, thymine and derivatives such as 5-halouracils, 5-trifluoromethyl-,5-aza-,5-acetyl-, 5-formyl- and 5-vinyl-uracil produced well-defined peaks at potentials between 0 V and ca. 160 mV vs. silver/ silver chloride (satd. KCl). The peaks are ascribed to the formation of sparingly soluble mercury salts. For the other derivatives tested (e.g., 5-nitro- and 5-ethynyl-uracil and 6-substituted uracils), the peaks were less well-defined and in some cases the polarographic curves were very complex. 2-Thiouracil produced a single peak at ca. ?400 mV, but only at pH 12.2. The shapes, heights and potentials of the peaks depended on the kind and position of the substituent on the pyrimidine ring. Rectilinear relationships of peak current vs. concentrations were found for most compounds (10^?5-10^?4 M) by d.p. polarography; d.c.polarography was not tested quantitatively. For 5-fluorouracil and 5-vinyluracil, linear calibrations were found for concentrations of 0.5–5 × 10^?7 M by d.p. cathodic stripping voltametry. Interference studies showed that small amounts of chloride and phosphate did not interfere but 5-fluorodeoxyuridine, which did not itself produce a peak, and proteins interfered seriously.     

水合醛缩酶热变性的DSC研究

本文采用差示扫描量热法(DSC),研究了水合醛缩酶在含水量h从0.08g/g至2.28g/g范围内的热变性行为。实验结果表明,当h=0.08g/g时,水合醛缩酶样品的温度扫描热谱图呈现了两个吸热峰,其中低温峰很小,高温峰很大。随着h的增大,低温峰变得更小,高温峰则出现了分峰现象。当h=0.22g/g时,低温峰消失,高温峰则分裂成了两个独立的吸热峰。随着h的继续增大,其中前峰的位置不断移向低温,直至h_0.65g/g时,才不再变化。后峰的位置则始终保持不变。当再进行第二次温度扫描时,前峰消失,而后峰却能再现。本文给出了两峰在不同含水量时的转变温度、转变焓和转变焓之和,以及它们与含水量的关系。最后,对上述诸峰的起因作了分析讨论,认为低温峰可能起因于水合醛缩酶结晶的熔化作用,前峰和后峰可能起因于醛缩酶中两种A亚基的热变性。     

ESR study of free radicals in mango

An electron spin resonance (ESR) spectroscopic study of radicals induced in irradiated fresh mangoes was performed. Mangoes in the fresh state were irradiated with γ-rays, lyophilized and then crushed into a powder. The ESR spectrum of the powder showed a strong main peak at g = 2.004 and a pair of peaks centered at the main peak. The main peak was detected from both flesh and skin specimens. This peak height gradually decreased during storage following irradiation. On the other hand, the side peaks showed a well-defined dose–response relationship even at 9 days post-irradiation. The side peaks therefore provide a useful means to define the irradiation of fresh mangoes.     

Syntheses, solid-state structures, and solution studies by VT 31P NMR of [Zn[Se2P(OEt)2]2] infinity and [Zn2[Se2P(OiPr)2]4

Complexes [Zn[Se(2)P(OEt)(2)](2)]( infinity ) (1) and [Zn(2)[Se(2)P(O(i)Pr)(2)](4)] (2) are prepared from the reaction of Zn(ClO(4))(2).6H(2)O and (NH(4))[Se(2)P(OR)(2)] (R = Et and (i)Pr) in a molar ratio of 1:2 in deoxygenated water at room temperature. Positive FAB mass spectra show m/z peaks at 968.8 (Zn(2)L(3)(+)) and 344.8 (ZnL(+)) for 1 and m/z at 1052.8 (Zn(2)L(3)(+)) for 2. (1)H NMR spectra exhibit chemical shifts at delta 1.43 and 4.23 ppm for 1 and 1.41 and 4.87 ppm for 2 due to Et and (i)Pr group of dsep ligands. While the solid-state structure of compound 1 is a one-dimensional polymer via symmetrically bridging dsep ligands, complex 2 in the crystalline state exists as a dimer. In both 1 and 2, zinc atoms are connected by two bridging dsep ligands with an additional chelating ligand at each zinc atom. The dsep ligands exhibit bimetallic biconnective (micro(2), eta(2)) and monometallic biconnective (eta(2)) coordination patterns. Thus, each zinc atom is coordinated by four selenium atoms from two bridging and one chelating dsep ligands and the geometry around zinc is distorted tetrahedral. The Zn-Se distances range between 2.422 and 2.524 A. From variable-temperature (31)P NMR studies it has been found that monomer and dimer of the complex are in equilibrium in solution via exchange of bridging and chelating ligands. However, at temperature above 40 degrees C the complex exists as a monomer and shows a very sharp peak while with lowering of the temperature the percentage of dimer increases gradually at the expense of monomer. Below -90 degrees C the complex exists as a dimer and two peaks are observed with equal intensities which are due to bridging and chelating ligands. (77)Se NMR spectra of both complexes at -30 degrees C exhibit three doublets due to the presence of monomer and dimer in solution.     

高规整梯形聚乙烯基倍半硅氧烷的合成

采用具有"同步增长,同步断撑和原位缩合"特性的超分子构筑调控逐步偶联和聚合方法,合成了高规整的反应性梯形聚乙烯基倍半硅氧烷Vi-LPSQ.该反应性乙烯基可进一步功能化,是制备功能高分子材料的重要前驱体.29Si-NMR是表征梯形聚合物规整性最有效的方法,Vi-LPSQ的重复结构单元共振吸收峰的化学位移δ=-21.6,且峰宽Δca.1,说明其规整性很高.它的XRD谱图上存在两个明显的衍射峰,分别对应于梯形的宽度(d1=0.74 nm)和厚度(d2=0.40 nm),这证实了Vi-LPSQ以典型的梯形结构存在.另外,Vi-LPSQ的玻璃化转变温度Tg高达191.3℃,表明Vi-LPSQ分子具有很高的刚性和规整性.     

热分析法研究超高分子量聚乙烯的热熔性质

本文采用差热分析(DTA)、差示扫描量热法(DSC)研究了一系列以高效催化聚合而得的初生态超高分子量(M_w=70-315×10⁴)聚乙烯粉的热熔行为,还研究了在接近熔化或部分熔化的温度下恒温热处理对晶体性质的影响.     

Peak‐fitting of high resolution ToF‐SIMS spectra: a preliminary study

Peak‐fitting has been performed on a series of peaks obtained by time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) analysis in order to assess whether information may be obtained from this procedure on the samples' characteristics. A variety of samples were examined including a range of treatments for aluminium leading to different surface roughnesses, polymer films with a range of polydispersities, molecular weight (MW) and thicknesses as well as aluminium samples with adsorbed adhesion promoters on the surface. Variation of peak‐fitting was assessed by varying the peak intensity, full width at half maximum (FWHM) and peak asymmetry. Although further studies are needed it is possible to say that the peak width increases with roughness whereas peak asymmetry seems to be related to oxide thickness. Polymer characteristics do not seem to influence the width whereas the peak asymmetry increases either versus MW or polydispersity. A possible assumption is that the peak asymmetry relates to the ion formation processes. Additional work with varying polymer films thickness indicates that both FWHM and peak asymmetry may be related to sample charging and this could be used for assessment of film thicknesses. Finally, peak‐fitting was used to obtain a more reliable peak area when peaks are too close in mass to use current methods. Copyright © 2009 John Wiley & Sons, Ltd.     

Parametric studies of matched filters to enhance the signal-to-noise ratios of LC-MS-MS peaks

Chromatographic parameters of reference signals employed in matched filter methods have been studied using numerical experiments to improve the signal-to-noise (S/N) ratios of small liquid chromatography (LC) peaks obtained with electrospray tandem mass spectrometers (MS-MS). These parameters include the width, shape, and S/N ratios of chromatographic peaks used as the reference signal profiles. Our results show the effect of reference peak widths on improving the S/N ratio of chromatographic peaks; the influence of reference peak shapes is negligible. To verify simulation results, various reference signals, including analyte peaks of high concentration standards, internal standard peaks, and artificial Gaussian peaks of different widths, have been employed to enhance signal peaks on real liquid chromatography-tandem mass spectrometry (LC-MS-MS) chromatograms via matched filter methods. Our experimental results demonstrate that the S/N ratio enhancement of chromatographic peaks agree with the simulation predictions. These findings, therefore, suggest that regardless of peak shape, a well-smooth peak with a width close to that of the analyte peak is an adequate reference signal, when matched filter methods are used to improve LC-MS-MS chromatograms. Nevertheless, all methods processed LC-MS-MS peaks in this study do not achieve the ideal improvement ratios estimated with simulation results. We attribute this deficiency to spike-like noise, which have considerable low frequency components riding on LC-MS-MS chromatograms. Matched filtering, which works as a low-pass filter in the frequency domain, cannot effectively eliminate low frequency flicker noise contributed by these spikes. In addition, simple median filtering does not provide adequate improvement despite being able to smooth out most spikes in the chromatograms.     

Vibrational spectroscopic encoding of polystyrene-based resin beads: converting the encoding peaks into barcodes

A detailed approach is described for the vibrational spectroscopic encoding of polystyrene-based resin beads by converting the infrared absorption peaks suitable for encoding (encoding peaks) into barcodes. Based on combining the FT-IR measurements and the quantum-chemical computations, the vibrational characteristics of p-tert-butylstyrene monomer, polystyrene and poly(p-tert-butylstyrene) resin beads are analyzed, which are helpful for the selection of encoding peaks. The vibrational spectroscopic encoding of polystyrene-based resin beads could be obtained by converting the wavenumber, intensity and full width at half maximum (FWHM) of the encoding peaks into barcodes automatically through a computer program designed in our laboratory.     

纳米结晶体Ni0.5Zn0.5Fe2O4对高氯酸铵热行为及分解反应动力学的影响

采用差示扫描量热法(DSC)、热重和微分热重(TG-DTG)及固相原位反应池/快速扫描傅立叶变换红外联用技术(hyphenated in situ thermolysis/RSFTIR)研究了纳米结晶体Ni_0.5Zn_0.5Fe₂O₄与高氯酸铵(AP)组成的混合物的热行为和分解反应动力学。结果表明：Ni_0.5Zn_0.5Fe₂O₄使得AP的低、高温分解放热峰温分别提前17.44 K和27.74 K,并使得对应的分解热分别增加3.7 J·g^-1和193.7 J·g^-1。Ni_0.5Zn_0.5Fe₂O₄并不影响AP的晶转温度和晶转热。Ni_0.5Zn_0.5Fe₂O₄使得AP的TG曲线出现3个阶段,并使得后2个失重阶段的初始和终止温度都有所提前。凝聚相分解产物分析表明Ni_0.5Zn_0.5Fe₂O₄加速了凝聚相AP的分解及氨气的释放。含Ni_0.5Zn_0.5Fe₂O₄的AP的高温分解反应的动力学参数E_a=238.88 kJ·mol^-1,A=1018.59 s^-1,动力学方程可表示为dα/dt=10^18.99(1-α)[-ln(1-α)]^3/5e^-2.87×104T。始点温度(T_e)和峰顶温度(T_p)计算得出AP的热爆炸临界温度值分别为:574.83 K和595.41 K。分解反应的活化熵(ΔS^≠)、活化焓(ΔH^≠)和活化能(ΔG^≠)分别为:109.61 J·mol^-1·K^-1、236.49 kJ·mol^-1及172.58 kJ·mol^-1。